1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
|
/*
* descriptions for simple tuners.
*/
#ifndef __TUNER_TYPES_H__
#define __TUNER_TYPES_H__
enum param_type {
TUNER_PARAM_TYPE_RADIO,
TUNER_PARAM_TYPE_PAL,
TUNER_PARAM_TYPE_SECAM,
TUNER_PARAM_TYPE_NTSC,
TUNER_PARAM_TYPE_DIGITAL,
};
struct tuner_range {
unsigned short limit;
unsigned char config;
unsigned char cb;
};
struct tuner_params {
enum param_type type;
/* Many Philips based tuners have a comment like this in their
* datasheet:
*
* For channel selection involving band switching, and to ensure
* smooth tuning to the desired channel without causing
* unnecessary charge pump action, it is recommended to consider
* the difference between wanted channel frequency and the
* current channel frequency. Unnecessary charge pump action
* will result in very low tuning voltage which may drive the
* oscillator to extreme conditions.
*
* Set cb_first_if_lower_freq to 1, if this check is
* required for this tuner.
*
* I tested this for PAL by first setting the TV frequency to
* 203 MHz and then switching to 96.6 MHz FM radio. The result was
* static unless the control byte was sent first.
*/
unsigned int cb_first_if_lower_freq:1;
/* Set to 1 if this tuner uses a tda9887 */
unsigned int has_tda9887:1;
/* Many Philips tuners use tda9887 PORT1 to select the FM radio
sensitivity. If this setting is 1, then set PORT1 to 1 to
get proper FM reception. */
unsigned int port1_fm_high_sensitivity:1;
/* Some Philips tuners use tda9887 PORT2 to select the FM radio
sensitivity. If this setting is 1, then set PORT2 to 1 to
get proper FM reception. */
unsigned int port2_fm_high_sensitivity:1;
/* Some Philips tuners use tda9887 cGainNormal to select the FM radio
sensitivity. If this setting is 1, e register will use cGainNormal
instead of cGainLow. */
unsigned int fm_gain_normal:1;
/* Most tuners with a tda9887 use QSS mode. Some (cheaper) tuners
use Intercarrier mode. If this setting is 1, then the tuner
needs to be set to intercarrier mode. */
unsigned int intercarrier_mode:1;
/* This setting sets the default value for PORT1.
0 means inactive, 1 means active. Note: the actual bit
value written to the tda9887 is inverted. So a 0 here
means a 1 in the B6 bit. */
unsigned int port1_active:1;
/* This setting sets the default value for PORT2.
0 means inactive, 1 means active. Note: the actual bit
value written to the tda9887 is inverted. So a 0 here
means a 1 in the B7 bit. */
unsigned int port2_active:1;
/* Sometimes PORT1 is inverted when the SECAM-L' standard is selected.
Set this bit to 1 if this is needed. */
unsigned int port1_invert_for_secam_lc:1;
/* Sometimes PORT2 is inverted when the SECAM-L' standard is selected.
Set this bit to 1 if this is needed. */
unsigned int port2_invert_for_secam_lc:1;
/* Some cards require PORT1 to be 1 for mono Radio FM and 0 for stereo. */
unsigned int port1_set_for_fm_mono:1;
/* Select 18% (or according to datasheet 0%) L standard PLL gating,
vs the driver default of 36%. */
unsigned int default_pll_gating_18:1;
/* IF to use in radio mode. Tuners with a separate radio IF filter
seem to use 10.7, while those without use 33.3 for PAL/SECAM tuners
and 41.3 for NTSC tuners. 0 = 10.7, 1 = 33.3, 2 = 41.3 */
unsigned int radio_if:2;
/* Default tda9887 TOP value in dB for the low band. Default is 0.
Range: -16:+15 */
signed int default_top_low:5;
/* Default tda9887 TOP value in dB for the mid band. Default is 0.
Range: -16:+15 */
signed int default_top_mid:5;
/* Default tda9887 TOP value in dB for the high band. Default is 0.
Range: -16:+15 */
signed int default_top_high:5;
/* Default tda9887 TOP value in dB for SECAM-L/L' for the low band.
Default is 0. Several tuners require a different TOP value for
the SECAM-L/L' standards. Range: -16:+15 */
signed int default_top_secam_low:5;
/* Default tda9887 TOP value in dB for SECAM-L/L' for the mid band.
Default is 0. Several tuners require a different TOP value for
the SECAM-L/L' standards. Range: -16:+15 */
signed int default_top_secam_mid:5;
/* Default tda9887 TOP value in dB for SECAM-L/L' for the high band.
Default is 0. Several tuners require a different TOP value for
the SECAM-L/L' standards. Range: -16:+15 */
signed int default_top_secam_high:5;
u16 iffreq;
unsigned int count;
struct tuner_range *ranges;
};
struct tunertype {
char *name;
unsigned int count;
struct tuner_params *params;
u16 min;
u16 max;
u16 stepsize;
u8 *initdata;
u8 *sleepdata;
};
extern struct tunertype tuners[];
extern unsigned const int tuner_count;
#endif
|
