1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
|
#
# Coresight configuration
#
menuconfig CORESIGHT
bool "CoreSight Tracing Support"
select ARM_AMBA
select PERF_EVENTS
help
This framework provides a kernel interface for the CoreSight debug
and trace drivers to register themselves with. It's intended to build
a topological view of the CoreSight components based on a DT
specification and configure the right series of components when a
trace source gets enabled.
if CORESIGHT
config CORESIGHT_LINKS_AND_SINKS
bool "CoreSight Link and Sink drivers"
help
This enables support for CoreSight link and sink drivers that are
responsible for transporting and collecting the trace data
respectively. Link and sinks are dynamically aggregated with a trace
entity at run time to form a complete trace path.
config CORESIGHT_LINK_AND_SINK_TMC
bool "Coresight generic TMC driver"
depends on CORESIGHT_LINKS_AND_SINKS
help
This enables support for the Trace Memory Controller driver.
Depending on its configuration the device can act as a link (embedded
trace router - ETR) or sink (embedded trace FIFO). The driver
complies with the generic implementation of the component without
special enhancement or added features.
config CORESIGHT_CATU
bool "Coresight Address Translation Unit (CATU) driver"
depends on CORESIGHT_LINK_AND_SINK_TMC
help
Enable support for the Coresight Address Translation Unit (CATU).
CATU supports a scatter gather table of 4K pages, with forward/backward
lookup. CATU helps TMC ETR to use a large physically non-contiguous trace
buffer by translating the addresses used by ETR to the physical address
by looking up the provided table. CATU can also be used in pass-through
mode where the address is not translated.
config CORESIGHT_SINK_TPIU
bool "Coresight generic TPIU driver"
depends on CORESIGHT_LINKS_AND_SINKS
help
This enables support for the Trace Port Interface Unit driver,
responsible for bridging the gap between the on-chip coresight
components and a trace for bridging the gap between the on-chip
coresight components and a trace port collection engine, typically
connected to an external host for use case capturing more traces than
the on-board coresight memory can handle.
config CORESIGHT_SINK_ETBV10
bool "Coresight ETBv1.0 driver"
depends on CORESIGHT_LINKS_AND_SINKS
help
This enables support for the Embedded Trace Buffer version 1.0 driver
that complies with the generic implementation of the component without
special enhancement or added features.
config CORESIGHT_SOURCE_ETM3X
bool "CoreSight Embedded Trace Macrocell 3.x driver"
depends on !ARM64
select CORESIGHT_LINKS_AND_SINKS
help
This driver provides support for processor ETM3.x and PTM1.x modules,
which allows tracing the instructions that a processor is executing
This is primarily useful for instruction level tracing. Depending
the ETM version data tracing may also be available.
config CORESIGHT_SOURCE_ETM4X
bool "CoreSight Embedded Trace Macrocell 4.x driver"
depends on ARM64
select CORESIGHT_LINKS_AND_SINKS
help
This driver provides support for the ETM4.x tracer module, tracing the
instructions that a processor is executing. This is primarily useful
for instruction level tracing. Depending on the implemented version
data tracing may also be available.
config CORESIGHT_DYNAMIC_REPLICATOR
bool "CoreSight Programmable Replicator driver"
depends on CORESIGHT_LINKS_AND_SINKS
help
This enables support for dynamic CoreSight replicator link driver.
The programmable ATB replicator allows independent filtering of the
trace data based on the traceid.
config CORESIGHT_STM
bool "CoreSight System Trace Macrocell driver"
depends on (ARM && !(CPU_32v3 || CPU_32v4 || CPU_32v4T)) || ARM64
select CORESIGHT_LINKS_AND_SINKS
select STM
help
This driver provides support for hardware assisted software
instrumentation based tracing. This is primarily used for
logging useful software events or data coming from various entities
in the system, possibly running different OSs
config CORESIGHT_CPU_DEBUG
tristate "CoreSight CPU Debug driver"
depends on ARM || ARM64
depends on DEBUG_FS
help
This driver provides support for coresight debugging module. This
is primarily used to dump sample-based profiling registers when
system triggers panic, the driver will parse context registers so
can quickly get to know program counter (PC), secure state,
exception level, etc. Before use debugging functionality, platform
needs to ensure the clock domain and power domain are enabled
properly, please refer Documentation/trace/coresight-cpu-debug.txt
for detailed description and the example for usage.
endif
|
