| Age | Commit message (Collapse) | Author |
|---|
|
This attempts to fix a bug found with a serial port card which uses
an MCS9922 chip, one of the 4 models for which MSI-X interrupts are
currently supported. I don't possess such a card, and i'm not
experienced with the serial subsystem, so this patch is based on what
i think i found as a likely reason for failure, based on walking the
user who actually owns the card through some diagnostic.
The user who reported the problem finds the following in his dmesg
output for the relevant ttyS4 and ttyS5:
[ 0.580425] serial 0000:02:00.0: enabling device (0000 -> 0003)
[ 0.601448] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 125, base_baud = 115200) is a ST16650V2
[ 0.603089] serial 0000:02:00.1: enabling device (0000 -> 0003)
[ 0.624119] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 126, base_baud = 115200) is a ST16650V2
...
[ 6.323784] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
[ 6.324128] genirq: Flags mismatch irq 128. 00000080 (ttyS5) vs. 00000000 (xhci_hcd)
...
Output of setserial -a:
/dev/ttyS4, Line 4, UART: 16650V2, Port: 0x3010, IRQ: 127
Baud_base: 115200, close_delay: 50, divisor: 0
closing_wait: 3000
Flags: spd_normal skip_test
This suggests to me that the serial driver wants to register and share a
MSI/MSI-X irq 128 with the xhci_hcd driver, whereas the xhci driver does
not want to share the irq, as flags 0x00000080 (== IRQF_SHARED) from the
serial port driver means to share the irq, and this mismatch ends in some
failed irq init?
With this setup, data reception works very unreliable, with dropped data,
already at a transmission rate of only a 16 Bytes chunk every 1/120th of
a second, ie. 1920 Bytes/sec, presumably due to rx fifo overflow due to
mishandled or not used at all rx irq's?
See full discussion thread with attempted diagnosis at:
https://psychtoolbox.discourse.group/t/issues-with-iscan-serial-port-recording/3886
Disabling the use of MSI interrupts for the serial port pci card did
fix the reliability problems. The user executed the following sequence
of commands to achieve this:
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/unbind
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.0/msi_bus
echo 0 | sudo tee /sys/bus/pci/devices/0000:02:00.1/msi_bus
echo 0000:02:00.0 | sudo tee /sys/bus/pci/drivers/serial/bind
echo 0000:02:00.1 | sudo tee /sys/bus/pci/drivers/serial/bind
This resulted in the following log output:
[ 82.179021] pci 0000:02:00.0: MSI/MSI-X disallowed for future drivers
[ 87.003031] pci 0000:02:00.1: MSI/MSI-X disallowed for future drivers
[ 98.537010] 0000:02:00.0: ttyS4 at I/O 0x3010 (irq = 17, base_baud = 115200) is a ST16650V2
[ 103.648124] 0000:02:00.1: ttyS5 at I/O 0x3000 (irq = 18, base_baud = 115200) is a ST16650V2
This patch attempts to fix the problem by disabling irq sharing when
using MSI irq's. Note that all i know for sure is that disabling MSI
irq's fixed the problem for the user, so this patch could be wrong and
is untested. Please review with caution, keeping this in mind.
Fixes: 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support")
Cc: Ralf Ramsauer <ralf.ramsauer@oth-regensburg.de>
Cc: stable <stable@vger.kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Mario Kleiner <mario.kleiner.de@gmail.com>
Link: https://lore.kernel.org/r/20210729043306.18528-1-mario.kleiner.de@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix uart corruption issue when rx power off.
Add spin lock in mtk8250_dma_rx_complete function in APDMA mode.
when uart is used as a communication port with external device(GPS).
when external device(GPS) power off, the power of rx pin is also from
1.8v to 0v. Even if there is not any data in rx. But uart rx pin can
capture the data "0".
If uart don't receive any data in specified cycle, uart will generates
BI(Break interrupt) interrupt.
If external device(GPS) power off, we found that BI interrupt appeared
continuously and very frequently.
When uart interrupt type is BI, uart IRQ handler(8250 framwork
API:serial8250_handle_irq) will push data to tty buffer.
mtk8250_dma_rx_complete is a task of mtk_uart_apdma_rx_handler.
mtk8250_dma_rx_complete priority is lower than uart irq
handler(serial8250_handle_irq).
if we are in process of mtk8250_dma_rx_complete, uart appear BI
interrupt:1)serial8250_handle_irq will priority execution.2)it may cause
write tty buffer conflict in mtk8250_dma_rx_complete.
So the spin lock protect the rx receive data process is not break.
Signed-off-by: Zhiyong Tao <zhiyong.tao@mediatek.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210729084640.17613-2-zhiyong.tao@mediatek.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Patch e60c2991f18b make the lpuart32_get_mctrl always return 0, actually
this will break the functions of device which use flow control such as
Bluetooth.
For lpuart32 plaform, the hardware can handle the CTS automatically.
So we should set TIOCM_CTS active. Also need to set CAR and DSR active.
Patch has been tested on lpuart32 platforms such as imx8qm and imx8ulp.
Fixes: e60c2991f18b ("serial: fsl_lpuart: remove RTSCTS handling from get_mctrl()")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Sherry Sun <sherry.sun@nxp.com>
Link: https://lore.kernel.org/r/20210729083109.31541-1-sherry.sun@nxp.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Elkhart Lake UARTs are PCI enumerated Synopsys DesignWare v4.0+ UART
integrated with Intel iDMA 32-bit DMA controller. There is a specific
driver to handle them, i.e. 8250_lpss. Hence, disable 8250_pci
enumeration for these UARTs.
Fixes: 1b91d97c66ef ("serial: 8250_lpss: Add ->setup() for Elkhart Lake ports")
Fixes: 4f912b898dc2 ("serial: 8250_lpss: Enable HS UART on Elkhart Lake")
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210713101739.36962-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The 8250 handle_irq callback is not just called from the interrupt
handler but also from a timer callback when polling (e.g. for ports
without an interrupt line). Consequently the callback must explicitly
disable interrupts to avoid a potential deadlock with another interrupt
in polled mode.
Add back an irqrestore-version of the sysrq port-unlock helper and use
it in the 8250 callbacks that need it.
Fixes: 75f4e830fa9c ("serial: do not restore interrupt state in sysrq helper")
Cc: stable@vger.kernel.org # 5.13
Cc: Joel Stanley <joel@jms.id.au>
Cc: Andrew Jeffery <andrew@aj.id.au>
Reported-by: kernel test robot <oliver.sang@intel.com>
Signed-off-by: Johan Hovold <johan@kernel.org>
Link: https://lore.kernel.org/r/20210714080427.28164-1-johan@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Tegra serial driver always prints an error message when enabling the
FIFO for devices that have support for checking the FIFO enable status.
Fix this by displaying the error message, only when an error occurs.
Finally, update the error message to make it clear that enabling the
FIFO failed and display the error code.
Fixes: 222dcdff3405 ("serial: tegra: check for FIFO mode enabled status")
Cc: <stable@vger.kernel.org>
Acked-by: Thierry Reding <treding@nvidia.com>
Signed-off-by: Jon Hunter <jonathanh@nvidia.com>
Link: https://lore.kernel.org/r/20210630125643.264264-1-jonathanh@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Make sure only actual 8 bits of the IIR register are used in determining
the port type in `autoconfig'.
The `serial_in' port accessor returns the `unsigned int' type, meaning
that with UPIO_AU, UPIO_MEM16, UPIO_MEM32, and UPIO_MEM32BE access types
more than 8 bits of data are returned, of which the high order bits will
often come from bus lines that are left floating in the data phase. For
example with the MIPS Malta board's CBUS UART, where the registers are
aligned on 8-byte boundaries and which uses 32-bit accesses, data as
follows is returned:
YAMON> dump -32 0xbf000900 0x40
BF000900: 1F000942 1F000942 1F000900 1F000900 ...B...B........
BF000910: 1F000901 1F000901 1F000900 1F000900 ................
BF000920: 1F000900 1F000900 1F000960 1F000960 ...........`...`
BF000930: 1F000900 1F000900 1F0009FF 1F0009FF ................
YAMON>
Evidently high-order 24 bits return values previously driven in the
address phase (the 3 highest order address bits used with the command
above are masked out in the simple virtual address mapping used here and
come out at zeros on the external bus), a common scenario with bus lines
left floating, due to bus capacitance.
Consequently when the value of IIR, mapped at 0x1f000910, is retrieved
in `autoconfig', it comes out at 0x1f0009c1 and when it is right-shifted
by 6 and then assigned to 8-bit `scratch' variable, the value calculated
is 0x27, not one of 0, 1, 2, 3 expected in port type determination.
Fix the issue then, by assigning the value returned from `serial_in' to
`scratch' first, which masks out 24 high-order bits retrieved, and only
then right-shift the resulting 8-bit data quantity, producing the value
of 3 in this case, as expected. Fix the same issue in `serial_dl_read'.
The problem first appeared with Linux 2.6.9-rc3 which predates our repo
history, but the origin could be identified with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>
as commit e0d2356c0777 ("Merge with Linux 2.6.9-rc3."), where code in
`serial_in' was updated with this case:
+ case UPIO_MEM32:
+ return readl(up->port.membase + offset);
+
which made it produce results outside the unsigned 8-bit range for the
first time, though obviously it is system dependent what actual values
appear in the high order bits retrieved and it may well have been zeros
in the relevant positions with the system the change originally was
intended for. It is at that point that code in `autoconf' should have
been updated accordingly, but clearly it was overlooked.
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Cc: stable@vger.kernel.org # v2.6.12+
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106260516220.37803@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In one error case the clock may be left prepared and enabled.
Unprepare and disable clock in that case to balance state of
the hardware.
Fixes: d4d6f03c4fb3 ("serial: max310x: Try to get crystal clock rate from property")
Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210625153733.12911-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial updates from Greg KH:
"Here is the big set of tty and serial driver patches for 5.14-rc1.
A bit more than normal, but nothing major, lots of cleanups.
Highlights are:
- lots of tty api cleanups and mxser driver cleanups from Jiri
- build warning fixes
- various serial driver updates
- coding style cleanups
- various tty driver minor fixes and updates
- removal of broken and disable r3964 line discipline (finally!)
All of these have been in linux-next for a while with no reported
issues"
* tag 'tty-5.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty: (227 commits)
serial: mvebu-uart: remove unused member nb from struct mvebu_uart
arm64: dts: marvell: armada-37xx: Fix reg for standard variant of UART
dt-bindings: mvebu-uart: fix documentation
serial: mvebu-uart: correctly calculate minimal possible baudrate
serial: mvebu-uart: do not allow changing baudrate when uartclk is not available
serial: mvebu-uart: fix calculation of clock divisor
tty: make linux/tty_flip.h self-contained
serial: Prefer unsigned int to bare use of unsigned
serial: 8250: 8250_omap: Fix possible interrupt storm on K3 SoCs
serial: qcom_geni_serial: use DT aliases according to DT bindings
Revert "tty: serial: Add UART driver for Cortina-Access platform"
tty: serial: Add UART driver for Cortina-Access platform
MAINTAINERS: add me back as mxser maintainer
mxser: Documentation, fix typos
mxser: Documentation, make the docs up-to-date
mxser: Documentation, remove traces of callout device
mxser: introduce mxser_16550A_or_MUST helper
mxser: rename flags to old_speed in mxser_set_serial_info
mxser: use port variable in mxser_set_serial_info
mxser: access info->MCR under info->slock
...
|
|
Member nb in struct mvebu_uart is not set nor read. So remove it completely.
Signed-off-by: Pali Rohár <pali@kernel.org>
Link: https://lore.kernel.org/r/20210624224909.6350-7-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
For default (x16) scheme which is currently used by mvebu-uart.c driver,
maximal divisor of UART base clock is 1023*16. Therefore there is limit for
minimal supported baudrate. This change calculate it correctly and prevents
setting invalid divisor 0 into hardware registers.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-4-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Testing mvuart->clk for non-error is not enough as mvuart->clk may contain
valid clk pointer but when clk_prepare_enable(mvuart->clk) failed then
port->uartclk is zero.
When mvuart->clk is not available then port->uartclk is zero too.
Parent clock rate port->uartclk is needed to calculate UART clock divisor
and without it is not possible to change baudrate.
So fix test condition when it is possible to change baudrate.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
Link: https://lore.kernel.org/r/20210624224909.6350-3-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The clock divisor should be rounded to the closest value.
Signed-off-by: Pali Rohár <pali@kernel.org>
Fixes: 68a0db1d7da2 ("serial: mvebu-uart: add function to change baudrate")
Cc: stable@vger.kernel.org # 0e4cf69ede87 ("serial: mvebu-uart: clarify the baud rate derivation")
Link: https://lore.kernel.org/r/20210624224909.6350-2-pali@kernel.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix checkpatch warnings:
WARNING: Prefer 'unsigned int' to bare use of 'unsigned'
Signed-off-by: Jinchao Wang <wjc@cdjrlc.com>
Link: https://lore.kernel.org/r/20210624021207.58059-1-wjc@cdjrlc.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
On K3 family of SoCs (which includes AM654 SoC), it is observed that RX
TIMEOUT is signalled after RX FIFO has been drained, in which case a
dummy read of RX FIFO is required to clear RX TIMEOUT condition.
Otherwise, this would lead to an interrupt storm.
Fix this by introducing UART_RX_TIMEOUT_QUIRK flag and doing a dummy
read in IRQ handler when RX TIMEOUT is reported with no data in RX FIFO.
Fixes: be70874498f3 ("serial: 8250_omap: Add support for AM654 UART controller")
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Tested-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210622145704.11168-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Device tree bindings do not specify "hsuart" aliases, instead all serial
ports should use "serial" alias name as noted by Rob Herring [1].
Make qcom_geni_serial driver use "serial" alias and fallback to "hsuart"
if one is not found.
[1] https://lore.kernel.org/linux-arm-msm/6dd1f5cd-03c7-5945-9fa2-1c2698405110@linaro.org/
Cc: Rob Herring <robh+dt@kernel.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210621211528.1607516-1-dmitry.baryshkov@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit b61c8bf4694b5115766849378dcb8787ff54e65e. It never
made it to a public mailing list and still needs some work based on the
review comments. So revert it for now.
Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Link: https://lore.kernel.org/r/CAMuHMdXA9-ajoAza2JAW5879ECieMm1dbBbKHgJhDa7=3kWu3w@mail.gmail.com
Cc: Jason Li <jason.li@cortina-access.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This driver supports Cortina Access UART IP integrated
in most all CAXXXX line of SoCs. Earlycom is also supported
Signed-off-by: Jason Li <jason.li@cortina-access.com>
Link: https://lore.kernel.org/r/20210615165750.31261-1-alex.nemirovsky@cortina-access.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for Option International GSM-Ready 56K/ISDN PCMCIA modem
card.
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210611201940.23898-2-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The GLOBETROTTER.cis entry in serial_cs matches more devices than
intended and breaks them. Remove it.
Example: # pccardctl info
PRODID_1="Option International
"
PRODID_2="GSM-Ready 56K/ISDN
"
PRODID_3="021
"
PRODID_4="A
"
MANFID=0013,0000
FUNCID=0
result:
pcmcia 0.0: Direct firmware load for cis/GLOBETROTTER.cis failed with error -2
The GLOBETROTTER.cis is nowhere to be found. There's GLOBETROTTER.cis.ihex at
https://netdev.vger.kernel.narkive.com/h4inqdxM/patch-axnet-cs-fix-phy-id-detection-for-bogus-asix-chip#post41
It's from completely diffetent card:
vers_1 4.1, "Option International", "GSM/GPRS GlobeTrotter", "001", "A"
Signed-off-by: Ondrej Zary <linux@zary.sk>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20210611201940.23898-1-linux@zary.sk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Handle custom baud rates requested in the UPF_MAGIC_MULTIPLIER range
with BOTHER. Currently matching is exact, that is if a baud rate that
is not either of clk/4 or clk/8 is requested, then we fall through to
the default case, which will just divide the clock rate by 16 times the
rate requested, round it to closest integer, and possibly yield even
worse results then if clamping to the extra baud rates was chosen.
So for example if we have the usual base rate of 115200 and request a
rate of 230399, then the fall-through divisor calculation will yield 1,
and consequently the baud rate of 115200 will be programmed even though
obviously the magic rate of 230400 would be more appropriate.
Make the selection of the magic rates range-qualified then and use clk/4
for rates from clk/6 up (assuming `serial8250_get_baud_rate' has already
rejected any rates too far beyond clk/4), and otherwise use clk/8 for
rates from clk/12 up, and finally fall through to the standard divisor
calculation. Explicitly void using the undocumented rate of 153600bps
and stick to documented divisor values only.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105200232090.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Support for magic baud rate divisors of 32770 and 32769 used with SMSC
Super I/O chips for extra baud rates of 230400 and 460800 respectively
where base rate is 115200[1] has been added around Linux 2.5.64, which
predates our repo history, but the origin could be identified as commit
2a717aad772f ("Merge with Linux 2.5.64.") with the old MIPS/Linux repo
also at: <git://git.kernel.org/pub/scm/linux/kernel/git/ralf/linux.git>.
Code that is now in `serial8250_do_get_divisor' was added back then to
`serial8250_get_divisor', but that code would only ever trigger if one
of the higher baud rates was actually requested, and that cannot ever
happen, because the earlier call to `serial8250_get_baud_rate' never
returns them. This is because it calls `uart_get_baud_rate' with the
maximum requested being the base rate, that is clk/16 or 115200 for SMSC
chips at their nominal clock rate.
Fix it then and allow UPF_MAGIC_MULTIPLIER baud rates to be selected, by
requesting the maximum baud rate of clk/4 rather than clk/16 if the flag
has been set. Also correct the minimum baud rate, observing that these
ports only support actual (non-magic) divisors of up to 32767 only.
References:
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Table 31 - "Baud Rates", p. 77
Fixes: 1da177e4c3f4 ("Linux-2.6.12-rc2")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2105190412280.29169@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Contrary to what SMSC documentation says and unlike NS16C550A UARTs the
SMSC Super I/O IC claims compatibility with the SMSC UART implementation
does not support dividing the internal PLL clock by any divisor from 1
to 65535[1], with the exception of two magic divisors of 32769 and 32770
used respectively to select the high-speed data rates of 460800bps and
230400bps[2] if enabled on a port-by-port basis in with the Serial Port
Mode Register in the Device Configuration Space[3][4].
Instead empirical evidence indicates that the divisor, as stored in the
DLL and DLM register pair, has the range of 1 to 32767 only, and bit 7
of the DLM register (bit 15 of the divisor) effectively serves as a
selection bit for the prescaler from the base frequency of 7.3728MHz,
either 4 if the bit is 0, or 1 if the bit is 1 and high-speed operation
has been enabled with the Serial Port Mode Register.
So if high-speed operation has not been enabled, then say the values of
1 and 32769 (0x8001) written into the combined DLL and DLM register pair
both select the divisor of 1 and the baud rate of 115200bps.
[1] "FDC37M81x, PC98/99 Compliant Enhanced Super I/O Controller with
Keyboard/Mouse Wake-Up", Standard Microsystems Corporation, Rev.
03/27/2000, Section "Programmable Baud Rate Generator (and Divisor
Latches DLH, DLL)", p. 75
[2] same, Table 31 - "Baud Rates", p. 77
[3] same, Table 60 - "Serial Port 1, Logical Device 4 [Logical Device
Number = 0x04]", p. 153
[4] same, Table 61 - "Serial Port 2, Logical Device 5 [Logical Device
Number = 0x05]", p. 153
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106092330530.5469@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Oxford Semiconductor PCIe (Tornado) serial port devices are driven by a
fixed 62.5MHz clock input derived from the 100MHz PCI Express clock.
In the enhanced (650) mode, which we select in `autoconfig_has_efr' by
setting the ECB bit in the EFR register, and in the absence of clock
reconfiguration, which we currently don't do, the clock rate is divided
only by the oversampling rate of 16 as it is supplied to the baud rate
generator, yielding the baud base of 3906250. This comes from the reset
values of the TCR and MCR[7] registers which are both zero[1][2][3][4],
choosing the oversampling rate of 16 and the normal (divide by 1) baud
rate generator prescaler respectively. This is the rate that is divided
by the value held in the divisor latch to determine the baud rate used.
Replace the incorrect baud base of 4000000 with the right value of
3906250 then.
References:
[1] "OXPCIe200 PCI Express Multi-Port Bridge", Oxford Semiconductor,
Inc., DS-0045, 10 Nov 2008, Section "Reset Configuration", p. 72
[2] "OXPCIe952 PCI Express Bridge to Dual Serial & Parallel Port",
Oxford Semiconductor, Inc., DS-0046, Mar 06 08, Section "Reset
Configuration", p. 27
[3] "OXPCIe954 PCI Express Bridge to Quad Serial Port", Oxford
Semiconductor, Inc., DS-0047, Feb 08, Section "Reset Configuration",
p. 28
[4] "OXPCIe958 PCI Express Bridge to Octal Serial Port", Oxford
Semiconductor, Inc., DS-0048, Feb 08, Section "Reset Configuration",
p. 28
Fixes: 7106b4e333bae ("8250: Oxford Semiconductor Devices")
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106100203510.5469@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Oxford Semiconductor PCIe (Tornado) serial port devices have their baud
base set incorrectly, however their `pciserial_board' entries have been
reused for Titan serial port devices. Define own entries for the latter
devices then, carrying over the settings, so that Oxford entries can be
fixed.
Signed-off-by: Maciej W. Rozycki <macro@orcam.me.uk>
Link: https://lore.kernel.org/r/alpine.DEB.2.21.2106100142310.5469@angie.orcam.me.uk
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the previous patch, we introduced tty_get_char_size() and
tty_get_frame_size() for computing character and frame sizes,
respectively. Here, we make use of them in various tty drivers where
applicable.
The stats look nice: 12 insertions, 169 deletions.
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: David Lin <dtwlin@gmail.com>
Cc: Johan Hovold <johan@kernel.org>
Cc: Alex Elder <elder@kernel.org>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@foss.st.com>
Cc: Oliver Neukum <oneukum@suse.com>
Acked-by: Alex Elder <elder@kernel.org>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-4-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's a bit illogical to take magic constants in AUART_LINECTRL_WLEN.
Like in auart_console_get_options(), 2 means 7 bits. Switch
AUART_LINECTRL_WLEN to accept bit length, i.e. let it subtract 5 from
the parameter before doing the logic.
This will ease conversion from CSIZE to bits in mxs_auart_settermios()
in the next patch.
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Many tty drivers contain code to compute bits count depending on termios
cflags. So extract this code from serial core to two separate tty helper
functions:
* tty_get_char_size -- only size of a character, without flags,
* tty_get_frame_size -- complete size of a frame including flags.
In the next patch, calls to these new functions replace many copies of
this code.
Note that we accept only cflag as a parameter. That's because some
callers like pch_uart_startup or sunsab_console_setup don't have at hand
termios which we could pass around.
Cc: Joe Perches <joe@perches.com>
Cc: Johan Hovold <johan@kernel.org>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210610090247.2593-1-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Defer device probe operation when a DMA channel request probe deferral.
With this change both DMA channels are acquired before DMA channels are
configured. Once no probe deferral is expected, DMAs are
configured and any failure in their configuration will make the driver
to fallback to interrupt mode as prior this change.
Signed-off-by: Erwan Le Ray <erwan.leray@foss.st.com>
Signed-off-by: Etienne Carriere <etienne.carriere@foss.st.com>
Link: https://lore.kernel.org/r/20210610100020.2318-1-erwan.leray@foss.st.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Request the RX mailbox only after initializing the UART data
structures. Otherwise it can rarely happen that the receive
callback is called before the UART is ready.
Fixes: 2d908b38d409 ("serial: Add Tegra Combined UART driver")
Signed-off-by: Mikko Perttunen <mperttunen@nvidia.com>
Link: https://lore.kernel.org/r/20210609155655.3567545-1-mperttunen@nvidia.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Stop dmaengine transfer in sci_stop_tx(). Otherwise, the following
message is possible output when system enters suspend and while
transferring data, because clearing TIE bit in SCSCR is not able to
stop any dmaengine transfer.
sh-sci e6550000.serial: ttySC1: Unable to drain transmitter
Note that this driver has already used some #ifdef in the .c file
so that this patch also uses #ifdef to fix the issue. Otherwise,
build errors happens if the CONFIG_SERIAL_SH_SCI_DMA is disabled.
Fixes: 73a19e4c0301 ("serial: sh-sci: Add DMA support.")
Cc: <stable@vger.kernel.org> # v4.9+
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Link: https://lore.kernel.org/r/20210610110806.277932-1-yoshihiro.shimoda.uh@renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the tty fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the driver core fix in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We would like to use DMI matching in other functions as well.
Hence, extract it as exar_get_platform() helper function.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20210608144239.12697-2-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It's possible that during ->exit() the private_data is NULL,
for instance when there was no GPIO device instantiated.
Due to this we may not dereference it. Add a respective check.
Note, for now ->exit() only makes sense when GPIO device
was instantiated, that's why we may use the check for entire
function.
Fixes: 81171e7d31a6 ("serial: 8250_exar: Constify the software nodes")
Reported-by: Maxim Levitsky <mlevitsk@redhat.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Tested-by: Maxim Levitsky <mlevitsk@redhat.com>
Link: https://lore.kernel.org/r/20210608144239.12697-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The last user of the STEPFN() macro was removed in commit
d5cb1319a91d4f13 ("serial: sh-sci: Remove manual break debouncing").
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Link: https://lore.kernel.org/r/970387d104dea5bb7ea674bb89229641467e629b.1623076891.git.geert+renesas@glider.be
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add serial support for RZ/G2L SoC with earlycon and
extended mode register support.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
Signed-off-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Link: https://lore.kernel.org/r/20210603221758.10305-11-prabhakar.mahadev-lad.rj@bp.renesas.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Remove the hack to assign the global console_port variable at probe time.
This assumption that cons->index is -1 is wrong for systems that specify
'console=' in the cmdline (or 'stdout-path' in dts). Hence, on such system
the actual console assignment is ignored, and the first UART that happens
to be probed is used as console instead.
Move the logic to console_setup() and map the console to the correct port
through the array of available ports instead.
Signed-off-by: Daniel Mack <daniel@zonque.org>
Link: https://lore.kernel.org/r/20210528133321.1859346-1-daniel@zonque.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In order to optimize serial communication (performance/throughput VS
latency), we may need to tweak DMA period number and size. This adds
DT properties to configure those values before initialising DMA.
The defaults will stay the same as before.
[update documentation and commit message, rebase to current master,
switch back to DT instead of sysfs]
Signed-off-by: Fabien Lahoudere <fabien.lahoudere@collabora.com>
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.com>
Link: https://lore.kernel.org/r/20210430175038.103226-2-sebastian.reichel@collabora.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the tty/serial fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We need the driver core fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty
Pull tty / serial driver fixes from Greg KH:
"Here are some small fixes for reported problems for tty and serial
drivers for 5.13-rc4.
They consist of:
- 8250 bugfixes and new device support
- lockdown security mode fixup
- syzbot found problems fixed
- 8250_omap fix for interrupt storm
- revert of 8250_omap driver fix as it caused worse problem than the
original issue
All but the last patch have been in linux-next for a while, the last
one is a revert of a problem found in linux-next with the 8250_omap
driver change"
* tag 'tty-5.13-rc4' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/tty:
Revert "serial: 8250: 8250_omap: Fix possible interrupt storm"
serial: 8250_pci: handle FL_NOIRQ board flag
serial: rp2: use 'request_firmware' instead of 'request_firmware_nowait'
serial: 8250_pci: Add support for new HPE serial device
serial: 8250: 8250_omap: Fix possible interrupt storm
serial: 8250: Use BIT(x) for UART_{CAP,BUG}_*
serial: 8250: Add UART_BUG_TXRACE workaround for Aspeed VUART
serial: 8250_dw: Add device HID for new AMD UART controller
serial: sh-sci: Fix off-by-one error in FIFO threshold register setting
serial: core: fix suspicious security_locked_down() call
serial: tegra: Fix a mask operation that is always true
|
|
This reverts commit 31fae7c8b18c3f8029a2a5dce97a3182c1a167a0.
Tony writes:
I just noticed this causes the following regression in Linux
next when pressing a key on uart console after boot at least on
omap3. This seems to happen on serial_port_in(port, UART_RX) in
the quirk handling.
So let's drop this.
Cc: stable@vger.kernel.org
Link: https://lore.kernel.org/r/YLCCJzkkB4N7LTQS@atomide.com
Fixes: 31fae7c8b18c ("serial: 8250: 8250_omap: Fix possible interrupt storm")
Reported-by: Tony Lindgren <tony@atomide.com>
Cc: Jan Kiszka <jan.kiszka@siemens.com>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In commit 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support")
the way the irq gets allocated was changed. With that change the
handling FL_NOIRQ got lost. Restore the old behaviour.
Fixes: 8428413b1d14 ("serial: 8250_pci: Implement MSI(-X) support")
Cc: <stable@vger.kernel.org>
Signed-off-by: Christian Gmeiner <christian.gmeiner@gmail.com>
Link: https://lore.kernel.org/r/20210527095529.26281-1-christian.gmeiner@gmail.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In the probe function, if the final 'serial_config()' fails, 'info' is
leaking.
Add a resource handling path to free this memory.
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/dc25f96b7faebf42e60fe8d02963c941cf4d8124.1621971720.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
In 'rp2_probe', the driver registers 'rp2_uart_interrupt' then calls
'rp2_fw_cb' through 'request_firmware_nowait'. In 'rp2_fw_cb', if the
firmware don't exists, function just return without initializing ports
of 'rp2_card'. But now the interrupt handler function has been
registered, and when an interrupt comes, 'rp2_uart_interrupt' may access
those ports then causing NULL pointer dereference or other bugs.
Because the driver does some initialization work in 'rp2_fw_cb', in
order to make the driver ready to handle interrupts, 'request_firmware'
should be used instead of asynchronous 'request_firmware_nowait'.
This report reveals it:
INFO: trying to register non-static key.
the code is fine but needs lockdep annotation.
turning off the locking correctness validator.
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.19.177-gdba4159c14ef-dirty #45
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-
gc9ba5276e321-prebuilt.qemu.org 04/01/2014
Call Trace:
<IRQ>
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xec/0x156 lib/dump_stack.c:118
assign_lock_key kernel/locking/lockdep.c:727 [inline]
register_lock_class+0x14e5/0x1ba0 kernel/locking/lockdep.c:753
__lock_acquire+0x187/0x3750 kernel/locking/lockdep.c:3303
lock_acquire+0x124/0x340 kernel/locking/lockdep.c:3907
__raw_spin_lock include/linux/spinlock_api_smp.h:142 [inline]
_raw_spin_lock+0x32/0x50 kernel/locking/spinlock.c:144
spin_lock include/linux/spinlock.h:329 [inline]
rp2_ch_interrupt drivers/tty/serial/rp2.c:466 [inline]
rp2_asic_interrupt.isra.9+0x15d/0x990 drivers/tty/serial/rp2.c:493
rp2_uart_interrupt+0x49/0xe0 drivers/tty/serial/rp2.c:504
__handle_irq_event_percpu+0xfb/0x770 kernel/irq/handle.c:149
handle_irq_event_percpu+0x79/0x150 kernel/irq/handle.c:189
handle_irq_event+0xac/0x140 kernel/irq/handle.c:206
handle_fasteoi_irq+0x232/0x5c0 kernel/irq/chip.c:725
generic_handle_irq_desc include/linux/irqdesc.h:155 [inline]
handle_irq+0x230/0x3a0 arch/x86/kernel/irq_64.c:87
do_IRQ+0xa7/0x1e0 arch/x86/kernel/irq.c:247
common_interrupt+0xf/0xf arch/x86/entry/entry_64.S:670
</IRQ>
RIP: 0010:native_safe_halt+0x28/0x30 arch/x86/include/asm/irqflags.h:61
Code: 00 00 55 be 04 00 00 00 48 c7 c7 00 c2 2f 8c 48 89 e5 e8 fb 31 e7 f8
8b 05 75 af 8d 03 85 c0 7e 07 0f 00 2d 8a 61 65 00 fb f4 <5d> c3 90 90 90
90 90 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41
RSP: 0018:ffff88806b71fcc8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffde
RAX: 0000000000000000 RBX: ffffffff8bde7e48 RCX: ffffffff88a21285
RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff8c2fc200
RBP: ffff88806b71fcc8 R08: fffffbfff185f840 R09: fffffbfff185f840
R10: 0000000000000001 R11: fffffbfff185f840 R12: 0000000000000002
R13: ffffffff8bea18a0 R14: 0000000000000000 R15: 0000000000000000
arch_safe_halt arch/x86/include/asm/paravirt.h:94 [inline]
default_idle+0x6f/0x360 arch/x86/kernel/process.c:557
arch_cpu_idle+0xf/0x20 arch/x86/kernel/process.c:548
default_idle_call+0x3b/0x60 kernel/sched/idle.c:93
cpuidle_idle_call kernel/sched/idle.c:153 [inline]
do_idle+0x2ab/0x3c0 kernel/sched/idle.c:263
cpu_startup_entry+0xcb/0xe0 kernel/sched/idle.c:369
start_secondary+0x3b8/0x4e0 arch/x86/kernel/smpboot.c:271
secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:243
BUG: unable to handle kernel NULL pointer dereference at 0000000000000010
PGD 8000000056d27067 P4D 8000000056d27067 PUD 56d28067 PMD 0
Oops: 0000 [#1] PREEMPT SMP KASAN PTI
CPU: 2 PID: 0 Comm: swapper/2 Not tainted 4.19.177-gdba4159c14ef-dirty #45
Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS rel-1.12.0-59-
gc9ba5276e321-prebuilt.qemu.org 04/01/2014
RIP: 0010:readl arch/x86/include/asm/io.h:59 [inline]
RIP: 0010:rp2_ch_interrupt drivers/tty/serial/rp2.c:472 [inline]
RIP: 0010:rp2_asic_interrupt.isra.9+0x181/0x990 drivers/tty/serial/rp2.c:
493
Code: df e8 43 5d c2 05 48 8d 83 e8 01 00 00 48 89 85 60 ff ff ff 48 c1 e8
03 42 80 3c 30 00 0f 85 aa 07 00 00 48 8b 83 e8 01 00 00 <8b> 40 10 89 c1
89 85 68 ff ff ff 48 8b 83 e8 01 00 00 89 48 10 83
RSP: 0018:ffff88806c287cd0 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff88806ade6820 RCX: ffffffff814300b1
RDX: 1ffff1100d5bcd06 RSI: 0000000000000004 RDI: ffff88806ade6820
RBP: ffff88806c287db8 R08: ffffed100d5bcd05 R09: ffffed100d5bcd05
R10: 0000000000000001 R11: ffffed100d5bcd04 R12: ffffc90001e00000
R13: ffff888069654e10 R14: dffffc0000000000 R15: ffff888069654df0
FS: 0000000000000000(0000) GS:ffff88806c280000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000010 CR3: 000000006892c000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Call Trace:
<IRQ>
rp2_uart_interrupt+0x49/0xe0 drivers/tty/serial/rp2.c:504
__handle_irq_event_percpu+0xfb/0x770 kernel/irq/handle.c:149
handle_irq_event_percpu+0x79/0x150 kernel/irq/handle.c:189
handle_irq_event+0xac/0x140 kernel/irq/handle.c:206
handle_fasteoi_irq+0x232/0x5c0 kernel/irq/chip.c:725
generic_handle_irq_desc include/linux/irqdesc.h:155 [inline]
handle_irq+0x230/0x3a0 arch/x86/kernel/irq_64.c:87
do_IRQ+0xa7/0x1e0 arch/x86/kernel/irq.c:247
common_interrupt+0xf/0xf arch/x86/entry/entry_64.S:670
</IRQ>
RIP: 0010:native_safe_halt+0x28/0x30 arch/x86/include/asm/irqflags.h:61
Code: 00 00 55 be 04 00 00 00 48 c7 c7 00 c2 2f 8c 48 89 e5 e8 fb 31 e7
f8 8b 05 75 af 8d 03 85 c0 7e 07 0f 00 2d 8a 61 65 00 fb f4 <5d> c3 90
90 90 90 90 90 0f 1f 44 00 00 55 48 89 e5 41 57 41 56 41
RSP: 0018:ffff88806b71fcc8 EFLAGS: 00000246 ORIG_RAX: ffffffffffffffde
RAX: 0000000000000000 RBX: ffffffff8bde7e48 RCX: ffffffff88a21285
RDX: 0000000000000000 RSI: 0000000000000004 RDI: ffffffff8c2fc200
RBP: ffff88806b71fcc8 R08: fffffbfff185f840 R09: fffffbfff185f840
R10: 0000000000000001 R11: fffffbfff185f840 R12: 0000000000000002
R13: ffffffff8bea18a0 R14: 0000000000000000 R15: 0000000000000000
arch_safe_halt arch/x86/include/asm/paravirt.h:94 [inline]
default_idle+0x6f/0x360 arch/x86/kernel/process.c:557
arch_cpu_idle+0xf/0x20 arch/x86/kernel/process.c:548
default_idle_call+0x3b/0x60 kernel/sched/idle.c:93
cpuidle_idle_call kernel/sched/idle.c:153 [inline]
do_idle+0x2ab/0x3c0 kernel/sched/idle.c:263
cpu_startup_entry+0xcb/0xe0 kernel/sched/idle.c:369
start_secondary+0x3b8/0x4e0 arch/x86/kernel/smpboot.c:271
secondary_startup_64+0xa4/0xb0 arch/x86/kernel/head_64.S:243
Modules linked in:
Dumping ftrace buffer:
(ftrace buffer empty)
CR2: 0000000000000010
---[ end trace 11804dbb55cb1a64 ]---
RIP: 0010:readl arch/x86/include/asm/io.h:59 [inline]
RIP: 0010:rp2_ch_interrupt drivers/tty/serial/rp2.c:472 [inline]
RIP: 0010:rp2_asic_interrupt.isra.9+0x181/0x990 drivers/tty/serial/rp2.c:
493
Code: df e8 43 5d c2 05 48 8d 83 e8 01 00 00 48 89 85 60 ff ff ff 48 c1
e8 03 42 80 3c 30 00 0f 85 aa 07 00 00 48 8b 83 e8 01 00 00 <8b> 40 10 89
c1 89 85 68 ff ff ff 48 8b 83 e8 01 00 00 89 48 10 83
RSP: 0018:ffff88806c287cd0 EFLAGS: 00010046
RAX: 0000000000000000 RBX: ffff88806ade6820 RCX: ffffffff814300b1
RDX: 1ffff1100d5bcd06 RSI: 0000000000000004 RDI: ffff88806ade6820
RBP: ffff88806c287db8 R08: ffffed100d5bcd05 R09: ffffed100d5bcd05
R10: 0000000000000001 R11: ffffed100d5bcd04 R12: ffffc90001e00000
R13: ffff888069654e10 R14: dffffc0000000000 R15: ffff888069654df0
FS: 0000000000000000(0000) GS:ffff88806c280000(0000) knlGS:
0000000000000000
CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
CR2: 0000000000000010 CR3: 000000006892c000 CR4: 00000000000006e0
DR0: 0000000000000000 DR1: 0000000000000000 DR2: 0000000000000000
DR3: 0000000000000000 DR6: 00000000fffe0ff0 DR7: 0000000000000400
Reported-by: Zheyu Ma <zheyuma97@gmail.com>
Signed-off-by: Zheyu Ma <zheyuma97@gmail.com>
Link: https://lore.kernel.org/r/1621577323-1541-1-git-send-email-zheyuma97@gmail.com
Cc: stable <stable@vger.kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This reverts commit 064b6e47b2b2d4a20566ba6f8dc90e46b599b35f as it
wasn't quite ready yet :(
Cc: Biju Das <biju.das.jz@bp.renesas.com>
CC: Geert Uytterhoeven <geert+renesas@glider.be>
Reported-by: Lad Prabhakar <prabhakar.mahadev-lad.rj@bp.renesas.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add support for new HPE serial device. It is MSI enabled,
but otherwise similar to legacy HP server serial devices.
Tested-by: Jerry Hoemann <jerry.hoemann@hpe.com>
Signed-off-by: Randy Wright <rwright@hpe.com>
Cc: stable <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/1621009614-28836-1-git-send-email-rwright@hpe.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is possible that RX TIMEOUT is signalled after RX FIFO has been
drained, in which case a dummy read of RX FIFO is required to clear RX
TIMEOUT condition. Otherwise, RX TIMEOUT condition is not cleared
leading to an interrupt storm
Cc: stable@vger.kernel.org
Reported-by: Jan Kiszka <jan.kiszka@siemens.com>
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Link: https://lore.kernel.org/r/20210511151955.28071-1-vigneshr@ti.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
BIT(x) improves readability and safety with respect to shifts.
Reviewed-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Link: https://lore.kernel.org/r/20210520021334.497341-3-andrew@aj.id.au
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
