blob: 1f15e1fb1ab224b6ed0c925463d9e9fed30c0da2 (
plain)
1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
|
config ATH6K_LEGACY
tristate "Atheros AR6003 support (non mac80211)"
depends on MMC && WLAN
select WIRELESS_EXT
select WEXT_PRIV
help
This module adds support for wireless adapters based on Atheros AR6003 chipset running over SDIO. If you choose to build it as a module, it will be called ath6kl. Pls note that AR6002 and AR6001 are not supported by this driver.
choice
prompt "AR6003 Board Data Configuration"
depends on ATH6K_LEGACY
default AR600x_SD31_XXX
help
Select the appropriate board data template from the list below that matches your AR6003 based reference design.
config AR600x_SD31_XXX
bool "SD31-xxx"
help
Board Data file for a standard SD31 reference design (File: bdata.SD31.bin)
config AR600x_WB31_XXX
bool "WB31-xxx"
help
Board Data file for a standard WB31 (BT/WiFi) reference design (File: bdata.WB31.bin)
config AR600x_SD32_XXX
bool "SD32-xxx"
help
Board Data file for a standard SD32 (5GHz) reference design (File: bdata.SD32.bin)
config AR600x_CUSTOM_XXX
bool "CUSTOM-xxx"
help
Board Data file for a custom reference design (File: should be named as bdata.CUSTOM.bin)
endchoice
config ATH6KL_ENABLE_COEXISTENCE
bool "BT Coexistence support"
depends on ATH6K_LEGACY
help
Enables WLAN/BT coexistence support. Select the apprpriate configuration from below.
choice
prompt "Front-End Antenna Configuration"
depends on ATH6KL_ENABLE_COEXISTENCE
default AR600x_DUAL_ANTENNA
help
Indicates the number of antennas being used by BT and WLAN. Select the appropriate configuration from the list below that matches your AR6003 based reference design.
config AR600x_DUAL_ANTENNA
bool "Dual Antenna"
help
Dual Antenna Design
config AR600x_SINGLE_ANTENNA
bool "Single Antenna"
help
Single Antenna Design
endchoice
choice
prompt "Collocated Bluetooth Type"
depends on ATH6KL_ENABLE_COEXISTENCE
default AR600x_BT_AR3001
help
Select the appropriate configuration from the list below that matches your AR6003 based reference design.
config AR600x_BT_QCOM
bool "Qualcomm BTS4020X"
help
Qualcomm BT (3 Wire PTA)
config AR600x_BT_CSR
bool "CSR BC06"
help
CSR BT (3 Wire PTA)
config AR600x_BT_AR3001
bool "Atheros AR3001"
help
Atheros BT (3 Wire PTA)
endchoice
config ATH6KL_HCI_BRIDGE
bool "HCI over SDIO support"
depends on ATH6K_LEGACY
help
Enables BT over SDIO. Applicable only for combo designs (eg: WB31)
config ATH6KL_CONFIG_GPIO_BT_RESET
bool "Configure BT Reset GPIO"
depends on ATH6KL_HCI_BRIDGE
help
Configure a WLAN GPIO for use with BT.
config AR600x_BT_RESET_PIN
int "GPIO"
depends on ATH6KL_CONFIG_GPIO_BT_RESET
default 22
help
WLAN GPIO to be used for resetting BT
config ATH6KL_HTC_RAW_INTERFACE
bool "RAW HTC support"
depends on ATH6K_LEGACY
help
Enables raw HTC interface. Allows application to directly talk to the HTC interface via the ioctl interface
config ATH6KL_VIRTUAL_SCATTER_GATHER
bool "Virtual Scatter-Gather support"
depends on ATH6K_LEGACY
help
Enables virtual scatter gather support for the hardware that does not support it natively.
config ATH6KL_SKIP_ABI_VERSION_CHECK
bool "Skip ABI version check support"
depends on ATH6K_LEGACY
help
Forces the driver to disable ABI version check. Caution: Incompatilbity between the host driver and target firmware may lead to unknown side effects.
config ATH6KL_BT_UART_FC_POLARITY
int "UART Flow Control Polarity"
depends on ATH6KL_LEGACY
default 0
help
Configures the polarity of UART Flow Control. A value of 0 implies active low and is the default setting. Set it to 1 for active high.
config ATH6KL_DEBUG
bool "Debug support"
depends on ATH6K_LEGACY
help
Enables debug support
config ATH6KL_ENABLE_HOST_DEBUG
bool "Host Debug support"
depends on ATH6KL_DEBUG
help
Enables debug support in the driver
config ATH6KL_ENABLE_TARGET_DEBUG_PRINTS
bool "Target Debug support - Enable UART prints"
depends on ATH6KL_DEBUG
help
Enables uart prints
config AR600x_DEBUG_UART_TX_PIN
int "GPIO"
depends on ATH6KL_ENABLE_TARGET_DEBUG_PRINTS
default 8
help
WLAN GPIO to be used for Debug UART (Tx)
config ATH6KL_DISABLE_TARGET_DBGLOGS
bool "Target Debug support - Disable Debug logs"
depends on ATH6KL_DEBUG
help
Enables debug logs
|
