1
2
3
4
5
6
7
8
9
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
56
57
58
59
60
61
62
63
64
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
97
98
99
100
101
102
103
104
105
106
107
108
109
110
111
112
113
114
115
116
117
118
119
120
121
122
123
124
125
126
127
128
129
130
131
132
133
134
135
136
137
138
139
140
141
142
143
144
145
146
147
148
149
150
151
152
153
154
155
156
157
158
159
160
161
162
163
164
165
|
Broadcom VC4 (VideoCore4) GPU
The VC4 device present on the Raspberry Pi includes a display system
with HDMI output and the HVS (Hardware Video Scaler) for compositing
display planes.
Required properties for VC4:
- compatible: Should be "brcm,bcm2835-vc4"
Required properties for Pixel Valve:
- compatible: Should be one of "brcm,bcm2835-pixelvalve0",
"brcm,bcm2835-pixelvalve1", or "brcm,bcm2835-pixelvalve2"
- reg: Physical base address and length of the PV's registers
- interrupts: The interrupt number
See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
Required properties for HVS:
- compatible: Should be "brcm,bcm2835-hvs"
- reg: Physical base address and length of the HVS's registers
- interrupts: The interrupt number
See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
Required properties for HDMI
- compatible: Should be "brcm,bcm2835-hdmi"
- reg: Physical base address and length of the two register ranges
("HDMI" and "HD", in that order)
- interrupts: The interrupt numbers
See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
- ddc: phandle of the I2C controller used for DDC EDID probing
- clocks: a) hdmi: The HDMI state machine clock
b) pixel: The pixel clock.
Optional properties for HDMI:
- hpd-gpios: The GPIO pin for HDMI hotplug detect (if it doesn't appear
as an interrupt/status bit in the HDMI controller
itself). See bindings/pinctrl/brcm,bcm2835-gpio.txt
- dmas: Should contain one entry pointing to the DMA channel used to
transfer audio data
- dma-names: Should contain "audio-rx"
Required properties for DPI:
- compatible: Should be "brcm,bcm2835-dpi"
- reg: Physical base address and length of the registers
- clocks: a) core: The core clock the unit runs on
b) pixel: The pixel clock that feeds the pixelvalve
- port: Port node with a single endpoint connecting to the panel
device, as defined in [1]
Required properties for VEC:
- compatible: Should be "brcm,bcm2835-vec"
- reg: Physical base address and length of the registers
- clocks: The core clock the unit runs on
- interrupts: The interrupt number
See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
Required properties for V3D:
- compatible: Should be "brcm,bcm2835-v3d"
- reg: Physical base address and length of the V3D's registers
- interrupts: The interrupt number
See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
Required properties for DSI:
- compatible: Should be "brcm,bcm2835-dsi0" or "brcm,bcm2835-dsi1"
- reg: Physical base address and length of the DSI block's registers
- interrupts: The interrupt number
See bindings/interrupt-controller/brcm,bcm2835-armctrl-ic.txt
- clocks: a) phy: The DSI PLL clock feeding the DSI analog PHY
b) escape: The DSI ESC clock from CPRMAN
c) pixel: The DSI pixel clock from CPRMAN
- clock-output-names:
The 3 clocks output from the DSI analog PHY: dsi[01]_byte,
dsi[01]_ddr2, and dsi[01]_ddr
[1] Documentation/devicetree/bindings/media/video-interfaces.txt
Example:
pixelvalve@7e807000 {
compatible = "brcm,bcm2835-pixelvalve2";
reg = <0x7e807000 0x100>;
interrupts = <2 10>; /* pixelvalve */
};
hvs@7e400000 {
compatible = "brcm,bcm2835-hvs";
reg = <0x7e400000 0x6000>;
interrupts = <2 1>;
};
hdmi: hdmi@7e902000 {
compatible = "brcm,bcm2835-hdmi";
reg = <0x7e902000 0x600>,
<0x7e808000 0x100>;
interrupts = <2 8>, <2 9>;
ddc = <&i2c2>;
hpd-gpios = <&gpio 46 GPIO_ACTIVE_HIGH>;
clocks = <&clocks BCM2835_PLLH_PIX>,
<&clocks BCM2835_CLOCK_HSM>;
clock-names = "pixel", "hdmi";
};
dpi: dpi@7e208000 {
compatible = "brcm,bcm2835-dpi";
reg = <0x7e208000 0x8c>;
clocks = <&clocks BCM2835_CLOCK_VPU>,
<&clocks BCM2835_CLOCK_DPI>;
clock-names = "core", "pixel";
#address-cells = <1>;
#size-cells = <0>;
port {
dpi_out: endpoint@0 {
remote-endpoint = <&panel_in>;
};
};
};
dsi1: dsi@7e700000 {
compatible = "brcm,bcm2835-dsi1";
reg = <0x7e700000 0x8c>;
interrupts = <2 12>;
#address-cells = <1>;
#size-cells = <0>;
#clock-cells = <1>;
clocks = <&clocks BCM2835_PLLD_DSI1>,
<&clocks BCM2835_CLOCK_DSI1E>,
<&clocks BCM2835_CLOCK_DSI1P>;
clock-names = "phy", "escape", "pixel";
clock-output-names = "dsi1_byte", "dsi1_ddr2", "dsi1_ddr";
pitouchscreen: panel@0 {
compatible = "raspberrypi,touchscreen";
reg = <0>;
<...>
};
};
vec: vec@7e806000 {
compatible = "brcm,bcm2835-vec";
reg = <0x7e806000 0x1000>;
clocks = <&clocks BCM2835_CLOCK_VEC>;
interrupts = <2 27>;
};
v3d: v3d@7ec00000 {
compatible = "brcm,bcm2835-v3d";
reg = <0x7ec00000 0x1000>;
interrupts = <1 10>;
};
vc4: gpu {
compatible = "brcm,bcm2835-vc4";
};
panel: panel {
compatible = "ontat,yx700wv03", "simple-panel";
port {
panel_in: endpoint {
remote-endpoint = <&dpi_out>;
};
};
};
|
