| Age | Commit message (Collapse) | Author |
|---|
|
When support for EEH on PowerNV was added a lot of pseries specific code
was made "generic" and some of the quirks of pseries EEH came along for the
ride. One of the stranger quirks is eeh_pe containing two types of PE
address: pe->addr and pe->config_addr. There reason for this appears to be
historical baggage rather than any real requirements.
On pseries EEH PEs are manipulated using RTAS calls. Each EEH RTAS call
takes a "PE configuration address" as an input which is used to identify
which EEH PE is being manipulated by the call. When initialising the EEH
state for a device the first thing we need to do is determine the
configuration address for the PE which contains the device so we can enable
EEH on that PE. This process is outlined in PAPR which is the modern
(i.e post-2003) FW specification for pseries. However, EEH support was
first described in the pSeries RISC Platform Architecture (RPA) and
although they are mostly compatible EEH is one of the areas where they are
not.
The major difference is that RPA doesn't actually have the concept of a PE.
On RPA systems the EEH RTAS calls are done on a per-device basis using the
same config_addr that would be passed to the RTAS functions to access PCI
config space (e.g. ibm,read-pci-config). The config_addr is not identical
since the function and config register offsets of the config_addr must be
set to zero. EEH operations being done on a per-device basis doesn't make a
whole lot of sense when you consider how EEH was implemented on legacy PCI
systems.
For legacy PCI(-X) systems EEH was implemented using special PCI-PCI
bridges which contained logic to detect errors and freeze the secondary
bus when one occurred. This means that the EEH enabled state is shared
among all devices behind that EEH bridge. As a result there's no way to
implement the per-device control required for the semantics specified by
RPA. It can be made to work if we assume that a separate EEH bridge exists
for each EEH capable PCI slot and there are no bridges behind those slots.
However, RPA also specifies the ibm,configure-bridge RTAS call for
re-initalising bridges behind EEH capable slots after they are reset due
to an EEH event so that is probably not a valid assumption. This
incoherence was fixed in later PAPR, which succeeded RPA. Unfortunately,
since Linux EEH support seems to have been implemented based on the RPA
spec some of the legacy assumptions were carried over (probably for POWER4
compatibility).
The fix made in PAPR was the introduction of the "PE" concept and
redefining the EEH RTAS calls (set-eeh-option, reset-slot, etc) to operate
on a per-PE basis so all devices behind an EEH bride would share the same
EEH state. The "config_addr" argument to the EEH RTAS calls became the
"PE_config_addr" and the OS was required to use the
ibm,get-config-addr-info RTAS call to find the correct PE address for the
device. When support for the new interfaces was added to Linux it was
implemented using something like:
At probe time:
pdn->eeh_config_addr = rtas_config_addr(pdn);
pdn->eeh_pe_config_addr = rtas_get_config_addr_info(pdn);
When performing an RTAS call:
config_addr = pdn->eeh_config_addr;
if (pdn->eeh_pe_config_addr)
config_addr = pdn->eeh_pe_config_addr;
rtas_call(..., config_addr, ...);
In other words, if the ibm,get-config-addr-info RTAS call is implemented
and returned a valid result we'd use that as the argument to the EEH
RTAS calls. If not, Linux would fall back to using the device's
config_addr. Over time these addresses have moved around going from pci_dn
to eeh_dev and finally into eeh_pe. Today the users look like this:
config_addr = pe->config_addr;
if (pe->addr)
config_addr = pe->addr;
rtas_call(..., config_addr, ...);
However, considering the EEH core always operates on a per-PE basis and
even on pseries the only per-device operation is the initial call to
ibm,set-eeh-option I'm not sure if any of this actually works on an RPA
system today. It doesn't make much sense to have the fallback address in
a generic structure either since the bulk of the code which reference it
is in pseries anyway.
The EEH core makes a token effort to support looking up a PE using the
config_addr by having two arguments to eeh_pe_get(). However, a survey of
all the callers to eeh_pe_get() shows that all bar one have the config_addr
argument hard-coded to zero.The only caller that doesn't is in
eeh_pe_tree_insert() which has:
if (!eeh_has_flag(EEH_VALID_PE_ZERO) && !edev->pe_config_addr)
return -EINVAL;
pe = eeh_pe_get(hose, edev->pe_config_addr, edev->bdfn);
The third argument (config_addr) is only used if the second (pe->addr)
argument is invalid. The preceding check ensures that the call to
eeh_pe_get() will never happen if edev->pe_config_addr is invalid so there
is no situation where eeh_pe_get() will search for a PE based on the 3rd
argument. The check also means that we'll never insert a PE into the tree
where pe_config_addr is zero since EEH_VALID_PE_ZERO is never set on
pseries. All the users of the fallback address on pseries never actually
use the fallback and all the only caller that supplies something for the
config_addr argument to eeh_pe_get() never use it either. It's all dead
code.
This patch removes the fallback address from eeh_pe since nothing uses it.
Specificly, we do this by:
1) Removing pe->config_addr
2) Removing the EEH_VALID_PE_ZERO flag
3) Removing the fallback address argument to eeh_pe_get().
4) Removing all the checks for pe->addr being zero in the pseries EEH code.
This leaves us with PE's only being identified by what's in their pe->addr
field and the EEH core relying on the platform to ensure that eeh_dev's are
only inserted into the EEH tree if they're actually inside a PE.
No functional changes, I hope.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200918093050.37344-9-oohall@gmail.com
|
|
The initialisation of EEH mostly happens in a core_initcall_sync initcall,
followed by registering a bus notifier later on in an arch_initcall.
Anything involving initcall dependecies is mostly incomprehensible unless
you've spent a while staring at code so here's the full sequence:
ppc_md.setup_arch <-- pci_controllers are created here
...time passes...
core_initcall <-- pci_dns are created from DT nodes
core_initcall_sync <-- platforms call eeh_init()
postcore_initcall <-- PCI bus type is registered
postcore_initcall_sync
arch_initcall <-- EEH pci_bus notifier registered
subsys_initcall <-- PHBs are scanned here
There's no real requirement to do the EEH setup at the core_initcall_sync
level. It just needs to be done after pci_dn's are created and before we
start scanning PHBs. Simplify the flow a bit by moving the platform EEH
inititalisation to an arch_initcall so we can fold the bus notifier
registration into eeh_init().
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200918093050.37344-5-oohall@gmail.com
|
|
Fold pnv_eeh_init() into eeh_powernv_init() rather than having eeh_init()
call it via eeh_ops->init(). It's simpler and it'll let us delete
eeh_ops.init.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200918093050.37344-2-oohall@gmail.com
|
|
Drop the EEH register / unregister ops thing and have the platform pass the
ops structure into eeh_init() directly. This takes one initcall out of the
EEH setup path and it means we're only doing EEH setup on the platforms
which actually support it. It's also less code and generally easier to
follow.
No functional changes.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200918093050.37344-1-oohall@gmail.com
|
|
There's a few scattered in the powernv platform.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200804005410.146094-4-oohall@gmail.com
|
|
The EEH core has a concept of a "PE tree" to support PowerNV. The PE tree
follows the PCI bus structures because a reset asserted on an upstream
bridge will be propagated to the downstream bridges. On pseries there's a
1-1 correspondence between what the guest sees are a PHB and a PE so the
"tree" is really just a single node.
Current the EEH core is reponsible for setting up this PE tree which it
does by traversing the pci_dn tree. The structure of the pci_dn tree
matches the bus tree on PowerNV which leads to the PE tree being "correct"
this setup method doesn't make a whole lot of sense and it's actively
confusing for the pseries case where it doesn't really do anything.
We want to remove the dependence on pci_dn anyway so this patch move
choosing where to insert a new PE into the platform code rather than
being part of the generic EEH code. For PowerNV this simplifies the
tree building logic and removes the use of pci_dn. For pseries we
keep the existing logic. I'm not really convinced it does anything
due to the 1-1 PE-to-PHB correspondence so every device under that
PHB should be in the same PE, but I'd rather not remove it entirely
until we've had a chance to look at it more deeply.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-14-oohall@gmail.com
|
|
The naming of eeh_{add_to|remove_from}_parent_pe() doesn't really reflect
what they actually do. If the PE referred to be edev->pe_config_addr
already exists under that PHB then the edev is added to that PE. However,
if the PE doesn't exist the a new one is created for the edev.
The bulk of the implementation of eeh_add_to_parent_pe() covers that
second case. Similarly, most of eeh_remove_from_parent_pe() is
determining when it's safe to delete a PE.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-12-oohall@gmail.com
|
|
The edev->class_code field is never referenced anywhere except for the
platform specific probe functions. The same information is available in
the pci_dev for PowerNV and in the pci_dn on pseries so we can remove
the field.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-11-oohall@gmail.com
|
|
Mechanical conversion of the eeh_ops interfaces to use eeh_dev to reference
a specific device rather than pci_dn. No functional changes.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-9-oohall@gmail.com
|
|
Mechanical conversion of the eeh_ops interfaces to use eeh_dev to reference
a specific device rather than pci_dn. No functional changes.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-7-oohall@gmail.com
|
|
There's a bunch of strange things about this code. First up is that none of
the fields being written to are functional for a VF. The SR-IOV
specification lists then as "Reserved, but OS should preserve" so writing
new values to them doesn't do anything and is clearly wrong from a
correctness perspective.
However, since VFs are designed to be managed by the OS there is an
argument to be made that we should be saving and restoring some parts of
config space. We already sort of do that by saving the first 64 bytes of
config space in the eeh_dev (see eeh_dev->config_space[]). This is
inadequate since it doesn't even consider saving and restoring the PCI
capability structures. However, this is a problem with EEH in general and
that needs to be fixed for non-VF devices too.
There's no real reason to keep around this around so delete it.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-6-oohall@gmail.com
|
|
This is used in precisely one place which is in pseries specific platform
code. There's no need to have the callback in eeh_ops since the platform
chooses the EEH PE addresses anyway. The PowerNV implementation has always
been a stub too so remove it.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200725081231.39076-5-oohall@gmail.com
|
|
With the EEH early probe now being pseries specific there's no need for
eeh_ops->probe() to take a pci_dn. Instead, we can make it take a pci_dev
and use the probe function to map a pci_dev to an eeh_dev. This allows
the platform to implement it's own method for finding (or creating) an
eeh_dev for a given pci_dev which also removes a use of pci_dn in
generic EEH code.
This patch also renames eeh_device_add_late() to eeh_device_probe(). This
better reflects what it does does and removes the last vestiges of the
early/late EEH probe split.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-6-oohall@gmail.com
|
|
The eeh_ops->probe() function is called from two different contexts:
1. On pseries, where we set EEH_PROBE_MODE_DEVTREE, it's called in
eeh_add_device_early() which is supposed to run before we create
a pci_dev.
2. On PowerNV, where we set EEH_PROBE_MODE_DEV, it's called in
eeh_device_add_late() which is supposed to run *after* the
pci_dev is created.
The "early" probe is required because PAPR requires that we perform an RTAS
call to enable EEH support on a device before we start interacting with it
via config space or MMIO. This requirement doesn't exist on PowerNV and
shoehorning two completely separate initialisation paths into a common
interface just results in a convoluted code everywhere.
Additionally the early probe requires the probe function to take an pci_dn
rather than a pci_dev argument. We'd like to make pci_dn a pseries specific
data structure since there's no real requirement for them on PowerNV. To
help both goals move the early probe into the pseries containment zone
so the platform depedence is more explicit.
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-5-oohall@gmail.com
|
|
Move creating the EEH specific sysfs files into eeh_add_device_late()
rather than being open-coded all over the place. Calling the function is
generally done immediately after calling eeh_add_device_late() anyway. This
is also a correctness fix since currently the sysfs files will be added
even if the EEH probe happens to fail.
Similarly, on pseries we currently add the sysfs files before calling
eeh_add_device_late(). This is flat-out broken since the sysfs files
require the pci_dev->dev.archdata.edev pointer to be set, and that is done
in eeh_add_device_late().
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20200306073904.4737-1-oohall@gmail.com
|
|
Recent cleanup in the way EEH support is added to a device causes a
kernel oops when the cxl driver probes a device and creates virtual
devices discovered on the FPGA:
BUG: Kernel NULL pointer dereference at 0x000000a0
Faulting instruction address: 0xc000000000048070
Oops: Kernel access of bad area, sig: 7 [#1]
...
NIP eeh_add_device_late.part.9+0x50/0x1e0
LR eeh_add_device_late.part.9+0x3c/0x1e0
Call Trace:
_dev_info+0x5c/0x6c (unreliable)
pnv_pcibios_bus_add_device+0x60/0xb0
pcibios_bus_add_device+0x40/0x60
pci_bus_add_device+0x30/0x100
pci_bus_add_devices+0x64/0xd0
cxl_pci_vphb_add+0xe0/0x130 [cxl]
cxl_probe+0x504/0x5b0 [cxl]
local_pci_probe+0x6c/0x110
work_for_cpu_fn+0x38/0x60
The root cause is that those cxl virtual devices don't have a
representation in the device tree and therefore no associated pci_dn
structure. In eeh_add_device_late(), pdn is NULL, so edev is NULL and
we oops.
We never had explicit support for EEH for those virtual devices.
Instead, EEH events are reported to the (real) pci device and handled
by the cxl driver. Which can then forward to the virtual devices and
handle dependencies. The fact that we try adding EEH support for the
virtual devices is new and a side-effect of the recent cleanup.
This patch fixes it by skipping adding EEH support on powernv for
devices which don't have a pci_dn structure.
The cxl driver doesn't create virtual devices on pseries so this patch
doesn't fix it there intentionally.
Fixes: b905f8cdca77 ("powerpc/eeh: EEH for pSeries hot plug")
Signed-off-by: Frederic Barrat <fbarrat@linux.ibm.com>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20191016162833.22509-1-fbarrat@linux.ibm.com
|
|
When we reset PCI devices managed by a hotplug driver the reset may
generate spurious hotplug events that cause the PCI device we're resetting
to be torn down accidently. This is a problem for EEH (when the driver is
EEH aware) since we want to leave the OS PCI device state intact so that
the device can be re-set without losing any resources (network, disks,
etc) provided by the driver.
Generic PCI code provides the pci_bus_error_reset() function to handle
resetting a PCI Device (or bus) by using the reset method provided by the
hotplug slot driver. We can use this function if the EEH core has
requested a hot reset (common case) without tripping over the hotplug
driver.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-8-oohall@gmail.com
|
|
Support for switching CAPI cards into and out of CAPI mode was removed a
while ago. Drop the comment since it's no longer relevant.
Signed-off-by: Oliver O'Halloran <oohall@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/20190903101605.2890-7-oohall@gmail.com
|
|
Convert existing messages, where appropriate, to use the eeh_edev_*
logging macros.
The only effect should be minor adjustments to the log messages, apart
from:
- A new message in pseries_eeh_probe() "Probing device" to match the
powernv case.
- The "Probing device" message in pnv_eeh_probe() is now generated
slightly later, which will mean that it is no longer emitted for
devices that aren't probed due to the initial checks.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/ce505a0a7a4a5b0367f0f40f8b26e7c0a9cf4cb7.1565930772.git.sbobroff@linux.ibm.com
|
|
Now that EEH support for all devices (on PowerNV and pSeries) is
provided by the pcibios bus add device hooks, eeh_probe_devices() and
eeh_addr_cache_build() are redundant and can be removed.
Move the EEH enabled message into it's own function so that it can be
called from multiple places.
Note that previously on pSeries, useless EEH sysfs files were created
for some devices that did not have EEH support and this change
prevents them from being created.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/33b0a6339d5ac88693de092d6fba984f2a5add66.1565930772.git.sbobroff@linux.ibm.com
|
|
On PowerNV and pSeries, devices currently acquire EEH support from
several different places: Boot-time devices from eeh_probe_devices()
and eeh_addr_cache_build(), Virtual Function devices from the pcibios
bus add device hooks and hot plugged devices from pci_hp_add_devices()
(with other platforms using other methods as well). Unfortunately,
pSeries machines currently discover hot plugged devices using
pci_rescan_bus(), not pci_hp_add_devices(), and so those devices do
not receive EEH support.
Rather than adding another case for pci_rescan_bus(), this change
widens the scope of the pcibios bus add device hooks so that they can
handle all devices. As a side effect this also supports devices
discovered after manually rescanning via /sys/bus/pci/rescan.
Note that on PowerNV, this change allows the EEH subsystem to become
enabled after boot as long as it has not been forced off, which was
not previously possible (it was already possible on pSeries).
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/72ae8ae9c54097158894a52de23690448de38ea9.1565930772.git.sbobroff@linux.ibm.com
|
|
Also remove useless comment.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
Link: https://lore.kernel.org/r/59db84f4bf94718a12f206bc923ac797d47e4cc1.1565930772.git.sbobroff@linux.ibm.com
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Notable changes:
- Removal of the NPU DMA code, used by the out-of-tree Nvidia driver,
as well as some other functions only used by drivers that haven't
(yet?) made it upstream.
- A fix for a bug in our handling of hardware watchpoints (eg. perf
record -e mem: ...) which could lead to register corruption and
kernel crashes.
- Enable HAVE_ARCH_HUGE_VMAP, which allows us to use large pages for
vmalloc when using the Radix MMU.
- A large but incremental rewrite of our exception handling code to
use gas macros rather than multiple levels of nested CPP macros.
And the usual small fixes, cleanups and improvements.
Thanks to: Alastair D'Silva, Alexey Kardashevskiy, Andreas Schwab,
Aneesh Kumar K.V, Anju T Sudhakar, Anton Blanchard, Arnd Bergmann,
Athira Rajeev, Cédric Le Goater, Christian Lamparter, Christophe
Leroy, Christophe Lombard, Christoph Hellwig, Daniel Axtens, Denis
Efremov, Enrico Weigelt, Frederic Barrat, Gautham R. Shenoy, Geert
Uytterhoeven, Geliang Tang, Gen Zhang, Greg Kroah-Hartman, Greg Kurz,
Gustavo Romero, Krzysztof Kozlowski, Madhavan Srinivasan, Masahiro
Yamada, Mathieu Malaterre, Michael Neuling, Nathan Lynch, Naveen N.
Rao, Nicholas Piggin, Nishad Kamdar, Oliver O'Halloran, Qian Cai, Ravi
Bangoria, Sachin Sant, Sam Bobroff, Satheesh Rajendran, Segher
Boessenkool, Shaokun Zhang, Shawn Anastasio, Stewart Smith, Suraj
Jitindar Singh, Thiago Jung Bauermann, YueHaibing"
* tag 'powerpc-5.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (163 commits)
powerpc/powernv/idle: Fix restore of SPRN_LDBAR for POWER9 stop state.
powerpc/eeh: Handle hugepages in ioremap space
ocxl: Update for AFU descriptor template version 1.1
powerpc/boot: pass CONFIG options in a simpler and more robust way
powerpc/boot: add {get, put}_unaligned_be32 to xz_config.h
powerpc/irq: Don't WARN continuously in arch_local_irq_restore()
powerpc/module64: Use symbolic instructions names.
powerpc/module32: Use symbolic instructions names.
powerpc: Move PPC_HA() PPC_HI() and PPC_LO() to ppc-opcode.h
powerpc/module64: Fix comment in R_PPC64_ENTRY handling
powerpc/boot: Add lzo support for uImage
powerpc/boot: Add lzma support for uImage
powerpc/boot: don't force gzipped uImage
powerpc/8xx: Add microcode patch to move SMC parameter RAM.
powerpc/8xx: Use IO accessors in microcode programming.
powerpc/8xx: replace #ifdefs by IS_ENABLED() in microcode.c
powerpc/8xx: refactor programming of microcode CPM params.
powerpc/8xx: refactor printing of microcode patch name.
powerpc/8xx: Refactor microcode write
powerpc/8xx: refactor writing of CPM microcode arrays
...
|
|
If the previous comment made sense, continue debugging or call your
doctor immediately.
Signed-off-by: Stewart Smith <stewart@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
opal_pci_eeh_freeze_status
The current implementation of the OPAL_PCI_EEH_FREEZE_STATUS call in
skiboot's NPU driver does not touch the pci_error_type parameter so
it might have garbage but the powernv code analyzes it nevertheless.
This initializes pcierr and fstate to zero in all call sites.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The wait_state member of eeh_ops does not need to be platform
dependent; it's just logic around eeh_ops.get_state(). Therefore,
merge the two (slightly different!) platform versions into a new
function, eeh_wait_state() and remove the eeh_ops member.
While doing this, also correct:
* The wait logic, so that it never waits longer than max_wait.
* The wait logic, so that it never waits less than
EEH_STATE_MIN_WAIT_TIME.
* One call site where the result is treated like a bit field before
it's checked for negative error values.
* In pseries_eeh_get_state(), rename the "state" parameter to "delay"
because that's what it is.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently, eeh_pe_state_mark() marks a PE (and it's children) with a
state and then performs additional processing if that state included
EEH_PE_ISOLATED.
The state parameter is always a constant at the call site, so
rearrange eeh_pe_state_mark() into two functions and just call the
appropriate one at each site.
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Instances of struct eeh_pe are placed in a tree structure using the
fields "child_list" and "child", so place these next to each other
in the definition.
The field "child" is a list entry, so remove the unnecessary and
misleading use of the list initializer, LIST_HEAD(), on it.
The eeh_dev struct contains two list entry fields, called "list" and
"rmv_list". Rename them to "entry" and "rmv_entry" and, as above, stop
initializing them with LIST_HEAD().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Currently a flag, EEH_POSTPONED_PROBE, is used to prevent an incorrect
message "EEH: No capable adapters found" from being displayed during
the boot of powernv systems.
It is necessary because, on powernv, the call to eeh_probe_devices()
made from eeh_init() is too early and EEH can't yet be enabled. A
second call is made later from eeh_pnv_post_init(), which succeeds.
(On pseries, the first call succeeds because PCI devices are set up
early enough and no second call is made.)
This can be simplified by moving the early call to eeh_probe_devices()
from eeh_init() (where it's seen by both platforms) to
pSeries_final_fixup(), so that each platform only calls
eeh_probe_devices() once, at a point where it can succeed.
This is slightly later in the boot sequence, but but still early
enough and it is now in the same place in the sequence for both
platforms (the pcibios_fixup hook).
The display of the message can be cleaned up as well, by moving it
into eeh_probe_devices().
Signed-off-by: Sam Bobroff <sbobroff@linux.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Due to recent refactoring in EEH in:
commit b9fde58db7e5 ("powerpc/powernv: Rework EEH initialization on
powernv")
a misleading message was seen in the kernel message buffer:
[ 0.108431] EEH: PowerNV platform initialized
[ 0.589979] EEH: No capable adapters found
This happened due to the removal of the initialization delay for powernv
platform.
Even though the EEH infrastructure for the devices is eventually
initialized and still works just fine the eeh device probe step is
postponed in order to assure the PEs are created. Later
pnv_eeh_post_init does the probe devices job but at that point the
message was already shown right after eeh_init flow.
This patch introduces a new flag EEH_POSTPONED_PROBE to represent that
temporary state and avoid the message mentioned above and showing the
follow one instead:
[ 0.107724] EEH: PowerNV platform initialized
[ 4.844825] EEH: PCI Enhanced I/O Error Handling Enabled
Signed-off-by: Mauro S. M. Rodrigues <maurosr@linux.vnet.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Tested-by:Venkat Rao B <vrbagal1@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Checking for a "fully active" device state requires testing two flag
bits, which is open coded in several places, so add a function to do
it.
Signed-off-by: Sam Bobroff <sam.bobroff@au1.ibm.com>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When pseries SR-IOV is enabled and after a PF driver has resumed from
EEH, platform has to be notified of the event so the child VFs can be
allowed to resume their normal recovery path.
This patch makes the EEH operation allow unfreeze platform dependent
code and adds the call to pseries EEH code.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@linux.vnet.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Add EEH platform operations for pseries to update VF config space.
With this change after EEH, the VF will have updated config space for
pseries platform.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@linux.vnet.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
SR-IOV can now be enabled for the powernv platform and pseries
platform. Therefore move the appropriate calls to machine dependent
code instead of relying on definition at compile time.
Signed-off-by: Bryant G. Ly <bryantly@linux.vnet.ibm.com>
Signed-off-by: Juan J. Alvarez <jjalvare@us.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Remove the post_init callback which is only used
by powernv, we can just call it explicitly from
the powernv code.
This partially kills the ability to "disable" eeh at
runtime via debugfs as this was calling that same
callback again, but this is both unused and broken
in several ways. If we want to revive it, we need
to create a dedicated enable/disable callback on the
backend that does the right thing.
Let the bulk of eeh initialize normally at
core_initcall() like it does on pseries by removing
the hack in eeh_init() that delays it.
Instead we make sure our eeh->probe cleanly bails
out of the PEs haven't been created yet and we force
a re-probe where we used to call eeh_init() again.
Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The eeh_dev struct hold a config space address of an associated node
and the very same address is also stored in the pci_dn struct which
is always present during the eeh_dev lifetime.
This uses bus:devfn directly from pci_dn instead of cached and packed
config_addr.
Since config_addr is made from device's bus:dev.fn, there is no point
in keeping it in the debugfs either so remove that too.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The eeh_dev struct already holds a pointer to pci_dn which it does not
exist without and pci_dn itself holds the very same pointer so just
use it.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
arch/powerpc/kernel/eeh_dev.c:57 is the only legit place where edev
is allocated; other 2 places allocate it on stack and in the heap for
a very short period of time to use eeh_pe_get() as takes edev.
This changes eeh_pe_get() to receive required parameters explicitly.
This removes unnecessary temporary allocation of edev.
This uses the "pe_no" name instead of the "pe_config_addr" name as
it actually is a PE number and not a config space address as it seemed.
Signed-off-by: Alexey Kardashevskiy <aik@ozlabs.ru>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Acked-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Diagnostic data for PHBs currently works by allocated a fixed-sized buffer.
This is simple, but either wastes memory (though only a few kilobytes) or
in the case of PHB4 isn't enough to fit the whole data blob.
For machines that don't describe the diagnostic data size in the device
tree, use the hardcoded buffer size as before. For those that do, only
allocate exactly what's needed.
In the special case of P7IOC (which has two types of diag data), the larger
should be specified in the device tree.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
Similar to what is done in commit b6541db13952 ("powerpc/eeh: Block
PCI config access upon frozen PE"), we need block PCI config access
for BCM5719 when recovering frozen error on them. Otherwise, an
unexpected recursive fenced PHB error is observed.
0001:06:00.0 Ethernet controller: Broadcom Corporation \
NetXtreme BCM5718 Gigabit Ethernet PCIe (rev 10)
0001:06:00.1 Ethernet controller: Broadcom Corporation \
NetXtreme BCM5718 Gigabit Ethernet PCIe (rev 10)
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
pnv_eeh_reset() has special handling for PEs whose primary bus is the
root bus or the bus immediately underneath the root port.
The cxl bi-modal card support added in b0b5e5918ad1 ("cxl: Add
cxl_check_and_switch_mode() API to switch bi-modal cards") relies on
this behaviour when hot-resetting the CAPI adapter following a mode
switch. Document this in pnv_eeh_reset() so we don't accidentally break
it.
Suggested-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Reviewed-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
PHB, PE (and by association MVE) numbers are printed as a mix of decimal
and hexadecimal throughout the kernel. This can be misleading, so make
them all hexadecimal.
Standardising on hex instead of dec because:
- PHB numbers are presented in hex in sysfs/debugfs (and lspci, etc)
- PE numbers are presented as hex in sysfs and parsed in hex in debugfs
The only place I think this could cause confusing are the messages during
boot, i.e.
pci 000a:01 : [PE# 000] Secondary bus 1 associated with PE#0
which can be a quick way to check PE numbers. pe_level_printk() will
only print two characters instead of three, so the above would be
pci 000a:01 : [PE# 00] Secondary bus 1 associated with PE#0
which gives a hint it's in hex.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
pnv_eeh_get_and_dump_hub_diag()
The hub diag-data type is filled with big-endian data by OPAL call
opal_pci_get_hub_diag_data(). We need convert it to CPU-endian value
before using it. The issue is reported by sparse as pointed by Michael
Ellerman:
eeh-powernv.c:1309:21: warning: restricted __be16 degrades to integer
This converts hub diag-data type to CPU-endian before using it in
pnv_eeh_get_and_dump_hub_diag().
Fixes: 2a485ad7c88d ("powerpc/powernv: Drop PHB operation next_error()")
Cc: stable@vger.kernel.org # v4.1+
Suggested-by: Michael Ellerman <mpe@ellerman.id.au>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The PE number (@frozen_pe_no), filled by opal_pci_next_error() is in
big-endian format. It should be converted to CPU-endian before it is
passed to opal_pci_eeh_freeze_clear() when clearing the frozen state if
the PE is invalid one. As Michael Ellerman pointed out, the issue is
also detected by sparse:
eeh-powernv.c:1541:41: warning: incorrect type in argument 2 (different base types)
This passes CPU-endian PE number to opal_pci_eeh_freeze_clear() and it
should be part of commit <0f36db77643b> ("powerpc/eeh: Fix wrong printed
PE number"), which was merged to 4.3 kernel.
Fixes: 71b540adffd9 ("powerpc/powernv: Don't escalate non-existing frozen PE")
Cc: stable@vger.kernel.org # v4.3+
Suggested-by: Paul Mackerras <paulus@samba.org>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Reviewed-by: Russell Currey <ruscur@russell.cc>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When issuing PHB reset, OPAL API opal_pci_poll() is called to drive
the state machine in OPAL forward. However, we needn't always call
the function under some circumstances like reset deassert.
This avoids calling opal_pci_poll() when OPAL_SUCCESS is returned
from opal_pci_reset(). Except the overhead introduced by additional
one unnecessary OPAL call, I didn't run into real issue because of
this.
Reported-by: Pridhiviraj Paidipeddi <ppaiddipe@in.ibm.com>
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
When the PE used in pnv_eeh_reset() is that of a VF,
pnv_eeh_reset_vf_pe() is used. Unlike the other reset functions called
in pnv_eeh_reset(), the VF reset doesn't require a bus, and if a bus was
missing the function would error out before resetting the VF PE.
To avoid this, reorder the VF reset function to occur before finding and
checking the bus.
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
eeh_pe_bus_get() can return NULL if a PCI bus isn't found for a given PE.
Some callers don't check this, and can cause a null pointer dereference
under certain circumstances.
Fix this by checking NULL everywhere eeh_pe_bus_get() is called.
Fixes: 8a6b1bc70dbb ("powerpc/eeh: EEH core to handle special event")
Cc: stable@vger.kernel.org # v3.11+
Signed-off-by: Russell Currey <ruscur@russell.cc>
Reviewed-by: Andrew Donnellan <andrew.donnellan@au1.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The (OPAL) firmware might provide the PCI slot reset capability
which is identified by property "ibm,reset-by-firmware" on the
PCI slot associated device node.
This routes the reset request to firmware if "ibm,reset-by-firmware"
exists in the PCI slot device node. Otherwise, the reset is done
inside kernel as before.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
|
The reset and poll functionality from (OPAL) firmware supports
PHB and PCI slot at same time. They are identified by ID. This
supports PCI slot ID by:
* Rename the argument name for opal_pci_reset() and opal_pci_poll()
accordingly
* Rename pnv_eeh_phb_poll() to pnv_eeh_poll() and adjust its argument
name.
* One macro is added to produce PCI slot ID.
Signed-off-by: Gavin Shan <gwshan@linux.vnet.ibm.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
