1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
|
* Qualcomm NAND controller
Required properties:
- compatible: must be one of the following:
* "qcom,ipq806x-nand" - for EBI2 NAND controller being used in IPQ806x
SoC and it uses ADM DMA
* "qcom,ipq4019-nand" - for QPIC NAND controller v1.4.0 being used in
IPQ4019 SoC and it uses BAM DMA
* "qcom,ipq8074-nand" - for QPIC NAND controller v1.5.0 being used in
IPQ8074 SoC and it uses BAM DMA
- reg: MMIO address range
- clocks: must contain core clock and always on clock
- clock-names: must contain "core" for the core clock and "aon" for the
always on clock
EBI2 specific properties:
- dmas: DMA specifier, consisting of a phandle to the ADM DMA
controller node and the channel number to be used for
NAND. Refer to dma.txt and qcom_adm.txt for more details
- dma-names: must be "rxtx"
- qcom,cmd-crci: must contain the ADM command type CRCI block instance
number specified for the NAND controller on the given
platform
- qcom,data-crci: must contain the ADM data type CRCI block instance
number specified for the NAND controller on the given
platform
QPIC specific properties:
- dmas: DMA specifier, consisting of a phandle to the BAM DMA
and the channel number to be used for NAND. Refer to
dma.txt, qcom_bam_dma.txt for more details
- dma-names: must contain all 3 channel names : "tx", "rx", "cmd"
- #address-cells: <1> - subnodes give the chip-select number
- #size-cells: <0>
* NAND chip-select
Each controller may contain one or more subnodes to represent enabled
chip-selects which (may) contain NAND flash chips. Their properties are as
follows.
Required properties:
- reg: a single integer representing the chip-select
number (e.g., 0, 1, 2, etc.)
- #address-cells: see partition.txt
- #size-cells: see partition.txt
- nand-ecc-strength: see nand.txt
- nand-ecc-step-size: must be 512. see nand.txt for more details.
Optional properties:
- nand-bus-width: see nand.txt
Each nandcs device node may optionally contain a 'partitions' sub-node, which
further contains sub-nodes describing the flash partition mapping. See
partition.txt for more detail.
Example:
nand-controller@1ac00000 {
compatible = "qcom,ipq806x-nand";
reg = <0x1ac00000 0x800>;
clocks = <&gcc EBI2_CLK>,
<&gcc EBI2_AON_CLK>;
clock-names = "core", "aon";
dmas = <&adm_dma 3>;
dma-names = "rxtx";
qcom,cmd-crci = <15>;
qcom,data-crci = <3>;
#address-cells = <1>;
#size-cells = <0>;
nand@0 {
reg = <0>;
nand-ecc-strength = <4>;
nand-ecc-step-size = <512>;
nand-bus-width = <8>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "boot-nand";
reg = <0 0x58a0000>;
};
partition@58a0000 {
label = "fs-nand";
reg = <0x58a0000 0x4000000>;
};
};
};
};
nand-controller@79b0000 {
compatible = "qcom,ipq4019-nand";
reg = <0x79b0000 0x1000>;
clocks = <&gcc GCC_QPIC_CLK>,
<&gcc GCC_QPIC_AHB_CLK>;
clock-names = "core", "aon";
dmas = <&qpicbam 0>,
<&qpicbam 1>,
<&qpicbam 2>;
dma-names = "tx", "rx", "cmd";
#address-cells = <1>;
#size-cells = <0>;
nand@0 {
reg = <0>;
nand-ecc-strength = <4>;
nand-ecc-step-size = <512>;
nand-bus-width = <8>;
partitions {
compatible = "fixed-partitions";
#address-cells = <1>;
#size-cells = <1>;
partition@0 {
label = "boot-nand";
reg = <0 0x58a0000>;
};
partition@58a0000 {
label = "fs-nand";
reg = <0x58a0000 0x4000000>;
};
};
};
};
|
