blob: 1730290d460e8364db952d5c0b11727bf3e5833a (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
|
/***************************************************************************
* __________ __ ___.
* Open \______ \ ____ ____ | | _\_ |__ _______ ___
* Source | _// _ \_/ ___\| |/ /| __ \ / _ \ \/ /
* Jukebox | | ( <_> ) \___| < | \_\ ( <_> > < <
* Firmware |____|_ /\____/ \___ >__|_ \|___ /\____/__/\_ \
* \/ \/ \/ \/ \/
* $Id$
*
* Copyright (C) 2009 by Bertrik Sikken
*
* This program is free software; you can redistribute it and/or
* modify it under the terms of the GNU General Public License
* as published by the Free Software Foundation; either version 2
* of the License, or (at your option) any later version.
*
* This software is distributed on an "AS IS" basis, WITHOUT WARRANTY OF ANY
* KIND, either express or implied.
*
****************************************************************************/
#include "config.h"
#include <inttypes.h>
#include "as3525.h"
#include "dbop-as3525.h"
#if defined(SANSA_FUZE) || defined(SANSA_FUZEV2)
#define DBOP_PRECHARGE 0x80FF
#elif defined(SANSA_E200V2) || defined(SANSA_C200V2)
#define DBOP_PRECHARGE 0xF0FF
#endif
static short int dbop_input_value = 0;
/* read the DBOP data pins */
unsigned short dbop_read_input(void)
{
unsigned int dbop_ctrl_old = DBOP_CTRL;
unsigned int dbop_timpol23_old = DBOP_TIMPOL_23;
/* make sure that the DBOP FIFO is empty */
while ((DBOP_STAT & (1<<10)) == 0);
/* write DBOP_DOUT to pre-charge DBOP data lines with a defined level */
DBOP_TIMPOL_23 = 0xe007e007; /* no strobe towards lcd */
int delay = 10;
while (delay--) asm volatile ("nop\n");
DBOP_CTRL = (1 << 19) | /* tri-state output */
(1 << 16) | /* enw=1 (enable write) */
(1 << 12); /* ow=1 (16-bit data width) */
DBOP_DOUT = DBOP_PRECHARGE;
while ((DBOP_STAT & (1<<10)) == 0);
#if defined(SANSA_FUZE) || defined(SANSA_E200V2)
delay = 50;
while (delay--) asm volatile ("nop\n");
#endif
/* perform a DBOP read */
DBOP_CTRL = (1 << 19) | /* tri-state output */
(1 << 15) | /* strd=1 (start read) */
(1 << 12) | /* ow=1 (16-bit data width) */
(31 << 0); /* rs_t=31 (read DBOP at end of cycle) */
while ((DBOP_STAT & (1<<16)) == 0);
dbop_input_value = DBOP_DIN;
/* restore previous values */
DBOP_TIMPOL_23 = dbop_timpol23_old;
DBOP_CTRL = dbop_ctrl_old;
return dbop_input_value;
}
/* for the debug menu */
unsigned short dbop_debug(void)
{
return dbop_input_value;
}
static inline void dbop_set_mode(int mode)
{
int delay = 10;
if (mode == 32 && (!(DBOP_CTRL & (1<<13|1<<14))))
DBOP_CTRL |= (1<<13|1<<14);
else if (mode == 16 && (DBOP_CTRL & (1<<13|1<<14)))
DBOP_CTRL &= ~(1<<14|1<<13);
else
return;
while(delay--) asm volatile("nop");
}
void dbop_write_data(const int16_t* p_bytes, int count)
{
const int32_t *data;
if ((intptr_t)p_bytes & 0x3 || count == 1)
{ /* need to do a single 16bit write beforehand if the address is
* not word aligned or count is 1, switch to 16bit mode if needed */
dbop_set_mode(16);
DBOP_DOUT16 = *p_bytes++;
if (!(--count))
return;
}
/* from here, 32bit transfers are save
* set it to transfer 4*(outputwidth) units at a time,
* if bit 12 is set it only does 2 halfwords though (we never set it)
* switch to 32bit output if needed */
dbop_set_mode(32);
data = (int32_t*)p_bytes;
while (count > 1)
{
DBOP_DOUT32 = *data++;
count -= 2;
/* Wait if push fifo is full */
while ((DBOP_STAT & (1<<6)) != 0);
}
/* While push fifo is not empty */
while ((DBOP_STAT & (1<<10)) == 0);
/* due to the 32bit alignment requirement or uneven count,
* we possibly need to do a 16bit transfer at the end also */
if (count > 0)
dbop_write_data((int16_t*)data, 1);
}
|
