| Age | Commit message (Collapse) | Author |
|---|
|
Each completion ring entry has a valid bit to indicate that the entry
contains a valid completion event. The driver's main poll loop
__bnxt_poll_work() has the proper dma_rmb() to make sure the valid
bit of the next entry has been checked before proceeding further.
But when we call bnxt_rx_pkt() to process the RX event, the RX
completion event consists of two completion entries and only the
first entry has been checked to be valid. We need the same barrier
after checking the next completion entry. Add missing dma_rmb()
barriers in bnxt_rx_pkt() and other similar locations.
Fixes: 67a95e2022c7 ("bnxt_en: Need memory barrier when processing the completion ring.")
Reported-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Lance Richardson <lance.richardson@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
212 firmware broke aRFS, so disable it. Traffic may stop after ntuple
filters are inserted and deleted by the 212 firmware.
Fixes: ae10ae740ad2 ("bnxt_en: Add new hardware RFS mode.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers should count packets they are dropping.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
skbs are freed on error and not put on the ring. We may, however,
be in a situation where we're freeing the last skb of a batch,
and there is a doorbell ring pending because of xmit_more() being
true earlier. Make sure we ring the door bell in such situations.
Since errors are rare don't pay attention to xmit_more() and just
always flush the pending frames.
The busy case should be safe to be left alone because it can
only happen if start_xmit races with completions and they
both enable the queue. In that case the kick can't be pending.
Noticed while reading the code.
Fixes: 4d172f21cefe ("bnxt_en: Implement xmit_more.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
napi schedules DIM, napi has to be disabled first,
then DIM canceled.
Noticed while reading the code.
Fixes: 0bc0b97fca73 ("bnxt_en: cleanup DIM work on device shutdown")
Fixes: 6a8788f25625 ("bnxt_en: add support for software dynamic interrupt moderation")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We can't take the tx lock from the napi poll routine, because
netpoll can poll napi at any moment, including with the tx lock
already held.
The tx lock is protecting against two paths - the disable
path, and (as Michael points out) the NETDEV_TX_BUSY case
which may occur if NAPI completions race with start_xmit
and both decide to re-enable the queue.
For the disable/ifdown path use synchronize_net() to make sure
closing the device does not race we restarting the queues.
Annotate accesses to dev_state against data races.
For the NAPI cleanup vs start_xmit path - appropriate barriers
are already in place in the main spot where Tx queue is stopped
but we need to do the same careful dance in the TX_BUSY case.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some older Broadcom debug tools use window 5 and may conflict, so switch
to use window 6 instead.
Fixes: 118612d519d8 ("bnxt_en: Add PTP clock APIs, ioctls, and ethtool methods")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New firmware interface requires the PTP sequence ID header offset to
be passed to the firmware to properly find the matching timestamp
for all protocols.
Fixes: 83bb623c968e ("bnxt_en: Transmit and retrieve packet timestamps")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The key change is the firmware call to retrieve the PTP TX timestamp.
The header offset for the PTP sequence number field is now added.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we return when bnxt_open() fails in bnxt_fw_reset_task(),
there is no need to check for 'rc' value again before invoking
bnxt_reenable_sriov().
Fixes: 3958b1da725a ("bnxt_en: fix error path of FW reset")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We use the timecounter APIs for the 48-bit PHC and packet timestamps.
We must periodically update the timecounter at roughly half the
overflow interval. The overflow interval is about 78 hours, so
update it every 19 hours (1/4 interval) for some extra margins.
Fixes: 390862f45c85 ("bnxt_en: Get the full 48-bit hardware timestamp periodically")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current PTP initialization logic does not account for firmware
reset that may cause PTP capability to change. The valid pointer
bp->ptp_cfg is used to indicate that the device is capable of PTP
and that it has been initialized. So we must clean up bp->ptp_cfg
and free it if the firmware after reset does not support PTP.
Fixes: 93cb62d98e9c ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device needs to be in ifup state for PTP to function, so move
bnxt_ptp_init() to bnxt_open(). This means that the PHC will be
registered during bnxt_open().
This also makes firmware reset work correctly. PTP configurations
may change after firmware upgrade or downgrade. bnxt_open() will
be called after firmware reset, so it will work properly.
bnxt_ptp_start() is now incorporated into bnxt_ptp_init(). We now
also need to call bnxt_ptp_clear() in bnxt_close().
Fixes: 93cb62d98e9c ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt_half_open_nic() is called during during ethtool self test and is
protected by rtnl_lock. Firmware reset can be happening at the same
time. Only critical portions of the entire firmware reset sequence
are protected by the rtnl_lock. It is possible that bnxt_half_open_nic()
can be called when the firmware reset sequence is aborting. In that
case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set
and abort if it is. The ethtool self test will fail but the NIC will be
brought to a consistent IF_DOWN state.
Without this patch, if bnxt_half_open_nic() were to continue in this
error state, it may crash like this:
bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Process ethtool (pid: 333327, stack limit = 0x0000000046476577)
Call trace:
bnxt_alloc_mem+0x444/0xef0 [bnxt_en]
bnxt_half_open_nic+0x24/0xb8 [bnxt_en]
bnxt_self_test+0x2dc/0x390 [bnxt_en]
ethtool_self_test+0xe0/0x1f8
dev_ethtool+0x1744/0x22d0
dev_ioctl+0x190/0x3e0
sock_ioctl+0x238/0x480
do_vfs_ioctl+0xc4/0x758
ksys_ioctl+0x84/0xb8
__arm64_sys_ioctl+0x28/0x38
el0_svc_handler+0xb0/0x180
el0_svc+0x8/0xc
Fixes: a1301f08c5ac ("bnxt_en: Check abort error state in bnxt_open_nic().")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only pass supported VLAN protocol IDs for stripped VLAN tags to the
stack. The stack will hit WARN() if the protocol ID is unsupported.
Existing firmware sets up the chip to strip 0x8100, 0x88a8, 0x9100.
Only the 1st two protocols are supported by the kernel.
Fixes: a196e96bb68f ("bnxt_en: clean up VLAN feature bit handling")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When bnxt_open() fails in the firmware reset path, the driver needs to
gracefully abort, but it is executing code that should be invoked only
in the success path. Define a function to abort FW reset and
consolidate all error paths to call this new function.
Fixes: dab62e7c2de7 ("bnxt_en: Implement faster recovery for firmware fatal error.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all
VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after
we acquire the rtnl_lock. If the flag is set, we need to abort.
Fixes: 230d1f0de754 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The capabilities can change after firmware upgrade/downgrade, so we
should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe()
is called.
Fixes: 2151fe0830fd ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ETS proportions are presented to HWRM_QUEUE_COS2BW_CFG as minimum
bandwidth constraints. Thus, zero is a legal value for a given TC.
However, if all the other TCs sum up to 100%, then at least one
hardware queue will starve, resulting in guaranteed TX timeouts.
Reject such nonsensical configurations.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If device is already disabled in reset path and PCI io error is
detected before the device could be enabled, driver could
call pci_disable_device() for already disabled device. Fix this
problem by calling pci_disable_device() only if the device is already
enabled.
Fixes: 6316ea6db93d ("bnxt_en: Enable AER support.")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- BPF:
- add syscall program type and libbpf support for generating
instructions and bindings for in-kernel BPF loaders (BPF loaders
for BPF), this is a stepping stone for signed BPF programs
- infrastructure to migrate TCP child sockets from one listener to
another in the same reuseport group/map to improve flexibility
of service hand-off/restart
- add broadcast support to XDP redirect
- allow bypass of the lockless qdisc to improving performance (for
pktgen: +23% with one thread, +44% with 2 threads)
- add a simpler version of "DO_ONCE()" which does not require jump
labels, intended for slow-path usage
- virtio/vsock: introduce SOCK_SEQPACKET support
- add getsocketopt to retrieve netns cookie
- ip: treat lowest address of a IPv4 subnet as ordinary unicast
address allowing reclaiming of precious IPv4 addresses
- ipv6: use prandom_u32() for ID generation
- ip: add support for more flexible field selection for hashing
across multi-path routes (w/ offload to mlxsw)
- icmp: add support for extended RFC 8335 PROBE (ping)
- seg6: add support for SRv6 End.DT46 behavior
- mptcp:
- DSS checksum support (RFC 8684) to detect middlebox meddling
- support Connection-time 'C' flag
- time stamping support
- sctp: packetization Layer Path MTU Discovery (RFC 8899)
- xfrm: speed up state addition with seq set
- WiFi:
- hidden AP discovery on 6 GHz and other HE 6 GHz improvements
- aggregation handling improvements for some drivers
- minstrel improvements for no-ack frames
- deferred rate control for TXQs to improve reaction times
- switch from round robin to virtual time-based airtime scheduler
- add trace points:
- tcp checksum errors
- openvswitch - action execution, upcalls
- socket errors via sk_error_report
Device APIs:
- devlink: add rate API for hierarchical control of max egress rate
of virtual devices (VFs, SFs etc.)
- don't require RCU read lock to be held around BPF hooks in NAPI
context
- page_pool: generic buffer recycling
New hardware/drivers:
- mobile:
- iosm: PCIe Driver for Intel M.2 Modem
- support for Qualcomm MSM8998 (ipa)
- WiFi: Qualcomm QCN9074 and WCN6855 PCI devices
- sparx5: Microchip SparX-5 family of Enterprise Ethernet switches
- Mellanox BlueField Gigabit Ethernet (control NIC of the DPU)
- NXP SJA1110 Automotive Ethernet 10-port switch
- Qualcomm QCA8327 switch support (qca8k)
- Mikrotik 10/25G NIC (atl1c)
Driver changes:
- ACPI support for some MDIO, MAC and PHY devices from Marvell and
NXP (our first foray into MAC/PHY description via ACPI)
- HW timestamping (PTP) support: bnxt_en, ice, sja1105, hns3, tja11xx
- Mellanox/Nvidia NIC (mlx5)
- NIC VF offload of L2 bridging
- support IRQ distribution to Sub-functions
- Marvell (prestera):
- add flower and match all
- devlink trap
- link aggregation
- Netronome (nfp): connection tracking offload
- Intel 1GE (igc): add AF_XDP support
- Marvell DPU (octeontx2): ingress ratelimit offload
- Google vNIC (gve): new ring/descriptor format support
- Qualcomm mobile (rmnet & ipa): inline checksum offload support
- MediaTek WiFi (mt76)
- mt7915 MSI support
- mt7915 Tx status reporting
- mt7915 thermal sensors support
- mt7921 decapsulation offload
- mt7921 enable runtime pm and deep sleep
- Realtek WiFi (rtw88)
- beacon filter support
- Tx antenna path diversity support
- firmware crash information via devcoredump
- Qualcomm WiFi (wcn36xx)
- Wake-on-WLAN support with magic packets and GTK rekeying
- Micrel PHY (ksz886x/ksz8081): add cable test support"
* tag 'net-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2168 commits)
tcp: change ICSK_CA_PRIV_SIZE definition
tcp_yeah: check struct yeah size at compile time
gve: DQO: Fix off by one in gve_rx_dqo()
stmmac: intel: set PCI_D3hot in suspend
stmmac: intel: Enable PHY WOL option in EHL
net: stmmac: option to enable PHY WOL with PMT enabled
net: say "local" instead of "static" addresses in ndo_dflt_fdb_{add,del}
net: use netdev_info in ndo_dflt_fdb_{add,del}
ptp: Set lookup cookie when creating a PTP PPS source.
net: sock: add trace for socket errors
net: sock: introduce sk_error_report
net: dsa: replay the local bridge FDB entries pointing to the bridge dev too
net: dsa: ensure during dsa_fdb_offload_notify that dev_hold and dev_put are on the same dev
net: dsa: include fdb entries pointing to bridge in the host fdb list
net: dsa: include bridge addresses which are local in the host fdb list
net: dsa: sync static FDB entries on foreign interfaces to hardware
net: dsa: install the host MDB and FDB entries in the master's RX filter
net: dsa: reference count the FDB addresses at the cross-chip notifier level
net: dsa: introduce a separate cross-chip notifier type for host FDBs
net: dsa: reference count the MDB entries at the cross-chip notifier level
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fallthrough fixes from Gustavo Silva:
"Fix many fall-through warnings when building with Clang 12.0.0 and
'-Wimplicit-fallthrough' so that we at some point will be able to
enable that warning by default"
* tag 'fallthrough-fixes-clang-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux: (26 commits)
rxrpc: Fix fall-through warnings for Clang
drm/nouveau/clk: Fix fall-through warnings for Clang
drm/nouveau/therm: Fix fall-through warnings for Clang
drm/nouveau: Fix fall-through warnings for Clang
xfs: Fix fall-through warnings for Clang
xfrm: Fix fall-through warnings for Clang
tipc: Fix fall-through warnings for Clang
sctp: Fix fall-through warnings for Clang
rds: Fix fall-through warnings for Clang
net/packet: Fix fall-through warnings for Clang
net: netrom: Fix fall-through warnings for Clang
ide: Fix fall-through warnings for Clang
hwmon: (max6621) Fix fall-through warnings for Clang
hwmon: (corsair-cpro) Fix fall-through warnings for Clang
firewire: core: Fix fall-through warnings for Clang
braille_console: Fix fall-through warnings for Clang
ipv4: Fix fall-through warnings for Clang
qlcnic: Fix fall-through warnings for Clang
bnxt_en: Fix fall-through warnings for Clang
netxen_nic: Fix fall-through warnings for Clang
...
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-06-28
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 12 day(s) which contain
a total of 56 files changed, 394 insertions(+), 380 deletions(-).
The main changes are:
1) XDP driver RCU cleanups, from Toke Høiland-Jørgensen and Paul E. McKenney.
2) Fix bpf_skb_change_proto() IPv4/v6 GSO handling, from Maciej Żenczykowski.
3) Fix false positive kmemleak report for BPF ringbuf alloc, from Rustam Kovhaev.
4) Fix x86 JIT's extable offset calculation for PROBE_LDX NULL, from Ravi Bangoria.
5) Enable libbpf fallback probing with tracing under RHEL7, from Jonathan Edwards.
6) Clean up x86 JIT to remove unused cnt tracking from EMIT macro, from Jiri Olsa.
7) Netlink cleanups for libbpf to please Coverity, from Kumar Kartikeya Dwivedi.
8) Allow to retrieve ancestor cgroup id in tracing programs, from Namhyung Kim.
9) Fix lirc BPF program query to use user-provided prog_cnt, from Sean Young.
10) Add initial libbpf doc including generated kdoc for its API, from Grant Seltzer.
11) Make xdp_rxq_info_unreg_mem_model() more robust, from Jakub Kicinski.
12) Fix up bpfilter startup log-level to info level, from Gary Lin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call bnxt_ptp_init() to initialize and register with the clock driver
to enable PTP support. Call bnxt_ptp_free() to unregister and clean
up during shutdown.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setup the TXBD to enable TX timestamp if requested. At TX packet DMA
completion, if we requested TX timestamp on that packet, we defer to
.do_aux_work() to obtain the TX timestamp from the firmware before we
free the TX SKB.
v2: Use .do_aux_work() to get the TX timestamp from firmware.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the RX packet is timestamped by the hardware, the RX completion
record will contain the lower 32-bit of the timestamp. This needs
to be combined with the upper 16-bit of the periodic timestamp that
we get from the timer. The previous snapshot in ptp->old_timer is
used to make sure that the snapshot is not ahead of the RX timestamp
and we adjust for wrap-around if needed.
v2: Make ptp->old_time read access safe on 32-bit CPUs.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From the bnxt_timer(), read the 48-bit hardware running clock
periodically and store it in ptp->current_time. The previous snapshot
of the clock will be stored in ptp->old_time. The old_time snapshot
will be used in the next patches to compute the RX packet timestamps.
v2: Use .do_aux_work() to read the timer periodically.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the clock APIs to set/get/adjust the hw clock, and the related
ioctls and ethtool methods.
v2: Propagate error code from ptp_clock_register().
Add spinlock to serialize access to the timecounter. The
timecounter is accessed in process context and the RX datapath.
Read the PHC using direct registers.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Store PTP hardware info in a structure if hardware and firmware support PTP.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding the PTP related firmware interface is the main change.
There is also a name change for admin_mtu, requiring code fixup.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bnxt driver has rcu_read_lock()/rcu_read_unlock() pairs around XDP
program invocations. However, the actual lifetime of the objects referred
by the XDP program invocation is longer, all the way through to the call to
xdp_do_flush(), making the scope of the rcu_read_lock() too small. This
turns out to be harmless because it all happens in a single NAPI poll
cycle (and thus under local_bh_disable()), but it makes the rcu_read_lock()
misleading.
Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/bpf/20210624160609.292325-9-toke@redhat.com
|
|
bnxt_ethtool_init() may have allocated some memory and we need to
call bnxt_ethtool_free() to properly unwind if bnxt_init_one()
fails.
Fixes: 7c3809181468 ("bnxt_en: Refactor bnxt_init_one() and turn on TPA support on 57500 chips.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TQM fastpath ring needs to be sized to store both the requester
and responder side of RoCE QPs in TQM for supporting bi-directional
tests. Fix bnxt_alloc_ctx_mem() to multiply the RoCE QPs by a factor of
2 when computing the number of entries for TQM fastpath ring. This
fixes an RX pipeline stall issue when running bi-directional max
RoCE QP tests.
Fixes: c7dd7ab4b204 ("bnxt_en: Improve TQM ring context memory sizing formulas.")
Signed-off-by: Rukhsana Ansari <rukhsana.ansari@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a missing bnxt_probe_phy() call in bnxt_fw_init_one() to
rediscover the PHY capabilities after a firmware reset. This can cause
some PHY related functionalities to fail after a firmware reset. For
example, in multi-host, the ability for any host to configure the PHY
settings may be lost after a firmware reset.
Fixes: ec5d31e3c15d ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
There was a typo in the code that checks for 64K BNXT_PAGE_SHIFT in
bnxt_hwrm_set_pg_attr(). Fix it and make the code more understandable
with a new macro BNXT_SET_CTX_PAGE_ATTR().
Fixes: 1b9394e5a2ad ("bnxt_en: Configure context memory on new devices.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Otherwise, some of the recently added HyperV VF IDs would not be
recognized as VF devices and they would not initialize properly.
Fixes: 7fbf359bb2c1 ("bnxt_en: Add PCI IDs for Hyper-V VF devices.")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Jakub Kicinski pointed out that we need to handle ipv6 extension headers
and to explicitly check for supported tunnel types in
.ndo_features_check().
For ipv6 extension headers, the hardware supports up to 2 ext. headers
and each must be <= 64 bytes. For tunneled packets, the supported
packets are UDP with supported VXLAN and Geneve ports, GRE, and IPIP.
v3: More improvements based on Alexander Duyck's valuable feedback -
Remove the jump lable in bnxt_features_check() and restructure it
so that the TCP/UDP is check is consolidated in bnxt_exthdr_check().
v2: Add missing step to check inner ipv6 header for UDP and GRE tunnels.
Check TCP/UDP next header after skipping ipv6 ext headers for
non-tunneled packets and for inner ipv6.
(Both feedback from Alexander Duyck)
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Fixes: 1698d600b361 ("bnxt_en: Implement .ndo_features_check().")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Alexander Duyck <alexanderduyck@fb.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull pci updates from Bjorn Helgaas:
"Enumeration:
- Release OF node when pci_scan_device() fails (Dmitry Baryshkov)
- Add pci_disable_parity() (Bjorn Helgaas)
- Disable Mellanox Tavor parity reporting (Heiner Kallweit)
- Disable N2100 r8169 parity reporting (Heiner Kallweit)
- Fix RCiEP device to RCEC association (Qiuxu Zhuo)
- Convert sysfs "config", "rom", "reset", "label", "index",
"acpi_index" to static attributes to help fix races in device
enumeration (Krzysztof Wilczyński)
- Convert sysfs "vpd" to static attribute (Heiner Kallweit, Krzysztof
Wilczyński)
- Use sysfs_emit() in "show" functions (Krzysztof Wilczyński)
- Remove unused alloc_pci_root_info() return value (Krzysztof
Wilczyński)
PCI device hotplug:
- Fix acpiphp reference count leak (Feilong Lin)
Power management:
- Fix acpi_pci_set_power_state() debug message (Rafael J. Wysocki)
- Fix runtime PM imbalance (Dinghao Liu)
Virtualization:
- Increase delay after FLR to work around Intel DC P4510 NVMe erratum
(Raphael Norwitz)
MSI:
- Convert rcar, tegra, xilinx to MSI domains (Marc Zyngier)
- For rcar, xilinx, use controller address as MSI doorbell (Marc
Zyngier)
- Remove unused hv msi_controller struct (Marc Zyngier)
- Remove unused PCI core msi_controller support (Marc Zyngier)
- Remove struct msi_controller altogether (Marc Zyngier)
- Remove unused default_teardown_msi_irqs() (Marc Zyngier)
- Let host bridges declare their reliance on MSI domains (Marc
Zyngier)
- Make pci_host_common_probe() declare its reliance on MSI domains
(Marc Zyngier)
- Advertise mediatek lack of built-in MSI handling (Thomas Gleixner)
- Document ways of ending up with NO_MSI (Marc Zyngier)
- Refactor HT advertising of NO_MSI flag (Marc Zyngier)
VPD:
- Remove obsolete Broadcom NIC VPD length-limiting quirk (Heiner
Kallweit)
- Remove sysfs VPD size checking dead code (Heiner Kallweit)
- Convert VPF sysfs file to static attribute (Heiner Kallweit)
- Remove unnecessary pci_set_vpd_size() (Heiner Kallweit)
- Tone down "missing VPD" message (Heiner Kallweit)
Endpoint framework:
- Fix NULL pointer dereference when epc_features not implemented
(Shradha Todi)
- Add missing destroy_workqueue() in endpoint test (Yang Yingliang)
Amazon Annapurna Labs PCIe controller driver:
- Fix compile testing without CONFIG_PCI_ECAM (Arnd Bergmann)
- Fix "no symbols" warnings when compile testing with
CONFIG_TRIM_UNUSED_KSYMS (Arnd Bergmann)
APM X-Gene PCIe controller driver:
- Fix cfg resource mapping regression (Dejin Zheng)
Broadcom iProc PCIe controller driver:
- Return zero for success of iproc_msi_irq_domain_alloc() (Pali
Rohár)
Broadcom STB PCIe controller driver:
- Add reset_control_rearm() stub for !CONFIG_RESET_CONTROLLER (Jim
Quinlan)
- Fix use of BCM7216 reset controller (Jim Quinlan)
- Use reset/rearm for Broadcom STB pulse reset instead of
deassert/assert (Jim Quinlan)
- Fix brcm_pcie_probe() error return for unsupported revision (Wei
Yongjun)
Cavium ThunderX PCIe controller driver:
- Fix compile testing (Arnd Bergmann)
- Fix "no symbols" warnings when compile testing with
CONFIG_TRIM_UNUSED_KSYMS (Arnd Bergmann)
Freescale Layerscape PCIe controller driver:
- Fix ls_pcie_ep_probe() syntax error (comma for semicolon)
(Krzysztof Wilczyński)
- Remove layerscape-gen4 dependencies on OF and ARM64, add dependency
on ARCH_LAYERSCAPE (Geert Uytterhoeven)
HiSilicon HIP PCIe controller driver:
- Remove obsolete HiSilicon PCIe DT description (Dongdong Liu)
Intel Gateway PCIe controller driver:
- Remove unused pcie_app_rd() (Jiapeng Chong)
Intel VMD host bridge driver:
- Program IRTE with Requester ID of VMD endpoint, not child device
(Jon Derrick)
- Disable VMD MSI-X remapping when possible so children can use more
MSI-X vectors (Jon Derrick)
MediaTek PCIe controller driver:
- Configure FC and FTS for functions other than 0 (Ryder Lee)
- Add YAML schema for MediaTek (Jianjun Wang)
- Export pci_pio_to_address() for module use (Jianjun Wang)
- Add MediaTek MT8192 PCIe controller driver (Jianjun Wang)
- Add MediaTek MT8192 INTx support (Jianjun Wang)
- Add MediaTek MT8192 MSI support (Jianjun Wang)
- Add MediaTek MT8192 system power management support (Jianjun Wang)
- Add missing MODULE_DEVICE_TABLE (Qiheng Lin)
Microchip PolarFlare PCIe controller driver:
- Make several symbols static (Wei Yongjun)
NVIDIA Tegra PCIe controller driver:
- Add MCFG quirks for Tegra194 ECAM errata (Vidya Sagar)
- Make several symbols const (Rikard Falkeborn)
- Fix Kconfig host/endpoint typo (Wesley Sheng)
SiFive FU740 PCIe controller driver:
- Add pcie_aux clock to prci driver (Greentime Hu)
- Use reset-simple in prci driver for PCIe (Greentime Hu)
- Add SiFive FU740 PCIe host controller driver and DT binding (Paul
Walmsley, Greentime Hu)
Synopsys DesignWare PCIe controller driver:
- Move MSI Receiver init to dw_pcie_host_init() so it is
re-initialized along with the RC in resume (Jisheng Zhang)
- Move iATU detection earlier to fix regression (Hou Zhiqiang)
TI J721E PCIe driver:
- Add DT binding and TI j721e support for refclk to PCIe connector
(Kishon Vijay Abraham I)
- Add host mode and endpoint mode DT bindings for TI AM64 SoC (Kishon
Vijay Abraham I)
TI Keystone PCIe controller driver:
- Use generic config accessors for TI AM65x (K3) to fix regression
(Kishon Vijay Abraham I)
Xilinx NWL PCIe controller driver:
- Add support for coherent PCIe DMA traffic using CCI (Bharat Kumar
Gogada)
- Add optional "dma-coherent" DT property (Bharat Kumar Gogada)
Miscellaneous:
- Fix kernel-doc warnings (Krzysztof Wilczyński)
- Remove unused MicroGate SyncLink device IDs (Jiri Slaby)
- Remove redundant dev_err() for devm_ioremap_resource() failure
(Chen Hui)
- Remove redundant initialization (Colin Ian King)
- Drop redundant dev_err() for platform_get_irq() errors (Krzysztof
Wilczyński)"
* tag 'pci-v5.13-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (98 commits)
riscv: dts: Add PCIe support for the SiFive FU740-C000 SoC
PCI: fu740: Add SiFive FU740 PCIe host controller driver
dt-bindings: PCI: Add SiFive FU740 PCIe host controller
MAINTAINERS: Add maintainers for SiFive FU740 PCIe driver
clk: sifive: Use reset-simple in prci driver for PCIe driver
clk: sifive: Add pcie_aux clock in prci driver for PCIe driver
PCI: brcmstb: Use reset/rearm instead of deassert/assert
ata: ahci_brcm: Fix use of BCM7216 reset controller
reset: add missing empty function reset_control_rearm()
PCI: Allow VPD access for QLogic ISP2722
PCI/VPD: Add helper pci_get_func0_dev()
PCI/VPD: Remove pci_vpd_find_tag() SRDT handling
PCI/VPD: Remove pci_vpd_find_tag() 'offset' argument
PCI/VPD: Change pci_vpd_init() return type to void
PCI/VPD: Make missing VPD message less alarming
PCI/VPD: Remove pci_set_vpd_size()
x86/PCI: Remove unused alloc_pci_root_info() return value
MAINTAINERS: Add Jianjun Wang as MediaTek PCI co-maintainer
PCI: mediatek-gen3: Add system PM support
PCI: mediatek-gen3: Add MSI support
...
|
|
Pull rdma updates from Jason Gunthorpe:
"This is significantly bug fixes and general cleanups. The noteworthy
new features are fairly small:
- XRC support for HNS and improves RQ operations
- Bug fixes and updates for hns, mlx5, bnxt_re, hfi1, i40iw, rxe, siw
and qib
- Quite a few general cleanups on spelling, error handling, static
checker detections, etc
- Increase the number of device ports supported beyond 255. High port
count software switches now exist
- Several bug fixes for rtrs
- mlx5 Device Memory support for host controlled atomics
- Report SRQ tables through to rdma-tool"
* tag 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/rdma/rdma: (145 commits)
IB/qib: Remove redundant assignment to ret
RDMA/nldev: Add copy-on-fork attribute to get sys command
RDMA/bnxt_re: Fix a double free in bnxt_qplib_alloc_res
RDMA/siw: Fix a use after free in siw_alloc_mr
IB/hfi1: Remove redundant variable rcd
RDMA/nldev: Add QP numbers to SRQ information
RDMA/nldev: Return SRQ information
RDMA/restrack: Add support to get resource tracking for SRQ
RDMA/nldev: Return context information
RDMA/core: Add CM to restrack after successful attachment to a device
RDMA/cma: Skip device which doesn't support CM
RDMA/rxe: Fix a bug in rxe_fill_ip_info()
RDMA/mlx5: Expose private query port
RDMA/mlx4: Remove an unused variable
RDMA/mlx5: Fix type assignment for ICM DM
IB/mlx5: Set right RoCE l3 type and roce version while deleting GID
RDMA/i40iw: Fix error unwinding when i40iw_hmc_sd_one fails
RDMA/cxgb4: add missing qpid increment
IB/ipoib: Remove unnecessary struct declaration
RDMA/bnxt_re: Get rid of custom module reference counting
...
|
|
All callers pass 0 as offset. Therefore remove the parameter and use a
fixed offset 0 in pci_vpd_find_tag().
Link: https://lore.kernel.org/r/f62e6e19-5423-2ead-b2bd-62844b23ef8f@gmail.com
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
|
|
For UDP encapsultions, we only support the offloaded Vxlan port and
Geneve port. All other ports included FOU and GUE are not supported so
we need to turn off TSO and checksum features.
v2: Reverse the check for supported UDP ports to be more straight forward.
Reviewed-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If firmware is capable, set the IFF_SUPP_NOFCS flag to support the
sockets option to transmit packets without FCS. This is mainly used
for testing.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Support VF device IDs used by the Hyper-V hypervisor.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the PF is no longer enforcing an assigned MAC address on a VF, the
VF needs to call bnxt_approve_mac() to tell the PF what MAC address it is
now using. Otherwise it gets out of sync and the PF won't know what
MAC address the VF wants to use. Ultimately the VF will fail when it
tries to setup the L2 MAC filter for the vnic.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Move it before bnxt_update_vf_mac(). In the next patch, we need to call
bnxt_approve_mac() from bnxt_update_mac() under some conditions. This
will avoid forward declaration.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is perfectly legal for the stack to query and configure VFs via PF
NDOs while the NIC is administratively down. Remove the unnecessary
check for the PF to be in open state.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware previously only allowed promiscuous mode for VFs associated with
a default VLAN. It is now possible to enable promiscuous mode for a VF
having no VLAN configured provided that it is trusted. In such cases the
VF will see all packets received by the PF, irrespective of destination
MAC or VLAN.
Note, it is necessary to query firmware at the time of bnxt_promisc_ok()
instead of in bnxt_hwrm_func_qcfg() because the trusted status might be
altered by the PF after the VF has been configured. This check must now
also be deferred because the firmware call sleeps.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the current code, the driver will not shutdown the link during
IFDOWN if there are still VFs sharing the port. Newer firmware will
manage the link down decision when the port is shared by VFs, so
we can just call firmware to shutdown the port unconditionally and
let firmware make the final decision.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
