summaryrefslogtreecommitdiff
path: root/arch/powerpc/boot
AgeCommit message (Collapse)Author
2008-01-25[POWERPC] 4xx: logical/bitand typo in powerpc/boot/4xx.cRoel Kluin
logical/bitand typo Signed-off-by: Roel Kluin <12o3l@tiscali.nl> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-01-25[POWERPC] 4xx: PIKA Warp bootwrapperSean MacLennan
Add the cuboot wrapper for the PIKA Warp board Signed-off-by: Sean MacLennan <smaclennan@pikatech.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-01-25[POWERPC] 4xx: PIKA Warp DTSSean MacLennan
Add the device tree for the PIKA Warp board Signed-off-by: Sean MacLennan <smaclennan@pikatech.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-01-25[POWERPC] Enable RTC for Ebony and Walnut (v2)David Gibson
This patch extends the Ebony and Walnut platform code to instantiate the existing ds1742 RTC class driver for the DS1743 RTC/NVRAM chip found on both those boards. The patch uses a helper function to scan the device tree and instantiate the appropriate platform_device based on it, so it should be easy to extend for other boards which have mmio mapped RTC chips. Along with this, the device tree binding for the ds1743 chips is tweaked, based on the existing DS1385 OF binding found at: http://playground.sun.com/1275/proposals/Closed/Remanded/Accepted/346-it.txt Although that document covers the NVRAM portion of the chip, whereas here we're interested in the RTC portion, so it's not entirely clear if that's a good model. This implements only RTC class driver support - that is /dev/rtc0, not /dev/rtc, and the low-level get/set time callbacks remain unimplemented. That means in order to get at the clock you will either need a modified version of hwclock which will look at /dev/rtc0, or you'll need to configure udev to symlink rtc0 to rtc. Signed-off-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-01-25[POWERPC] 4xx: Add AMCC Haleakala (405EXr) dtsStefan Roese
The patch adds the Haleakala dts. The Haleakala is a stripped down version of the Kilauea (405EX) with only one EMAC and only one PCIe interface. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2008-01-24Merge branch 'for-2.6.25' of ↵Paul Mackerras
master.kernel.org:/pub/scm/linux/kernel/git/galak/powerpc into for-2.6.25
2008-01-23[POWERPC] Add initial iomega StorCenter board port.Jon Loeliger
Use cuImage bootwrapper until U-Boot port is completed. Derived heavily from Linkstation port. Signed-off-by: Jon Loeliger <jdl@freescale.com> Acked-by: Andy Wilcox <andy@protium.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] Add StorCenter DTS first draft.Jon Loeliger
Based on the Kurobox DTS files. Signed-off-by: Jon Loeliger <jdl@freescale.com> Acked-by: Andy Wilcox <andy@protium.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] 86xx: Add localbus and flash nodes to mpc8641_hpcn.dtsWade Farnsworth
Add local bus, flash, and MTD partition nodes to mpc8641_hpcn.dts Also add compatible field for the soc node, so that it will be picked up by of_platform_bus_probe(). Signed-off-by: Wade Farnsworth <wfarnsworth@mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] 8xx: adder875 - Fix flash bus-width and remove duplicate __initdataScott Wood
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] 83xx: MPC8313e RDB - Add NOR flash to the device tree.Scott Wood
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] 83xx: MPC8313e RBD add NAND to device treeScott Wood
Add NAND to device tree, and call of_platform_bus_probe(). Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] 82xx: Embedded Planet EP8248E supportScott Wood
This board is also resold by Freescale under the names "QUICCStart MPC8248 Evaluation System" and "CWH-PPC-8248N-VE". Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] 8xx: Analogue & Micro Adder875 board support.Scott Wood
Signed-off-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] Update MPC8610 HPCD to support audio driversTimur Tabi
Update the MPC8610 HPCD files to support the audio driver. Update booting-without-of.txt with information on the SSI device. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] QE: Add support for Freescale QUICCEngine UARTTimur Tabi
Add support for UART serial ports using a Freescale QUICCEngine. Update booting-without-of.txt to define new properties for a QE UART node. Update the MPC8323E-MDS device tree to add UCC5 as a UART. Update the QE library to support slow UCC devices and modules. Signed-off-by: Timur Tabi <timur@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] MPC8349E-mITX: Vitesse 7385 PHY is not connected to the MDIO busVitaly Bordug
...thus use fixed-link to register proper "Fixed PHY" Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] MPC8349E-mITX: introduce localbus and pata nodesAnton Vorontsov
This patch adds localbus and pata nodes to use CF IDE interface on MPC8349E-mITX boards. Patch also adds code to probe localbus. Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] 83xx: USB device tree cleanupsLi Yang
Remove device_type = "usb" for 83xx SoC USB controller Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] 83xx: add device trees for MPC837x MDS boardLi Yang
Signed-off-by: Li Yang <leoli@freescale.com> Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] Fix incorrect interrupt map on FSL reference boardsKumar Gala
The ULI based boards had the interrupt maps for USB on the ULI incorrectly set. Also, the MPC8572DS was missing the interrupt-map-mask for the 3rd PCIe controller. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] bootwrapper: convert cuboot-8{3,5}xx to dt_fixup_mac_address_by_aliasKumar Gala
Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-23[POWERPC] bootwrapper: Add find_node_by_alias and dt_fixup_mac_address_by_aliasKumar Gala
Add the ability to set the mac address given the alias for the device. Removes the need for having a linux,network-index property. Signed-off-by: Kumar Gala <galak@kernel.crashing.org>
2008-01-24Merge branch 'linux-2.6'Paul Mackerras
2008-01-22Fix file references in documentation and KconfigJohann Felix Soden
Fix typo in arch/powerpc/boot/flatdevtree_env.h. There is no Documentation/networking/ixgbe.txt. README.cycladesZ is now in Documentation/. wavelan.p.h is now in drivers/net/wireless/. HFS.txt is now Documentation/filesystems/hfs.txt. OSS-files are now in sound/oss/. Signed-off-by: Johann Felix Soden <johfel@users.sourceforge.net> Acked-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2008-01-18[POWERPC] mpc5200: Add generic support for simple MPC5200 based boardsMarian Balakowicz
This patch adds support for 'mpc5200-simple-platform' compatible boards which do not need a platform specific setup. Such boards are supported assuming the following: - GPIO pins are configured by the firmware, - CDM configuration (clocking) is setup correctly by firmware, - if the 'fsl,has-wdt' property is present in one of the gpt nodes, then it is safe to use such gpt to reset the board, - PCI is supported if enabled in the kernel configuration and if there is a PCI bus node defined in the device tree. Signed-off-by: Marian Balakowicz <m8@semihalf.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-18[POWERPC] mpc5200: Add Promess Motion-PRO DTSMarian Balakowicz
Add device tree source file for Promess Motion-PRO board. Signed-off-by: Marian Balakowicz <m8@semihalf.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-18[POWERPC] mpc5200: add CM5200 DTSMarian Balakowicz
Add device tree source file for CM5200 board. Signed-off-by: Marian Balakowicz <m8@semihalf.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-18[POWERPC] mpc5200: Add TQM5200 DTSMarian Balakowicz
Add device tree source file for TQ Components TQM5200 board. Signed-off-by: Marian Balakowicz <m8@semihalf.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-17[POWERPC] Update .gitignore filesJochen Friedrich
Update .gitignore as needed by dtc addition. Signed-off-by: Jochen Friedrich <jochen@scram.de> Acked-by: David Gibson <david@gibson.dropbear.id.au> Signed-off-by: Paul Mackerras <paulus@samba.org>
2008-01-11Merge branch 'virtex-for-2.6.25' of ↵Josh Boyer
git://git.secretlab.ca/git/linux-2.6-virtex into for-2.6.25
2008-01-09[POWERPC] Xilinx: updated device tree compatibility to match uboot bsp ↵Stephen Neuendorffer
generator. Missed this one in the boot loader before. Signed-off-by: Stephen Neuendorffer <stephen.neuendorffer@xilinx.com> Signed-off-by: Grant Likely <grant.likely@secretlab.ca>
2008-01-08[POWERPC] 4xx: Add 405GPr and 405EP support in boot wrapperMatthias Fuchs
This patch adds support for 405GPr processors with optional new mode strapping. ibm405gp_fixup_clocks() can now be used for 405GP and 405GPr CPUs. This is in preparation of porting the cpci405 platform support from arch/ppc to arch/powerpc. This patch also adds ibm405ep_fixup_clocks() to support 405EP CPUs from the boot wrapper. Signed-off-by: Matthias Fuchs <matthias.fuchs@esd-electronics.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-24[POWERPC] 4xx: Minor coding style cleanups for 4xx bootwrapperJosh Boyer
Remove some unneeded braces and make a busy loop more obvious. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: Makalu dtsStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: Change Kilauea PCIe bus ranges in dts fileStefan Roese
Currently we have some limitations in the 4xx PCIe driver and can't support all possible PCIe busses. But the current limits in the dts file are quite low (only 16 busses per RC). This patch increases the number to 64 per RC. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: Add aliases node to 4xx dts filesStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: Add PCI entry to 440GRx Rainier DTS.Valentine Barshak
This adds PCI entry to PowerPC 440GRx Rainier DTS. Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: Rename CPU nodes to avoid dtc incompatibilityJosh Boyer
Recent DTC versions disallow certain special characters in full paths without being quoted with {}. That however breaks compatibility with older DTC versions. Work around this by renaming the CPU nodes for the 4xx files to a generic node name, and specify the processor type in the model property of the CPU node. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: Add Kilauea PCIe support to dts and KconfigStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: Change Kilauea dts to support new EMAC device tree propertiesStefan Roese
The recent changes from Benjamin Herrenschmidt to the ibm_newemac now make it possible to support other 4xx variants by just defining the correct properties in the device tree. In this case of the 405EX we need to define "has-mdio" in the RGMII node and "has-inverted-stacr-oc" and "has-new-stacr-staopc" in the EMAC node same as on the 440EPx. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: libfdt and pci fixes for RainierJosh Boyer
Update the Rainier wrapper for the libfdt merge and add the pci flags to the platform file. Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 44x: Sequoia and Rainier updates for 2.6.25Valentine Barshak
PowerPC 440Epx/GRx Sequoia/Rainier updates for 2.6.25 Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: Add PCI entry to 440EPx Sequoia DTS.Valentine Barshak
This adds PCI entry to PowerPC 440EPx Sequoia DTS. Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: 440GRx Rainier DTS.Valentine Barshak
PowerPC 440GRx Rainier DTS. Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: 440GRx Rainier bootwrapper.Valentine Barshak
Bootwrapper code for PowerPC 440GRx Rainier board. Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: 440EPx Sequoia USB OHCI DTS entryValentine Barshak
Add the 440EPx Sequoia USB OHCI device tree entry. Signed-off-by: Valentine Barshak <vbarshak@ru.mvista.com> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: Add 440SPe revA runtime detection to PCIeStefan Roese
This patch adds runtime detection of the 440SPe revision A chips. These chips are equipped with a slighly different PCIe core and need special/ different initialization. The compatible node is changed to "plb-pciex-440spe" ("A" and "B" dropped). This is needed for boards that can be equipped with both PPC revisions like the AMCC Yucca. Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: remove bogus "ranges" property in Bamboo EBC nodeBenjamin Herrenschmidt
This removes a bogus empty "ranges" property in the EBC device node of the Bamboo board device-tree. The "ranges" property should be created by the wrapper code when it is implemented. Until then, remove the empty property since it incorrectly implies that there is a 1:1 address mapping between the EBC and the OPB. This also fixes a warning from newer DTCs. Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
2007-12-23[POWERPC] 4xx: Base support for 440SPe "Katmai" eval boardBenjamin Herrenschmidt
This adds base support for the Katmai board, including PCI-X and PCI-Express (but no RTC, nvram, etc... yet). Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org> Acked-by: Stefan Roese <sr@denx.de> Signed-off-by: Josh Boyer <jwboyer@linux.vnet.ibm.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-03 17:05:47 +0000