| Age | Commit message (Collapse) | Author |
|---|
|
mvebu dt64 for 5.4 (part 1)
- Add mailbox support on Armada 37xx
- Add cpu clock node needed for CPU freq on Armada 7K/8K
- Enhance CP110 COMPHY support used by PCIe, USB3 and SATA
* tag 'mvebu-dt64-5.4-1' of git://git.infradead.org/linux-mvebu:
arm64: dts: marvell: Add cpu clock node on Armada 7K/8K
arm64: dts: marvell: Convert 7k/8k usb-phy properties to phy-supply
arm64: dts: marvell: Add 7k/8k PHYs in PCIe nodes
arm64: dts: marvell: Add 7k/8k PHYs in USB3 nodes
arm64: dts: marvell: Add 7k/8k per-port PHYs in SATA nodes
arm64: dts: marvell: Add CP110 COMPHY clocks
arm64: dts: marvell: armada-37xx: add mailbox node
Link: https://lore.kernel.org/r/875zmhzjml.fsf@FE-laptop
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX arm64 device tree update for 5.4:
- New board support: i.MX8MQ Nitrogen8m, Hummingboard Pulse,
PICO-PI-IMX8M, i.MX8QXP AI_ML, and LS1046A FRWY board.
- Add gpio-ranges for GPIO devices on i.MX8MQ and i.MX8MM.
- Update OPP table according to latest data sheet and add opp-suspend
to OPP table for i.MX8MQ and i.MX8MM.
- Add IDEL states for i.MX8MM SoC.
- Correct I2C clock divider for Layerscape SoCs.
- Add series alias and LPUART baud clock for i.MX8QXP SoC.
- Add MIPI D-PHY device for i.MX8MQ and enable it on imx8mq-librem5
board.
- Enable USB1 and Type-C support for i.MX8MM EVK board.
- Add Thermal Monitor Unit support for LS1028A SoC.
- Misc small update and correction on Layerscape and i.MX8 support.
* tag 'imx-dt64-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux: (41 commits)
arm64: dts: imx8mq: Add mux controller to iomuxc_gpr
arm64: dts: fsl: add support for Hummingboard Pulse
arm64: dts: ls1088a: update gpio compatible
arm64: dts: imx: Add i.mx8mq nitrogen8m basic dts support
arm64: dts: ls1088a-qds: Add the spi-flash nodes under the DSPI controller
arm64: dts: ls1088a: Add the DSPI controller node
arm64: dts: imx8mm: Enable cpu-idle driver
arm64: dts: ls1028a: Add esdhc node in dts
arm64: dts: ls1028a: Add properties node for Display output pixel clock
arm64: dts: lx2160a: Fix incorrect I2C clock divider
arm64: dts: ls1028a: Fix incorrect I2C clock divider
arm64: dts: ls1012a: Fix incorrect I2C clock divider
arm64: dts: ls1088a: Fix incorrect I2C clock divider
arm64: dts: ls1028a: fix gpio nodes
arm64: dts: ls1028a: Add Thermal Monitor Unit node
arm64: dts: imx8mq-evk: Unbypass audio_pll1
arm64: dts: imx8mm: Add opp-suspend property to OPP table
arm64: dts: imx8mq: Add opp-suspend property to OPP table
arm64: dts: ls1088a: Revise gpio registers to little-endian
arm64: dts: add the console node for DPAA2 platforms
...
Link: https://lore.kernel.org/r/20190825153237.28829-6-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux into arm/dt
i.MX device tree update with new clocks:
- A series from Anson Huang to add i.MX8MN SoC and DDR4 EVK board
device tree support.
- Add DSP device tree support for i.MX8QXP SoC.
* tag 'imx-dt-clkdep-5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/shawnguo/linux:
arm64: dts: imx8qxp: Add DSP DT node
arm64: dts: imx8mn: Add cpu-freq support
arm64: dts: imx8mn-ddr4-evk: Add rohm,bd71847 PMIC support
arm64: dts: imx8mn-ddr4-evk: Add i2c1 support
arm64: dts: freescale: Add i.MX8MN DDR4 EVK board support
arm64: dts: imx8mn: Add gpio-ranges property
arm64: dts: freescale: Add i.MX8MN dtsi support
clk: imx8: Add DSP related clocks
clk: imx: Add support for i.MX8MN clock driver
clk: imx: Add API for clk unregister when driver probe fail
clk: imx8mm: Make 1416X/1443X PLL macro definitions common for usage
dt-bindings: imx: Add clock binding doc for i.MX8MN
Link: https://lore.kernel.org/r/20190825153237.28829-4-shawnguo@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux into arm/dt
mt8183:
- fix pwrap interrupt number
- add i2c notes
dt-bindings:
- add compatible for mt6779
- add mt6779 uart and sysirq compatible
* tag 'v5.3-next-dts64' of git://git.kernel.org/pub/scm/linux/kernel/git/matthias.bgg/linux:
dt-bindings: irq: mtk, sysirq: add support for mt6779
dt-bindings: mtk-uart: add mt6779 uart bindings
dt-bindings: mediatek: add support for mt6779 reference board
arm64: dts: mt8183: add I2C nodes
arm64: dts: mt8183: fix pwrap gic number
Link: https://lore.kernel.org/r/def8fb77-fce4-097d-7ae2-8c4670bc09c1@gmail.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux into arm/dt
Allwinner DT changes for 5.4
Our usual pile of patches for the next release, which include mostly:
- More fixes thanks to the DT validation using the YAML bindings
- IR receiver support on the H6
- SPDIF support on the H6
- I2C Support on the H6
- CSI support on the A20
- RTC support on the H6
- New Boards: Lichee Zero Plus, Tanix TX6, A64-Olinuxino-eMMC
* tag 'sunxi-dt-for-5.4-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sunxi/linux: (40 commits)
arm64: dts: allwinner: orange-pi-3: Enable WiFi
ARM: dts: sunxi: Add missing watchdog clocks
ARM: dts: sunxi: Add missing watchdog interrupts
arm64: dts: allwinner: h6: Add support for RTC and fix the clock tree
ARM: dts: sun7i: Add CSI0 controller
arm64: dts: allwinner: a64: Add A64 OlinuXino board (with eMMC)
dt-bindings: arm: sunxi: Add compatible for A64 OlinuXino with eMMC
ARM: dts: v3s: Change the timers compatible
ARM: dts: h3: Change the timers compatible
ARM: dts: a83t: Change the timers compatible
ARM: dts: a23/a33: Change the timers compatible
ARM: dts: sun6i: Add missing timers interrupts
ARM: dts: sun5i: Add missing timers interrupts
ARM: dts: sun4i: Add missing timers interrupts
dt-bindings: mfd: Convert Allwinner GPADC bindings to a schema
arm64: dts: allwinner: h6: Introduce Tanix TX6 board
dt-bindings: arm: sunxi: Add compatible for Tanix TX6 board
arm64: allwinner: h6: add I2C nodes
dt-bindings: i2c: mv64xxx: Add compatible for the H6 i2c node.
ARM: dts: sunxi: Add mdio bus sub-node to GMAC
...
Link: https://lore.kernel.org/r/d97e6252-9dd7-4cf5-a3cf-56f78b0ca455.lettre@localhost
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel into arm/dt
Renesas ARM64 DT updates for v5.4 (take two)
- Sort nodes in various SoC and board DTSes,
- HDMI sound for HiHope RZ/G2M and R-Car M3-N Salvator-X(S) boards,
- Limit EtherAVB to 100Mbps on the Ebisu and Draak boards,
- Small fixes and improvements.
* tag 'renesas-arm64-dt-for-v5.4-tag2' of git://git.kernel.org/pub/scm/linux/kernel/git/geert/renesas-devel: (21 commits)
arm64: dts: renesas: Update 'vsps' properties for readability
arm64: dts: renesas: r8a77965-salvator-x(s): Enable HDMI sound
arm64: dts: renesas: r8a774c0: Fix register range of display node
arm64: dts: renesas: r8a77970: Sort nodes
arm64: dts: renesas: r8a7796: Sort nodes
arm64: dts: renesas: r8a774c0: Sort nodes
arm64: dts: renesas: r8a774c0: cat874: Sort nodes
arm64: dts: renesas: r8a774a1: Sort nodes
arm64: dts: renesas: r8a77980: Fix IPMMU-VC0 base address
arm64: dts: renesas: ebisu, draak: Limit EtherAVB to 100Mbps
arm64: dts: renesas: hihope-common: Add HDMI audio support
arm64: dts: renesas: r8a774c0: cat874: Add definition for 12V regulator
arm64: dts: renesas: r8a774c0: Point LVDS0 to its companion LVDS1
arm64: dts: renesas: r8a77995: Sort nodes
arm64: dts: renesas: r8a77995: draak: Sort nodes
arm64: dts: renesas: r8a77990: Sort nodes
arm64: dts: renesas: r8a77990: ebisu: Sort nodes
arm64: dts: renesas: r8a77980: v3hsk: Sort nodes
arm64: dts: renesas: r8a77980: condor: Sort nodes
arm64: dts: renesas: r8a77970: v3msk: Sort nodes
...
Link: https://lore.kernel.org/r/20190823123643.18799-4-geert+renesas@glider.be
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic into arm/dt
arm64: dts: Amlogic updates for v5.4
Highlights
- new SoCs (G12B family): S922X, A311D
- new SoCs (SM1 family): S905X3
- new board: SEI Robotics SEI610 (SM1/S905X3)
- new board: Khadas VIM3 (G12B/A311D)
- DVFS/CPUfreq support on G12[AB] family
* tag 'amlogic-dt64' of git://git.kernel.org/pub/scm/linux/kernel/git/khilman/linux-amlogic: (40 commits)
arm64: dts: add support for SM1 based SEI Robotics SEI610
dt-bindings: arm: amlogic: add SEI Robotics SEI610 bindings
dt-bindings: arm: amlogic: add SM1 bindings
arm64: dts: meson-g12b-odroid-n2: enable DVFS
arm64: dts: meson-g12b-khadas-vim3: add initial device-tree
dt-bindings: arm: amlogic: fix x96-max/sei510 section in amlogic.yaml
arm64: dts: amlogic: g12 CPU timers stop in suspend
arm64: dts: meson-g12b: support a311d and s922x cpu operating points
dt-bindings: arm: amlogic: add support for the Khadas VIM3
dt-bindings: arm: amlogic: add bindings for the Amlogic G12B based A311D SoC
dt-bindings: arm: amlogic: add bindings for G12B based S922X SoC
arm64: dts: meson: add video decoder entries
arm64: dts: meson-gx: add video decoder entry
dt-bindings: media: amlogic,vdec: add default compatible
arm64: dts: meson: add ethernet fifo sizes
arm64: dts: meson-g12b: add cpus OPP tables
arm64: dts: meson-g12a: enable DVFS on G12A boards
arm64: dts: meson-g12a: add cpus OPP table
arm64: dts: meson-g12-common: add pwm_a on GPIOE_2 pinmux
arm64: dts: move common G12A & G12B modes to meson-g12-common.dtsi
...
Link: https://lore.kernel.org/r/7hr25fbi4v.fsf@baylibre.com
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux into arm/dt
SoCFPGA DTS updates for v5.4
- Add reset properties for various peripherals
- QSPI OCP and DMA on Arria10
- DMA on Agilex/Stratix10
- Update NAND controller bindings to match driver update
- Add NAND controller to Stratix10
- VINING FPGA board fixups
- Update button mapping
- Adjust GMAC1 clock and TXD skew settings
- Add missing reset-names for dma controller
* tag 'socfpga_dts_updates_for_v5.4' of git://git.kernel.org/pub/scm/linux/kernel/git/dinguyen/linux:
ARM: dts: socfpga: add missing reset-names for dma
ARM: dts: socfpga: Adjust GMAC1 clock and TXD lines skew on VINING FPGA
ARM: dts: socfpga: Fix up button mapping on VINING FPGA
arm64: dts: stratix10: Add NAND device node
ARM: dts: socfpga: update to new Denali NAND binding
arm64: dts: agilex/stratix10: Add reset properties for DMA
ARM: dts: socfpga: add reset properties for DMA
ARM: dts: socfpga: add the QSPI OCP reset property on arria10
Link: https://lore.kernel.org/r/20190819141659.26414-1-dinguyen@kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip into arm/dt
PWM-Fan and nor-flash for the RockPro64, a better display mode for
the Kevin Chromebook and a new board the Leez P710 SBC.
* tag 'v5.4-rockchip-dts64-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mmind/linux-rockchip:
arm64: dts: rockchip: Add dts for Leez RK3399 P710 SBC
arm64: dts: rockchip: enable internal SPI flash for RockPro64.
arm64: dts: rockchip: Add PWM fan for RockPro64
arm64: dts: rockchip: Specify override mode for kevin panel
Link: https://lore.kernel.org/r/20190819141659.26414-1-dinguyen@kernel.org
Link: https://lore.kernel.org/r/2362486.gYoCZEsBuK@phil
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
Add cpu clock node on AP
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Update Aramda 7k/8k DTs to use the phy-supply property of the (recent)
generic PHY framework instead of the (legacy) usb-phy preperty. Both
enable the supply when the PHY is enabled.
The COMPHY nodes only provide SERDES lanes configuration. The power
supply that is represented by the phy-supply property is just a
regulator wired to the USB connector, hence the creation of connector
nodes as child of the COMPHY nodes and the supply attached to it.
Cc: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Fill-in the missing PCIe phys/phy-names DT properties of Armada 7k/8k
based boards.
The MacchiatoBin is a bit particular as the Armada8k-PCI IP supports
x4 link widths and in this case the PHY for each lane must be
referenced.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Fill-in the missing USB3 phys/phy-names DT properties of Armada 7k/8k
based boards. Only update nodes actually enabling USB3 in the default
(mainline) configuration. A few USB nodes are enabled but there is
only USB2 working on them.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Fill-in the missing SATA phys/phy-names DT properties of Armada 7k/8k
based boards.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
Declare the three clocks feeding the COMPHY block.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
This adds the rWTM BIU mailbox node for communication with the secure
processor. The driver already exists in
drivers/mailbox/armada-37xx-rwtm-mailbox.c.
Signed-off-by: Marek Behún <marek.behun@nic.cz>
Cc: Gregory Clement <gregory.clement@bootlin.com>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Signed-off-by: Gregory CLEMENT <gregory.clement@bootlin.com>
|
|
The only mux controls the MIPI DSI input selection.
Signed-off-by: Guido Günther <agx@sigxcpu.org>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The SolidRun Hummingboard Pulse carrier board carries the SolidRun
i.MX8MQ based SOM.
Notably missing is PCIe support that depends on analog PLLOUT clock.
Current imx clk driver does not support this clock.
Signed-off-by: Jon Nettleton <jon@solid-run.com>
Signed-off-by: Baruch Siach <baruch@tkos.co.il>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
add ls1088a gpio specify compatible.
Signed-off-by: Song Hui <hui.song_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add basic dts support for i.MX8MQ NITROGEN8M.
Signed-off-by: Gary Bisson <gary.bisson@boundarydevices.com>
Signed-off-by: Troy Kisky <troy.kisky@boundarydevices.com>
[Dafna: porting vendor's code to mainline]
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds the spi-flash nodes under the DSPI controller for
ls1088a-qds boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds the DSPI controller node for ls1088a boards.
Signed-off-by: Chuanhua Han <chuanhua.han@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called
bcm43356 and can be used with the brcmfmac driver. The module is powered by
the two always on regulators (not AXP805).
WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
configured so that it sets up an 1.8V input bias on this port. This is done
by the pio driver by reading the vcc-pg-supply voltage.
You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
configuration that can be found in the Xulongs's repository for H6:
https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256
Mainline brcmfmac driver expects the firmware and nvram at the following
paths relative to the firmware directory:
brcm/brcmfmac43456-sdio.bin
brcm/brcmfmac43456-sdio.txt
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The watchdog has a clock on all our SoCs, but it wasn't always listed.
Add it to the devicetree where it's missing.
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
This patch adds RTC node and fixes the clock properties and nodes
to reflect the real clock tree.
The device nodes for the internal oscillator and osc32k are removed,
as these clocks are now provided by the RTC device. Clock references
are fixed accordingly, too.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
A64 OLinuXino board from Olimex has three variants with onboard eMMC:
A64-OLinuXino-1Ge16GW, A64-OLinuXino-1Ge4GW and A64-OLinuXino-2Ge8G-IND. In
addition, there are two variants without eMMC. One without eMMC and one with SPI
flash. This suggests the need for separate device tree for the three eMMC
variants.
This patch has been tested on A64-OLinuXino-1Ge16GW with Linux 5.0 from Debain.
Basic benchmarks using Flexible IO Tester show reasonable performance from the
eMMC.
eMMC - Random Write: 21.3MiB/s
eMMC - Sequential Write: 68.2MiB/s
SD Card - Random Write: 1690KiB/s
SD Card - Sequential Write: 11.0MiB/s
Changes:
v3: Separate dts for eMMC variants
v2: Fix descriptions for VCC and VCCQ
Link: https://github.com/armbian/build/commit/174953de1eb09e6aa1ef7075066b573dba625398
Signed-off-by: Martin Ayotte <martinayotte@gmail.com>
[sunil@medhas.org Fix descriptions for VCC and VCCQ, separate dts for eMMC]
Signed-off-by: Sunil Mohan Adapa <sunil@medhas.org>
Tested-by: Sunil Mohan Adapa <sunil@medhas.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Tanix TX6 is an Allwinner H6 based TV box, which supports:
- Allwinner H6 Quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 4GiB DDR3 RAM (3GiB useable)
- 100Mbps EMAC via AC200 EPHY
- Cdtech 47822BS Wifi/BT
- 2x USB 2.0 Host and 1x USB 3.0 Host
- HDMI port
- IR receiver
- 64GiB eMMC
- 5V/2A DC power supply
Signed-off-by: Jernej Skrabec <jernej.skrabec@siol.net>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add device-tree nodes for i2c0 to i2c2, and also add relevant pinctrl
nodes.
Suggested-by: Icenowy Zheng <icenowy@aosc.io>
Signed-off-by: Bhushan Shah <bshah@kde.org>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Beelink GS1 has a DDC I2C bus voltage shifter. This is actually missing
and video is limited to 1024x768 due to missing EDID information.
Add the DDC regulator in the device-tree.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Beelink GS1 board has a SPDIF out connector, so enable it in
the device-tree and add a simple SPDIF soundcard.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
The Allwinner H6 has a SPDIF controller called OWA (One Wire Audio).
Only one pinmuxing is available so set it as default.
Signed-off-by: Clément Péron <peron.clem@gmail.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Orange Pi 3 has a DDC_CEC_EN signal connected to PH2, that enables the DDC
I2C bus voltage shifter. Before EDID can be read, we need to pull PH2 high.
This is realized by the ddc-en-gpios property.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
|
|
Add i2c nodes to mt8183 and mt8183-evb.
Signed-off-by: Qii Wang <qii.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
The correct gic number of pwrap is 185 instead of 209. This patch fixes
it to avoid triggering error interrupt.
Fixes: e526c9bc11f8 ("arm64: dts: Add Mediatek SoC MT8183 and evaluation board dts and Makefile")
Signed-off-by: Hsin-Hsiung Wang <hsin-hsiung.wang@mediatek.com>
Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com>
|
|
Update the 'vsps' property in the R-Car Gen3 SoC device tree files to
match what's in the documentation example.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Signed-off-by: Kuninori Morimoto <kuninori.morimoto.gx@renesas.com>
Tested-by: Jacopo Mondi <jacopo+renesas@jmondi.org> # Salvator-XS
[geert: Preserve sort order]
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Since the R8A774C0 SoC uses DU{0,1} only, the register block length
should be 0x40000.
Based on commit 06585ed38b6698bc ("arm64: dts: renesas: r8a77990: Fix
register range of display node") for R-Car E3.
Fixes: 8ed3a6b223159df3 ("arm64: dts: renesas: r8a774c0: Add display output support")
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Fabrizio Castro <fabrizio.castro@bp.renesas.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Sort nodes.
If node address is present
* Sort by node address, grouping all nodes with the same compat string
and sorting the group alphabetically.
Else
* Sort alphabetically
This should not have any run-time effect.
Signed-off-by: Yoshihiro Kaneko <ykaneko0929@gmail.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
|
|
Add support for the Amlogic SM1 Based SEI610 board.
The SM1 SoC is a derivative of the G12A SoC Family with :
- Cortex-A55 core instead of A53
- more power domains, including USB & PCIe
- a neural network co-processor (NNA)
- a CSI input and image processor
- some changes in the audio complex, thus not yet enabled
The SEI610 board is a derivative of the SEI510 board with :
- removed ADC based touch button, replaced with 3x GPIO buttons
- physical switch disabling on-board MICs
- USB-C port for USB 2.0 OTG
- On-board FTDI USB2SERIAL port for Linux console
Audio, Display and USB support will be added later when support of the
corresponding power domains will be added, for now they are kept disabled.
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
[khilman: fix minor typo regultor -> regulator]
Signed-off-by: Kevin Hilman <khilman@baylibre.com>
|
|
This includes DSP reserved memory, ADMA DSP device and DSP MU
communication channels description.
Signed-off-by: Daniel Baluta <daniel.baluta@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add A53 OPP table, cpu regulator and speed grading node to
support cpu-freq driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
On i.MX8MN DDR4 EVK board, there is a rohm,bd71847 PMIC
on i2c1 bus, enable it.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Enable i2c1 on i.MX8MN DDR4 EVK board.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
This patch adds basic i.MM8MN DDR4 EVK board support.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
Add "gpio-ranges" property to establish connections between GPIOs
and PINs on i.MX8MN pinctrl driver.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
|
The i.MX8M Nano Media Applications Processor is a new SoC of the i.MX8M
family, it is a 14nm FinFET product of the growing mScale family targeting
the consumer market. It is built in Samsung 14LPP to achieve both high
performance and low power consumption and relies on a powerful fully
coherent core complex based on a quad core ARM Cortex-A53 cluster,
Cortex-M7 low-power coprocessor and graphics accelerator.
This patch adds the basic dtsi support for i.MX8MN.
Signed-off-by: Anson Huang <Anson.Huang@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
