| Age | Commit message (Collapse) | Author |
|---|
|
In this step, the read/write routines for the descriptors are converted
to use __le32 quantities, thus a lot of casts can be removed. Callback
routines still use the 8-bit arrays, but these are changed within the
specified routine.
The macro that cleared a descriptor has now been converted into an inline
routine.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
As a first step in the conversion, the macros that set the RX and TX
descriptors are converted to static inline routines, and the names are
changed from upper to lower case. To minimize the changes in a given
step, the input descriptor information is left as as a byte array
(u8 *), even though it should be a little-endian word array (__le32 *).
That will be changed in the next patch.
Several places where checkpatch.pl complains about a space after a cast
are fixed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
This driver uses a set of local macros to manipulate the RX and TX
descriptors, which are all little-endian quantities. These macros
are replaced by the bitfield macros le32p_replace_bits() and
le32_get_bits(). In several places, the macros operated on an entire
32-bit word. In these cases, a direct read or replacement is used.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
iAs the first step in converting from macros that get/set information
in the RX and TX descriptors, unused macros are being removed.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
The traditional license information is replaced by the SPDX form. There
are no code changes.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Because the hal_op rx_command_packet does C2H handler if rx packet type
is C2H, and the handler have been moved to base.c so we can call the
handler directly.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
1. Both 32-bit and 64-bit use the same TX/RX buffer desc layout
2. Extend set_desc() and get_desc() to set and get 64-bit address
3. Remove directive DMA_IS_64BIT
4. Add module parameter to turn on 64-bit dma
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
When using EAPOL to do a PTK rekey, there is a possible race condition.
When msg 3/4 is received, the supplicant will send msg 4/4 and install
the new key immediately; however, the driver must make sure that msg 4/4
is sent before installing the new key. We use TX report to ensure it is
sent.
Signed-off-by: Ping-Ke Shih <pkshih@realtek.com>
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Cc: Yan-Hsuan Chuang <yhchuang@realtek.com>
Cc: Birming Chiu <birming@realtek.com>
Cc: Shaofu <shaofu@realtek.com>
Cc: Steven Ting <steventing@realtek.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Compiling the rtlwifi drivers for ARM with gcc -Wextra warns about lots of
incorrect code that results from 'char' being unsigned here, e.g.
realtek/rtlwifi/rc.c:113:18: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8188ee/dm.c:1070:22: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192ce/trx.c:54:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192cu/mac.c:601:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192de/trx.c:53:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192ee/phy.c:1268:12: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8192se/rf.c:150:20: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8723be/dm.c:877:29: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8723be/phy.c:386:16: error: comparison is always true due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/dm.c:1514:38: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/phy.c:1558:11: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/phy.c:386:24: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/rtl8821ae/trx.c:55:12: error: comparison is always false due to limited range of data type [-Werror=type-limits]
realtek/rtlwifi/stats.c:31:16: error: comparison is always false due to limited range of data type [-Werror=type-limits]
This patch changes all uses of 'char' in this driver that refer to
8-bit integers to use 's8' instead, which is signed on all architectures.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
passing rtl_stats by value is inefficient; the structure is over 300
bytes in size and generally just one field (packet_report_type)
is being accessed, so the pass by value is a relatively large overhead.
This change just affects just the rx_command_packet calls.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
Now that a new mac80211-based driver for Realtek devices has been submitted,
it is time to reorganize the directories. Rather than having directories
rtlwifi and rtl818x be in drivers/net/wireless/, they will now be in
drivers/net/wireless/realtek/. This change simplifies the directory
structure, but does not result in any configuration changes that are
visable to the user.
Signed-off-by: Larry Finger <Larry.Finger@lwfinger.net>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
