| Age | Commit message (Collapse) | Author |
|---|
|
No driver registers for PCIE_PORT_SERVICE_VC, so remove it.
This removes the VC "service" files from /sys/bus/pci_express/devices,
e.g., 0000:07:00.0:pcie108, 0000:08:04.0:pcie208 (all the files that
contained "8" as the last digit of the "pcieXXX" part). The port driver
created these files for PCIe port devices that have a VC Capability.
Since this reduces PCIE_PORT_DEVICE_MAXSERVICES and moves DPC down into the
spot where VC used to be, the DPC sysfs files will now be named "pcieXX8".
I don't think there's anything useful userspace can do with those files, so
I hope nobody cares about these filenames.
There is no VC driver that calls pcie_port_service_register(), so there
never was a /sys/bus/pci_express/drivers/vc directory.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
The pcie_port_bus_type must be registered before drivers that depend on it
can be registered. Those drivers include:
pcied_init() # PCIe native hotplug driver
aer_service_init() # AER driver
dpc_service_init() # DPC driver
pcie_pme_service_init() # PME driver
Previously we registered pcie_port_bus_type from pcie_portdrv_init(), a
device_initcall. The callers of pcie_port_service_register() (above) are
also device_initcalls. This is fragile because the device_initcall
ordering depends on link order, which is not explicit.
Register pcie_port_bus_type from pci_driver_init() along with pci_bus_type.
This removes the link order dependency between portdrv and the pciehp, AER,
DPC, and PCIe PME drivers.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
The "pcie_ports=compat" kernel parameter sets pcie_ports_disabled, which is
intended to disable the PCIe port driver. But even when it was disabled,
we registered pcie_portdriver so we could work around a BIOS PME issue (see
fe31e69740ed ("PCI/PCIe: Clear Root PME Status bits early during system
resume")).
Registering the driver meant that the pcie_portdrv_probe() path called
pci_enable_device(), pci_save_state(), pm_runtime_set_autosuspend_delay(),
pm_runtime_use_autosuspend(), etc., even when the driver was disabled.
We've since moved the BIOS PME workaround from the port driver to the core,
so stop registering the PCIe port driver in compat mode.
This means "pcie_ports=compat" will now be basically the same as turning
off CONFIG_PCIEPORTBUS completely.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Per PCIe r4.0, sec 6.1.6, Root Complex Event Collectors can generate PME
interrupts on behalf of Root Complex Integrated Endpoints.
Linux does not currently enable PME interrupts from RC Event Collectors,
but fe31e69740ed ("PCI/PCIe: Clear Root PME Status bits early during system
resume") suggests PME interrupts may be enabled by the platform for ACPI-
based runtime wakeup.
Clear the PCIe PME Status bit for Root Complex Event Collectors during
resume, just like we already do for Root Ports.
If the BIOS enables PME interrupts for an event collector and neglects to
clear the status bit on resume, this change should fix the same bug as
fe31e69740ed (PMEs not working after waking from a sleep state), but for
Root Complex Integrated Endpoints.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Add pcie_bandwidth_capable() to compute the max link bandwidth supported by
a device, based on the max link speed and width, adjusted by the encoding
overhead.
The maximum bandwidth of the link is computed as:
max_link_width * max_link_speed * (1 - encoding_overhead)
2.5 and 5.0 GT/s links use 8b/10b encoding, which reduces the raw bandwidth
available by 20%; 8.0 GT/s and faster links use 128b/130b encoding, which
reduces it by about 1.5%.
The result is in Mb/s, i.e., megabits/second, of raw bandwidth.
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: add 16 GT/s, adjust for pcie_get_speed_cap() and
pcie_get_width_cap() signatures, don't export outside drivers/pci]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Add pcie_get_width_cap() to find the max link width supported by a device.
Change max_link_width_show() to use pcie_get_width_cap().
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: return width directly instead of error and *width, don't export
outside drivers/pci]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
|
|
Add pcie_get_speed_cap() to find the max link speed supported by a device.
Change max_link_speed_show() to use pcie_get_speed_cap().
Signed-off-by: Tal Gilboa <talgi@mellanox.com>
[bhelgaas: return speed directly instead of error and *speed, don't export
outside drivers/pci]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Tariq Toukan <tariqt@mellanox.com>
|
|
Linux 4.16-rc7
This was requested by Daniel, and things were getting
a bit hard to reconcile, most of the conflicts were
trivial though.
|
|
Mike Lothian reported that plugging in a USB-C device does not work
properly in his Dell Alienware system. This system has an Intel Alpine
Ridge Thunderbolt controller providing USB-C functionality. In these
systems the USB controller (xHCI) is hotplugged whenever a device is
connected to the port using ACPI-based hotplug.
The ACPI description of the root port in question is as follows:
Device (RP01)
{
Name (_ADR, 0x001C0000)
Device (PXSX)
{
Name (_ADR, 0x02)
Method (_RMV, 0, NotSerialized)
{
// ...
}
}
Here _ADR 0x02 means device 0, function 2 on the bus under root port (RP01)
but that seems to be incorrect because device 0 is the upstream port of the
Alpine Ridge PCIe switch and it has no functions other than 0 (the bridge
itself). When we get ACPI Notify() to the root port resulting from
connecting a USB-C device, Linux tries to read PCI_VENDOR_ID from device 0,
function 2 which of course always returns 0xffffffff because there is no
such function and we never find the device.
In Windows this works fine.
Now, since we get ACPI Notify() to the root port and not to the PXSX device
we should actually start our scan from there as well and not from the
non-existent PXSX device. Fix this by checking presence of the slot itself
(function 0) if we fail to do that otherwise.
While there use pci_bus_read_dev_vendor_id() in get_slot_status(), which is
the recommended way to read Device and Vendor IDs of devices on PCI buses.
Link: https://bugzilla.kernel.org/show_bug.cgi?id=198557
Reported-by: Mike Lothian <mike@fireburn.co.uk>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: stable@vger.kernel.org
|
|
Compiling the xilinx-nwl driver with sparse checks result in the
following warning:
drivers/pci/host/pcie-xilinx-nwl.c:633:38: sparse: cast truncates bits
from constant value (ffffffff00000000 becomes 0)
Fix it by explicitly writing 0 to mask interrupts instead of relying
on a bogus cast applied to the mask bitwise complement.
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Cc: Bjorn Helgaas <bhelgaas@google.com>
Cc: Rob Herring <robh@kernel.org>
Cc: Michal Simek <michal.simek@xilinx.com>
|
|
drivers/pci/host/pci-v3-semi.c:676:2-3: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Julia Lawall <julia.lawall@lip6.fr>
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
This was generated from 0-day builder.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[lorenzo.pieralisi@arm.com: reworked/split patch]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This was generated from 0-day builder.
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
[robh: add commit msg]
Signed-off-by: Rob Herring <robh@kernel.org>
[lorenzo.pieralisi@arm.com: reworked the commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
PCIe 4.0 defines the 16.0 GT/s link speed. Links can run at that speed
without any Linux changes, but previously their sysfs "max_link_speed" and
"current_link_speed" files contained "Unknown speed", not the expected
"16.0 GT/s".
Add decoding for the new 16 GT/s link speed.
Signed-off-by: Jay Fang <f.fangjian@huawei.com>
[bhelgaas: add PCI_EXP_LNKCAP2_SLS_16_0GB]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Dongdong Liu <liudongdong3@huawei.com>
|
|
PCIE_DW_HOST depends on PCI_MSI_IRQ_DOMAIN and since kirin selects
PCIE_DW_HOST, it must also depend on PCI_MSI_IRQ_DOMAIN. This was found
by 0-day once building on all arches was enabled.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
The iproc driver is using ARM's struct pci_sys_data simply to store a
private data pointer. This is completely unnecessary, so store the
private data directly in bus->sysdata as is done on arm64.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Scott Branden <scott.branden@broadcom.com>
|
|
compiler.h is unnecessary and doesn't exist on some arches, so remove
it.
Signed-off-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata
Pull libata fixes from Tejun Heo:
"I sat on them too long and it's quite a few this late, but nothing has
a wide blast area. The changes are...
- Fix corner cases in SG command handling.
- Recent introduction of default powersaving mode config option
exposed several devices with broken powersaving behaviors. A number
of patches to update the blacklist accordingly.
- Fix a kernel panic on SAS hotplug.
- Other misc and device specific updates"
* 'for-4.16-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/tj/libata:
libata: Modify quirks for MX100 to limit NCQ_TRIM quirk to MU01 version
libata: Make Crucial BX100 500GB LPM quirk apply to all firmware versions
libata: Apply NOLPM quirk to Crucial M500 480 and 960GB SSDs
libata: Enable queued TRIM for Samsung SSD 860
PCI: Add function 1 DMA alias quirk for Highpoint RocketRAID 644L
ahci: Add PCI-id for the Highpoint Rocketraid 644L card
ata: do not schedule hot plug if it is a sas host
libata: disable LPM for Crucial BX100 SSD 500GB drive
libata: Apply NOLPM quirk to Crucial MX100 512GB SSDs
libata: update documentation for sysfs interfaces
ata: sata_rcar: Remove unused variable in sata_rcar_init_controller()
libata: transport: cleanup documentation of sysfs interface
sata_rcar: Reset SATA PHY when Salvator-X board resumes
libata: don't try to pass through NCQ commands to non-NCQ devices
libata: remove WARN() for DMA or PIO command without data
libata: fix length validation of ATAPI-relayed SCSI commands
ata: libahci: fix comment indentation
ahci: Add check for device presence (PCIe hot unplug) in ahci_stop_engine()
libata: Fix compile warning with ATA_DEBUG enabled
|
|
Per PCIe r4.0, sec 9.3.4.1.11, the BAR registers in VF config space are all
RO Zero, so skip sizing them.
This is an optimization when enabling SR-IOV on a device with many VFs.
Suggested-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: KarimAllah Ahmed <karahmed@amazon.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Remove pointless comments that tell us the file name, remove blank line
comments, follow multi-line comment conventions. No functional change
intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Indent things so they line up neatly and remove extra blank lines and
superfluous comments. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
With "initcall_debug", we report how long every PCI quirk took.
Even without "initcall_debug", report the runtime of any quirk that takes
longer than 10ms. This is to make it easier to notice quirks that slow
down boot.
This was motivated by a report from Paul Menzel that PCI final quirks took
half a second at boot.
Link: https://lkml.kernel.org/r/44cada166e42007d27b4c3e3aa0744d7@molgen.mpg.de
Reported-by: Paul Menzel <pmenzel@molgen.mpg.de>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
With "initcall_debug", we report how long every PCI quirk took. Previously
we used pr_debug(), which means you have to figure out how to enable debug
output.
Log these timings using pci_info() instead so it doesn't depend on DEBUG,
CONFIG_DYNAMIC_DEBUG, etc.
Also, don't log anything at all unless "initcall_debug" is specified. This
matches what we do in do_one_initcall_debug().
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
The VPD-related structures are only used in vpd.c, so move them from
drivers/pci/pci.h to vpd.c. No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Move the VPD-related quirks from quirks.c to vpd.c, which removes the need
for struct pci_vpd outside vpd.c. The goal is to encapsulate all the VPD
code and structures in vpd.c.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Move the VPD-related sysfs code from pci-sysfs.c to vpd.c. This follows
the pattern of pcie_aspm_create_sysfs_dev_files(). The goal is to
encapsulate all the VPD code and structures in vpd.c.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Move the VPD-related code from access.c to vpd.c. The goal is to
encapsulate all the VPD code and structures in vpd.c.
No functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Tegra186 powergate driver is implemented as power domain driver, power
partition ungate/gate are registered as power_on/power_off callback
functions. There are no direct functions to power gate/ungate host
controller in Tegra186. Host controller driver should add "power-domains"
property in device tree and implement runtime suspend and resume
callback functons. Power gate and ungate is taken care by power domain
driver when host controller driver calls pm_runtime_put_sync and
pm_runtime_get_sync respectively.
Register suspend_noirq & resume_noirq callback functions to allow PCIe to
come up after resume from RAM. Both runtime and noirq pm ops share same
callback functions.
Signed-off-by: Manikanta Maddireddy <mmaddireddy@nvidia.com>
[lorenzo.pieralisi@arm.com: squashed patch to fix compilation]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
Tested-by: Thierry Reding <treding@nvidia.com>
|
|
If there is pending work in hv_pci_devices_present() we just need to add
the new dr entry into the dr_list. Add a check to detect pending work
items and update the code to skip queuing work if pending work items
are detected.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Jack Morgenstein <jackm@mellanox.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
|
|
When kernel is executing hv_eject_device_work(), hpdev->state value must
be hv_pcichild_ejecting; any other value would consist in a bug,
therefore replace the bogus check with an explicit WARN_ON() on the
condition failure detection.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: updated commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Jack Morgenstein <jackm@mellanox.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
|
|
Comment in _hv_pcifront_read_config() contains a typo, fix it.
No functional change.
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: changed commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
|
|
1. With the patch "x86/vector/msi: Switch to global reservation mode",
the recent v4.15 and newer kernels always hang for 1-vCPU Hyper-V VM
with SR-IOV. This is because when we reach hv_compose_msi_msg() by
request_irq() -> request_threaded_irq() ->__setup_irq()->irq_startup()
-> __irq_startup() -> irq_domain_activate_irq() -> ... ->
msi_domain_activate() -> ... -> hv_compose_msi_msg(), local irq is
disabled in __setup_irq().
Note: when we reach hv_compose_msi_msg() by another code path:
pci_enable_msix_range() -> ... -> irq_domain_activate_irq() -> ... ->
hv_compose_msi_msg(), local irq is not disabled.
hv_compose_msi_msg() depends on an interrupt from the host.
With interrupts disabled, a UP VM always hangs in the busy loop in
the function, because the interrupt callback hv_pci_onchannelcallback()
can not be called.
We can do nothing but work it around by polling the channel. This
is ugly, but we don't have any other choice.
2. If the host is ejecting the VF device before we reach
hv_compose_msi_msg(), in a UP VM, we can hang in hv_compose_msi_msg()
forever, because at this time the host doesn't respond to the
CREATE_INTERRUPT request. This issue exists the first day the
pci-hyperv driver appears in the kernel.
Luckily, this can also by worked around by polling the channel
for the PCI_EJECT message and hpdev->state, and by checking the
PCI vendor ID.
Note: actually the above 2 issues also happen to a SMP VM, if
"hbus->hdev->channel->target_cpu == smp_processor_id()" is true.
Fixes: 4900be83602b ("x86/vector/msi: Switch to global reservation mode")
Tested-by: Adrian Suhov <v-adsuho@microsoft.com>
Tested-by: Chris Valean <v-chvale@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: <stable@vger.kernel.org>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Jack Morgenstein <jackm@mellanox.com>
|
|
When we hot-remove the device, we first receive a PCI_EJECT message and
then receive a PCI_BUS_RELATIONS message with bus_rel->device_count == 0.
The first message is offloaded to hv_eject_device_work(), and the second
is offloaded to pci_devices_present_work(). Both the paths can be running
list_del(&hpdev->list_entry), causing general protection fault, because
system_wq can run them concurrently.
The patch eliminates the race condition.
Since access to present/eject work items is serialized, we do not need the
hbus->enum_sem anymore, so remove it.
Fixes: 4daace0d8ce8 ("PCI: hv: Add paravirtual PCI front-end for Microsoft Hyper-V VMs")
Link: https://lkml.kernel.org/r/KL1P15301MB00064DA6B4D221123B5241CFBFD70@KL1P15301MB0006.APCP153.PROD.OUTLOOK.COM
Tested-by: Adrian Suhov <v-adsuho@microsoft.com>
Tested-by: Chris Valean <v-chvale@microsoft.com>
Signed-off-by: Dexuan Cui <decui@microsoft.com>
[lorenzo.pieralisi@arm.com: squashed semaphore removal patch]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Reviewed-by: Michael Kelley <mikelley@microsoft.com>
Acked-by: Haiyang Zhang <haiyangz@microsoft.com>
Cc: <stable@vger.kernel.org> # v4.6+
Cc: Vitaly Kuznetsov <vkuznets@redhat.com>
Cc: Jack Morgenstein <jackm@mellanox.com>
Cc: Stephen Hemminger <sthemmin@microsoft.com>
Cc: K. Y. Srinivasan <kys@microsoft.com>
|
|
The Tile architecture port was added by Chris Metcalf in 2010, and
maintained until early 2018 when he orphaned it due to his departure
from Mellanox, and nobody else stepped up to maintain it. The product
line is still around in the form of the BlueField SoC, but no longer
uses the Tile architecture.
There are also still products for sale with Tile-GX SoCs, notably the
Mikrotik CCR router family. The products all use old (linux-3.3) kernels
with lots of patches and won't be upgraded by their manufacturers. There
have been efforts to port both OpenWRT and Debian to these, but both
projects have stalled and are very unlikely to be continued in the future.
Given that we are reasonably sure that nobody is still using the port
with an upstream kernel any more, it seems better to remove it now while
the port is in a good shape than to let it bitrot for a few years first.
Cc: Chris Metcalf <chris.d.metcalf@gmail.com>
Cc: John Paul Adrian Glaubitz <glaubitz@physik.fu-berlin.de>
Link: http://www.mellanox.com/page/npu_multicore_overview
Link: https://jenkins.debian.net/view/rebootstrap/job/rebootstrap_tilegx_gcc7/
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Building the tegra PCIe host driver without MSI results in a link
failure:
drivers/pci/host/pci-tegra.o:(.data+0x70): undefined reference to
`pci_msi_unmask_irq'
drivers/pci/host/pci-tegra.o:(.data+0x74): undefined reference to
`pci_msi_mask_irq'
This adds the same dependency that everyone else uses.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[lorenzo.pieralisi@arm.com: rewrote commit log]
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Thierry Reding <treding@nvidia.com>
|
|
Back in 2013, runtime PM for GPUs with integrated HDA controller was
introduced with commits 0d69704ae348 ("gpu/vga_switcheroo: add driver
control power feature. (v3)") and 246efa4a072f ("snd/hda: add runtime
suspend/resume on optimus support (v4)").
Briefly, the idea was that the HDA controller is forced on and off in
unison with the GPU.
The original code is mostly still in place even though it was never a
100% perfect solution: E.g. on access to the HDA controller, the GPU
is powered up via vga_switcheroo_runtime_resume_hdmi_audio() but there
are no provisions to keep it resumed until access to the HDA controller
has ceased: The GPU autosuspends after 5 seconds, rendering the HDA
controller inaccessible.
Additionally, a kludge is required when hda_intel.c probes: It has to
check whether the GPU is powered down (check_hdmi_disabled()) and defer
probing if so.
However in the meantime (in v4.10) the driver core has gained a feature
called device links which promises to solve such issues in a clean way:
It allows us to declare a dependency from the HDA controller (consumer)
to the GPU (supplier). The PM core then automagically ensures that the
GPU is runtime resumed as long as the HDA controller's ->probe hook is
executed and whenever the HDA controller is accessed.
By default, the HDA controller has a dependency on its parent, a PCIe
Root Port. Adding a device link creates another dependency on its
sibling:
PCIe Root Port
^ ^
| |
| |
HDA ===> GPU
The device link is not only used for runtime PM, it also guarantees that
on system sleep, the HDA controller suspends before the GPU and resumes
after the GPU, and on system shutdown the HDA controller's ->shutdown
hook is executed before the one of the GPU. It is a complete solution.
Using this functionality is as simple as calling device_link_add(),
which results in a dmesg entry like this:
pci 0000:01:00.1: Linked as a consumer to 0000:01:00.0
The code for the GPU-governed audio power management can thus be removed
(except where it's still needed for legacy manual power control).
The device link is added in a PCI quirk rather than in hda_intel.c.
It is therefore legal for the GPU to runtime suspend to D3cold even if
the HDA controller is not bound to a driver or if CONFIG_SND_HDA_INTEL
is not enabled, for accesses to the HDA controller will cause the GPU to
wake up regardless if they're occurring outside of hda_intel.c (think
config space readout via sysfs).
Contrary to the previous implementation, the HDA controller's power
state is now self-governed, rather than GPU-governed, whereas the GPU's
power state is no longer fully self-governed. (The HDA controller needs
to runtime suspend before the GPU can.)
It is thus crucial that runtime PM is always activated on the HDA
controller even if CONFIG_SND_HDA_POWER_SAVE_DEFAULT is set to 0 (which
is the default), lest the GPU stays awake. This is achieved by setting
the auto_runtime_pm flag on every codec and the AZX_DCAPS_PM_RUNTIME
flag on the HDA controller.
A side effect is that power consumption might be reduced if the GPU is
in use but the HDA controller is not, because the HDA controller is now
allowed to go to D3hot. Before, it was forced to stay in D0 as long as
the GPU was in use. (There is no reduction in power consumption on my
Nvidia GK107, but there might be on other chips.)
The code paths for legacy manual power control are adjusted such that
runtime PM is disabled during power off, thereby preventing the PM core
from resuming the HDA controller.
Note that the device link is not only added on vga_switcheroo capable
systems, but for *any* GPU with integrated HDA controller. The idea is
that the HDA controller streams audio via connectors located on the GPU,
so the GPU needs to be on for the HDA controller to do anything useful.
This commit implicitly fixes an unbalanced runtime PM ref upon unbind of
hda_intel.c: On ->probe, a runtime PM ref was previously released under
the condition "azx_has_pm_runtime(chip) || hda->use_vga_switcheroo", but
on ->remove a runtime PM ref was only acquired under the first of those
conditions. Thus, binding and unbinding the driver twice on a
vga_switcheroo capable system caused the runtime PM refcount to drop
below zero. The issue is resolved because the AZX_DCAPS_PM_RUNTIME flag
is now always set if use_vga_switcheroo is true.
For more information on device links please refer to:
https://www.kernel.org/doc/html/latest/driver-api/device_link.html
Documentation/driver-api/device_link.rst
Cc: Dave Airlie <airlied@redhat.com>
Cc: Ben Skeggs <bskeggs@redhat.com>
Cc: Alex Deucher <alexander.deucher@amd.com>
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Peter Wu <peter@lekensteyn.nl>
Tested-by: Kai Heng Feng <kai.heng.feng@canonical.com> # AMD PowerXpress
Tested-by: Mike Lothian <mike@fireburn.co.uk> # AMD PowerXpress
Tested-by: Denis Lisov <dennis.lissov@gmail.com> # Nvidia Optimus
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/51bd38360ff502a8c42b1ebf4405ee1d3f27118d.1520068884.git.lukas@wunner.de
|
|
There are PCI devices which are power-manageable by a nonstandard means,
such as a custom ACPI method. One example are discrete GPUs in hybrid
graphics laptops, another are Thunderbolt controllers in Macs.
Such devices can't be put into D3cold with pci_set_power_state() because
pci_platform_power_transition() fails with -ENODEV. Instead they're put
into D3hot by pci_set_power_state() and subsequently into D3cold by
invoking the nonstandard means. However as a consequence the cached
current_state is incorrectly left at D3hot.
What we need to do is walk the hierarchy below such a PCI device on
powerdown and update the current_state to D3cold. On powerup the PCI
device itself and the hierarchy below it is in D0uninitialized, so we
need to walk the hierarchy again and wake all devices, causing them to
be put into D0active and then letting them autosuspend as they see fit.
To this end make pci_wakeup_bus() & pci_bus_set_current_state() public
so PCI drivers don't have to reinvent the wheel.
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/2962443259e7faec577274b4ef8c54aad66f9a94.1520068884.git.lukas@wunner.de
|
|
We leave PCI devices not bound to a driver in D0 during runtime suspend.
But they may have a parent which is bound and can be transitioned to
D3cold at runtime. Once the parent goes to D3cold, the unbound child
may go to D3cold as well. When the child goes to D3cold, its internal
state, including configuration of BARs, MSI, ASPM, MPS, etc., is lost.
One example are recent hybrid graphics laptops which cut power to the
discrete GPU when the root port above it goes to ACPI power state D3.
Users may provoke this by unbinding the GPU driver and allowing runtime
PM on the GPU via sysfs: The PM core will then treat the GPU as
"suspended", which in turn allows the root port to runtime suspend,
causing the power resources listed in its _PR3 object to be powered off.
The GPU's BARs will be uninitialized when a driver later probes it.
Another example are hybrid graphics laptops where the GPU itself (rather
than the root port) is capable of runtime suspending to D3cold. If the
GPU's integrated HDA controller is not bound and the GPU's driver
decides to runtime suspend to D3cold, the HDA controller's BARs will be
uninitialized when a driver later probes it.
Fix by saving and restoring config space over a runtime suspend cycle
even if the device is not bound.
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Tested-by: Peter Wu <peter@lekensteyn.nl> # Nvidia Optimus
Tested-by: Lukas Wunner <lukas@wunner.de> # MacBook Pro
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
[lukas: add commit message, bikeshed code comments for clarity]
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://patchwork.freedesktop.org/patch/msgid/92fb6e6ae2730915eb733c08e2f76c6a313e3860.1520068884.git.lukas@wunner.de
|
|
In pnv_php_unregister_one(), pnv_php_put_slot() might kfree
php_slot structure. But there is pci_hp_deregister() after
that with php_slot reference.
This patch moves pnv_php_put_slot() to the end of function.
Signed-off-by: Simon Guo <wei.guo.simon@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
fe31e69740ed ("PCI/PCIe: Clear Root PME Status bits early during system
resume") added a .resume_noirq() callback to the PCIe port driver to clear
the PME Status bit during resume to work around a BIOS issue.
The BIOS evidently enabled PME interrupts for ACPI-based runtime wakeups
but did not clear the PME Status bit during resume, which meant PMEs after
resume did not trigger interrupts because PME Status did not transition
from cleared to set.
The fix was in the PCIe port driver, so it worked when CONFIG_PCIEPORTBUS
was set. But I think we *always* want the fix because the platform may use
PME interrupts even if Linux is built without the PCIe port driver.
Move the fix from the port driver to the PCI core so we can work around
this "PME doesn't work after waking from a sleep state" issue regardless of
CONFIG_PCIEPORTBUS.
[bhelgaas: folded in warning fix from Arnd Bergmann <arnd@arndb.de>:
https://lkml.kernel.org/r/20180328134747.2062348-1-arnd@arndb.de]
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
|
|
Move pcie_clear_root_pme_status() from the port driver to the PCI core so
it will be available even when the port driver isn't present. No
functional change intended.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI fixes from Bjorn Helgaas:
- fix sparc build issue when OF_IRQ not enabled (Guenter Roeck)
- fix enumeration of devices below switches on DesignWare-based
controllers (Koen Vandeputte)
* tag 'pci-v4.16-fixes-3' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci:
PCI: dwc: Fix enumeration end when reaching root subordinate
PCI: Move of_irq_parse_and_map_pci() declaration under OF_IRQ
|
|
pcieport_if.h contained the interfaces to register port service driver,
e.g., pcie_port_service_register(). portdrv.h contained internal data
structures of the port driver.
I don't think it's worth keeping those files separate, since both headers
and their users are all inside the PCI core.
Merge pcieport_if.h directly in drivers/pci/pcie/portdrv.h and update the
users to include that instead.
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
|
|
Per PCIe r4.0, sec 7.5.1.1.9, multi-function devices are required to have a
function 0. Therefore, Linux scans for devices at function 0 (devfn
0/8/16/...) and only scans for other functions if function 0 has its
Multi-Function Device bit set or ARI or SR-IOV indicate there are more
functions.
The Jailhouse hypervisor may pass individual functions of a multi-function
device to a guest without passing function 0, which means a Linux guest
won't find them.
Change Linux PCI probing so it scans all function numbers when running as a
guest over Jailhouse.
This is technically prohibited by the spec, so it is possible that PCI
devices without the Multi-Function Device bit set may have unexpected
behavior in response to this probe.
Originally-by: Benedikt Spranger <b.spranger@linutronix.de>
Signed-off-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Bjorn Helgaas <bhelgaas@google.com>
Cc: jailhouse-dev@googlegroups.com
Cc: Benedikt Spranger <b.spranger@linutronix.de>
Cc: linux-pci@vger.kernel.org
Cc: virtualization@lists.linux-foundation.org
Link: https://lkml.kernel.org/r/06e279b2a3e06cf6689ab3975f8ab592bba02362.1520408357.git.jan.kiszka@siemens.com
|
|
The subordinate value indicates the highest bus number which can be
reached downstream though a certain device.
Commit a20c7f36bd3d ("PCI: Do not allocate more buses than available in
parent") ensures that downstream devices cannot assign busnumbers higher
than the upstream device subordinate number, which was indeed illogical.
By default, dw_pcie_setup_rc() inits the Root Complex subordinate to a
value of 0x01.
Due to this combined with above commit, enumeration stops digging deeper
downstream as soon as bus num 0x01 has been assigned, which is always the
case for a bridge device.
This results in all devices behind a bridge bus remaining undetected, as
these would be connected to bus 0x02 or higher.
Fix this by initializing the RC to a subordinate value of 0xff, which is
not altering hardware behaviour in any way, but informs probing function
pci_scan_bridge() later on which reads this value back from register.
The following nasty errors during boot are also fixed by this:
pci_bus 0000:02: busn_res: can not insert [bus 02-ff] under [bus 01] (conflicts with (null) [bus 01])
...
pci_bus 0000:03: [bus 03] partially hidden behind bridge 0000:01 [bus 01]
...
pci_bus 0000:04: [bus 04] partially hidden behind bridge 0000:01 [bus 01]
...
pci_bus 0000:05: [bus 05] partially hidden behind bridge 0000:01 [bus 01]
pci_bus 0000:02: busn_res: [bus 02-ff] end is updated to 05
pci_bus 0000:02: busn_res: can not insert [bus 02-05] under [bus 01] (conflicts with (null) [bus 01])
pci_bus 0000:02: [bus 02-05] partially hidden behind bridge 0000:01 [bus 01]
Fixes: a20c7f36bd3d ("PCI: Do not allocate more buses than available in
parent")
Tested-by: Niklas Cassel <niklas.cassel@axis.com>
Tested-by: Fabio Estevam <fabio.estevam@nxp.com>
Tested-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Acked-by: Lucas Stach <l.stach@pengutronix.de>
Cc: stable@vger.kernel.org # v4.15+
Cc: Binghui Wang <wangbinghui@hisilicon.com>
Cc: Jesper Nilsson <jesper.nilsson@axis.com>
Cc: Jianguo Sun <sunjianguo1@huawei.com>
Cc: Jingoo Han <jingoohan1@gmail.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Cc: Lucas Stach <l.stach@pengutronix.de>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Minghuan Lian <minghuan.Lian@freescale.com>
Cc: Mingkai Hu <mingkai.hu@freescale.com>
Cc: Murali Karicheri <m-karicheri2@ti.com>
Cc: Pratyush Anand <pratyush.anand@gmail.com>
Cc: Richard Zhu <hongxing.zhu@nxp.com>
Cc: Roy Zang <tie-fei.zang@freescale.com>
Cc: Shawn Guo <shawn.guo@linaro.org>
Cc: Stanimir Varbanov <svarbanov@mm-sol.com>
Cc: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Cc: Xiaowei Song <songxiaowei@hisilicon.com>
Cc: Zhou Wang <wangzhou1@hisilicon.com>
|
|
The power supplies to PCIe port are often controlled by GPIO on some board
designs. Let's add an optional regulator which can be backed by GPIO to
control the power.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Rob Herring <robh@kernel.org>
|
|
If clk_prepare_enable() call fails on a particular clock, we should not
call clk_disable_unprepare() on this clock, but on the clocks that
succeed from clk_prepare_enable() previously.
Signed-off-by: Shawn Guo <shawn.guo@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
|
|
This patch converts existing regulators to use regulator bulk apis,
to make it consistent with msm8996 changes also cut down some redundant code.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
|
|
This patch adds supplies that are required for msm8996. vdda
is analog supply that go in to controller, and vddpe_3v3 is
supply to PCIe endpoint.
Without these supplies PCIe endpoints which require power supplies are
not enumerated at all, as there is no one to power it up.
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Lorenzo Pieralisi <lorenzo.pieralisi@arm.com>
Acked-by: Stanimir Varbanov <svarbanov@mm-sol.com>
Reviewed-by: Rob Herring <robh@kernel.org>
|
