| Age | Commit message (Collapse) | Author |
|---|
|
The earlycon depends on the bootloader setup UART clocks being retained.
There're actually two uart clocks (ipg, per) on MX6QDL,
but the 'Fixes' commit change to register only one which means
another clock may be disabled during booting phase
and result in the earlycon unwork.
Cc: stable@vger.kernel.org # v5.10+
Fixes: 379c9a24cc23 ("clk: imx: Fix reparenting of UARTs not associated with stdout")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20210702085438.1988087-1-aisheng.dong@nxp.com
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Remove the PLL clock gates as the allowing to gate the sys1_pll_266m breaks
the uSDHC module which is sporadically unable to enumerate devices after
this change. Also it makes AMP clock management harder with no obvious
benefit to Linux, so just revert the change.
Link: https://lore.kernel.org/r/20210528180135.1640876-1-l.stach@pengutronix.de
Fixes: b04383b6a558 ("clk: imx8mq: Define gates for pll1/2 fixed dividers")
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
Since CPU clocks are managed by CPUFREQ and ATF, do not enable
runtime PM otherwise rpm gets out of status as cpufreq
also manages clock states.
Signed-off-by: Nitin Garg <nitin.garg@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
Add clock parent save and restore.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
Display sub-system has special clock settings in SCFW, the
bypassed clock is used instead of PLL in Linux kernel clock
tree, so when saving clock rate, need to save non-cached clock
rate for Display sub-system's bypass clocks, and other clocks
still use the cached clock rate which is with runtime PM ON.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
Add A72 clock to support cpufreq on A72 cluster.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
Add i.MX8QM cpufreq support for A53 cluster.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
PI PLL does not support enable/disable. So bypass it's
enable status restore.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
detach pd if can't power up as it may be allocated to a differet
partition.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
CPU clock is managed by ATF. No need save and restore.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
Because digital pll for parallel interface is on by default, and
not provide enable/disable function by scu, so add the related ops
for this kind of clocks.
Signed-off-by: Guoniu.zhou <guoniu.zhou@nxp.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
Add more scu clocks used by i.MX8 platforms.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
enet tx clk actually is sourced from a gpr divider, not default enet
clk. Add enet grp clocks for user to use correctly.
Cc: Abel Vesa <abel.vesa@nxp.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
Add imx8qm clock valid resource checking mechanism
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
clk-imx8qxp is a common SCU clock driver used by both QM and QXP
platforms. The clock numbers vary a bit between those two platforms.
This patch introduces a mechanism to only register the valid clocks
for one platform by checking the clk resource id table.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
SCU clock protocol supports a few clocks based on GPR controller
registers including mux/divider/gate.
Add a generic clock register API to support them all.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
Legacy scu clock binding are not maintained anymore, it has a very
limited clocks supported during initial upstreaming and obviously
unusable by products. So it's meaningless to keep it in
kernel which worse the code readability.
Remove it to keep code much cleaner.
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
There is no audio ipg clock on i.MX8MP, so remove this from
the clock driver.
Signed-off-by: Jacky Bai <ping.bai@nxp.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
When register failed, clk will be freed, it will generate dangling pointer
problem in later reference. it should return directly.
Signed-off-by: Jian Dong <dongjian@yulong.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
- The sys2_pll_50m should be one of the clock sels of PCIE_AUX clock.
Change the sys2_pll_500m to sys2_pll_50m.
- Correct one misspell of the imx8mq_pcie1_ctrl_sels definition, from
"sys2_pll_250m" to "sys2_pll_333m".
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
In the i.MX8MP PCIe design, the PCIe PHY REF clock comes from external
OSC or internal system PLL. It is configured in the IOMUX_GPR14 register
directly, and can't be contolled by CCM at all.
Remove the PCIE PHY clock from clock driver to clean up codes.
There is only one PCIe in i.MX8MP, remove the none exist second PCIe
related clocks.
Remove the none exsits clocks IDs together.
Signed-off-by: Richard Zhu <hongxing.zhu@nxp.com>
Reviewed-by: Jason Liu <jason.hui.liu@nxp.com>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
Most if not all i.MX SoC's call a function which enables all UARTS.
This is a problem for users who need to re-parent the clock source,
because any attempt to change the parent results in an busy error
due to the fact that the clocks have been enabled already.
clk: failed to reparent uart1 to sys_pll1_80m: -16
Instead of pre-initializing all UARTS, scan the device tree to see
which UART clocks are associated to stdout, and only enable those
UART clocks if it's needed early. This will move initialization of
the remaining clocks until after the parenting of the clocks.
When the clocks are shutdown, this mechanism will also disable any
clocks that were pre-initialized.
Fixes: 9461f7b33d11c ("clk: fix CLK_SET_RATE_GATE with clock rate protection")
Suggested-by: Aisheng Dong <aisheng.dong@nxp.com>
Signed-off-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Tested-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This is all driver updates, the majority of which is a bunch of new
Qualcomm clk drivers that dominate the diffstat because we add support
for six SoCs from that particular vendor.
The other big change is the removal of various clk drivers that are no
longer used now that the kernel is dropping support for those SoCs.
Beyond that there's the usual non-critical fixes for existing drivers
and a good number of patches from Lee Jones that cleanup a bunch of
W=1 enabled builds.
Removed Drivers:
- Remove efm32 clk driver
- Remove tango4 clk driver
- Remove zte zx clk driver
- Remove sirf prima2/atlast clk drivers
- Remove u300 clk driver
New Drivers:
- PLL support on MStar/SigmaStar ARMv7 SoCs
- CPU clks for Qualcomm SDX55
- GCC and RPMh clks for Qualcomm SC8180x and SC7280 SoCs
- GCC clks for Qualcomm SM8350
- GPU clks for Qualcomm SDM660/SDM630
Updates:
- Video clk fixups on Qualcomm SM8250
- Improvements for multimedia clks on Qualcomm MSM8998
- Fix many warnings with W=1 enabled builds under drivers/clk/
- Support crystal load capacitance for Versaclock VC5
- Add a "skip recall" DT binding for Silicon Labs' si570 to avoid
glitches at boot
- Convert Xilinx VCU clk driver to a proper clk provider driver
- Expose Xilinx ZynqMP clk driver to more platforms
- Amlogic pll driver fixup
- Amlogic meson8b clock controller dt support clean up
- Remove mipi clk from the Amlogic axg clock controller
- New Rockchip rk3368 clock ids related to camera input
- Use pr_notice() instead of pr_warn() on i.MX6Q pre-boot ldb_di_clk
reparenting
- A series from Liu Ying that adds some SCU clocks support for
i.MX8qxp DC0/MIPI-LVDS subsystems
- A series from Lucas Stach that adds PLL monitor clocks for i.MX8MQ,
and clkout1/2 support for i.MX8MM/MN
- Add I2c and Ethernet (RAVB) clocks on Renesas R-Car V3U
- Add timer (TMU) clocks on most Renesas R-Car Gen3 SoCs
- Add video-related (FCPVD/VSPD/VSPX), watchdog (RWDT), serial
(HSCIF), pincontrol/GPIO (PFC/GPIO), SPI (MSIOF), SDHI, and DMA
(SYS-DMAC) clocks on Renesas R-Car V3U
- Add support for the USB 2.0 clock selector on Renesas RZ/G2 SoCs
- Allwinner H616 SoC clk support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (171 commits)
clk: mstar: msc313-mpll: Fix format specifier
clk: mstar: Allow MStar clk drivers to be compile tested
clk: qoriq: use macros to generate pll_mask
clk: qcom: Add Global Clock controller (GCC) driver for SC7280
dt-bindings: clock: Add SC7280 GCC clock binding
clk: qcom: rpmh: Add support for RPMH clocks on SC7280
dt-bindings: clock: Add RPMHCC bindings for SC7280
clk: qcom: gcc-sm8350: add gdsc
dt-bindings: clock: Add QCOM SDM630 and SDM660 graphics clock bindings
clk: qcom: Add SDM660 GPU Clock Controller (GPUCC) driver
clk: qcom: mmcc-msm8996: Migrate gfx3d clock to clk_rcg2_gfx3d
clk: qcom: rcg2: Stop hardcoding gfx3d pingpong parent numbers
dt-bindings: clock: Add support for the SDM630 and SDM660 mmcc
clk: qcom: Add SDM660 Multimedia Clock Controller (MMCC) driver
clk: qcom: gcc-sdm660: Mark GPU CFG AHB clock as critical
clk: qcom: gcc-sdm660: Mark MMSS NoC CFG AHB clock as critical
clk: qcom: gpucc-msm8998: Allow fabia gpupll0 rate setting
clk: qcom: gpucc-msm8998: Add resets, cxc, fix flags on gpu_gx_gdsc
clk: qcom: gdsc: Implement NO_RET_PERIPH flag
clk: mstar: MStar/SigmaStar MPLL driver
...
|
|
Fixes the following W=1 kernel build warning(s):
drivers/clk/imx/clk-imx6sl.c:156:6: warning: no previous prototype for ‘imx6sl_set_wait_clk’ [-Wmissing-prototypes]
Cc: Russell King <linux@armlinux.org.uk>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Ahmad Fatoum <a.fatoum@pengutronix.de>
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
clkout1 and clkout2 allow to supply clocks from the SoC to the board,
which is used by some board designs to provide reference clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
clkout1 and clkout2 allow to supply clocks from the SoC to the board,
which is used by some board designs to provide reference clocks.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The PLL monitor is mentioned as a debug feature in the reference manual,
but there are some boards that use this clock output as a reference clock
for board level components. Add support for those clocks in the clock
driver, so this clock output can be used properly.
Note that the VIDEO1, GPU and VPU mux inputs are rotated compared to the
description in the reference manual. The order in this patch has been
empirically validated.
Signed-off-by: Lucas Stach <l.stach@pengutronix.de>
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fixes the following W=1 kernel build warning(s):
drivers/clk/imx/clk-imx31.c:54:28: warning: ‘uart_clks’ defined but not used [-Wunused-const-variable=]
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: linux-clk@vger.kernel.org
Cc: linux-arm-kernel@lists.infradead.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Since 5d283b083800 ("clk: imx6: Fix procedure to switch the parent
of LDB_DI_CLK"), the clock driver warns if ldb_di\d_sel is changed
from reset value on system boot. This warning is printed even if
the bootloader (or a previous kernel that did kexec) followed the
correct procedure for glitch-free reparenting.
As such systems are doing everything correctly, a warning is too
harsh. Demote to a notice, so users are still alerted, but without
cluttering a loglevel=5 boot.
While at it, add the words "possible glitch" into the log message, to
make it more user-friendly.
Signed-off-by: Ahmad Fatoum <a.fatoum@pengutronix.de>
Reviewed-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
A previous patch introduced a harmless randconfig warning:
WARNING: unmet direct dependencies detected for MXC_CLK_SCU
Depends on [n]: COMMON_CLK [=y] && ARCH_MXC [=n] && IMX_SCU [=y] && HAVE_ARM_SMCCC [=y]
Selected by [m]:
- CLK_IMX8QXP [=m] && COMMON_CLK [=y] && (ARCH_MXC [=n] && ARM64 [=y] || COMPILE_TEST [=y]) && IMX_SCU [=y] && HAVE_ARM_SMCCC [=y]
Since the symbol is now hidden and only selected by other symbols,
just remove the dependencies and require the other drivers to
get it right.
Fixes: 6247e31b7530 ("clk: imx: scu: fix MXC_CLK_SCU module build break")
Reported-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Link: https://lore.kernel.org/r/20201230155244.981757-1-arnd@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
This patch adds some SCU clocks support for i.MX8qxp MIPI-LVDS subsystems.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch corrects display clocks for i.MX8qxp DC0 subsystem by
calling imx_clk_scu2() to register them, instead of calling
imx_clk_scu(). The reason is that the clocks can source from
various parents. The clock source selection is controlled by
Distributed Slave System Controller(DSC). According to the DSC spec,
the below table describes the generic source selections for clocks
with the same type in various subsystems. And, the display controller
subsystem spec says the display clocks can source from PLL1, PLL2 or
bypass clock, thus we may specify the correct parents for imx_clk_scu2().
The bypass clock's parent is determined by the SCU firmware.
Currently, the parent is 'pixel_link_clk_in' from HW point of view.
To be more specific, the parent is dummy for i.MX8qxp DC0, while
HDMI TX PHY PLL for i.MX8qm DC0. In practice, the display clocks
source from the bypass clock only when driving i.MX8qm HDMI TX.
So, for the both display clocks, we simply specify 'dc0_bypass0_clk'
bypass clock as a valid parent.
-----------------------------------------
| src_sel[28:26] | |
-----------------------------------------
| 0x0 | xtal24M |
| 0x1 | PLL0 |
| 0x2 | PLL1 |
| 0x3 | PLL2 |
| 0x4 | bypass reference clock |
| 0x5 to 0x7 | reserved |
-----------------------------------------
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds SCU clocks support for i.MX8qxp DC0 subsystem bypass clocks.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Cc: Rob Herring <robh+dt@kernel.org>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds SCU clocks support for i.MX8qxp DC0 subsystem PLL clocks.
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Stephen Boyd <sboyd@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Liu Ying <victor.liu@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"The core framework got some nice improvements this time around. We
gained the ability to get struct clk pointers from a struct clk_hw so
that clk providers can consume the clks they provide, if they need to
do something like that. This has been a long missing part of the clk
provider API that will help us move away from exposing a struct clk
pointer in the struct clk_hw. Tracepoints are added for the
clk_set_rate() "range" functions, similar to the tracepoints we
already have for clk_set_rate() and we added a column to debugfs to
help developers understand the hardware enable state of clks in case
firmware or bootloader state is different than what is expected.
Overall the core changes are mostly improving the clk driver writing
experience.
At the driver level, we have the usual collection of driver updates
and new drivers for new SoCs. This time around the Qualcomm folks
introduced a good handful of clk drivers for various parts of three or
four SoCs. The SiFive folks added a new clk driver for their FU740
SoCs, coming in second on the diffstat and then Atmel AT91 and Amlogic
SoCs had lots of work done after that for various new features. One
last thing to note in the driver area is that the i.MX driver has
gained a new binding to support SCU clks after being on the list for
many months. It uses a two cell binding which is sort of rare in clk
DT bindings. Beyond that we have the usual set of driver fixes and
tweaks that come from more testing and finding out that some
configuration was wrong or that a driver could support being built as
a module.
Summary:
Core:
- Add some trace points for clk_set_rate() "range" functions
- Add hardware enable information to clk_summary debugfs
- Replace clk-provider.h with of_clk.h when possible
- Add devm variant of clk_notifier_register()
- Add clk_hw_get_clk() to generate a struct clk from a struct clk_hw
New Drivers:
- Bindings for Canaan K210 SoC clks
- Support for SiFive FU740 PRCI
- Camera clks on Qualcomm SC7180 SoCs
- GCC and RPMh clks on Qualcomm SDX55 SoCs
- RPMh clks on Qualcomm SM8350 SoCs
- LPASS clks on Qualcomm SM8250 SoCs
Updates:
- DVFS support for AT91 clk driver
- Update git repo branch for Renesas clock drivers
- Add camera (CSI) and video-in (VIN) clocks on Renesas R-Car V3U
- Add RPC (QSPI/HyperFLASH) clocks on Renesas RZ/G2M, RZ/G2N, and RZ/G2E
- Stop using __raw_*() I/O accessors in Renesas clk drivers
- One more conversion of DT bindings to json-schema
- Make i.MX clk-gate2 driver more flexible
- New two cell binding for i.MX SCU clks
- Drop of_match_ptr() in i.MX8 clk drivers
- Add arch dependencies for Rockchip clk drivers
- Fix i2s on Rockchip rk3066
- Add MIPI DSI clks on Amlogic axg and g12 SoCs
- Support modular builds of Amlogic clk drivers
- Fix an Amlogic Video PLL clock dependency
- Samsung Kconfig dependencies updates for better compile test coverage
- Refactoring of the Samsung PLL clocks driver
- Small Tegra driver cleanups
- Minor fixes to Ingenic and VC5 clk drivers
- Cleanup patches to remove unused variables and plug memory leaks"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (134 commits)
dt-binding: clock: Document canaan,k210-clk bindings
dt-bindings: Add Canaan vendor prefix
clk: vc5: Use "idt,voltage-microvolt" instead of "idt,voltage-microvolts"
clk: ingenic: Fix divider calculation with div tables
clk: sunxi-ng: Make sure divider tables have sentinel
clk: s2mps11: Fix a resource leak in error handling paths in the probe function
clk: mvebu: a3700: fix the XTAL MODE pin to MPP1_9
clk: si5351: Wait for bit clear after PLL reset
clk: at91: sam9x60: remove atmel,osc-bypass support
clk: at91: sama7g5: register cpu clock
clk: at91: clk-master: re-factor master clock
clk: at91: sama7g5: do not allow cpu pll to go higher than 1GHz
clk: at91: sama7g5: decrease lower limit for MCK0 rate
clk: at91: sama7g5: remove mck0 from parent list of other clocks
clk: at91: clk-sam9x60-pll: allow runtime changes for pll
clk: at91: sama7g5: add 5th divisor for mck0 layout and characteristics
clk: at91: clk-master: add 5th divisor for mck master
clk: at91: sama7g5: allow SYS and CPU PLLs to be exported and referenced in DT
dt-bindings: clock: at91: add sama7g5 pll defines
clk: at91: sama7g5: fix compilation error
...
|
|
This issue can be reproduced by having a kernel config with
CONFIG_IMX_MBOX=m and CONFIG_MXC_CLK_SCU=m. It's caused by the Makefile
wanting to build clk-scu.o and clk-imx8qxp.o as different targets but
that doesn't work (e.g. MXC_CLK_SCU = y while CLK_IMX8QXP = n)
"obj-$(CONFIG_MXC_CLK_SCU) += clk-imx-scu.o clk-imx-lpcg-scu.o
clk-imx-scu-$(CONFIG_CLK_IMX8QXP) += clk-scu.o clk-imx8qxp.o"
Having MXC_CLK_SCU=y/m while CLK_IMX8QXP=n will cause a linker problem
like below:
LD [M] drivers/clk/imx/clk-imx-scu.o
arm-poky-linux-gnueabi-ld: no input files
Make MXC_CLK_SCU be un-selectable by users so it can only be selected by
the CLK_IMX8QXP option, ensuring the two symbols are built together.
Drop COMPILE_TEST too because this option isn't selectable anymore. We
can remove it from MXC_CLK_SCU because CLK_IMX8QXP selects MXC_CLK_SCU
which already has COMPILE_TEST.
Fixes: e0d0d4d86c766 ("clk: imx8qxp: Support building i.MX8QXP clock driver as module")
Acked-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Link: https://lore.kernel.org/r/20201130084624.21113-1-aisheng.dong@nxp.com
[sboyd@kernel.org: Rework commit text]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The device_is_bound() is invisible to drivers when built as modules.
It's also not aimed to be used by drivers according to Greg K.H.
Let's remove it from clk-scu driver and find another way to do proper
driver loading sequence.
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <kernel@pengutronix.de>
Cc: Stephen Boyd <sboyd@kernel.org>
Fixes: 77d8f3068c63 ("clk: imx: scu: add two cells binding support")
Reported-by: Sudip Mukherjee <sudipm.mukherjee@gmail.com>
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Fix the following sparse warning:
./clk-scu.c:23:20: warning: symbol 'pd_np' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mq.c:626:34: warning:
‘imx8mq_clk_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mp.c:751:34: warning:
‘imx8mp_clk_of_match’ defined but not used [-Wunused-const-variable=]
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mn.c:592:34: warning:
‘imx8mn_clk_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The driver can match only via the DT table so the table should be always
used and the of_match_ptr does not have any sense (this also allows ACPI
matching via PRP0001, even though it might be not relevant here). This
fixes compile warning (!CONFIG_OF && !CONFIG_MODULES):
drivers/clk/imx/clk-imx8mm.c:641:34: warning:
‘imx8mm_clk_of_match’ defined but not used [-Wunused-const-variable=]
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch fixes below warning reported by coccicheck:
./clk-gate2.c:57:5-8: Unneeded variable: "ret". Return "0" on line 68
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: Zou Wei <zou_wei@huawei.com>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
noc/axi/ahb are bus clk, not peripheral clk.
Since peripheral clk has a limitation that for peripheral clock slice,
IP clock slices must be stopped to change the clock source.
However if the bus clk is marked as critical clk peripheral, the
assigned clock parent operation will fail.
So we added CLK_SET_PARENT_GATE flag to avoid glitch.
And add imx8m_clk_hw_composite_bus_critical for bus critical clock usage
Fixes: 936c383673b9e ("clk: imx: fix composite peripheral flags")
Reviewed-by: Abel Vesa <abel.vesa@nxp.com>
Reported-by: Abel Vesa <abel.vesa@nxp.com>
Signed-off-by: Peng Fan <peng.fan@nxp.com>
Link: https://lore.kernel.org/r/1604229834-25594-1-git-send-email-peng.fan@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Protect against enabling/disabling the gate while we're
checking if it is enabled.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On some i.MX8 platforms, there are HW gates that share the same bit.
So in order to make this clock type more usable, use a mask to specify
how many bits belong to those HW gates.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Seems the logic here was wrong all along. For example, if
the cgr_val is 2 (0b10), the clk_gate2_reg_is_enabled would
report the clock as disabled. So check against cgr_val instead.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Move all the register writing to the newly added clk_gate2_do_shared_clks
and call that everywhere need needed. Cleans up the code a little bit.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This was a hack which would allow multiple HW gates to be controlled
by a single bit. The only user of this is the imx_dev_clk_hw_gate_shared
which is not used anywhere as of now. Basically, complicates the logic
of the driver for no reason.
Signed-off-by: Abel Vesa <abel.vesa@nxp.com>
Reviewed-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
After commit e0d0d4d86c76 ("clk: imx8qxp: Support building i.MX8QXP clock
driver as module"), clk-scu.c and clk-imx8qxp.c are complied in one module,
thus there can be only one module_init() in those two files.
Commit 77d8f3068c63 ("clk: imx: scu: add two cells binding support")
introduced another module_init() in clk_scu.c which caused the errors
below.
To fix the issue, we can remove the unnecessary builtin_platform_driver
from clk_scu.c and directly register the driver in imx_clk_scu_init().
CC [M] drivers/clk/imx/clk-scu.o
In file included from ../include/linux/of_device.h:6,
from ../include/linux/of_platform.h:12,
from ../drivers/clk/imx/clk-scu.c:11:
../drivers/clk/imx/clk-scu.c: In function ‘imx_clk_scu_init’:
../drivers/clk/imx/clk-scu.c:176:35: error: ‘imx_clk_scu_driver’ undeclared (first use in this function); did you mean ‘imx_clk_scu_init’?
176 | return platform_driver_register(&imx_clk_scu_driver);
| ^~~~~~~~~~~~~~~~~~
../include/linux/platform_device.h:218:29: note: in definition of macro ‘platform_driver_register’
218 | __platform_driver_register(drv, THIS_MODULE)
| ^~~
../drivers/clk/imx/clk-scu.c:176:35: note: each undeclared identifier is reported only once for each function it appears in
176 | return platform_driver_register(&imx_clk_scu_driver);
| ^~~~~~~~~~~~~~~~~~
../include/linux/platform_device.h:218:29: note: in definition of macro ‘platform_driver_register’
218 | __platform_driver_register(drv, THIS_MODULE)
| ^~~
../drivers/clk/imx/clk-scu.c:177:1: error: control reaches end of non-void function [-Werror=return-type]
177 | }
| ^
At top level:
../drivers/clk/imx/clk-scu.c:470:31: warning: ‘imx_clk_scu_driver’ defined but not used [-Wunused-variable]
470 | static struct platform_driver imx_clk_scu_driver = {
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 77d8f3068c63 ("clk: imx: scu: add two cells binding support")
Signed-off-by: Dong Aisheng <aisheng.dong@nxp.com>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
