| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM device tree updates from Arnd Bergmann:
"Across all platforms, there is a continued move towards DT schema for
validating the dts files. As a result there are bug fixes for mistakes
that are found using these schema, in addition to warnings from the
dtc compiler.
As usual, many changes are for adding support for additional on-chip
and on-board components in the machines we already support.
The newly supported SoCs for this release are:
- MStar Infinity2M, a low-end IP camera chip based on a dual-core
Cortex-A7, otherwise similar to the Infinity chip we already
support. This is also known as the SigmaStar SSD202D, and we add
support for the Honestar ssd201htv2 development kit.
- Nuvoton NPCM730, a Cortex-A9 based Baseboard Management Controller
(BMC), in the same family as the NPCM750. This gets used in the
Ampere Altra based "Fii Kudo" server and the Quanta GSJ, both of
which are added as well.
- Broadcom BCM4908, a 64-bit home router chip based on Broadcom's own
Brahma-B53 CPU. Support is also added for the Asus ROG Rapture
GT-AC5300 high-end WiFi router based on this chip.
- Mediatek MT8192 is a new SoC based on eight Cortex-A76/A55 cores,
meant for faster Chromebooks and tablets. It gets added along with
its reference design.
- Mediatek MT6779 (Helio P90) is a high-end phone chip from last
year's generation, also added along with its reference board. This
one is still based on Cortex-A75/A55.
- Mediatek MT8167 is a version of the already supported MT8516 chip,
both based on Cortex-A35. It gets added along with the "Pumpkin"
single board computer, but is likely to also make its way into
low-end tablets in the future.
For the already supported chips, there are a number of new boards.
Interestingly there are more 32-bit machines added this time than
64-bit. Here is a brief list of the new boards:
- Three new Mikrotik router variants based on Marvell Prestera
98DX3236, a close relative of the more common Armada XP
- A reference board for the Marvell Armada 382
- Three new servers using ASpeed baseboard management controllers,
the actual machines being from Bytedance, Facebook and IBM, and one
machine using the Nuvoton NPCM750 BMC.
- The Galaxy Note 10.1 (P4) tablet, using an Exynos 4412.
- The usual set of 32-bit i.MX industrial/embedded hardware:
* Protonic WD3 (tractor e-cockpit)
* Kamstrup OMNIA Flex Concentrator (smart grid platform)
* Van der Laan LANMCU (food storage)
* Altesco I6P (vehicle inspection stations)
* PHYTEC phyBOARD-Segin/phyCORE-i.MX6UL baseboard
- DH electronics STM32MP157C DHCOM, a PicoITX carrier board for the
aleady supported DHCOM module
- Three new Allwinner SoC based single-board computers:
* NanoPi R1 (H3 based)
* FriendlyArm ZeroPi (H3 based)
* Elimo Initium SBC (S3 based)
- Ouya Game Console based on Nvidia Tegra 3
- Version 5 of the already supported Zynq Z-Turn MYIR Board
- LX2162AQDS, a reference platform for NXP Layerscape LX2162A, which
is a repackaged 16-core LX2160A
- A series of Kontron i.MX8M Mini baseboard/SoM versions
- Espressobin Ultra, a new variant of the popular Armada 3700 based
board,
- IEI Puzzle-M801, a rackmount network appliance based on Marvell
Armada 8040
- Microsoft Lumia 950 XL, a phone
- HDK855 and HDK865 Hardware development kits for Qualcomm sm8250 and
sm8150, respectively
- Three new board variants of the "Trogdor" Chromebook (sc7180)
- New board variants of the Renesas based "Kingfisher" and "HiHope"
reference boards
- Kobol Helios64, an open source NAS appliance based on Rockchips
RK3399
- Engicam PX30.Core, a SoM based on Rockchip PX30, along with a few
carrier boards"
* tag 'arm-soc-dt-5.11' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (679 commits)
arm64: dts: sparx5: Add SGPIO devices
arm64: dts: sparx5: Add reset support
dt-bindings: gpio: Add a binding header for the MSC313 GPIO driver
ARM: mstar: SMP support
ARM: mstar: Wire up smpctrl for SSD201/SSD202D
ARM: mstar: Add smp ctrl registers to infinity2m dtsi
ARM: mstar: Add dts for Honestar ssd201htv2
ARM: mstar: Add chip level dtsi for SSD202D
ARM: mstar: Add common dtsi for SSD201/SSD202D
ARM: mstar: Add infinity2m support
dt-bindings: mstar: Add Honestar SSD201_HT_V2 to mstar boards
dt-bindings: vendor-prefixes: Add honestar vendor prefix
dt-bindings: mstar: Add binding details for mstar,smpctrl
ARM: mstar: Fill in GPIO controller properties for infinity
ARM: mstar: Add gpio controller to MStar base dtsi
ARM: zynq: Fix incorrect reference to XM013 instead of XM011
ARM: zynq: Convert at25 binding to new description on zc770-xm013
ARM: zynq: Fix OCM mapping to be aligned with binding on zc702
ARM: zynq: Fix leds subnode name for zc702/zybo-z7
ARM: zynq: Rename bus to be align with simple-bus yaml
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- support for inhibiting input devices at request from userspace. If a
device implements open/close methods, it can also put device into low
power state. This is needed, for example, to disable keyboard and
touchpad on convertibles when they are transitioned into tablet mode
- now that ordinary input devices can be configured for polling mode,
dedicated input polling device implementation has been removed
- GTCO tablet driver has been removed, as it used problematic custom
HID parser, devices are EOL, and there is no interest from the
manufacturer
- a new driver for Dialog DA7280 haptic chips has been introduced
- a new driver for power button on Dell Wyse 3020
- support for eKTF2132 in ektf2127 driver
- support for SC2721 and SC2730 in sc27xx-vibra driver
- enhancements for Atmel touchscreens, AD7846 touchscreens, Elan
touchpads, ADP5589, ST1232 touchscreen, TM2 touchkey drivers
- fixes and cleanups to allow clean builds with W=1
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (86 commits)
Input: da7280 - fix spelling mistake "sequemce" -> "sequence"
Input: cyapa_gen6 - fix out-of-bounds stack access
Input: sc27xx - add support for sc2730 and sc2721
dt-bindings: input: Add compatible string for SC2721 and SC2730
dt-bindings: input: Convert sc27xx-vibra.txt to json-schema
Input: stmpe - add axis inversion and swapping capability
Input: adp5589-keys - do not explicitly control IRQ for wakeup
Input: adp5589-keys - do not unconditionally configure as wakeup source
Input: ipx4xx-beeper - convert comma to semicolon
Input: parkbd - convert comma to semicolon
Input: new da7280 haptic driver
dt-bindings: input: Add document bindings for DA7280
MAINTAINERS: da7280 updates to the Dialog Semiconductor search terms
Input: elantech - fix protocol errors for some trackpoints in SMBus mode
Input: elan_i2c - add new trackpoint report type 0x5F
Input: elants - document some registers and values
Input: atmel_mxt_ts - simplify the return expression of mxt_send_bootloader_cmd()
Input: imx_keypad - add COMPILE_TEST support
Input: applespi - use new structure for SPI transfer delays
Input: synaptics-rmi4 - use new structure for SPI transfer delays
...
|
|
This driver uses GPIO descriptors to drive the touchscreen RESET line. In
the existing device trees this has in conflict with intution been flagged
as GPIO_ACTIVE_HIGH and the driver then applies the reverse action by
driving the line low (setting to 0) to enter reset state and driving the
line high (setting to 1) to get out of reset state.
The correct way to handle active low GPIO lines is to provide the
GPIO_ACTIVE_LOW in the device tree (thus properly describing the hardware)
and letting the GPIO framework invert the assertion (driving high) to a
low level and vice versa.
This is considered a bug since the device trees are incorrectly
mis-specifying the line as active high.
Fix the driver and all device trees specifying a reset line.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Philippe Schenker <philippe.schenker@toradex.com>
Acked-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201104153032.1387747-1-linus.walleij@linaro.org
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
|
|
This property is only useful if a node has children as it allows them
to then use io-channel properties in the parent. Here there are no
children.
This is harmless, but we are planning to shortly drop this property
as it is rarely used correctly and there is little reason it would
ever be needed as we can just provide the io-channels property to
any child nodes that need it.
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Link: https://lore.kernel.org/r/20201115192951.1073632-8-jic23@kernel.org
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The Devicetree specification expects device node names to have a generic
name, representing the class of a device. Also the convention for node
names is to use hyphens, not underscores.
No functional changes.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Link: https://lore.kernel.org/r/20201027170947.132725-10-krzk@kernel.org
|
|
The device tree schema expects SPI controller to be named "spi",
otherwise dtbs_check complain with a warning like:
spi-gpio-0: $nodename:0: 'spi-gpio-0' does not match '^spi(@.*|-[0-9a-f])*$'
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-25-krzk@kernel.org
|
|
The S3C RTC requires 32768 Hz clock as input which is provided by PMIC.
However there is no such clock provider but rather a regulator driver
which registers the clock as a regulator. This is an old driver which
will not be updated so add a workaround - a fixed-clock to fill missing
clock phandle reference in S3C RTC.
This fixes dtbs_check warnings:
rtc@e2800000: clocks: [[2, 145]] is too short
rtc@e2800000: clock-names: ['rtc'] is too short
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Tested-by: Jonathan Bakker <xc-racer2@live.ca>
Link: https://lore.kernel.org/r/20200907161141.31034-12-krzk@kernel.org
|
|
Fix typo in pinctrl property of "vibrator-en" fixed regulator in Aries
family of boards. The error caused lack of pin configuration for the
GPIO used in vibrator.
Fixes: 04568cb58a43 ("ARM: dts: s5pv210: Disable pull for vibrator enable GPIO on Aries boards")
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Cc: <stable@vger.kernel.org>
Link: https://lore.kernel.org/r/20200907161141.31034-5-krzk@kernel.org
|
|
Both the Galaxy S and the Fascinate4G have a WM8994 codec, but they
differ slightly in their jack detection and micbias configuration.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
There are several issues with the bluetooth node - the wrong
compatible was used (because the bcm4329 compatible didn't exist
when the node was added), the max rate was incorrect (due to
limitations in the samsung TTY driver which have now been fixed),
the clocks were not assigned properly so some rates didn't work,
and the some pinctrl settings weren't explicitly set. Fix all
of the above issues.
While we're at it, update from the deprecated host-wakeup-gpios
property to the host-wake interrupt.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Aries boards have a BMA023 accelerometer attached over i2c-gpio.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Aries boards have a GP2A light/proximity sensor attached over i2c-gpio.
As the chip outputs a current and the board has no current ADC, a
current shunt resistor and a voltage ADC are used.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Correct the fuelgauge definition because only the fuelgauge on
fascinate4g has interrupt support (and even then it was wrong).
Also, assign the GPIO pinctrl so the interrupt is properly configured
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Make sure that the GPIOs are configured correctly
for the interrupt (otherwise it won't fire) and disable the
pulls on the DVS GPIOs which are outputs.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The SHDCI controller on Aries devices is a little bit peculiar about
the clocks and with a slightly off clock can run into errors such as:
mmc2: ADMA error: 0x02000000
mmc2: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc2: sdhci: Sys addr: 0x347e4cc4 | Version: 0x00002401
mmc2: sdhci: Blk size: 0x00007004 | Blk cnt: 0x0000fffc
mmc2: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013
mmc2: sdhci: Present: 0x01fa0000 | Host ctl: 0x00000012
mmc2: sdhci: Power: 0x00000000 | Blk gap: 0x00000000
mmc2: sdhci: Wake-up: 0x00000000 | Clock: 0x0000010f
mmc2: sdhci: Timeout: 0x0000000a | Int stat: 0x00000003
mmc2: sdhci: Int enab: 0x03ff004b | Sig enab: 0x03ff004b
mmc2: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00000001
mmc2: sdhci: Caps: 0x05e80080 | Caps_1: 0x00000000
mmc2: sdhci: Cmd: 0x0000163a | Max curr: 0x00000000
mmc2: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x00000000
mmc2: sdhci: Resp[2]: 0x00000000 | Resp[3]: 0x00000000
mmc2: sdhci: Host ctl2: 0x00000000
mmc2: sdhci: ADMA Err: 0x00000000 | ADMA Ptr: 0x349a3208
mmc2: sdhci: ============================================
mmc2: sdhci: 349a3200: DMA 0x347e4cc0, LEN 0x0004, Attr=0x23
Specifically assign the MMC sclks to be parented from MPLL with specific
rates that match the vendor kernel.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
On Aries boards, the ADC is used for things such as jack detection
and battery temperature monitoring. It is supplied by LDO4 of max8998,
so only enable that regulator when we are actually using the ADC.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The enable GPIO for the fixed vibrator regulator shouldn't be
pulled in one direction or the other.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Add support for the Silicon Labs si4709 FM radio, which can be found
on Galaxy S GT-i9000 (but not on most of other Aries variants).
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The remaining i2c-gpio adapters that are common to all Aries boards
have devices without mainline bindings attachted to them. Add them
here for documentation.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Aries boards have an s6e63m0 AMOLED panel connected over i2c-spi.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Aries boards have soft touchkeys, manufactured by Cypress,
attached over i2c-gpio.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The Fairchild FSA9480 is a USB mux connected over i2c-gpio.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
Aries boards have a Wolfson WM8994 sound card attached over gpio-i2c.
There is currently no ASoC Machine Driver.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
The bitbanged GPIO I2C adapters have external pull-ups attached
so the internal pulls should be disabled for lower power usage.
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
SDHCI1 is connected to a BCM4329 WiFi/BT chip which requires
power to be kept over suspend. As the surrounding hardware supports
this, mark it as such. This fixes WiFi after a suspend/resume cycle.
Fixes: 170642468a51 ("ARM: dts: s5pv210: Add initial DTS for Samsung Aries based phones")
Cc: <stable@vger.kernel.org>
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
This commit enables following devices present on Aries based phones:
- pwm-vibrator attached to PWM 1
- poweroff support
- Atmel maXTouch touchscreen, connected to I2C-2
- Broadcom BCM4329 Bluetooth over UART-0
Signed-off-by: Jonathan Bakker <xc-racer2@live.ca>
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
THis commit adds memory reservation required by MFC (Multi Format Codec)
to run. On S5PV210 both regions needs to be on separate memory banks.
Size of both regions is taken from vendor Linux kernel sources.
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
This DTS file have initial support Samsung Aries based phones.
Initial version have support for:
- sdcard
- internal memory (present only on non 4g variant)
- max8998 pmic and rtc
- max17040 fuel gauge
- gpio keys
- fimd (no panel driver yet)
- usb (peripherial mode)
- wifi
Signed-off-by: Paweł Chmiel <pawel.mikolaj.chmiel@gmail.com>
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
