Improved H10 ADC driver. We now do things exactly as the OF does. This includes shifting the readings by 0x14 when PLL is enabled. Battery voltages and remote/scrollpad values adjusted accordingly. We also now wait for the ADC to indicate the conversion is complete before reading the data, so hopefully we will get more reliably steady readings.

git-svn-id: svn://svn.rockbox.org/rockbox/trunk@15141 a1c6a512-1295-4272-9138-f99709370657

10 files changed, 92 insertions, 57 deletions

diff --git a/firmware/target/arm/iriver/h10/adc-h10.c b/firmware/target/arm/iriver/h10/adc-h10.c
index df9b16359b..f63e8b8013 100644
--- a/firmware/target/arm/iriver/h10/adc-h10.c
+++ b/firmware/target/arm/iriver/h10/adc-h10.c
@@ -25,29 +25,21 @@
 
 static unsigned short adcdata[NUM_ADC_CHANNELS];
 
-/* Scan ADC so that adcdata[channel] gets updated */
+/* Scan ADC so that adcdata[channel] gets updated. */
 unsigned short adc_scan(int channel)
 {
     unsigned int adc_data_1;
     unsigned int adc_data_2;
 
-    /* Initialise */
-    ADC_ADDR=0x130;
-    ADC_STATUS=0;   /* 4 bytes, 1 per channel. Each byte is 0 if the channel is
-                       off, 0x40 if the channel is on */
+    /* Start conversion */
+    ADC_ADDR |= 0x80000000;
     
-    /* Enable Channel */
-    ADC_ADDR |= (0x1000000<<channel);
+    /* Wait for conversion to complete */
+    while((ADC_STATUS & (0x40<<8*channel))==0);
+    
+    /* Stop conversion */
+    ADC_ADDR &=~ 0x80000000;
     
-    /* Start? */
-    ADC_ADDR |= 0x20000000;
-    ADC_ADDR |= 0x80000000;
-
-#if 0
-    /* wait for ADC ready. THIS IS NOT WORKING (locks up) */
-    while(ADC_STATUS & (0x40 << (channel*8))); /* add loop protection here */
-#endif
-
     /* ADC_DATA_1 and ADC_DATA_2 are both four bytes, one byte per channel.
        For each channel, ADC_DATA_1 stores the 8-bit msb, ADC_DATA_2 stores the
        2-bit lsb (in bits 0 and 1). Each channel is 10 bits total. */
@@ -56,6 +48,13 @@ unsigned short adc_scan(int channel)
     
     adcdata[channel] = (adc_data_1<<2 | adc_data_2);
     
+    /* ADC values read low if PLL is enabled */
+    if(PLL_CONTROL & 0x80000000){
+        adcdata[channel] += 0x14;
+        if(adcdata[channel] > 0x400)
+            adcdata[channel] = 0x400;
+    }
+    
     return adcdata[channel];
 }
 
@@ -79,25 +78,64 @@ static void adc_tick(void)
     }
 }
 
+/* Figured out from how the OF does things */
 void adc_init(void)
 {
-    /* Enable ADC */
-    ADC_ENABLE_ADDR |= ADC_ENABLE;
+    ADC_INIT |= 1;
+    ADC_INIT |= 0x40000000;
+    udelay(100);
+    
+    /* Reset ADC */
+    DEV_RS2 |= 0x20;
+    udelay(100);
+    
+    DEV_RS2 &=~ 0x20;
+    udelay(100);
     
-    /* Initialise */
-    ADC_INIT=0;
+    /* Enable ADC */
+    DEV_EN2 |= 0x20;
+    udelay(100);
+
+    ADC_CLOCK_SRC |= 0x3;
+    udelay(100);
+
+    ADC_ADDR |= 0x40;
+    ADC_ADDR |= 0x20000000;
+    udelay(100);
+
+    ADC_INIT;
+    ADC_INIT = 0;
+    udelay(100);
+
+    ADC_STATUS = 0;
+
+    /* Enable channel 0 (battery) */
+    DEV_INIT1  &=~0x3;
+    ADC_ADDR   |= 0x1000000;
+    ADC_STATUS |= 0x20;
+
+    /* Enable channel 1 (unknown, temperature?) */
+    DEV_INIT1  &=~30;
+    ADC_ADDR   |= 0x2000000;
+    ADC_STATUS |= 0x2000;
+
+    /* Enable channel 2 (remote) */
+    DEV_INIT1  &=~0x300;
+    DEV_INIT1  |= 0x100;
+    ADC_ADDR   |= 0x4000000;
+    ADC_STATUS |= 0x200000;
+
+    /* Enable channel 3 (scroll pad) */
+    DEV_INIT1  &=~0x3000;
+    DEV_INIT1  |= 0x1000;
+    ADC_ADDR   |= 0x8000000;
+    ADC_STATUS |= 0x20000000;
 
     /* Force a scan of all channels to get initial values */
     adc_scan(ADC_BATTERY);
     adc_scan(ADC_UNKNOWN_1);
     adc_scan(ADC_REMOTE);
     adc_scan(ADC_SCROLLPAD);
-    
-    /* FIXME: The ADC sometimes reads 0 for the battery
-       voltage for the first few seconds. It would be better to fix this by
-       figuring out how to use the ADC properly. Until then, work around the
-       problem by waiting until it reads a proper value*/
-    while(adc_scan(ADC_UNREG_POWER)==0);
 
     tick_add_task(adc_tick);
 }
diff --git a/firmware/target/arm/iriver/h10/adc-target.h b/firmware/target/arm/iriver/h10/adc-target.h
index 741c293baa..f761e761ef 100644
--- a/firmware/target/arm/iriver/h10/adc-target.h
+++ b/firmware/target/arm/iriver/h10/adc-target.h
@@ -19,9 +19,6 @@
 #ifndef _ADC_TARGET_H_
 #define _ADC_TARGET_H_
 
-#define ADC_ENABLE_ADDR     (*(volatile unsigned long*)(0x70000010))
-#define ADC_ENABLE          0x1100
-
 #define ADC_ADDR            (*(volatile unsigned long*)(0x7000ad00))
 #define ADC_STATUS          (*(volatile unsigned long*)(0x7000ad04))
 #define ADC_DATA_1          (*(volatile unsigned long*)(0x7000ad20))
diff --git a/firmware/target/arm/iriver/h10/button-h10.c b/firmware/target/arm/iriver/h10/button-h10.c
index d8a82cf170..ac09d245e6 100644
--- a/firmware/target/arm/iriver/h10/button-h10.c
+++ b/firmware/target/arm/iriver/h10/button-h10.c
@@ -52,7 +52,7 @@ bool button_hold(void)
 
 bool remote_button_hold(void)
 {
-    return adc_scan(ADC_REMOTE) < 0x17;
+    return adc_scan(ADC_REMOTE) < 0x2B;
 }
 
 /*
@@ -102,7 +102,7 @@ int button_read_device(void)
             data = adc_scan(ADC_SCROLLPAD);
             GPIOD_OUTPUT_VAL |= 0x40;
             
-            if(data < 0x210)
+            if(data < 0x224)
             {
                 btn |= BUTTON_SCROLL_DOWN;
             } else {
@@ -115,7 +115,7 @@ int button_read_device(void)
     remote_hold_button_old = remote_hold_button;
 
     data = adc_scan(ADC_REMOTE);
-    remote_hold_button = data < 0x17;
+    remote_hold_button = data < 0x2B;
 
 #ifndef BOOTLOADER
     if (remote_hold_button != remote_hold_button_old)
@@ -126,13 +126,13 @@ int button_read_device(void)
     {
         if (data < 0x3FF)
         {
-            if(data < 0x1F0)
-                if(data < 0x141)
+            if(data < 0x204)
+                if(data < 0x155)
                     btn |= BUTTON_RC_FF;
                 else
                     btn |= BUTTON_RC_REW;
             else
-                if(data < 0x2BC)
+                if(data < 0x2D0)
                    btn |= BUTTON_RC_VOL_DOWN;
                 else
                     btn |= BUTTON_RC_VOL_UP;
diff --git a/firmware/target/arm/iriver/h10/powermgmt-h10.c b/firmware/target/arm/iriver/h10/powermgmt-h10.c
index 18e3879c43..6f8cd12276 100644
--- a/firmware/target/arm/iriver/h10/powermgmt-h10.c
+++ b/firmware/target/arm/iriver/h10/powermgmt-h10.c
@@ -25,18 +25,18 @@
 const unsigned short battery_level_dangerous[BATTERY_TYPES_COUNT] =
 {
 #ifdef IRIVER_H10
-    3760
+    3733
 #elif defined IRIVER_H10_5GB
-    3720
+    3695
 #endif
 };
 
 const unsigned short battery_level_shutoff[BATTERY_TYPES_COUNT] =
 {
 #ifdef IRIVER_H10
-    3650
+    3627
 #elif defined IRIVER_H10_5GB
-    3650
+    3627
 #endif
 };
 
@@ -44,9 +44,9 @@ const unsigned short battery_level_shutoff[BATTERY_TYPES_COUNT] =
 const unsigned short percent_to_volt_discharge[BATTERY_TYPES_COUNT][11] =
 {
 #ifdef IRIVER_H10
-    { 3760, 3800, 3850, 3870, 3900, 3950, 4020, 4070, 4110, 4180, 4240 }
+    { 3733, 3772, 3821, 3840, 3869, 3917, 3985, 4034, 4072, 4140, 4198 }
 #elif defined IRIVER_H10_5GB
-    { 3720, 3740, 3800, 3820, 3840, 3880, 3940, 4020, 4060, 4150, 4240 }
+    { 3695, 3714, 3772, 3791, 3811, 3850, 3908, 3985, 4024, 4111, 4198 }
 #endif
 };
 
@@ -54,14 +54,14 @@ const unsigned short percent_to_volt_discharge[BATTERY_TYPES_COUNT][11] =
 const unsigned short percent_to_volt_charge[11] =
 {
 #ifdef IRIVER_H10
-    3990, 4030, 4060, 4080, 4100, 4120, 4150, 4180, 4220, 4260, 4310
+    3956, 3995, 4024, 4043, 4063, 4082, 4111, 4140, 4179, 4218, 4266
 #elif defined IRIVER_H10_5GB
     /* TODO: Not yet calibrated */
-    3880, 3920, 3960, 4000, 4060, 4100, 4150, 4190, 4240, 4280, 4330
+    3850, 3888, 3927, 3966, 4024, 4063, 4111, 4150, 4198, 4237, 4286
 #endif
 };
 
-#define BATTERY_SCALE_FACTOR 4800
+#define BATTERY_SCALE_FACTOR 4650
 /* full-scale ADC readout (2^10) in millivolt */
 
 /* Returns battery voltage from ADC [millivolts] */
diff --git a/firmware/target/arm/sandisk/power-c200_e200.c b/firmware/target/arm/sandisk/power-c200_e200.c
index 910c3aaead..8745aa3fb6 100644
--- a/firmware/target/arm/sandisk/power-c200_e200.c
+++ b/firmware/target/arm/sandisk/power-c200_e200.c
@@ -85,7 +85,7 @@ bool tuner_power_nolock(bool status)
 #if defined(SANSA_E200)
             outl(inl(0x70000084) | 0x1, 0x70000084);
 #else /* SANSA_C200 */
-            DEV_INIT &= ~0x800;
+            DEV_INIT2 &= ~0x800;
 #endif
             udelay(5);
 
@@ -120,7 +120,7 @@ bool tuner_power_nolock(bool status)
 #if defined (SANSA_E200)
             outl(inl(0x70000084) & ~0x1, 0x70000084);
 #else
-            DEV_INIT |= 0x800;
+            DEV_INIT2 |= 0x800;
 #endif
         }
 
diff --git a/firmware/target/arm/sandisk/sansa-c200/lcd-c200.c b/firmware/target/arm/sandisk/sansa-c200/lcd-c200.c
index 24a7585508..5975ab159d 100644
--- a/firmware/target/arm/sandisk/sansa-c200/lcd-c200.c
+++ b/firmware/target/arm/sandisk/sansa-c200/lcd-c200.c
@@ -88,7 +88,7 @@ void lcd_init_device(void)
     outl(inl(0x70000010) & ~0xfc000000, 0x70000010);
     outl(inl(0x70000010), 0x70000010);
 
-    DEV_INIT &= ~0x400;
+    DEV_INIT2 &= ~0x400;
     udelay(10000);
     
     LCD1_CONTROL &= ~0x4;
diff --git a/firmware/target/arm/sandisk/sansa-e200/lcd-e200.c b/firmware/target/arm/sandisk/sansa-e200/lcd-e200.c
index 41926bb885..bf1fcf9926 100644
--- a/firmware/target/arm/sandisk/sansa-e200/lcd-e200.c
+++ b/firmware/target/arm/sandisk/sansa-e200/lcd-e200.c
@@ -372,7 +372,7 @@ void lcd_init_device(void)
 /* Controller init */
     outl((inl(0x70000084) | (1 << 28)), 0x70000084);
     outl((inl(0x70000080) & ~(1 << 28)), 0x70000080);
-    outl(((inl(0x70000010) & (0x03ffffff)) | (0x15 << 26)), 0x70000010);
+    DEV_INIT1 = ( (DEV_INIT1 & 0x03ffffff) | (0x15 << 26) );
     outl(((inl(0x70000014) & (0x0fffffff)) | (0x5 << 28)), 0x70000014);
     outl((inl(0x70000020) & ~(0x3 << 10)), 0x70000020);
     DEV_EN |= DEV_LCD; /* Enable controller */
diff --git a/firmware/target/arm/system-pp502x.c b/firmware/target/arm/system-pp502x.c
index d24d19f747..0882d9f212 100644
--- a/firmware/target/arm/system-pp502x.c
+++ b/firmware/target/arm/system-pp502x.c
@@ -240,17 +240,17 @@ void system_init(void)
     {
 #if defined(SANSA_E200) || defined(SANSA_C200)
         /* Reset all devices */
-        DEV_OFF_MASK |= 0x20;
+        DEV_RS2 |= 0x20;
         DEV_RS = 0x3bfffef8;
-        DEV_OFF_MASK = -1;
+        DEV_RS2 = -1;
         DEV_RS = 0;
-        DEV_OFF_MASK = 0;
+        DEV_RS2 = 0;
  #elif defined (IRIVER_H10)
         DEV_RS = 0x3ffffef8;
-        DEV_OFF_MASK = -1;
+        DEV_RS2 = -1;
         outl(inl(0x70000024) | 0xc0, 0x70000024);
         DEV_RS = 0;
-        DEV_OFF_MASK = 0;
+        DEV_RS2 = 0;
 #endif
 
 #if !defined(SANSA_E200) && !defined(SANSA_C200)
@@ -289,7 +289,7 @@ void system_init(void)
         outl(inl(0x6000a000) | 0x80000000, 0x6000a000); /* Init DMA controller? */
 #endif 
 
-        DEV_INIT |= 1 << 30; /* enable PLL power */
+        DEV_INIT2 |= 1 << 30; /* enable PLL power */
 
 #ifdef HAVE_ADJUSTABLE_CPU_FREQ
 #if NUM_CORES > 1
diff --git a/firmware/target/arm/usb-fw-pp502x.c b/firmware/target/arm/usb-fw-pp502x.c
index 792a1b0131..7d197f03b8 100644
--- a/firmware/target/arm/usb-fw-pp502x.c
+++ b/firmware/target/arm/usb-fw-pp502x.c
@@ -44,7 +44,7 @@ void usb_init_device(void)
     DEV_RS |= DEV_USB; /* reset usb start */  
     DEV_RS &=~DEV_USB;/* reset usb end */  
 
-    DEV_INIT |= INIT_USB;
+    DEV_INIT2 |= INIT_USB;
     while ((inl(0x70000028) & 0x80) == 0);
 
     UDC_PORTSC1 |= PORTSCX_PORT_RESET;  
@@ -70,7 +70,7 @@ void usb_init_device(void)
 
     /* Note from IPL source (referring to next 5 lines of code:  
        THIS NEEDS TO BE CHANGED ONCE THERE IS KERNEL USB */  
-    DEV_INIT |= INIT_USB;
+    DEV_INIT2 |= INIT_USB;
     DEV_EN |= DEV_USB;
     while ((inl(0x70000028) & 0x80) == 0);
     outl(inl(0x70000028) | 0x2, 0x70000028);
diff --git a/firmware/target/arm/wmcodec-pp.c b/firmware/target/arm/wmcodec-pp.c
index a2c83f33b3..3dd00695ae 100644
--- a/firmware/target/arm/wmcodec-pp.c
+++ b/firmware/target/arm/wmcodec-pp.c
@@ -46,7 +46,7 @@ void audiohw_init(void) {
 
 #ifdef CPU_PP502x
     /* normal outputs for CDI and I2S pin groups */
-    DEV_INIT &= ~0x300;
+    DEV_INIT2 &= ~0x300;
 
     /*mini2?*/
     outl(inl(0x70000010) & ~0x3000000, 0x70000010);