as3525v2: enable AFE (AUDIO Front End) interrupts

We needed to set the XIRQ output pin

git-svn-id: svn://svn.rockbox.org/rockbox/trunk@26238 a1c6a512-1295-4272-9138-f99709370657

1 files changed, 16 insertions, 54 deletions

diff --git a/firmware/target/arm/as3525/ascodec-as3525.c b/firmware/target/arm/as3525/ascodec-as3525.c
index adc9b7f9a8..708215deed 100644
--- a/firmware/target/arm/as3525/ascodec-as3525.c
+++ b/firmware/target/arm/as3525/ascodec-as3525.c
@@ -96,7 +96,6 @@ static unsigned char *req_data_ptr = NULL;
 static struct ascodec_request *req_head = NULL;
 static struct ascodec_request *req_tail = NULL;
 
-#if CONFIG_CPU == AS3525
 static struct wakeup adc_wkup;
 static struct ascodec_request as_audio_req;
 
@@ -112,13 +111,11 @@ static int int_adc = 0;
 #endif /* DEBUG */
 
 static void ascodec_read_cb(unsigned const char *data, unsigned int len);
-#endif /* CONFIG_CPU == AS3525 */
 
 static void ascodec_start_req(struct ascodec_request *req);
 static int  ascodec_continue_req(struct ascodec_request *req, int irq_status);
 static void ascodec_finish_req(struct ascodec_request *req);
 
-#if CONFIG_CPU == AS3525
 void INT_AUDIO(void)
 {
     VIC_INT_EN_CLEAR = INTERRUPT_AUDIO;
@@ -126,7 +123,6 @@ void INT_AUDIO(void)
 
     ascodec_async_read(AS3514_IRQ_ENRD0, 3, &as_audio_req, ascodec_read_cb);
 }
-#endif /* CONFIG_CPU == AS3525 */
 
 void INT_I2C_AUDIO(void)
 {
@@ -166,9 +162,7 @@ void ascodec_init(void)
     int prescaler;
 
     mutex_init(&as_mtx);
-#if CONFIG_CPU == AS3525
     wakeup_init(&adc_wkup);
-#endif
 
     /* enable clock */
     CGU_PERI |= CGU_I2C_AUDIO_MASTER_CLOCK_ENABLE;
@@ -186,9 +180,7 @@ void ascodec_init(void)
     I2C2_IMR = 0x00;          /* disable interrupts */
     I2C2_INT_CLR |= I2C2_RIS; /* clear interrupt status */
     VIC_INT_ENABLE = INTERRUPT_I2C_AUDIO;
-#if CONFIG_CPU == AS3525 /* interrupts do not work correctly on as3525v2 */
     VIC_INT_ENABLE = INTERRUPT_AUDIO;
-#endif
 
     /* detect if USB was connected at startup since there is no transition */
     if(ascodec_read(AS3514_IRQ_ENRD0) & USB_STATUS)
@@ -203,9 +195,16 @@ void ascodec_init(void)
 #endif
         IRQ_USBSTAT);
 
+#if CONFIG_CPU == AS3525v2
+    /* XIRQ = IRQ, active low reset signal, 6mA push-pull output */
+    ascodec_write_pmu(0x1a, 3, (1<<2)|3); /* 1A-3 = Out_Cntr3 register */
+    /* Generate irq on (rtc,) adc change */
+    ascodec_write(AS3514_IRQ_ENRD2, /*IRQ_RTC |*/ IRQ_ADC);
+#else
     /* Generate irq for push-pull, active high, irq on rtc+adc change */
     ascodec_write(AS3514_IRQ_ENRD2, IRQ_PUSHPULL | IRQ_HIGHACTIVE |
                                     /*IRQ_RTC |*/ IRQ_ADC);
+#endif
 }
 
 /* returns != 0 when busy */
@@ -432,28 +431,17 @@ int ascodec_readbytes(unsigned int index, unsigned int len, unsigned char *data)
     return i;
 }
 
-/*
- * Reading AS3514_IRQ_ENRD0 clears all interrupt bits, so we cache the results
- * and clear individual bits when a specific interrupt is checked:
- * - we clear the ENDOFCH (end of charge) interrupt when it's read
- * - we set the usb and charger presence when the status change is detected
- *
- * on AS3525(v1) ENRD0 is only read in an interrupt handler
- * on AS3525v2 the interrupt handler doesn't work (yet), so we read the register
- * synchronously.
- *  - To avoid race conditions all the reads to this register must be atomic.
- *    We don't need to disable interrupts when reading it because all the reads
- *    (in powermgmt-ascodec.c and power-as3525.c) are performed by the same
- *    thread (the power thread).
- */
-static void cache_enrd0(int enrd0)
+static void ascodec_read_cb(unsigned const char *data, unsigned int len)
 {
-    if (enrd0 & CHG_ENDOFCH) { /* chg finished */
+    if (len != 3) /* some error happened? */
+        return;
+
+    if (data[0] & CHG_ENDOFCH) { /* chg finished */
         ascodec_enrd0_shadow |= CHG_ENDOFCH;
         IFDEBUG(int_chg_finished++);
     }
-    if (enrd0 & CHG_CHANGED) { /* chg status changed */
-        if (enrd0 & CHG_STATUS) {
+    if (data[0] & CHG_CHANGED) { /* chg status changed */
+        if (data[0] & CHG_STATUS) {
             ascodec_enrd0_shadow |= CHG_STATUS;
             IFDEBUG(int_chg_insert++);
         } else {
@@ -461,8 +449,8 @@ static void cache_enrd0(int enrd0)
             IFDEBUG(int_chg_remove++);
         }
     }
-    if (enrd0 & USB_CHANGED) { /* usb status changed */
-        if (enrd0 & USB_STATUS) {
+    if (data[0] & USB_CHANGED) { /* usb status changed */
+        if (data[0] & USB_STATUS) {
             IFDEBUG(int_usb_insert++);
             usb_insert_int();
         } else {
@@ -470,16 +458,6 @@ static void cache_enrd0(int enrd0)
             usb_remove_int();
         }
     }
-}
-
-#if CONFIG_CPU == AS3525
-static void ascodec_read_cb(unsigned const char *data, unsigned int len)
-{
-    if (len != 3) /* some error happened? */
-        return;
-
-    cache_enrd0(data[0]);
-
     if (data[2] & IRQ_RTC) { /* rtc irq */
         /*
          * Can be configured for once per second or once per minute,
@@ -494,27 +472,14 @@ static void ascodec_read_cb(unsigned const char *data, unsigned int len)
     VIC_INT_ENABLE = INTERRUPT_AUDIO;
 }
 
-#endif /* CONFIG_CPU == AS3525 */
-
 void ascodec_wait_adc_finished(void)
 {
-#if CONFIG_CPU == AS3525
     wakeup_wait(&adc_wkup, TIMEOUT_BLOCK);
-#else
-    /* no interrupts, busy wait
-     * XXX: make sure this is the only reader of IRQ_ENRD2
-     */
-    while(!(ascodec_read(AS3514_IRQ_ENRD2) & IRQ_ADC))
-        yield();
-#endif
 }
 
 #ifdef CONFIG_CHARGING
 bool ascodec_endofch(void)
 {
-#if CONFIG_CPU != AS3525
-    cache_enrd0(ascodec_read(AS3514_IRQ_ENRD0));
-#endif
     bool ret = ascodec_enrd0_shadow & CHG_ENDOFCH;
     ascodec_enrd0_shadow &= ~CHG_ENDOFCH; // clear interrupt
     return ret;
@@ -522,9 +487,6 @@ bool ascodec_endofch(void)
 
 bool ascodec_chg_status(void)
 {
-#if CONFIG_CPU != AS3525
-    cache_enrd0(ascodec_read(AS3514_IRQ_ENRD0));
-#endif
     return ascodec_enrd0_shadow & CHG_STATUS;
 }
 #endif /* CONFIG_CHARGING */