diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/atmel-nand.txt | 31 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/fsl-quadspi.txt | 5 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/mtd/qcom_nandc.txt | 86 |
3 files changed, 108 insertions, 14 deletions
diff --git a/Documentation/devicetree/bindings/mtd/atmel-nand.txt b/Documentation/devicetree/bindings/mtd/atmel-nand.txt index 7d4c8eb775a5..d53aba98fbc9 100644 --- a/Documentation/devicetree/bindings/mtd/atmel-nand.txt +++ b/Documentation/devicetree/bindings/mtd/atmel-nand.txt @@ -1,7 +1,10 @@ Atmel NAND flash Required properties: -- compatible : should be "atmel,at91rm9200-nand" or "atmel,sama5d4-nand". +- compatible: The possible values are: + "atmel,at91rm9200-nand" + "atmel,sama5d2-nand" + "atmel,sama5d4-nand" - reg : should specify localbus address and size used for the chip, and hardware ECC controller if available. If the hardware ECC is PMECC, it should contain address and size for @@ -21,10 +24,11 @@ Optional properties: - nand-ecc-mode : String, operation mode of the NAND ecc mode, soft by default. Supported values are: "none", "soft", "hw", "hw_syndrome", "hw_oob_first", "soft_bch". -- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware. - Only supported by at91sam9x5 or later sam9 product. +- atmel,has-pmecc : boolean to enable Programmable Multibit ECC hardware, + capable of BCH encoding and decoding, on devices where it is present. - atmel,pmecc-cap : error correct capability for Programmable Multibit ECC - Controller. Supported values are: 2, 4, 8, 12, 24. + Controller. Supported values are: 2, 4, 8, 12, 24. If the compatible string + is "atmel,sama5d2-nand", 32 is also valid. - atmel,pmecc-sector-size : sector size for ECC computation. Supported values are: 512, 1024. - atmel,pmecc-lookup-table-offset : includes two offsets of lookup table in ROM @@ -32,15 +36,16 @@ Optional properties: sector size 1024. If not specified, driver will build the table in runtime. - nand-bus-width : 8 or 16 bus width if not present 8 - nand-on-flash-bbt: boolean to enable on flash bbt option if not present false -- Nand Flash Controller(NFC) is a slave driver under Atmel nand flash - - Required properties: - - compatible : "atmel,sama5d3-nfc". - - reg : should specify the address and size used for NFC command registers, - NFC registers and NFC Sram. NFC Sram address and size can be absent - if don't want to use it. - - clocks: phandle to the peripheral clock - - Optional properties: - - atmel,write-by-sram: boolean to enable NFC write by sram. + +Nand Flash Controller(NFC) is an optional sub-node +Required properties: +- compatible : "atmel,sama5d3-nfc" or "atmel,sama5d4-nfc". +- reg : should specify the address and size used for NFC command registers, + NFC registers and NFC SRAM. NFC SRAM address and size can be absent + if don't want to use it. +- clocks: phandle to the peripheral clock +Optional properties: +- atmel,write-by-sram: boolean to enable NFC write by SRAM. Examples: nand0: nand@40000000,0 { diff --git a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt index 00c587b3d3ae..0333ec87dc49 100644 --- a/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt +++ b/Documentation/devicetree/bindings/mtd/fsl-quadspi.txt @@ -3,7 +3,9 @@ Required properties: - compatible : Should be "fsl,vf610-qspi", "fsl,imx6sx-qspi", "fsl,imx7d-qspi", "fsl,imx6ul-qspi", - "fsl,ls1021-qspi" + "fsl,ls1021a-qspi" + or + "fsl,ls2080a-qspi" followed by "fsl,ls1021a-qspi" - reg : the first contains the register location and length, the second contains the memory mapping address and length - reg-names: Should contain the reg names "QuadSPI" and "QuadSPI-memory" @@ -19,6 +21,7 @@ Optional properties: But if there are two NOR flashes connected to the bus, you should enable this property. (Please check the board's schematic.) + - big-endian : That means the IP register is big endian Example: diff --git a/Documentation/devicetree/bindings/mtd/qcom_nandc.txt b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt new file mode 100644 index 000000000000..70dd5118a324 --- /dev/null +++ b/Documentation/devicetree/bindings/mtd/qcom_nandc.txt @@ -0,0 +1,86 @@ +* Qualcomm NAND controller + +Required properties: +- compatible: should be "qcom,ipq806x-nand" +- reg: MMIO address range +- clocks: must contain core clock and always on clock +- clock-names: must contain "core" for the core clock and "aon" for the + always on clock +- dmas: DMA specifier, consisting of a phandle to the ADM DMA + controller node and the channel number to be used for + NAND. Refer to dma.txt and qcom_adm.txt for more details +- dma-names: must be "rxtx" +- qcom,cmd-crci: must contain the ADM command type CRCI block instance + number specified for the NAND controller on the given + platform +- qcom,data-crci: must contain the ADM data type CRCI block instance + number specified for the NAND controller on the given + platform +- #address-cells: <1> - subnodes give the chip-select number +- #size-cells: <0> + +* NAND chip-select + +Each controller may contain one or more subnodes to represent enabled +chip-selects which (may) contain NAND flash chips. Their properties are as +follows. + +Required properties: +- compatible: should contain "qcom,nandcs" +- reg: a single integer representing the chip-select + number (e.g., 0, 1, 2, etc.) +- #address-cells: see partition.txt +- #size-cells: see partition.txt +- nand-ecc-strength: see nand.txt +- nand-ecc-step-size: must be 512. see nand.txt for more details. + +Optional properties: +- nand-bus-width: see nand.txt + +Each nandcs device node may optionally contain a 'partitions' sub-node, which +further contains sub-nodes describing the flash partition mapping. See +partition.txt for more detail. + +Example: + +nand@1ac00000 { + compatible = "qcom,ebi2-nandc"; + reg = <0x1ac00000 0x800>; + + clocks = <&gcc EBI2_CLK>, + <&gcc EBI2_AON_CLK>; + clock-names = "core", "aon"; + + dmas = <&adm_dma 3>; + dma-names = "rxtx"; + qcom,cmd-crci = <15>; + qcom,data-crci = <3>; + + #address-cells = <1>; + #size-cells = <0>; + + nandcs@0 { + compatible = "qcom,nandcs"; + reg = <0>; + + nand-ecc-strength = <4>; + nand-ecc-step-size = <512>; + nand-bus-width = <8>; + + partitions { + compatible = "fixed-partitions"; + #address-cells = <1>; + #size-cells = <1>; + + partition@0 { + label = "boot-nand"; + reg = <0 0x58a0000>; + }; + + partition@58a0000 { + label = "fs-nand"; + reg = <0x58a0000 0x4000000>; + }; + }; + }; +}; |