| Age | Commit message (Collapse) | Author |
|---|
|
Commit 46060be6d840 ("clk: sunxi-ng: v3s: use sigma-delta modulation for audio-pll")
changed the audio pll on the Allwinner V3s and V3 SoCs to use
sigma-delta modulation. In the process the declaration of fixed postdivider
providing "pll-audio" was adjusted to provide the desired clock rates from
the now sigma-delta modulated pll.
However, while the divider used for calculations by the clock framework
was adjusted the actual divider programmed into the hardware in
sun8i_v3_v3s_ccu_init was left at "divide by four". This broke the
"pll-audio" clock, now only providing quater the expected clock rate.
It would in general be desirable to program the postdivider for
"pll-audio" to four, such that a broader range of frequencies were
available on the pll outputs. But the clock for the integrated codec
"ac-dig" does not feature a mux that allows to select from all pll outputs
as it is just a simple clock gate connected to "pll-audio". Thus we need
to set the postdivider to one to be able to provide the 22.5792MHz and
24.576MHz rates required by the internal sun4i codec.
This patches fixes the incorrect clock rate by forcing the postdivider to
one in sun8i_v3_v3s_ccu_init.
Fixes: 46060be6d840 ("clk: sunxi-ng: v3s: use sigma-delta modulation for audio-pll")
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210513131315.2059451-1-t.schramm@manjaro.org
|
|
Previously it was not possible to achieve clock rates of 24.576MHz and
22.5792MHz, which are commonly required core clocks for the i2s
peripheral of v3s based SoCs.
Add support for those clock rates through the audio pll's sigma-delta
modulator.
Signed-off-by: Tobias Schramm <t.schramm@manjaro.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210218112001.479018-2-t.schramm@manjaro.org
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This is all driver updates, the majority of which is a bunch of new
Qualcomm clk drivers that dominate the diffstat because we add support
for six SoCs from that particular vendor.
The other big change is the removal of various clk drivers that are no
longer used now that the kernel is dropping support for those SoCs.
Beyond that there's the usual non-critical fixes for existing drivers
and a good number of patches from Lee Jones that cleanup a bunch of
W=1 enabled builds.
Removed Drivers:
- Remove efm32 clk driver
- Remove tango4 clk driver
- Remove zte zx clk driver
- Remove sirf prima2/atlast clk drivers
- Remove u300 clk driver
New Drivers:
- PLL support on MStar/SigmaStar ARMv7 SoCs
- CPU clks for Qualcomm SDX55
- GCC and RPMh clks for Qualcomm SC8180x and SC7280 SoCs
- GCC clks for Qualcomm SM8350
- GPU clks for Qualcomm SDM660/SDM630
Updates:
- Video clk fixups on Qualcomm SM8250
- Improvements for multimedia clks on Qualcomm MSM8998
- Fix many warnings with W=1 enabled builds under drivers/clk/
- Support crystal load capacitance for Versaclock VC5
- Add a "skip recall" DT binding for Silicon Labs' si570 to avoid
glitches at boot
- Convert Xilinx VCU clk driver to a proper clk provider driver
- Expose Xilinx ZynqMP clk driver to more platforms
- Amlogic pll driver fixup
- Amlogic meson8b clock controller dt support clean up
- Remove mipi clk from the Amlogic axg clock controller
- New Rockchip rk3368 clock ids related to camera input
- Use pr_notice() instead of pr_warn() on i.MX6Q pre-boot ldb_di_clk
reparenting
- A series from Liu Ying that adds some SCU clocks support for
i.MX8qxp DC0/MIPI-LVDS subsystems
- A series from Lucas Stach that adds PLL monitor clocks for i.MX8MQ,
and clkout1/2 support for i.MX8MM/MN
- Add I2c and Ethernet (RAVB) clocks on Renesas R-Car V3U
- Add timer (TMU) clocks on most Renesas R-Car Gen3 SoCs
- Add video-related (FCPVD/VSPD/VSPX), watchdog (RWDT), serial
(HSCIF), pincontrol/GPIO (PFC/GPIO), SPI (MSIOF), SDHI, and DMA
(SYS-DMAC) clocks on Renesas R-Car V3U
- Add support for the USB 2.0 clock selector on Renesas RZ/G2 SoCs
- Allwinner H616 SoC clk support"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (171 commits)
clk: mstar: msc313-mpll: Fix format specifier
clk: mstar: Allow MStar clk drivers to be compile tested
clk: qoriq: use macros to generate pll_mask
clk: qcom: Add Global Clock controller (GCC) driver for SC7280
dt-bindings: clock: Add SC7280 GCC clock binding
clk: qcom: rpmh: Add support for RPMH clocks on SC7280
dt-bindings: clock: Add RPMHCC bindings for SC7280
clk: qcom: gcc-sm8350: add gdsc
dt-bindings: clock: Add QCOM SDM630 and SDM660 graphics clock bindings
clk: qcom: Add SDM660 GPU Clock Controller (GPUCC) driver
clk: qcom: mmcc-msm8996: Migrate gfx3d clock to clk_rcg2_gfx3d
clk: qcom: rcg2: Stop hardcoding gfx3d pingpong parent numbers
dt-bindings: clock: Add support for the SDM630 and SDM660 mmcc
clk: qcom: Add SDM660 Multimedia Clock Controller (MMCC) driver
clk: qcom: gcc-sdm660: Mark GPU CFG AHB clock as critical
clk: qcom: gcc-sdm660: Mark MMSS NoC CFG AHB clock as critical
clk: qcom: gpucc-msm8998: Allow fabia gpupll0 rate setting
clk: qcom: gpucc-msm8998: Add resets, cxc, fix flags on gpu_gx_gdsc
clk: qcom: gdsc: Implement NO_RET_PERIPH flag
clk: mstar: MStar/SigmaStar MPLL driver
...
|
|
CLK_SET_RATE_PARENT flag is checked on parent clock instead of current
one. Fix that.
Fixes: 3f790433c3cb ("clk: sunxi-ng: Adjust MP clock parent rate when allowed")
Reviewed-by: Chen-Yu Tsai <wens@csie.org>
Tested-by: Andre Heider <a.heider@gmail.com>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20210209175900.7092-2-jernej.skrabec@siol.net
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
While the clocks are fairly similar to the H6, many differ in tiny
details, so a separate clock driver seems indicated.
Derived from the H6 clock driver, and adjusted according to the manual.
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210127172500.13356-4-andre.przywara@arm.com
|
|
The clocks itself are identical to the H6 R-CCU, it's just that the H616
has not all of them implemented (or connected).
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210127172500.13356-3-andre.przywara@arm.com
|
|
While comparing clocks between the H6 and H616, some of the M factor
ranges were found to be wrong: the manual says they are only covering
two bits [1:0], but our code had "5" in the number-of-bits field.
By writing 0xff into that register in U-Boot and via FEL, it could be
confirmed that bits [4:2] are indeed masked off, so the manual is right.
Change to number of bits in the affected clock's description.
Fixes: 524353ea480b ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210118000912.28116-1-andre.przywara@arm.com
|
|
The CEC clock on the H6 SoC is a bit special, since it uses a fixed
pre-dividier for one source clock (the PLL), but conveys the other clock
(32K OSC) directly.
We are using a fixed predivider array for that, but fail to use the right
flag to actually activate that.
Fixes: 524353ea480b ("clk: sunxi-ng: add support for the Allwinner H6 CCU")
Reported-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Andre Przywara <andre.przywara@arm.com>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20210106143246.11255-1-andre.przywara@arm.com
|
|
While no information about the H6 RSB controller is included in the
datasheet or manual, the vendor BSP and power management blob both
reference the RSB clock parent and register address. These values were
verified by experimentation.
Since this clock/reset are added late, the specifier is added at the end
to maintain the existing DT binding. The code is kept in register order.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
Two clock divider tables are missing sentinel at the end. Effect of that
is that clock framework reads past the last entry. Fix that with adding
sentinel at the end.
Issue was discovered with KASan.
Fixes: 0577e4853bfb ("clk: sunxi-ng: Add H3 clocks")
Fixes: c6a0637460c2 ("clk: sunxi-ng: Add A64 clocks")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Link: https://lore.kernel.org/r/20201202203817.438713-1-jernej.skrabec@siol.net
Acked-by: Maxime Ripard <mripard@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Audio cores need specific clock rates which can't be simply obtained by
adjusting integer multipliers and dividers. HW for such cases supports
delta-sigma modulation which enables fractional multipliers.
Port H3 delta-sigma table to R40. They have identical audio PLLs.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://lore.kernel.org/r/20200825131049.1277596-1-jernej.skrabec@siol.net
|
|
Add support for a100 in the sunxi-ng CCU framework.
Signed-off-by: Yangtao Li <frank@allwinnertech.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/1eb41bf6c966a0e54820200650d27a5d4f2ac160.1595572867.git.frank@allwinnertech.com
|
|
V3s quirks are not in right place. Move it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
R40 is actually very similar to A64, but it doesn't have mixer1 reset.
This means it's clocks and resets combination is unique and R40 specific
quirks are needed.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
A83T structures don't have clocks and reset for rotation core. Add them.
Fixes: 763c5bd045b1 ("clk: sunxi-ng: add support for DE2 CCU")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Currently, V3s and H3 reuse A83T reset structure. However, A83T contains
additional core for rotation, which is not present in V3s and H3.
Make new reset structure for H3 and let V3s reuse it. A83T reset
structure will be amended in subsequent commit.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
DE3 documentation regarding presence of rotate core in H6 is a bit
confusing. Register descriptions mention bits for enabling rotate core
clocks and reset, but general overview doesn't list it as feature of H6
display engine, BSP kernel doesn't support it and there is no interrupt
listed for it. Manual poking registers also didn't reveal presence of
rotate core.
Let's assume there isn't any rotate core on H6 present and remove
related clocks. With that done, structures are same as those for H5, so
just reuse H5 structure.
Fixes: 56808da9f97f ("clk: sunxi-ng: Add support for H6 DE3 clocks")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
A64 has rotation core which needs clocks and reset. Because there is no
appropriate structures available, make a separate, A64 specific
structures.
Fixes: cf4881c12935 ("clk: sunxi-ng: fix the A64/H5 clock description of DE2 CCU")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
H5 has less clocks and resets than A64. Currently that's not obvious
because A64 is missing rotation core related clocks and reset.
Split out H5 definition. A64 structures will be fixed in subsequent
commit.
Note that this patch depends on commit 19368d99746e ("clk: sunxi-ng:
add support for Allwinner H3 DE2 CCU") for the H3 clock list.
Fixes: 763c5bd045b1 ("clk: sunxi-ng: add support for DE2 CCU")
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
MBUS clock will be referenced in MBUS controller node.
Export it.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There are a few changes to the core framework this time around, in
addition to the normal collection of driver updates to support new
SoCs, fix incorrect data, and convert various drivers to clk_hw based
APIs.
In the core, we allow clk_ops::init() to return an error code now so
that we can fail clk registration if the callback does something like
fail to allocate memory. We also add a new "terminate" clk_op so that
things done in clk_ops::init() can be undone, e.g. free memory. We
also spit out a warning now when critical clks fail to enable and we
support changing clk rates and enable/disable state through debugfs
when developers compile the kernel themselves.
On the driver front, we get support for what seems like a lot of
Qualcomm and NXP SoCs given that those vendors dominate the diffstat.
There are a couple new drivers for Xilinx and Amlogic SoCs too. The
updates are all small things like fixing the way glitch free muxes
switch parents, avoiding div-by-zero problems, or fixing data like
parent names. See the updates section below for more details.
Finally, the "basic" clk types have been converted to support
specifying parents with clk_hw pointers. This work includes an
overhaul of the fixed-rate clk type to be more modern by using clk_hw
APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw
based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config
symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M
SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (140 commits)
dt/bindings: clk: fsl,plldig: Drop 'bindings' from schema id
clk: ls1028a: Fix warning on clamp() usage
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
...
|
|
The MIPI PLL is used for LVDS. Make sure it's exported in the dt bindings
headers.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The MIPI PLL is used for LVDS. Make sure it's exported in the dt bindings
headers.
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Export CLK_CPUX so we can reference it in CPU node.
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The A64 PLL_CPU clock has the same instability if some factor changed
without the PLL gated like other SoCs with sun6i-style CCU, e.g. A33,
H3.
Add the mux and pll notifiers for A64 CPU clock to workaround the
problem.
Fixes: c6a0637460c2 ("clk: sunxi-ng: Add A64 clocks")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Vasily Khoruzhick <anarsoul@gmail.com>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The MBUS clock needs to be referenced in the MBUS device node.
Export it.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
According to the BSP source code, both the AR100 and R_APB2 clocks have
PLL_PERIPH0 as mux index 3, not 2 as it was on previous chips. The pre-
divider used for PLL_PERIPH0 should be changed to index 3 to match.
This was verified by running a rough benchmark on the AR100 with various
clock settings:
| mux | pre-divider | iterations/second | clock source |
|=====|=============|===================|==============|
| 0 | 0 | 19033 (stable) | osc24M |
| 2 | 5 | 11466 (unstable) | iosc/osc16M |
| 2 | 17 | 11422 (unstable) | iosc/osc16M |
| 3 | 5 | 85338 (stable) | pll-periph0 |
| 3 | 17 | 27167 (stable) | pll-periph0 |
The relative performance numbers all match up (with pll-periph0 running
at its default 600MHz).
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
Like the APB0 clock on previous chips, this is a simple single-parent
clock with an M divider. Use the equivalent helper macro instead of
writing out the whole clock description manually.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
According to the BSP source code, the APB0 clock on the H3 and H5 has a
normal M divider, not a power-of-two divider. This matches the hardware
in the A83T (as described in both the BSP source code and the manual).
Since the A83T and H3/A64 clocks are actually the same, we can merge the
definitions.
Signed-off-by: Samuel Holland <samuel@sholland.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
One of the uses of the external clock outputs is to provide a stable
32768 Hz clock signal to WiFi and Bluetooth chips. On the R40, the RTC
has an internal RC oscillator that is muxed with the external crystal.
Allow setting the parent rate for the external clock outputs so that
requests for 32768 Hz get passed to the RTC's clock driver to mux in
the external crystal if it isn't already muxed correctly.
Fixes: cd030a78f7aa ("clk: sunxi-ng: support R40 SoC")
Fixes: 01a7ea763fc4 ("clk: sunxi-ng: r40: Force LOSC parent to RTC LOSC output")
Cc: <stable@kernel.org>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The hws field of sun8i_v3s_hw_clks has only 74
members. However, the number specified by CLK_NUMBER
is 77 (= CLK_I2S0 + 1). This leads to runtime segmentation
fault that is not always reproducible.
This patch fixes the problem by specifying correct clock number.
Signed-off-by: Yunhao Tian <18373444@buaa.edu.cn>
[Maxime: Also remove the CLK_NUMBER definition]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This merge window we have one small clk provider API in the core
framework and then a bunch of driver updates and a handful of new
drivers. In terms of diffstat the Qualcomm and Amlogic drivers are
high up there because of all the clk data introcued by new drivers.
The Nvidia Tegra driver had a lot of work done this cycle too to
support suspend/resume and memory controllers. And the OMAP clk driver
got proper clk and reset handling in place.
Rounding out the patches are various updates to remove unused data,
mark things static, correct incorrect data in drivers, etc. All the
little things that improve drivers and maintain code health. I will
point out that there's a patch in here for the GPIO clk driver, that
almost nobody uses, which changes behavior and causes clk_set_rate()
to try to change the GPIO gate clk's parent. Other than that things
are fairly well SoC specific here.
Core:
- Add a clk provider API to get current parent index
- Plug a memory leak in clk_unregister() path
New Drivers:
- CGU in Ingenix X1000
- Bitmain BM1880 clks
- Qualcomm MSM8998 GPU clk controllers
- Qualcomm SC7180 GCC and RPMH clk controllers
- Qualcomm QCS404 Q6SSTOP clk controllers
- Add support for the Renesas R-Car M3-W+ (r8a77961) SoC
- Add support for the Renesas RZ/G2N (r8a774b1) SoC
- Add Tegra20/30 External Memory Clock (EMC) support
Updates:
- Make gpio gate clks propagate rate setting up to parent
- Prepare Armada 3700 for suspend to RAM by moving PCIe
suspend/resume priority
- Drop unused variables, enums, etc. in various clk drivers
- Convert various drivers to use devm_platform_ioremap_resource()
- Use struct_size() some more in various clk drivers
- Improve Rockchip px30 clk tree
- Add suspend/resume support to Tegra210 clk driver
- Reimplement SOR clks on earlier Tegra SoCs, helping HDMI and DP
- Allwinner DT exports and H6 clk tree fixes
- Proper clk and reset handling for OMAP SoCs
- Revamped TI divider clk to clamp max divider
- Make 1443X/1416X PLL clock structure common for reusing among i.MX8
SoCs
- Drop IMX7ULP_CLK_MIPI_PLL clock, it shouldn't be used
- Add VIDEO2_PLL clock for imx8mq
- Add missing gate clock for pll1/2 fixed dividers on i.MX8 SoCs
- Add sm1 support in the Amlogic audio clock controller
- Switch some clocks on R-Car Gen2/3 to .determine_rate()
- Remove Renesas R-Car Gen2 legacy DT clock support
- Improve arithmetic divisions on Renesas R-Car Gen2 and Gen3
- Improve Renesas R-Car Gen3 SD clock handling
- Add rate table for Samsung exynos542x GPU and VPLL clks
- Fix potential CPU performance degradation after system
suspend/resume cycle on exynos542x SoCs"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (160 commits)
clk: aspeed: Add RMII RCLK gates for both AST2500 MACs
MAINTAINERS: Add entry for BM1880 SoC clock driver
clk: Add common clock driver for BM1880 SoC
dt-bindings: clock: Add devicetree binding for BM1880 SoC
clk: Add clk_hw_unregister_composite helper function definition
clk: Zero init clk_init_data in helpers
clk: ingenic: Allow drivers to be built with COMPILE_TEST
MAINTAINERS: Update section for Ux500 clock drivers
clk: mark clk_disable_unused() as __init
clk: Fix memory leak in clk_unregister()
clk: Ingenic: Add CGU driver for X1000.
dt-bindings: clock: Add X1000 bindings.
clk: tegra: Use match_string() helper to simplify the code
clk: pxa: fix one of the pxa RTC clocks
clk: sprd: Use IS_ERR() to validate the return value of syscon_regmap_lookup_by_phandle()
clk: armada-xp: remove unused code
clk: tegra: Fix build error without CONFIG_PM_SLEEP
clk: tegra: Add missing stubs for the case of !CONFIG_PM_SLEEP
clk: tegra: Optimize PLLX restore on Tegra20/30
clk: tegra: Add suspend and resume support on Tegra210
...
|
|
MBUS clock will be referenced in MBUS controller node.
Export it.
Acked-by: Maxime Ripard <mripard@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
|
|
The zero'ing of bits 16 and 18 is incorrect. Currently the code
is masking with the bitwise-and of BIT(16) & BIT(18) which is
0, so the updated value for val is always zero. Fix this by bitwise
and-ing value with the correct mask that will zero bits 16 and 18.
Addresses-Coverity: (" Suspicious &= or |= constant expression")
Fixes: b8eb71dcdd08 ("clk: sunxi-ng: Add A80 CCU")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
GPU PLL was designed with dynamic frequency switching in mind so driver
can adjust rate based on the GPU load.
Allow GPU clock to change parent rate (GPU PLL is the only possible
parent of GPU clock).
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
Audio devices needs exact clock rates in order to correctly reproduce
the sound. Until now, only integer factors were used to configure H6
audio PLL which resulted in inexact rates. Fix that by adding support
for fractional factors using sigma-delta modulation look-up table. It
contains values for two most commonly used audio base frequencies.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Acked-by: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Maxime Ripard <mripard@kernel.org>
|
|
into clk-next
- Set clk_init_data pointer inside clk_hw to NULL after registration
* clk-init-destroy:
clk: Overwrite clk_hw::init with NULL during clk_register()
clk: sunxi: Don't call clk_hw_get_name() on a hw that isn't registered
clk: ti: Don't reference clk_init_data after registration
clk: qcom: Remove error prints from DFS registration
rtc: sun6i: Don't reference clk_init_data after registration
clk: zx296718: Don't reference clk_init_data after registration
clk: milbeaut: Don't reference clk_init_data after registration
clk: socfpga: deindent code to proper indentation
phy: ti: am654-serdes: Don't reference clk_init_data after registration
clk: sprd: Don't reference clk_init_data after registration
clk: socfpga: Don't reference clk_init_data after registration
clk: sirf: Don't reference clk_init_data after registration
clk: qcom: Don't reference clk_init_data after registration
clk: meson: axg-audio: Don't reference clk_init_data after registration
clk: lochnagar: Don't reference clk_init_data after registration
clk: actions: Don't reference clk_init_data after registration
* clk-doc:
clk: remove extra ---help--- tags in Kconfig
clk: add include guard to clk-conf.h
clk: Document of_parse_clkspec() some more
clk: Remove extraneous 'for' word in comments
* clk-imx: (32 commits)
clk: imx: imx8mn: fix pll mux bit
clk: imx: imx8mm: fix pll mux bit
clk: imx: clk-pll14xx: unbypass PLL by default
clk: imx: pll14xx: avoid glitch when set rate
clk: imx: imx8mn: fix audio pll setting
clk: imx8mn: Add necessary frequency support for ARM PLL table
clk: imx8mn: Add missing rate_count assignment for each PLL structure
clk: imx8mn: fix int pll clk gate
clk: imx8mn: Add GIC clock
clk: imx8mn: Fix incorrect parents
clk: imx8mm: Fix incorrect parents
clk: imx8mq: Fix sys3 pll references
clk: imx8mq: Unregister clks when of_clk_add_provider failed
clk: imx8mm: Unregister clks when of_clk_add_provider failed
clk: imx8mq: Mark AHB clock as critical
clk: imx8mn: Keep uart clocks on for early console
clk: imx: Remove unused function statement
clk: imx7ulp: Make sure earlycon's clock is enabled
clk: imx8mm: Switch to platform driver
clk: imx: imx8mm: fix audio pll setting
...
* clk-allwinner:
clk: sunxi-ng: h6: Allow I2S to change parent rate
clk: sunxi-ng: v3s: add Allwinner V3 support
clk: sunxi-ng: v3s: add missing clock slices for MMC2 module clocks
dt-bindings: clk: sunxi-ccu: add compatible string for V3 CCU
clk: sunxi-ng: v3s: add the missing PLL_DDR1
|
|
I2S doesn't work if parent rate couldn't be change. Difference between
wanted and actual rate is too big.
Fix this by adding CLK_SET_RATE_PARENT flag to I2S clocks.
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Marcus Cooper <codekipper@gmail.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
The implementation of clk_hw_get_name() relies on the clk_core
associated with the clk_hw pointer existing. If of_clk_hw_register()
fails, there isn't a clk_core created yet, so calling clk_hw_get_name()
here fails. Extract the name first so we can print it later.
Fixes: 1d80c14248d6 ("clk: sunxi-ng: Add common infrastructure")
Cc: Maxime Ripard <maxime.ripard@bootlin.com>
Cc: Chen-Yu Tsai <wens@csie.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Allwinner V3 has the same main die with V3s, but with more pins wired.
There's a I2S bus on V3 that is not available on V3s.
Add the V3-only peripheral's clocks and reset to the V3s CCU driver,
bound to a new V3 compatible string. The driver name is not changed
because it's part of the device tree binding (the header file name).
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The MMC2 clock slices are currently not defined in V3s CCU driver, which
makes MMC2 not working.
Fix this issue.
Fixes: d0f11d14b0bc ("clk: sunxi-ng: add support for V3s CCU")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The user manual of V3/V3s/S3 declares a PLL_DDR1, however it's forgot
when developing the V3s CCU driver.
Add back the missing PLL_DDR1.
Fixes: d0f11d14b0bc ("clk: sunxi-ng: add support for V3s CCU")
Signed-off-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"This round of clk driver and framework updates is heavy on the driver
update side. The two main highlights in the core framework are the
addition of an bulk clk_get API that handles optional clks and an
extra debugfs file that tells the developer about the current parent
of a clk.
The driver updates are dominated by i.MX in the diffstat, but that is
mostly because that SoC has started converting to the clk_hw style of
clk registration. The next big update is in the Amlogic meson clk
driver that gained some support for audio, cpu, and temperature clks
while fixing some PLL issues. Finally, the biggest thing that stands
out is the conversion of a large part of the Allwinner sunxi-ng driver
to the new clk parent scheme that uses less strings and more pointer
comparisons to match clk parents and children up.
In general, it looks like we have a lot of little fixes and tweaks
here and there to clk data along with the normal addition of a handful
of new drivers and a couple new core framework features.
Core:
- Add a 'clk_parent' file in clk debugfs
- Add a clk_bulk_get_optional() API (with devm too)
New Drivers:
- Support gated clk controller on MIPS based BCM63XX SoCs
- Support SiLabs Si5341 and Si5340 chips
- Support for CPU clks on Raspberry Pi devices
- Audsys clock driver for MediaTek MT8516 SoCs
Updates:
- Convert a large portion of the Allwinner sunxi-ng driver to new clk parent scheme
- Small frequency support for SiLabs Si544 chips
- Slow clk support for AT91 SAM9X60 SoCs
- Remove dead code in various clk drivers (-Wunused)
- Support for Marvell 98DX1135 SoCs
- Get duty cycle of generic pwm clks
- Improvement in mmc phase calculation and cleanup of some rate defintions
- Switch i.MX6 and i.MX7 clock drivers to clk_hw based APIs
- Add GPIO, SNVS and GIC clocks for i.MX8 drivers
- Mark imx6sx/ul/ull/sll MMDC_P1_IPG and imx8mm DRAM_APB as critical clock
- Correct imx7ulp nic1_bus_clk and imx8mm audio_pll2_clk clock setting
- Add clks for new Exynos5422 Dynamic Memory Controller driver
- Clock definition for Exynos4412 Mali
- Add CMM (Color Management Module) clocks on Renesas R-Car H3, M3-N, E3, and D3
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas RZ/G2M
- Support for 32 bit clock IDs in TI's sci-clks for J721e SoCs
- TI clock probing done from DT by default instead of firmware
- Fix Amlogic Meson mpll fractional part and spread sprectrum issues
- Add Amlogic meson8 audio clocks
- Add Amlogic g12a temperature sensors clocks
- Add Amlogic g12a and g12b cpu clocks
- Add TPU (Timer Pulse Unit / PWM) clocks on Renesas R-Car H3, M3-W, and M3-N
- Add CMM (Color Management Module) clocks on Renesas R-Car M3-W
- Add Clock Domain support on Renesas RZ/N1"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (190 commits)
clk: consoldiate the __clk_get_hw() declarations
clk: sprd: Add check for return value of sprd_clk_regmap_init()
clk: lochnagar: Update DT binding doc to include the primary SPDIF MCLK
clk: Add Si5341/Si5340 driver
dt-bindings: clock: Add silabs,si5341
clk: clk-si544: Implement small frequency change support
clk: add BCM63XX gated clock controller driver
devicetree: document the BCM63XX gated clock bindings
clk: at91: sckc: use dedicated functions to unregister clock
clk: at91: sckc: improve error path for sama5d4 sck registration
clk: at91: sckc: remove unnecessary line
clk: at91: sckc: improve error path for sam9x5 sck register
clk: at91: sckc: add support to free slow clock osclillator
clk: at91: sckc: add support to free slow rc oscillator
clk: at91: sckc: add support to free slow oscillator
clk: rockchip: export HDMIPHY clock on rk3228
clk: rockchip: add watchdog pclk on rk3328
clk: rockchip: add clock id for hdmi_phy special clock on rk3228
clk: rockchip: add clock id for watchdog pclk on rk3328
clk: at91: sckc: add support for SAM9X60
...
|
|
https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into clk-allwinner
Pull Allwinner sunxi-ng clk driver parent relation rewrite part 1 - take 2
from Chen-Yu Tsai:
"The first part of ongoing work to convert the sunxi-ng clk driver from
using global clock name strings to describe clk parenting, to having
direct struct clk_hw pointers, or local names based on clock-names from
the device tree binding.
This is based on Stephen Boyd's recent work allowing clk drivers to
specify clk parents using struct clk_hw * or parsing DT phandles in the
clk node.
This series can be split into a few major parts:
1) The first patch is a small fix for clk debugfs representation.
2) A bunch of CLK_HW_INIT_* helper macros are added. These cover the
situations I encountered, or assume I will encounter, such as single
internal (struct clk_hw *) parent, single DT (struct clk_parent_data
.fw_name), multiple internal parents, and multiple mixed (internal +
DT) parents. A special variant for just an internal single parent is
added, CLK_HW_INIT_HWS, which lets the driver share the singular
list, instead of having the compiler create a compound literal every
time. It might even make sense to only keep this variant.
3) A bunch of CLK_FIXED_FACTOR_* helper macros are added. The rationale
is the same as the single parent CLK_HW_INIT_* helpers.
4) Bulk conversion of CLK_FIXED_FACTOR to use local parent references,
either struct clk_hw * or DT .fw_name types, whichever the hardware
requires.
5) The beginning of SUNXI_CCU_GATE conversion to local parent
references. This part is not done. They are included as justification
and examples for the shared list of clk parents case."
* tag 'sunxi-ng-parent-rewrite-part-1-take-2' of https://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (25 commits)
clk: sunxi-ng: sun8i-r: Use local parent references for SUNXI_CCU_GATE
clk: sunxi-ng: a80-usb: Use local parent references for SUNXI_CCU_GATE
clk: sunxi-ng: gate: Add macros for referencing local clock parents
clk: sunxi-ng: h6-r: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: h6: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: a64: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: f1c100s: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: sun8i-r: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: v3s: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: r40: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: h3: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: a33: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: a23: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: a31: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: sun5i: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: a10: Use local parent references for CLK_FIXED_FACTOR
clk: sunxi-ng: sun8i-r: Use local parent references for CLK_HW_INIT_*
clk: sunxi-ng: switch to of_clk_hw_register() for registering clks
clk: fixed-factor: Add CLK_FIXED_FACTOR_FW_NAME for DT clock-names parent
clk: fixed-factor: Add CLK_FIXED_FACTOR_HWS which takes list of struct clk_hw *
...
|
|
With the new clk parenting code and SUNXI_CCU_GATE macros, we can
reference parents locally via pointers to struct clk_hw or DT
clock-names.
Convert existing SUNXI_CCU_GATE definitions to SUNXI_CCU_GATE_HWS
as the parent clock is internal to this clock unit.
To avoid duplication of clock definitions, we fix up the parent
reference for A83T in the A83T init function.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
With the new clk parenting code and SUNXI_CCU_GATE macros, we can
reference parents locally via pointers to struct clk_hw or DT
clock-names.
Convert existing SUNXI_CCU_GATE definitions to SUNXI_CCU_GATE_DATA to
specify the parent clock.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
With the new clk parenting code, clk_init_data was expanded to include
.parent_hws, for clk drivers to directly reference parents by clk_hw,
and .parent_data, for clk drivers to specify parents using a combination
of device tree clock-names, pointers to struct clk_hw, device tree clocks,
and/or fallback global clock names.
Add four new macros:
- SUNXI_CCU_GATE_HW, that can take a struct clk_hw pointer, instead
of a string, as its parent.
- SUNXI_CCU_GATE_FW that takes a string to match a clock-names entry
in the device tree to specify the clock parent.
- SUNXI_CCU_GATE_HWS that takes an array of struct clk_hw * as its
parent. This allows the array to be shared with other clk
declarations.
- SUNXI_CCU_GATE_DATA that takes an array of struct clk_parent_data *
as its parent. This allows the array to be shared with other clk
declarations.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
With the new clk parenting code and CLK_FIXED_FACTOR_{HW,FW_NAME}
macros, we can reference parents locally via pointers to struct clk_hw
or DT clock-names.
Convert existing CLK_FIXED_FACTOR definitions to either the _HW or
_FW_NAME variant based on whether the parent clock is internal or
external to the CCU.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
With the new clk parenting code and CLK_FIXED_FACTOR_{HW,FW_NAME}
macros, we can reference parents locally via pointers to struct clk_hw
or DT clock-names.
Convert existing CLK_FIXED_FACTOR definitions to either the _HW or
_FW_NAME variant based on whether the parent clock is internal or
external to the CCU.
A forward declaration for struct clk_fixed_factor pll_periph0_4x_clk
is added as the definitions of the fixed factor clocks appear much later
in the file. The position of fixed factor clock definitions will be
moved for all drivers at a later time, before the conversion of all
other clock types.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
|
With the new clk parenting code and CLK_FIXED_FACTOR_{HW,FW_NAME}
macros, we can reference parents locally via pointers to struct clk_hw
or DT clock-names.
Convert existing CLK_FIXED_FACTOR definitions to either the _HW or
_FW_NAME variant based on whether the parent clock is internal or
external to the CCU.
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
|
