| Age | Commit message (Collapse) | Author |
|---|
|
Adding the PTP related firmware interface is the main change.
There is also a name change for admin_mtu, requiring code fixup.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the PF is no longer enforcing an assigned MAC address on a VF, the
VF needs to call bnxt_approve_mac() to tell the PF what MAC address it is
now using. Otherwise it gets out of sync and the PF won't know what
MAC address the VF wants to use. Ultimately the VF will fail when it
tries to setup the L2 MAC filter for the vnic.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move it before bnxt_update_vf_mac(). In the next patch, we need to call
bnxt_approve_mac() from bnxt_update_mac() under some conditions. This
will avoid forward declaration.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is perfectly legal for the stack to query and configure VFs via PF
NDOs while the NIC is administratively down. Remove the unnecessary
check for the PF to be in open state.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware previously only allowed promiscuous mode for VFs associated with
a default VLAN. It is now possible to enable promiscuous mode for a VF
having no VLAN configured provided that it is trusted. In such cases the
VF will see all packets received by the PF, irrespective of destination
MAC or VLAN.
Note, it is necessary to query firmware at the time of bnxt_promisc_ok()
instead of in bnxt_hwrm_func_qcfg() because the trusted status might be
altered by the PF after the VF has been configured. This check must now
also be deferred because the firmware call sleeps.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
linux/netdevice.h is included in very many places, touching any
of its dependecies causes large incremental builds.
Drop the linux/ethtool.h include, linux/netdevice.h just needs
a forward declaration of struct ethtool_ops.
Fix all the places which made use of this implicit include.
Acked-by: Johannes Berg <johannes@sipsolutions.net>
Acked-by: Shannon Nelson <snelson@pensando.io>
Reviewed-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Link: https://lore.kernel.org/r/20201120225052.1427503-1-kuba@kernel.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The main changes include FEC, ECN statistics, HWRM_PORT_PHY_QCFG
response size reduction, and a new counter added to
ctx_hw_stats_ext struct to support the new 58818 chip.
The ctx_hw_stats_ext structure is now the superset supporting the new
58818 chips and the prior P5 chips. Add a new flag to identify the new
chip and use constants for the chip specific ring statistics sizes
instead of the size of the structure.
Because the HWRM_PORT_PHY_QCFG response structure size has shrunk back
to 96 bytes, the workaround added earlier to limit the size of this
message for forwarding to the VF can be removed.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Main changes are 200G support and fixing the definitions of discard and
error counters to match the hardware definitions.
Because the HWRM_PORT_PHY_QCFG message size has now exceeded the max.
encapsulated response message size of 96 bytes from the PF to the VF,
we now need to cap this message to 96 bytes for forwarding. The forwarded
response only needs to contain the basic link status and speed information
and can be capped without adding the new information.
v2: Fix bnxt_re compile error.
Cc: Selvin Xavier <selvin.xavier@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
we need to set 'active_vfs' back to 0, if something goes wrong during the
allocation of SR-IOV resources: otherwise, further VF configurations will
wrongly assume that bp->pf.vf[x] are valid memory locations, and commands
like the ones in the following sequence:
# echo 2 >/sys/bus/pci/devices/${ADDR}/sriov_numvfs
# ip link set dev ens1f0np0 up
# ip link set dev ens1f0np0 vf 0 trust on
will cause a kernel crash similar to this:
bnxt_en 0000:3b:00.0: not enough MMIO resources for SR-IOV
BUG: kernel NULL pointer dereference, address: 0000000000000014
#PF: supervisor read access in kernel mode
#PF: error_code(0x0000) - not-present page
PGD 0 P4D 0
Oops: 0000 [#1] SMP PTI
CPU: 43 PID: 2059 Comm: ip Tainted: G I 5.8.0-rc2.upstream+ #871
Hardware name: Dell Inc. PowerEdge R740/08D89F, BIOS 2.2.11 06/13/2019
RIP: 0010:bnxt_set_vf_trust+0x5b/0x110 [bnxt_en]
Code: 44 24 58 31 c0 e8 f5 fb ff ff 85 c0 0f 85 b6 00 00 00 48 8d 1c 5b 41 89 c6 b9 0b 00 00 00 48 c1 e3 04 49 03 9c 24 f0 0e 00 00 <8b> 43 14 89 c2 83 c8 10 83 e2 ef 45 84 ed 49 89 e5 0f 44 c2 4c 89
RSP: 0018:ffffac6246a1f570 EFLAGS: 00010246
RAX: 0000000000000000 RBX: 0000000000000000 RCX: 000000000000000b
RDX: 0000000000000001 RSI: 0000000000000000 RDI: ffff98b28f538900
RBP: ffff98b28f538900 R08: 0000000000000000 R09: 0000000000000008
R10: ffffffffb9515be0 R11: ffffac6246a1f678 R12: ffff98b28f538000
R13: 0000000000000001 R14: 0000000000000000 R15: ffffffffc05451e0
FS: 00007fde0f688800(0000) GS:ffff98baffd40000(0000) knlGS:0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000014 CR3: 000000104bb0a003 CR4: 00000000007606e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
PKRU: 55555554
Call Trace:
do_setlink+0x994/0xfe0
__rtnl_newlink+0x544/0x8d0
rtnl_newlink+0x47/0x70
rtnetlink_rcv_msg+0x29f/0x350
netlink_rcv_skb+0x4a/0x110
netlink_unicast+0x21d/0x300
netlink_sendmsg+0x329/0x450
sock_sendmsg+0x5b/0x60
____sys_sendmsg+0x204/0x280
___sys_sendmsg+0x88/0xd0
__sys_sendmsg+0x5e/0xa0
do_syscall_64+0x47/0x80
entry_SYSCALL_64_after_hwframe+0x44/0xa9
Fixes: c0c050c58d840 ("bnxt_en: New Broadcom ethernet driver.")
Reported-by: Fei Liu <feliu@redhat.com>
CC: Jonathan Toppins <jtoppins@redhat.com>
CC: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Jonathan Toppins <jtoppins@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts were all overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The firmware does not expect the CRC to be included in the length
passed from the driver. The firmware always configures the chip
to strip out the CRC.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix the logic that sets the enable/disable flag for the source MAC
filter according to firmware spec 1.7.1.
In the original firmware spec. before 1.7.1, the VF spoof check flags
were not latched after making the HWRM_FUNC_CFG call, so there was a
need to keep the func_flags so that subsequent calls would perserve
the VF spoof check setting. A change was made in the 1.7.1 spec
so that the flags became latched. So we now set or clear the anti-
spoof setting directly without retrieving the old settings in the
stored vf->func_flags which are no longer valid. We also remove the
unneeded vf->func_flags.
Fixes: 8eb992e876a8 ("bnxt_en: Update firmware interface spec to 1.7.6.2.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As part of converting error code in firmware message to standard
code, checking for firmware return code is removed in most of the
places. Remove the assignment of return code where the function
can directly return.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently only assignes 1 RSS context to each VF. This works
for the Linux VF driver. But other drivers, such as DPDK, can make use
of additional RSS contexts. Modify the code to divide up and assign
RSS contexts to VFs just like other resources.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Retain the VF MAC address, default VLAN, TX rate control, trust settings
of VFs after firmware reset.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new flag will be set in subsequent patches when firmware is
going through reset. If bnxt_close() is called while the new flag
is set, the FW reset sequence will have to be aborted because the
NIC is prematurely closed before FW reset has completed. We also
reject SRIOV configurations while FW reset is in progress.
v2: No longer drop rtnl_lock() in close and wait for FW reset to complete.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VFs need to be reconfigured dynamically after firmwware reset, the
configuration sequence on the PF needs to be changed to register the VF
buffers first. Otherwise, some VF firmware commands may not succeed as
there may not be PF buffers ready for the re-directed firmware commands.
This sequencing did not matter much before when we only supported
the normal bring-up of VFs.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor the hardware/firmware configuration portion in
bnxt_sriov_enable() into a new function bnxt_cfg_hw_sriov(). This
new function can be called after a firmware reset to reconfigure the
VFs previously enabled.
v2: straight refactor of the code. Reordering done in the next patch.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are 4 functions handling message forwarding for SR-IOV. They
check for non-zero firmware response code and then return -1. There
is no need to do this anymore. The main messaging function will
now return standard error code. Since we don't need to examine the
response, we can use the hwrm_send_message() variant which will
take the mutex automatically.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The main firmware messaging function returns the firmware defined error
code and many callers have to convert to standard error code for proper
propagation to userspace. Convert bnxt_hwrm_do_send_msg() to return
standard error code so we can do away with all the special error code
handling by the many callers.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer firmware understands the concept of a trusted VF, so propagate the
trusted VF attribute set by the PF admin. to the firmware. Also, check
the firmware trusted setting when considering the VF MAC address change
and reporting the trusted setting to the user.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are some minor differences when assigning VF resources on the
new chips. The MSIX (NQ) resource has to be assigned and ring group
is not needed on the new chips.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For bnxt_en driver, stat_ctxs created will always be same as
cp_nr_rings. Remove extra variable that duplicates the value.
Also introduce bnxt_get_avail_stat_ctxs_for_en() helper to get
available stat_ctxs and bnxt_get_ulp_stat_ctxs() helper to return
number of stat_ctxs used by RDMA.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The available CP rings are calculated differently on the new 57500
chips, so add this helper to do this calculation correctly. The
VFs will be assigned these available CP rings.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The recent commit to always forward the VF MAC address to the PF for
approval may not work if the PF driver or the firmware is older. This
will cause the VF driver to fail during probe:
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): hwrm req_type 0xf seq id 0x5 error 0xffff
bnxt_en 0000:00:03.0 (unnamed net_device) (uninitialized): VF MAC address 00:00:17:02:05:d0 not approved by the PF
bnxt_en 0000:00:03.0: Unable to initialize mac address.
bnxt_en: probe of 0000:00:03.0 failed with error -99
We fix it by treating the error as fatal only if the VF MAC address is
locally generated by the VF.
Fixes: 707e7e966026 ("bnxt_en: Always forward VF MAC address to the PF.")
Reported-by: Seth Forshee <seth.forshee@canonical.com>
Reported-by: Siwei Liu <loseweigh@gmail.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the driver adjusts the bp->hw_resc.max_cp_rings by the number
of MSIX vectors used by RDMA. There is one code path in open that needs
to check the true max_cp_rings including any used by RDMA. This code
is now checking for the reduced max_cp_rings which will fail when the
number of cp rings is very small.
To fix this in a clean way, we don't adjust max_cp_rings anymore.
Instead, we add a helper bnxt_get_max_func_cp_rings_for_en() to get the
reduced max_cp_rings when appropriate.
Fixes: ec86f14ea506 ("bnxt_en: Add ULP calls to stop and restart IRQs.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BNXT_FLAG_NEW_RM flag is checked a lot in the code to determine if
the new resource manager is in effect. Define a macro to perform
this check.
Signed-off-by: Michael Chan <michael.chan@broadocm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new mode is "minimal-static" to be used when resources are more
limited to support a large number of VFs, for example The PF driver
will provision guaranteed minimum resources of 0. Each VF has no
guranteed resources until it tries to reserve resources during device
open.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The else-if branch and else branch set mac_ok to true similarly,
so combine the two into single else branch.
Also add comments to explain the two conditions, which
from Michael Chan and Vasundhara Volam.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code already forwards the VF MAC address to the PF, except
in one case. If the VF driver gets a valid MAC address from the firmware
during probe time, it will not forward the MAC address to the PF,
incorrectly assuming that the PF already knows the MAC address. This
causes "ip link show" to show zero VF MAC addresses for this case.
This assumption is not correct. Newer firmware remembers the VF MAC
address last used by the VF and provides it to the VF driver during
probe. So we need to always forward the VF MAC address to the PF.
The forwarded MAC address may now be the PF assigned MAC address and so we
need to make sure we approve it for this case.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For completeness and correctness, the VF driver needs to reserve these
RSS and L2 contexts.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware messages that are forwarded from PF to VFs are encapsulated.
The size of these encapsulated messages must not exceed the maximum
defined message size. Add appropriate checks to avoid oversize
messages. Firmware messages may be expanded in future specs and
this will provide some guardrails to avoid data corruption.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When firmware sends a DMA response to the driver, the last byte of the
message will be set to 1 to indicate that the whole response is valid.
The driver waits for the message to be valid before reading the message.
The firmware spec allows these response messages to increase in
length by adding new fields to the end of these messages. The
older spec's valid location may become a new field in a newer
spec. To guarantee compatibility, the driver should zero the valid
byte before interpreting the entire message so that any new fields not
implemented by the older spec will be read as zero.
For messages that are forwarded to VFs, we need to set the length
and re-instate the valid bit so the VF will see the valid response.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VFs are created, the current code subtracts the maximum VF
resources from the PF's pool. This under-estimates the resources
remaining in the PF pool. Instead, we should subtract the minimum
VF resources. The VF minimum resources are guaranteed to the VFs
and only these should be subtracted from the PF's pool.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trusted VFs are allowed to modify MAC address, even when PF
has assigned one.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Forward hwrm_func_vf_cfg command from VF to PF driver, to store
VF MAC address in PF's context. This will allow "ip link show"
to display all VF MAC addresses.
Maintain 2 locations of MAC address in VF info structure, one for
a PF assigned MAC and one for VF assigned MAC.
Display VF assigned MAC in "ip link show", only if PF assigned MAC is
not valid.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of the old method of evenly dividing the resources to the VFs,
use the new firmware API to specify min and max resources for each VF.
This way, there is more flexibility for each VF to allocate more or less
resources.
The min is the absolute minimum for each VF to function. The max is the
global resources minus the resources used by the PF. Each VF is
guaranteed the min. Up to max resources may be available for some VFs.
The PF driver can use one of 2 strategies specified in NVRAM to assign
the resources. The old legacy strategy of evenly dividing the resources
or the new flexible strategy.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for new firmware APIs to allocate hardware resources,
add a new struct bnxt_hw_resc to hold various min, max and reserved
resources. This new structure is common for PFs and VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bnxt_vf_ndo_prep (which is called by bnxt_get_vf_config ndo), there is a
check for "Invalid VF id". Currently, the check is done against max_vfs.
However, the user doesn't always create max_vfs. So, the check should be
against the created number of VFs. The number of bnxt_vf_info structures
that are allocated in bnxt_alloc_vf_resources routine is the "number of
requested VFs". So, if an "invalid VF id" falls between the requested
number of VFs and the max_vfs, the driver will be dereferencing an invalid
pointer.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Venkat Devvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In bnxt_sriov_enable(), we calculate to see if we have enough hardware
resources to enable the requested number of VFs. The logic to check
for minimum completion rings and statistics contexts is missing. Add
the required checks so that VF configuration won't fail.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch is a part of a patch-set that introduces support for
VF-reps in the bnxt_en driver. The driver registers eswitch mode
get/set methods with the devlink interface that allow a user to
enable SRIOV switchdev mode. When enabled, the driver registers
a VF-rep netdev object for each VF with the stack. This can
essentially bring the VFs unders the management perview of the
hypervisor and applications such as OVS.
The next patch in the series, adds the RX/TX routines and a slim
netdev implementation for the VF-reps.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VF representors and PTP are added features in the new firmware spec.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .ndo_get_vf_config() is returning the wrong qos attribute. Fix
the code that checks and reports the qos and spoofchk attributes. The
BNXT_VF_QOS and BNXT_VF_LINK_UP flags should not be set by default
during init. time.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Features added include WoL and selftest.
Signed-off-by: Deepak Khungar <deepak.khungar@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the ulp_sriov_cfg callbacks when the number of VFs is changing. This
allows the RDMA driver to provision RDMA resources for the VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to properly support TX rate limiting in SRIOV VF functions or
NPAR functions, firmware needs better control over tx ring allocations.
The new scheme requires the driver to reserve the number of tx rings
and to query to see if the requested number of tx rings is reserved.
The driver will use the new scheme when the firmware interface spec is
1.6.1 or newer.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Assign additional vnics to VFs whenever possible so that NTUPLE can be
supported on the VFs.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All available remaining completion rings not used by the PF should be
made available for the VFs so that there are enough rings in the VF to
support RDMA. The earlier workaround code of capping the rings by the
statistics context is removed.
When SRIOV is disabled, call a new function bnxt_restore_pf_fw_resources()
to restore FW resources. Later on we need to add some logic to account
for RDMA resources.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Latest interface has the latest DCB command structs. Get and store the
max number of lossless TCs the hardware can support.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the physical link is down and the VF virtual link is set to "enable",
the current code does not always work. If the link is down but the
cable is attached, the firmware returns LINK_SIGNAL instead of
NO_LINK. The current code is treating LINK_SIGNAL as link up.
The fix is to treat link as down when the link_status != LINK.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
