summaryrefslogtreecommitdiff
path: root/drivers
AgeCommit message (Collapse)Author
2016-02-25qed: Prevent probe on previous errorYuval Mintz
Don't allow driver to probe on an adapter at a failed state; Gracefully block the probe instead. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25qed: add MODULE_FIRMWARE()Yuval Mintz
Module is using a binary firmware file and so should be marked as such. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25qede: Don't report link change needlesslyYuval Mintz
There are several corner cases where driver might get a 2nd notification about the same link change. Don't log any additional changes if the physical carrier is already reported as it should. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25qede: Linearize SKBs when neededYuval Mintz
There's a corner-case in HW where an SKB queued for transmission that contains too many frags will cause FW to assert. This patch solves this by linearizing the SKB if necessary. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25qede: Change pci DID for 10g deviceYuval Mintz
The device ID for the 10g module has changed. Populate the pci_ids table accordingly. Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25netxen: Use kobj_to_dev()Amitoj Kaur Chawla
Introduce the use of kobj_to_dev() helper function instead of open coding it with container_of() The Coccinelle semantic patch used to make this change is as follows: //<smpl> @@ expression a; symbol kobj; @@ - container_of(a, struct device, kobj) + kobj_to_dev(a) //</smpl> Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-253c59x: Use setup_timer()Amitoj Kaur Chawla
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. The Coccinelle semantic patch that fixes this problem is as follows: // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); ... -t.data = d; -t.function = f; // </smpl> Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25forcedeth: Use setup_timer()Amitoj Kaur Chawla
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. The Coccinelle semantic patch that fixes this problem is as follows: // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.data = d; -t.function = f; // </smpl> Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25net: tulip: Use setup_timer()Amitoj Kaur Chawla
Convert a call to init_timer and accompanying intializations of the timer's data and function fields to a call to setup_timer. The Coccinelle semantic patch that fixes this problem is as follows: // <smpl> @@ expression t,f,d; @@ -init_timer(&t); +setup_timer(&t,f,d); -t.data = d; -t.function = f; // </smpl> Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25gianfar: fix endianness for hardware timestampYangbo Lu
Fix endianness for the 64-bit hardware timestamp value with be64_to_cpu to support both PowerPC platforms and ARM platforms. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25gianfar_ptp: replace get_of_u32 with of_property_read_u32Yangbo Lu
Replace get_of_u32 with standard helper function of_property_read_u32 since the latter can process cpu endianness. Signed-off-by: Yangbo Lu <yangbo.lu@nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25phy: marvell: Fix 88E1510 initializationClemens Gruber
A bug was introduced in the merge commit b633353115e3 ("Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net") The generic marvell_config_init (and therefore marvell_of_reg_init) is not called anymore for the Marvell 88E1510 (in net-next). This patch calls marvell_config_init and moves the specific init function for the 88E1510 below the marvell_config_init function to avoid adding a function predeclaration. Signed-off-by: Clemens Gruber <clemens.gruber@pqgruber.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25net: dsa: mv88e6xxx: implement port_vlan_dumpVivien Didelot
Remove the port_pvid_get and vlan_getnext functions in favor of a simpler mv88e6xxx_port_vlan_dump function. Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25vxlan: simplify metadata_dst usage in vxlan_rcvJiri Benc
Now when the packet is scrubbed early, the metadata_dst can be assigned to the skb as soon as it is allocated. This simplifies the error cleanup path, as the dst will be freed by kfree_skb. It is also not necessary to pass it as a parameter to functions anymore. Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25vxlan: consolidate rx handling to a single functionJiri Benc
Now when both vxlan_udp_encap_recv and vxlan_rcv are much shorter, combine them into a single function. Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25vxlan: move ECN decapsulation to a separate functionJiri Benc
It simplifies the vxlan_rcv function. Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25vxlan: move inner L2 header processing to a separate functionJiri Benc
This code will be different for VXLAN-GPE, so move it to a separate function. It will also make the rx path less spaghetti-like. Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-25vxlan: consolidate GBP handling even moreJiri Benc
Now when the packet is scrubbed early, skb->mark can be set in the GBP handling code. Signed-off-by: Jiri Benc <jbenc@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24ppp: clarify parsing of user supplied data in ppp_set_compress()Guillaume Nault
* Split big conditional statement. * Check (data.length <= CCP_MAX_OPTION_LENGTH) only once. * Don't read ccp_option[1] if not initialised. Reading uninitialised ccp_option[1] was harmless, because this could only happen when data.length was 0 or 1. So even then, we couldn't pass the (ccp_option[1] < 2 || ccp_option[1] > data.length) test anyway. Signed-off-by: Guillaume Nault <g.nault@alphalink.fr> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24bnx2x: add a separate GENEVE Kconfig symbolArnd Bergmann
When CONFIG_GENEVE is built as a loadable module, and bnx2x is built-in, we get this link error: drivers/net/built-in.o: In function `bnx2x_open': :(.text+0x33322): undefined reference to `geneve_get_rx_port' drivers/net/built-in.o: In function `bnx2x_sp_rtnl_task': :(.text+0x3e632): undefined reference to `geneve_get_rx_port' This avoids the problem by adding a separate Kconfig symbol named CONFIG_BNX2X_GENEVE that is only enabled when the code is reachable from the driver. This is the same trick that BNX2X does for VXLAN support, and is similar to how I40E handles both. Signed-off-by: Arnd Bergmann <arnd@arndb.de> Fixes: 883ce97d25b0 ("bnx2x: Add Geneve inner-RSS support") Acked-By: Yuval Mintz <Yuval.Mintz@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24igb: call ndo_stop() instead of dev_close() when running offline selftestStefan Assmann
Calling dev_close() causes IFF_UP to be cleared which will remove the interfaces routes and some addresses. That's probably not what the user intended when running the offline selftest. Besides this does not happen if the interface is brought down before the test, so the current behaviour is inconsistent. Instead call the net_device_ops ndo_stop function directly and avoid touching IFF_UP at all. Signed-off-by: Stefan Assmann <sassmann@kpanic.de> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24igb: Fix VLAN tag stripping on Intel i350Corinna Vinschen
Problem: When switching off VLAN offloading on an i350, the VLAN interface gets unusable. For testing, set up a VLAN on an i350 and some remote machine, e.g.: $ ip link add link eth0 name eth0.42 type vlan id 42 $ ip addr add 192.168.42.1/24 dev eth0.42 $ ip link set dev eth0.42 up Offloading is switched on by default: $ ethtool -k eth0 | grep vlan-offload rx-vlan-offload: on tx-vlan-offload: on $ ping -c 3 -I eth0.42 192.168.42.2 [...works as usual...] Now switch off VLAN offloading and try again: $ ethtool -K eth0 rxvlan off Actual changes: rx-vlan-offload: off tx-vlan-offload: off [requested on] $ ping -c 3 -I eth0.42 192.168.42.2 PING 192.168.42.2 (192.168.42.2) from 192.168.42.1 eth0.42: 56(84) bytes of da ta. --- 192.168.42.2 ping statistics --- 3 packets transmitted, 0 received, 100% packet loss, time 1999ms I can only reproduce it on an i350, the above works fine on a 82580. While inspecting the igb source, I came across the code in igb_set_vmolr which sets the E1000_VMOLR_STRVLAN/E1000_DVMOLR_STRVLAN flags once and for all, and in all of the igb code there's no other place where the STRVLAN is set or cleared. Thus, VLAN stripping is enabled in igb unconditionally, independently of the offloading setting. I compared that to the latest Intel igb-5.3.3.5 driver from http://sourceforge.net/projects/e1000/ which in fact sets and clears the STRVLAN flag independently from igb_set_vmolr in its own function igb_set_vf_vlan_strip, depending on the vlan settings. So I included the STRVLAN handling from the igb-5.3.3.5 driver into our current igb driver and tested the above scenario again. This time ping still works after switching off VLAN offloading. Tested on i350, with and without addtional VFs, as well as on 82580 successfully. Signed-off-by: Corinna Vinschen <vinschen@redhat.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24igbvf: remove "link is Up" message when registering mcast addressJon Maxwell
A similar issue was addressed a few years ago in the following thread: http://www.spinics.net/lists/netdev/msg245877.html At that time there were concerns that removing this statement may cause other side effects. However the submitter addressed those concerns. But the dialogue went cold. We have a new case where a customers application is registering and un-registering multicast addresses every few seconds. This is leading to many "Link is Up" messages in the logs as a result of the "netif_carrier_off(netdev)" statement called by igbvf_msix_other(). Also on some kernels it is interfering with the bonding driver causing it to failover and subsequently affecting connectivity. The Sourgeforge driver does not make this call and is therefore not affected. If there were any side effects I would expect that driver to also be affected. I have tested re-loading the igbvf driver and downing the adapter with the PF entity on the host where the VM has this patch. When I bring it back up again connectivity is restored as expected. Therefore I request that this patch gets submitted. Signed-off-by: Jon Maxwell <jmaxwell37@gmail.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24igbvf: Add support for generic Tx checksumsAlexander Duyck
This patch adds support for generic Tx checksums to the igbvf driver. It turns out this is actually pretty easy after going over the datasheet as we were doing a number of steps we didn't need to. In order to perform a Tx checksum for an L4 header we need to fill in the following fields in the Tx descriptor: MACLEN (maximum of 127), retrieved from: skb_network_offset() IPLEN (maximum of 511), retrieved from: skb_checksum_start_offset() - skb_network_offset() TUCMD.L4T indicates offset and if checksum or crc32c, based on: skb->csum_offset The added advantage to doing this is that we can support inner checksum offloads for tunnels and MPLS while still being able to transparently insert VLAN tags. I also took the opportunity to clean-up many of the feature flag configuration bits to make them a bit more consistent between drivers. In the case of the VF drivers this meant adding support for SCTP CRCs, and inner checksum offloads for MPLS and various tunnel types. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24igb: Add support for generic Tx checksumsAlexander Duyck
This patch adds support for generic Tx checksums to the igb driver. It turns out this is actually pretty easy after going over the datasheet as we were doing a number of steps we didn't need to. In order to perform a Tx checksum for an L4 header we need to fill in the following fields in the Tx descriptor: MACLEN (maximum of 127), retrieved from: skb_network_offset() IPLEN (maximum of 511), retrieved from: skb_checksum_start_offset() - skb_network_offset() TUCMD.L4T indicates offset and if checksum or crc32c, based on: skb->csum_offset The added advantage to doing this is that we can support inner checksum offloads for tunnels and MPLS while still being able to transparently insert VLAN tags. I also took the opportunity to clean-up many of the feature flag configuration bits to make them a bit more consistent between drivers. Signed-off-by: Alexander Duyck <aduyck@mirantis.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24igb: rename igb define to be more genericTodd Fujinaka
E1000_MRQC_ENABLE_RSS_4Q enables 4 and 8 queues depending on the part so rename to be generic. Similarly, E1000_MRQC_ENABLE_VMDQ_RSS_2Q has no numeric meaning so rename to be more generic. Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24igb: add conditions for I210 to generate periodic clock outputRoland Hii
In general case the maximum supported half cycle time of the synchronized output clock is 70msec. Slower half cycle time than 70msec can be programmed also as long as the output clock is synchronized to whole seconds, useful specifically for generating a 1Hz clock. Permitted values for the clock half cycle time are: 125,000,000 decimal, 250,000,000 decimal and 500,000,000 decimal (equals to 125msec, 250msec and 500msec respectively). Before this patch, only the half cycle time of less than or equal to 70msec uses the I210 clock output function. This patch adds additional conditions when half cycle time is equal to 125msec or 250msec or 500msec to use clock output function. Under other conditions, interrupt driven target time output events method is still used to generate the desired clock output. Signed-off-by: Roland Hii <roland.king.guan.hii@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24igb: enable WoL for OEM devices regardless of EEPROM settingTodd Fujinaka
Override EEPROM settings for specific OEM devices. Signed-off-by: Todd Fujinaka <todd.fujinaka@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24igb: constify e1000_phy_operations structureJulia Lawall
This e1000_phy_operations structure is never modified, so declare it as const. Other structures of this type are already const. Done with the help of Coccinelle. Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24igb: When GbE link up, wait for Remote receiver status conditionTakuma Ueba
I210 device IPv6 autoconf test sometimes fails, because DAD NS for link-local is not transmitted. This packet is silently dropped. This problem is seen only GbE environment. igb_watchdog_task link up detection continues to the following process. The following cases are observed: 1.PHY 1000BASE-T Status Register Remote receiver status bit is NG. (NG status becomes OK after about 200 - 700ms) 2.In this case, the transfer packet is silently dropped. 1000BASE-T Status register [Expected]: 0x3800 or 0x7800 [problem occurred]: 0x2800 or 0x6800 Frequency of occurrence: approx 1/10 - 1/40 observed In order to avoid this problem, wait until 1000BASE-T Status register "Remote receiver status OK" After applying this patch, at least 400 runs succeed with no problems. Signed-off-by: Takuma Ueba <t.ueba11@gmail.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24e1000e: Initial support for KabeLakeRaanan Avargil
i219 (4) and i219 (5) are the next LOM generations that will be available on the next Intel platform (KabeLake). This patch provides the initial support for the devices. Signed-off-by: Raanan Avargil <raanan.avargil@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24e1000e: Clear ULP configuration register on ULP exitRaanan Avargil
There have been bugs caused by HW ULP configuration settings not being properly cleared after cable connect in V-Pro capable systems. This caused HW to get out of sync occasionally. The fix ensures that ULP settings are cleared in HW after LAN cable re-connect. Signed-off-by: Raanan Avargil <raanan.avargil@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24e1000e: Set HW FIFO minimum pointer gap for non-gig speedsRaanan Avargil
Based on feedback from HW team, the configured value of the internal PHY HW FIFO pointer gap was incorrect for non-gig speeds. This patch provides the correct configuration. Signed-off-by: Raanan Avargil <raanan.avargil@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24e1000e: Increase PHY PLL clock gate timingRaanan Avargil
Several packet loss issues were reported for which the root cause for them was an incorrect configuration of internal HW PHY clock gating mechanism by SW. This patch provides the correct mechanism. Signed-off-by: Raanan Avargil <raanan.avargil@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24e1000e: Increase ULP timerRaanan Avargil
Due to system level changes introduced in Skylake, ULP exit takes significantly longer to occur. Therefore, driver must wait longer for. Signed-off-by: Raanan Avargil <raanan.avargil@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2016-02-24gianfar: Remove redundant ops for do_tstamp from xmit()Claudiu Manoil
Timestamp BD status updates that can be merged into the same "do_tstamp" block, no need for extra save/restore to the BD area. The code is more readable too. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24gianfar: Use skb_frag_t pointers inside xmit()Claudiu Manoil
Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24gianfar: Map head TxBD firstClaudiu Manoil
Move the mapping of the head BD before the mapping of fragments. The TOE (h/w offload) decision logic block can be also moved up (as the TOE flag belongs to the head BD), resulting in more localized code (TOE logic vs BD mapping code blocks). Note that, for this h/w, the R (status) bit for the head BD of a S/G frame needs to be written last for a reliable transmission. For the fragmented skb case, a local variable is used to temporarily store the status info of the first BD, replacing a BD status read. A merge of 2 "if(do_tstamp)" blocks was also possible. Signed-off-by: Claudiu Manoil <claudiu.manoil@freescale.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24bgmac: support Ethernet device on BCM47094 SoCRafał Miłecki
It needs very similar workarounds to the one on BCM4707. It was tested on D-Link DIR-885L home router. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24be2net: Fix a UE caused by passing large frames to the ASICajit.khaparde@broadcom.com
In QnQ configurations like Flex-10 where the VLANs are inserted by the ASIC, on rare occasions the HW is encountering a scenario where the final frame length ends to be greater than what the ASIC can support. This is because when the TXULP pulls the TX WRB to check the length of the frame to be transmitted it also adds the size of VLANs to be inserted by the HW to the length of the frame indicated in the WRB, which in some cases fails the range check. This causes a UE. Avoid this by trimming the skb length to accommodate the VLAN insertion. Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24be2net: Declare some u16 fields as u32 to improve performanceajit.khaparde@broadcom.com
When 16-bit integers are loaded on CPUs with high order native register sizes, the CPU could use some extra ops before using them. And currently some of the frequently used fields in the driver like the producer and consumer indices of the queues are declared as u16. This patch declares such fields as u32. With this change we see the 64-byte packets per second numbers improve by about 4%. Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24net/mlx5e: Add TX inner packet countersMatthew Finlay
Add TSO and TX checksum counters for tunneled, inner packets Signed-off-by: Matthew Finlay <matt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24net/mlx5e: Add TX stateless offloads for tunnelingMatthew Finlay
Add support for TSO and TX checksum when using hw assisted, tunneled offloads. Signed-off-by: Matthew Finlay <matt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24net/mlx5e: Add netdev support for VXLAN tunnelingMatthew Finlay
If a VXLAN udp dport is added to device it will: - Configure the hardware to offload the port (up to the max supported). - Advertise NETIF_F_GSO_UDP_TUNNEL and supported hw_enc_features. Signed-off-by: Matthew Finlay <matt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24net/mlx5e: Protect en header file from redefinitionsMatthew Finlay
add ifndef to en.h. needed for upcoming vxlan patchset. Signed-off-by: Matthew Finlay <matt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24net/mlx5e: Move to checksum completeMatthew Finlay
Use checksum complete for all IP packets, unless they are HW LRO, in which case, use checksum unnecessary. Signed-off-by: Matthew Finlay <matt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24net/mlx5e: Wake On LAN supportTariq Toukan
Implement set/get WOL by ethtool and added the needed device commands and structures to mlx5_ifc. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Rana Shahout <ranas@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24net/mlx5e: Implement DCBNL IEEE max rateTariq Toukan
Add support for DCBNL IEEE get/set max rate. Signed-off-by: Tariq Toukan <tariqt@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24net/mlx5e: Support DCBNL IEEE PFCAchiad Shochat
Implement the set/get DCBNL IEEE PFC callbacks. Signed-off-by: Achiad Shochat <achiad@mellanox.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2016-02-24net/mlx5e: Support DCBNL IEEE ETSSaeed Mahameed
Support the ndo_setup_tc callback and the needed methods for multi TC/UP support, and removed the default_vlan_prio from mlx5e_priv which is always 0, it was replaced with hardcoded "0" in the new select queue method. For that we now create MAX_NUM_TC num of TISs (one per prio) on netdevice creation instead of priv->params.num_tc which was always 1. So far each channel had a single TXQ, Now each channel has a TXQ per TC (Traffic Class). Added en_dcbnl.c which implements the set/get DCBNL IEEE ETS, set/get dcbx and registers the mlx5e dcbnl ops. We still use the kernel's default TXQ selection method to select the channel to transmit through but now we use our own method to select the TXQ inside the channel based on VLAN priority. In mlx5, as opposed to mlx4, tc group N gets lower priority than tc group N+1. CC: John Fastabend <john.fastabend@gmail.com> Signed-off-by: Saeed Mahameed <saeedm@mellanox.com> Signed-off-by: Rana Shahout <ranas@mellanox.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-14 22:27:10 +0000