| Age | Commit message (Collapse) | Author |
|---|
|
Each completion ring entry has a valid bit to indicate that the entry
contains a valid completion event. The driver's main poll loop
__bnxt_poll_work() has the proper dma_rmb() to make sure the valid
bit of the next entry has been checked before proceeding further.
But when we call bnxt_rx_pkt() to process the RX event, the RX
completion event consists of two completion entries and only the
first entry has been checked to be valid. We need the same barrier
after checking the next completion entry. Add missing dma_rmb()
barriers in bnxt_rx_pkt() and other similar locations.
Fixes: 67a95e2022c7 ("bnxt_en: Need memory barrier when processing the completion ring.")
Reported-by: Lance Richardson <lance.richardson@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Lance Richardson <lance.richardson@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
212 firmware broke aRFS, so disable it. Traffic may stop after ntuple
filters are inserted and deleted by the 212 firmware.
Fixes: ae10ae740ad2 ("bnxt_en: Add new hardware RFS mode.")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Drivers should count packets they are dropping.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
skbs are freed on error and not put on the ring. We may, however,
be in a situation where we're freeing the last skb of a batch,
and there is a doorbell ring pending because of xmit_more() being
true earlier. Make sure we ring the door bell in such situations.
Since errors are rare don't pay attention to xmit_more() and just
always flush the pending frames.
The busy case should be safe to be left alone because it can
only happen if start_xmit races with completions and they
both enable the queue. In that case the kick can't be pending.
Noticed while reading the code.
Fixes: 4d172f21cefe ("bnxt_en: Implement xmit_more.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
napi schedules DIM, napi has to be disabled first,
then DIM canceled.
Noticed while reading the code.
Fixes: 0bc0b97fca73 ("bnxt_en: cleanup DIM work on device shutdown")
Fixes: 6a8788f25625 ("bnxt_en: add support for software dynamic interrupt moderation")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We can't take the tx lock from the napi poll routine, because
netpoll can poll napi at any moment, including with the tx lock
already held.
The tx lock is protecting against two paths - the disable
path, and (as Michael points out) the NETDEV_TX_BUSY case
which may occur if NAPI completions race with start_xmit
and both decide to re-enable the queue.
For the disable/ifdown path use synchronize_net() to make sure
closing the device does not race we restarting the queues.
Annotate accesses to dev_state against data races.
For the NAPI cleanup vs start_xmit path - appropriate barriers
are already in place in the main spot where Tx queue is stopped
but we need to do the same careful dance in the TX_BUSY case.
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some older Broadcom debug tools use window 5 and may conflict, so switch
to use window 6 instead.
Fixes: 118612d519d8 ("bnxt_en: Add PTP clock APIs, ioctls, and ethtool methods")
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
New firmware interface requires the PTP sequence ID header offset to
be passed to the firmware to properly find the matching timestamp
for all protocols.
Fixes: 83bb623c968e ("bnxt_en: Transmit and retrieve packet timestamps")
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The key change is the firmware call to retrieve the PTP TX timestamp.
The header offset for the PTP sequence number field is now added.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set the error code if bnx2x_alloc_fw_stats_mem() fails. The current
code returns success.
Fixes: ad5afc89365e ("bnx2x: Separate VF and PF logic")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that we return when bnxt_open() fails in bnxt_fw_reset_task(),
there is no need to check for 'rc' value again before invoking
bnxt_reenable_sriov().
Fixes: 3958b1da725a ("bnxt_en: fix error path of FW reset")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We use the timecounter APIs for the 48-bit PHC and packet timestamps.
We must periodically update the timecounter at roughly half the
overflow interval. The overflow interval is about 78 hours, so
update it every 19 hours (1/4 interval) for some extra margins.
Fixes: 390862f45c85 ("bnxt_en: Get the full 48-bit hardware timestamp periodically")
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current PTP initialization logic does not account for firmware
reset that may cause PTP capability to change. The valid pointer
bp->ptp_cfg is used to indicate that the device is capable of PTP
and that it has been initialized. So we must clean up bp->ptp_cfg
and free it if the firmware after reset does not support PTP.
Fixes: 93cb62d98e9c ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The device needs to be in ifup state for PTP to function, so move
bnxt_ptp_init() to bnxt_open(). This means that the PHC will be
registered during bnxt_open().
This also makes firmware reset work correctly. PTP configurations
may change after firmware upgrade or downgrade. bnxt_open() will
be called after firmware reset, so it will work properly.
bnxt_ptp_start() is now incorporated into bnxt_ptp_init(). We now
also need to call bnxt_ptp_clear() in bnxt_close().
Fixes: 93cb62d98e9c ("bnxt_en: Enable hardware PTP support")
Cc: Richard Cochran <richardcochran@gmail.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnxt_half_open_nic() is called during during ethtool self test and is
protected by rtnl_lock. Firmware reset can be happening at the same
time. Only critical portions of the entire firmware reset sequence
are protected by the rtnl_lock. It is possible that bnxt_half_open_nic()
can be called when the firmware reset sequence is aborting. In that
case, bnxt_half_open_nic() needs to check if the ABORT_ERR flag is set
and abort if it is. The ethtool self test will fail but the NIC will be
brought to a consistent IF_DOWN state.
Without this patch, if bnxt_half_open_nic() were to continue in this
error state, it may crash like this:
bnxt_en 0000:82:00.1 enp130s0f1np1: FW reset in progress during close, FW reset will be aborted
Unable to handle kernel NULL pointer dereference at virtual address 0000000000000000
...
Process ethtool (pid: 333327, stack limit = 0x0000000046476577)
Call trace:
bnxt_alloc_mem+0x444/0xef0 [bnxt_en]
bnxt_half_open_nic+0x24/0xb8 [bnxt_en]
bnxt_self_test+0x2dc/0x390 [bnxt_en]
ethtool_self_test+0xe0/0x1f8
dev_ethtool+0x1744/0x22d0
dev_ioctl+0x190/0x3e0
sock_ioctl+0x238/0x480
do_vfs_ioctl+0xc4/0x758
ksys_ioctl+0x84/0xb8
__arm64_sys_ioctl+0x28/0x38
el0_svc_handler+0xb0/0x180
el0_svc+0x8/0xc
Fixes: a1301f08c5ac ("bnxt_en: Check abort error state in bnxt_open_nic().")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only pass supported VLAN protocol IDs for stripped VLAN tags to the
stack. The stack will hit WARN() if the protocol ID is unsupported.
Existing firmware sets up the chip to strip 0x8100, 0x88a8, 0x9100.
Only the 1st two protocols are supported by the kernel.
Fixes: a196e96bb68f ("bnxt_en: clean up VLAN feature bit handling")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When bnxt_open() fails in the firmware reset path, the driver needs to
gracefully abort, but it is executing code that should be invoked only
in the success path. Define a function to abort FW reset and
consolidate all error paths to call this new function.
Fixes: dab62e7c2de7 ("bnxt_en: Implement faster recovery for firmware fatal error.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In the BNXT_FW_RESET_STATE_POLL_VF state in bnxt_fw_reset_task() after all
VFs have unregistered, we need to check for BNXT_STATE_ABORT_ERR after
we acquire the rtnl_lock. If the flag is set, we need to abort.
Fixes: 230d1f0de754 ("bnxt_en: Handle firmware reset.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The capabilities can change after firmware upgrade/downgrade, so we
should get the up-to-date RoCE capabilities everytime bnxt_ulp_probe()
is called.
Fixes: 2151fe0830fd ("bnxt_en: Handle RESET_NOTIFY async event from firmware.")
Reviewed-by: Somnath Kotur <somnath.kotur@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
ETS proportions are presented to HWRM_QUEUE_COS2BW_CFG as minimum
bandwidth constraints. Thus, zero is a legal value for a given TC.
However, if all the other TCs sum up to 100%, then at least one
hardware queue will starve, resulting in guaranteed TX timeouts.
Reject such nonsensical configurations.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If device is already disabled in reset path and PCI io error is
detected before the device could be enabled, driver could
call pci_disable_device() for already disabled device. Fix this
problem by calling pci_disable_device() only if the device is already
enabled.
Fixes: 6316ea6db93d ("bnxt_en: Enable AER support.")
Signed-off-by: Kalesh AP <kalesh-anakkur.purayil@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Make sure that we disable each of the TX and RX queues in the TDMA and
RDMA control registers. This is a correctness change to be symmetrical
with the code that enables the TX and RX queues.
Tested-by: Maxime Ripard <maxime@cerno.tech>
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setting the EXT_ENERGY_DET_MASK bit allows the port energy detection
logic of the internal PHY to prevent the system from sleeping. Some
internal PHYs will report that energy is detected when the network
interface is closed which can prevent the system from going to sleep
if WoL is enabled when the interface is brought down.
Since the driver does not support waking the system on this logic,
this commit clears the bit whenever the internal PHY is powered up
and the other logic for manipulating the bit is removed since it
serves no useful function.
Fixes: 1c1008c793fa ("net: bcmgenet: add main driver file")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next
Pull networking updates from Jakub Kicinski:
"Core:
- BPF:
- add syscall program type and libbpf support for generating
instructions and bindings for in-kernel BPF loaders (BPF loaders
for BPF), this is a stepping stone for signed BPF programs
- infrastructure to migrate TCP child sockets from one listener to
another in the same reuseport group/map to improve flexibility
of service hand-off/restart
- add broadcast support to XDP redirect
- allow bypass of the lockless qdisc to improving performance (for
pktgen: +23% with one thread, +44% with 2 threads)
- add a simpler version of "DO_ONCE()" which does not require jump
labels, intended for slow-path usage
- virtio/vsock: introduce SOCK_SEQPACKET support
- add getsocketopt to retrieve netns cookie
- ip: treat lowest address of a IPv4 subnet as ordinary unicast
address allowing reclaiming of precious IPv4 addresses
- ipv6: use prandom_u32() for ID generation
- ip: add support for more flexible field selection for hashing
across multi-path routes (w/ offload to mlxsw)
- icmp: add support for extended RFC 8335 PROBE (ping)
- seg6: add support for SRv6 End.DT46 behavior
- mptcp:
- DSS checksum support (RFC 8684) to detect middlebox meddling
- support Connection-time 'C' flag
- time stamping support
- sctp: packetization Layer Path MTU Discovery (RFC 8899)
- xfrm: speed up state addition with seq set
- WiFi:
- hidden AP discovery on 6 GHz and other HE 6 GHz improvements
- aggregation handling improvements for some drivers
- minstrel improvements for no-ack frames
- deferred rate control for TXQs to improve reaction times
- switch from round robin to virtual time-based airtime scheduler
- add trace points:
- tcp checksum errors
- openvswitch - action execution, upcalls
- socket errors via sk_error_report
Device APIs:
- devlink: add rate API for hierarchical control of max egress rate
of virtual devices (VFs, SFs etc.)
- don't require RCU read lock to be held around BPF hooks in NAPI
context
- page_pool: generic buffer recycling
New hardware/drivers:
- mobile:
- iosm: PCIe Driver for Intel M.2 Modem
- support for Qualcomm MSM8998 (ipa)
- WiFi: Qualcomm QCN9074 and WCN6855 PCI devices
- sparx5: Microchip SparX-5 family of Enterprise Ethernet switches
- Mellanox BlueField Gigabit Ethernet (control NIC of the DPU)
- NXP SJA1110 Automotive Ethernet 10-port switch
- Qualcomm QCA8327 switch support (qca8k)
- Mikrotik 10/25G NIC (atl1c)
Driver changes:
- ACPI support for some MDIO, MAC and PHY devices from Marvell and
NXP (our first foray into MAC/PHY description via ACPI)
- HW timestamping (PTP) support: bnxt_en, ice, sja1105, hns3, tja11xx
- Mellanox/Nvidia NIC (mlx5)
- NIC VF offload of L2 bridging
- support IRQ distribution to Sub-functions
- Marvell (prestera):
- add flower and match all
- devlink trap
- link aggregation
- Netronome (nfp): connection tracking offload
- Intel 1GE (igc): add AF_XDP support
- Marvell DPU (octeontx2): ingress ratelimit offload
- Google vNIC (gve): new ring/descriptor format support
- Qualcomm mobile (rmnet & ipa): inline checksum offload support
- MediaTek WiFi (mt76)
- mt7915 MSI support
- mt7915 Tx status reporting
- mt7915 thermal sensors support
- mt7921 decapsulation offload
- mt7921 enable runtime pm and deep sleep
- Realtek WiFi (rtw88)
- beacon filter support
- Tx antenna path diversity support
- firmware crash information via devcoredump
- Qualcomm WiFi (wcn36xx)
- Wake-on-WLAN support with magic packets and GTK rekeying
- Micrel PHY (ksz886x/ksz8081): add cable test support"
* tag 'net-next-5.14' of git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (2168 commits)
tcp: change ICSK_CA_PRIV_SIZE definition
tcp_yeah: check struct yeah size at compile time
gve: DQO: Fix off by one in gve_rx_dqo()
stmmac: intel: set PCI_D3hot in suspend
stmmac: intel: Enable PHY WOL option in EHL
net: stmmac: option to enable PHY WOL with PMT enabled
net: say "local" instead of "static" addresses in ndo_dflt_fdb_{add,del}
net: use netdev_info in ndo_dflt_fdb_{add,del}
ptp: Set lookup cookie when creating a PTP PPS source.
net: sock: add trace for socket errors
net: sock: introduce sk_error_report
net: dsa: replay the local bridge FDB entries pointing to the bridge dev too
net: dsa: ensure during dsa_fdb_offload_notify that dev_hold and dev_put are on the same dev
net: dsa: include fdb entries pointing to bridge in the host fdb list
net: dsa: include bridge addresses which are local in the host fdb list
net: dsa: sync static FDB entries on foreign interfaces to hardware
net: dsa: install the host MDB and FDB entries in the master's RX filter
net: dsa: reference count the FDB addresses at the cross-chip notifier level
net: dsa: introduce a separate cross-chip notifier type for host FDBs
net: dsa: reference count the MDB entries at the cross-chip notifier level
...
|
|
Trivial conflict in net/netfilter/nf_tables_api.c.
Duplicate fix in tools/testing/selftests/net/devlink_port_split.py
- take the net-next version.
skmsg, and L4 bpf - keep the bpf code but remove the flags
and err params.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux
Pull fallthrough fixes from Gustavo Silva:
"Fix many fall-through warnings when building with Clang 12.0.0 and
'-Wimplicit-fallthrough' so that we at some point will be able to
enable that warning by default"
* tag 'fallthrough-fixes-clang-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gustavoars/linux: (26 commits)
rxrpc: Fix fall-through warnings for Clang
drm/nouveau/clk: Fix fall-through warnings for Clang
drm/nouveau/therm: Fix fall-through warnings for Clang
drm/nouveau: Fix fall-through warnings for Clang
xfs: Fix fall-through warnings for Clang
xfrm: Fix fall-through warnings for Clang
tipc: Fix fall-through warnings for Clang
sctp: Fix fall-through warnings for Clang
rds: Fix fall-through warnings for Clang
net/packet: Fix fall-through warnings for Clang
net: netrom: Fix fall-through warnings for Clang
ide: Fix fall-through warnings for Clang
hwmon: (max6621) Fix fall-through warnings for Clang
hwmon: (corsair-cpro) Fix fall-through warnings for Clang
firewire: core: Fix fall-through warnings for Clang
braille_console: Fix fall-through warnings for Clang
ipv4: Fix fall-through warnings for Clang
qlcnic: Fix fall-through warnings for Clang
bnxt_en: Fix fall-through warnings for Clang
netxen_nic: Fix fall-through warnings for Clang
...
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-06-28
The following pull-request contains BPF updates for your *net-next* tree.
We've added 37 non-merge commits during the last 12 day(s) which contain
a total of 56 files changed, 394 insertions(+), 380 deletions(-).
The main changes are:
1) XDP driver RCU cleanups, from Toke Høiland-Jørgensen and Paul E. McKenney.
2) Fix bpf_skb_change_proto() IPv4/v6 GSO handling, from Maciej Żenczykowski.
3) Fix false positive kmemleak report for BPF ringbuf alloc, from Rustam Kovhaev.
4) Fix x86 JIT's extable offset calculation for PROBE_LDX NULL, from Ravi Bangoria.
5) Enable libbpf fallback probing with tracing under RHEL7, from Jonathan Edwards.
6) Clean up x86 JIT to remove unused cnt tracking from EMIT macro, from Jiri Olsa.
7) Netlink cleanups for libbpf to please Coverity, from Kumar Kartikeya Dwivedi.
8) Allow to retrieve ancestor cgroup id in tracing programs, from Namhyung Kim.
9) Fix lirc BPF program query to use user-provided prog_cnt, from Sean Young.
10) Add initial libbpf doc including generated kdoc for its API, from Grant Seltzer.
11) Make xdp_rxq_info_unreg_mem_model() more robust, from Jakub Kicinski.
12) Fix up bpfilter startup log-level to info level, from Gary Lin.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Call bnxt_ptp_init() to initialize and register with the clock driver
to enable PTP support. Call bnxt_ptp_free() to unregister and clean
up during shutdown.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Setup the TXBD to enable TX timestamp if requested. At TX packet DMA
completion, if we requested TX timestamp on that packet, we defer to
.do_aux_work() to obtain the TX timestamp from the firmware before we
free the TX SKB.
v2: Use .do_aux_work() to get the TX timestamp from firmware.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the RX packet is timestamped by the hardware, the RX completion
record will contain the lower 32-bit of the timestamp. This needs
to be combined with the upper 16-bit of the periodic timestamp that
we get from the timer. The previous snapshot in ptp->old_timer is
used to make sure that the snapshot is not ahead of the RX timestamp
and we adjust for wrap-around if needed.
v2: Make ptp->old_time read access safe on 32-bit CPUs.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
From the bnxt_timer(), read the 48-bit hardware running clock
periodically and store it in ptp->current_time. The previous snapshot
of the clock will be stored in ptp->old_time. The old_time snapshot
will be used in the next patches to compute the RX packet timestamps.
v2: Use .do_aux_work() to read the timer periodically.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the clock APIs to set/get/adjust the hw clock, and the related
ioctls and ethtool methods.
v2: Propagate error code from ptp_clock_register().
Add spinlock to serialize access to the timecounter. The
timecounter is accessed in process context and the RX datapath.
Read the PHC using direct registers.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Store PTP hardware info in a structure if hardware and firmware support PTP.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adding the PTP related firmware interface is the main change.
There is also a name change for admin_mtu, requiring code fixup.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Broadcom UniMAC MDIO bus from mdio-bcm-unimac module comes too late.
So, GENET cannot find the ethernet PHY on UniMAC MDIO bus. This leads
GENET fail to attach the PHY as following log:
bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
...
could not attach to PHY
bcmgenet fd580000.ethernet eth0: failed to connect to PHY
uart-pl011 fe201000.serial: no DMA platform data
libphy: bcmgenet MII bus: probed
...
unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
It is not just coming too late, there is also no way for the module
loader to figure out the dependency between GENET and its MDIO bus
driver unless we provide this MODULE_SOFTDEP hint.
This patch adds the soft dependency to load mdio-bcm-unimac module
before genet module to fix this issue.
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=213485
Fixes: 9a4e79697009 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The bnxt driver has rcu_read_lock()/rcu_read_unlock() pairs around XDP
program invocations. However, the actual lifetime of the objects referred
by the XDP program invocation is longer, all the way through to the call to
xdp_do_flush(), making the scope of the rcu_read_lock() too small. This
turns out to be harmless because it all happens in a single NAPI poll
cycle (and thus under local_bh_disable()), but it makes the rcu_read_lock()
misleading.
Rather than extend the scope of the rcu_read_lock(), just get rid of it
entirely. With the addition of RCU annotations to the XDP_REDIRECT map
types that take bh execution into account, lockdep even understands this to
be safe, so there's really no reason to keep it around.
Signed-off-by: Toke Høiland-Jørgensen <toke@redhat.com>
Signed-off-by: Daniel Borkmann <daniel@iogearbox.net>
Cc: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/bpf/20210624160609.292325-9-toke@redhat.com
|
|
The Broadcom UniMAC MDIO bus from mdio-bcm-unimac module comes too late.
So, GENET cannot find the ethernet PHY on UniMAC MDIO bus. This leads
GENET fail to attach the PHY as following log:
bcmgenet fd580000.ethernet: GENET 5.0 EPHY: 0x0000
...
could not attach to PHY
bcmgenet fd580000.ethernet eth0: failed to connect to PHY
uart-pl011 fe201000.serial: no DMA platform data
libphy: bcmgenet MII bus: probed
...
unimac-mdio unimac-mdio.-19: Broadcom UniMAC MDIO bus
This patch adds the soft dependency to load mdio-bcm-unimac module
before genet module to avoid the issue.
Fixes: 9a4e79697009 ("net: bcmgenet: utilize generic Broadcom UniMAC MDIO controller driver")
Buglink: https://bugzilla.kernel.org/show_bug.cgi?id=213485
Signed-off-by: Jian-Hong Pan <jhp@endlessos.org>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resetting software indexes in bcm4908_dma_alloc_buf_descs() is not
enough as it's called during device probe only. Driver resets DMA on
every .ndo_open callback and it's required to reset indexes then.
This fixes inconsistent rings state and stalled traffic after interface
down & up sequence.
Fixes: 4feffeadbcb2 ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial conflicts in net/can/isotp.c and
tools/testing/selftests/net/mptcp/mptcp_connect.sh
scaled_ppm_to_ppb() was moved from drivers/ptp/ptp_clock.c
to include/linux/ptp_clock_kernel.h in -next so re-apply
the fix there.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
bnxt_ethtool_init() may have allocated some memory and we need to
call bnxt_ethtool_free() to properly unwind if bnxt_init_one()
fails.
Fixes: 7c3809181468 ("bnxt_en: Refactor bnxt_init_one() and turn on TPA support on 57500 chips.")
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TQM fastpath ring needs to be sized to store both the requester
and responder side of RoCE QPs in TQM for supporting bi-directional
tests. Fix bnxt_alloc_ctx_mem() to multiply the RoCE QPs by a factor of
2 when computing the number of entries for TQM fastpath ring. This
fixes an RX pipeline stall issue when running bi-directional max
RoCE QP tests.
Fixes: c7dd7ab4b204 ("bnxt_en: Improve TQM ring context memory sizing formulas.")
Signed-off-by: Rukhsana Ansari <rukhsana.ansari@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a missing bnxt_probe_phy() call in bnxt_fw_init_one() to
rediscover the PHY capabilities after a firmware reset. This can cause
some PHY related functionalities to fail after a firmware reset. For
example, in multi-host, the ability for any host to configure the PHY
settings may be lost after a firmware reset.
Fixes: ec5d31e3c15d ("bnxt_en: Handle firmware reset status during IF_UP.")
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the devm_platform_ioremap_resource_byname() helper instead of
calling platform_get_resource_byname() and devm_ioremap_resource()
separately.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It will cause null-ptr-deref if platform_get_resource() returns NULL,
we need check the return value.
Signed-off-by: Yang Yingliang <yangyingliang@huawei.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Function 'bnx2x_vfpf_release' is declared twice, so remove the
repeated declaration.
Cc: Ariel Elior <aelior@marvell.com>
Cc: GR-everest-linux-l2@marvell.com
Signed-off-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Acked-by: Sudarsana Reddy Kalluru <skalluru@marvell.com>
Link: https://lore.kernel.org/r/1622449756-2627-1-git-send-email-zhangshaokun@hisilicon.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
cdc-wdm: s/kill_urbs/poison_urbs/ to fix build
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Eliminate the follow smatch warning:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sriov.c:1227
bnx2x_iov_init_one() warn: missing error code 'err'.
Reported-by: Abaci Robot <abaci@linux.alibaba.com>
Signed-off-by: Jiapeng Chong <jiapeng.chong@linux.alibaba.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There are a few leading spaces before tabs and remove it by running the
following commard:
$ find . -name '*.c' | xargs sed -r -i 's/^[ ]+\t/\t/'
$ find . -name '*.h' | xargs sed -r -i 's/^[ ]+\t/\t/'
Cc: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Hui Tang <tanghui20@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enable -Wimplicit-fallthrough for Clang, fix a warning
by explicitly adding a break statement instead of just letting the code
fall through to the next case.
Link: https://github.com/KSPP/linux/issues/115
Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c:13595: warning: expecting prototype for bnx2x_get_num_none_def_sbs(). Prototype was for bnx2x_get_num_non_def_sbs() instead
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c:4165: warning: expecting prototype for atomic_add_ifless(). Prototype was for __atomic_add_ifless() instead
drivers/net/ethernet/broadcom/bnx2x/bnx2x_sp.c:4193: warning: expecting prototype for atomic_dec_ifmoe(). Prototype was for __atomic_dec_ifmoe() instead
Cc: Ariel Elior <aelior@marvell.com>
Cc: Sudarsana Kalluru <skalluru@marvell.com>
Cc: GR-everest-linux-l2@marvell.com
Signed-off-by: Yang Shen <shenyang39@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
