| Age | Commit message (Collapse) | Author |
|---|
|
This adds new dt entries qcom,coexist-support and qcom,coexist-gpio-pin
which will be used by ath10k driver to identify coex support
of a hardware and notify wifi firmware the gpio pin number.
This pin number information is needed for the hardware QCA4019.
Signed-off-by: Tamizh Chelvam <tamizhr@codeaurora.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc
Pull ARM SoC-related driver updates from Olof Johansson:
"Various driver updates for platforms:
- Nvidia: Fuse support for Tegra194, continued memory controller
pieces for Tegra30
- NXP/FSL: Refactorings of QuickEngine drivers to support
ARM/ARM64/PPC
- NXP/FSL: i.MX8MP SoC driver pieces
- TI Keystone: ring accelerator driver
- Qualcomm: SCM driver cleanup/refactoring + support for new SoCs.
- Xilinx ZynqMP: feature checking interface for firmware. Mailbox
communication for power management
- Overall support patch set for cpuidle on more complex hierarchies
(PSCI-based)
and misc cleanups, refactorings of Marvell, TI, other platforms"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (166 commits)
drivers: soc: xilinx: Use mailbox IPI callback
dt-bindings: power: reset: xilinx: Add bindings for ipi mailbox
drivers: soc: ti: knav_qmss_queue: Pass lockdep expression to RCU lists
MAINTAINERS: Add brcmstb PCIe controller entry
soc/tegra: fuse: Unmap registers once they are not needed anymore
soc/tegra: fuse: Correct straps' address for older Tegra124 device trees
soc/tegra: fuse: Warn if straps are not ready
soc/tegra: fuse: Cache values of straps and Chip ID registers
memory: tegra30-emc: Correct error message for timed out auto calibration
memory: tegra30-emc: Firm up hardware programming sequence
memory: tegra30-emc: Firm up suspend/resume sequence
soc/tegra: regulators: Do nothing if voltage is unchanged
memory: tegra: Correct reset value of xusb_hostr
soc/tegra: fuse: Add APB DMA dependency for Tegra20
bus: tegra-aconnect: Remove PM_CLK dependency
dt-bindings: mediatek: add MT6765 power dt-bindings
soc: mediatek: cmdq: delete not used define
memory: tegra: Add support for the Tegra194 memory controller
memory: tegra: Only include support for enabled SoCs
memory: tegra: Support DVFS on Tegra186 and later
...
|
|
Pull ARM Device-tree updates from Olof Johansson:
"New SoCs:
- Atmel/Microchip SAM9X60 (ARM926 SoC)
- OMAP 37xx gets split into AM3703/AM3715/DM3725, who are all
variants of it with different GPU/media IP configurations.
- ST stm32mp15 SoCs (1-2 Cortex-A7, CAN, GPU depending on SKU)
- ST Ericsson ab8505 (variant of ab8500) and db8520 (variant of
db8500)
- Unisoc SC9863A SoC (8x Cortex-A55 mobile chipset w/ GPU, modem)
- Qualcomm SC7180 (8-core 64bit SoC, unnamed CPU class)
New boards:
- Allwinner:
+ Emlid Neutis SoM (H3 variant)
+ Libre Computer ALL-H3-IT
+ PineH64 Model B
- Amlogic:
+ Libretech Amlogic GX PC (s905d and s912-based variants)
- Atmel/Microchip:
+ Kizboxmini, sam9x60 EK, sama5d27 Wireless SOM (wlsom1)
- Marvell:
+ Armada 385-based SolidRun Clearfog GTR
- NXP:
+ Gateworks GW59xx boards based on i.MX6/6Q/6QDL
+ Tolino Shine 3 eBook reader (i.MX6sl)
+ Embedded Artists COM (i.MX7ULP)
+ SolidRun CLearfog CX/ITX and HoneyComb (LX2160A-based systems)
+ Google Coral Edge TPU (i.MX8MQ)
- Rockchip:
+ Radxa Dalang Carrier (supports rk3288 and rk3399 SOMs)
+ Radxa Rock Pi N10 (RK3399Pro-based)
+ VMARC RK3399Pro SOM
- ST:
+ Reference boards for stm32mp15
- ST Ericsson:
+ Samsung Galaxy S III mini (GT-I8190)
+ HREF520 reference board for DB8520
- TI OMAP:
+ Gen1 Amazon Echo (OMAP3630-based)
- Qualcomm:
+ Inforce 6640 Single Board Computer (msm8996-based)
+ SC7180 IDP (SC7180-based)"
* tag 'armsoc-dt' of git://git.kernel.org/pub/scm/linux/kernel/git/soc/soc: (623 commits)
dt-bindings: fix compilation error of the example in marvell,mmp3-hsic-phy.yaml
arm64: dts: ti: k3-am654-base-board: Add CSI2 OV5640 camera
arm64: dts: ti: k3-am65-main Add CAL node
arm64: dts: ti: k3-j721e-main: Add McASP nodes
arm64: dts: ti: k3-am654-main: Add McASP nodes
arm64: dts: ti: k3-j721e: DMA support
arm64: dts: ti: k3-j721e-main: Move secure proxy and smmu under main_navss
arm64: dts: ti: k3-j721e-main: Correct main NAVSS representation
arm64: dts: ti: k3-j721e: Correct the address for MAIN NAVSS
arm64: dts: ti: k3-am65: DMA support
arm64: dts: ti: k3-am65-main: Move secure proxy under cbass_main_navss
arm64: dts: ti: k3-am65-main: Correct main NAVSS representation
ARM: dts: aspeed: rainier: Add UCD90320 power sequencer
ARM: dts: aspeed: rainier: Switch PSUs to unknown version
arm64: dts: rockchip: Kill off "simple-panel" compatibles
ARM: dts: rockchip: Kill off "simple-panel" compatibles
arm64: dts: rockchip: rename dwmmc node names to mmc
ARM: dts: rockchip: rename dwmmc node names to mmc
arm64: dts: exynos: Rename Samsung and Exynos to lowercase
arm64: dts: uniphier: add reset-names to NAND controller node
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c updates from Wolfram Sang:
"i2c core:
- huge improvements and refactorizations of the Linux I2C
documentation (lots of thanks to Luca for doing it and Jean for the
careful review)
- subsystem wide API conversion to i2c_new_client_device()
- remove obsolete parport-light driver
- smaller core updates (removal of 'extern', enabling more compile
testing, use more helper macros)
- and quite a bunch of driver updates (new IDs, simplifications,
better PM, support of atomic transfers and other improvements)
i2c-mux:
- The main feature is the idle-state rework of the pca954x driver
from Biwen Li
at24 driver:
- minor maintenance: update the license tag, sort headers
- move support for the write-protect pin into nvmem core
- add a reference to the new wp-gpios property in nvmem to at25
bindings
- add support for regulator and pm_runtime control"
* 'i2c/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux: (91 commits)
i2c: cros-ec-tunnel: Fix ACPI identifier
i2c: cros-ec-tunnel: Fix slave device enumeration
i2c: stm32f7: add PM_SLEEP suspend/resume support
i2c: cadence: Fix wording in i2c-cadence driver
i2c: cadence: Fix power management order of operations
i2c: cadence: Fix error printing in case of defer
i2c: cadence: Handle transfer_size rollover
i2c: i801: Add support for Intel Comet Lake PCH-V
docs: i2c: writing-clients: properly name the stop condition
docs: i2c: i2c-protocol: use same wording as smbus-protocol
docs: i2c: rename sections so the overall picture is clearer
docs: i2c: old-module-parameters: use monospace instead of ""
docs: i2c: old-module-parameters: clarify this is for obsolete kernels
docs: i2c: old-module-parameters: fix internal hyperlink
docs: i2c: instantiating-devices: use monospace for sysfs attributes
docs: i2c: instantiating-devices: rearrange static instatiation
docs: i2c: instantiating-devices: fix internal hyperlink
docs: i2c: smbus-protocol: improve I2C Block transactions description
docs: i2c: smbus-protocol: fix punctuation
docs: i2c: smbus-protocol: fix typo
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk fixes from Stephen Boyd:
"A collection of fixes:
- Make of_clk.h self contained
- Fix new qcom DT bindings that just merged to match the DTS files
- Fix qcom clk driver to properly detect DFS clk frequencies
- Fix the ls1028a driver to not deref a pointer before assigning it"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux:
of: clk: Make <linux/of_clk.h> self-contained
clk: qcom: Use ARRAY_SIZE in videocc-sc7180 for parent clocks
clk: qcom: Get rid of the test clock for videocc-sc7180
dt-bindings: clock: Cleanup qcom,videocc bindings for sdm845/sc7180
clk: qcom: Use ARRAY_SIZE in gpucc-sc7180 for parent clocks
clk: qcom: Get rid of the test clock for gpucc-sc7180
dt-bindings: clock: Fix qcom,gpucc bindings for sdm845/sc7180/msm8998
clk: qcom: Use ARRAY_SIZE in dispcc-sc7180 for parent clocks
clk: qcom: Get rid of the test clock for dispcc-sc7180
clk: qcom: Get rid of fallback global names for dispcc-sc7180
dt-bindings: clock: Fix qcom,dispcc bindings for sdm845/sc7180
clk: qcom: rcg2: Don't crash if our parent can't be found; return an error
clk: ls1028a: fix a dereference of pointer 'parent' before a null check
dt-bindings: clk: qcom: Fix self-validation, split, and clean cruft
clk: qcom: Don't overwrite 'cfg' in clk_rcg2_dfs_populate_freq()
|
|
git://www.linux-watchdog.org/linux-watchdog
Pull watchdog updates from Wim Van Sebroeck:
- add IT8786 chipset ID
- addition of sam9x60 compatible watchdog
- da9062 improvements
- fix UAF in reboot notifier handling in watchdog core code
- other fixes and small improvements
* tag 'linux-watchdog-5.6-rc1' of git://www.linux-watchdog.org/linux-watchdog:
watchdog: da9062: make restart handler atomic safe
watchdog: mtk_wdt: mt2712: Add reset controller
watchdog: mtk_wdt: mt8183: Add reset controller
dt-bindings: mediatek: mt2712: Add #reset-cells
dt-bindings: mediatek: mt8183: Add #reset-cells
dt-bindings: watchdog: da9062: add suspend disable option
watchdog: it87_wdt: add IT8786 ID
watchdog: dw_wdt: ping watchdog to reset countdown before start
watchdog: fix UAF in reboot notifier handling in watchdog core code
watchdog: cadence: Skip printing pointer value
watchdog: qcom: Use platform_get_irq_optional() for bark irq
watchdog: da9062: add power management ops
watchdog: make DesignWare watchdog allow users to set bigger timeout value
drivers: watchdog: stm32_iwdg: set WDOG_HW_RUNNING at probe
watchdog: sama5d4_wdt: addition of sam9x60 compatible watchdog
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm
Pull pwm updates from Thierry Reding:
"Mostly cleanups and minor improvements with some new chip support for
some drivers"
* tag 'pwm/for-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thierry.reding/linux-pwm: (37 commits)
pwm: Remove set but not set variable 'pwm'
pwm: sun4i: Initialize variables before use
pwm: stm32: Remove automatic output enable
pwm: sun4i: Narrow scope of local variable
pwm: bcm2835: Allow building for ARCH_BRCMSTB
pwm: imx27: Eliminate error message for defer probe
pwm: sun4i: Fix inconsistent IS_ERR and PTR_ERR
pwm: sun4i: Move pwm_calculate() out of spin_lock()
pwm: omap-dmtimer: Allow compiling with COMPILE_TEST
pwm: omap-dmtimer: put_device() after of_find_device_by_node()
pwm: omap-dmtimer: Simplify error handling
pwm: omap-dmtimer: Remove PWM chip in .remove before making it unfunctional
pwm: Implement tracing for .get_state() and .apply_state()
pwm: rcar: Document inability to set duty_cycle = 0
pwm: rcar: Drop useless call to pwm_get_state()
pwm: Fix minor Kconfig whitespace issues
pwm: atmel: Implement .get_state()
pwm: atmel: Use register accessors for channels
pwm: atmel: Document known weaknesses of both hardware and software
pwm: atmel: Replace loop in prescale calculation by ad-hoc calculation
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull iommu updates from Joerg Roedel:
- Allow compiling the ARM-SMMU drivers as modules.
- Fixes and cleanups for the ARM-SMMU drivers and io-pgtable code
collected by Will Deacon. The merge-commit (6855d1ba7537) has all the
details.
- Cleanup of the iommu_put_resv_regions() call-backs in various
drivers.
- AMD IOMMU driver cleanups.
- Update for the x2APIC support in the AMD IOMMU driver.
- Preparation patches for Intel VT-d nested mode support.
- RMRR and identity domain handling fixes for the Intel VT-d driver.
- More small fixes and cleanups.
* tag 'iommu-updates-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (87 commits)
iommu/amd: Remove the unnecessary assignment
iommu/vt-d: Remove unnecessary WARN_ON_ONCE()
iommu/vt-d: Unnecessary to handle default identity domain
iommu/vt-d: Allow devices with RMRRs to use identity domain
iommu/vt-d: Add RMRR base and end addresses sanity check
iommu/vt-d: Mark firmware tainted if RMRR fails sanity check
iommu/amd: Remove unused struct member
iommu/amd: Replace two consecutive readl calls with one readq
iommu/vt-d: Don't reject Host Bridge due to scope mismatch
PCI/ATS: Add PASID stubs
iommu/arm-smmu-v3: Return -EBUSY when trying to re-add a device
iommu/arm-smmu-v3: Improve add_device() error handling
iommu/arm-smmu-v3: Use WRITE_ONCE() when changing validity of an STE
iommu/arm-smmu-v3: Add second level of context descriptor table
iommu/arm-smmu-v3: Prepare for handling arm_smmu_write_ctx_desc() failure
iommu/arm-smmu-v3: Propagate ssid_bits
iommu/arm-smmu-v3: Add support for Substream IDs
iommu/arm-smmu-v3: Add context descriptor tables allocators
iommu/arm-smmu-v3: Prepare arm_smmu_s1_cfg for SSID support
ACPI/IORT: Parse SSID property of named component node
...
|
|
The $id path checks were inadequately checking the path part of the $id
value. With the check fixed, there's a number of errors that need to be
fixed. Most of the errors are including 'bindings/' in the path which
should not be as that is considered the root.
Cc: Andy Gross <agross@kernel.org>
Cc: Bjorn Andersson <bjorn.andersson@linaro.org>
Cc: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Cc: Michael Turquette <mturquette@baylibre.com>
Cc: Shawn Guo <shawnguo@kernel.org>
Cc: Sascha Hauer <s.hauer@pengutronix.de>
Cc: Pengutronix Kernel Team <kernel@pengutronix.de>
Cc: Fabio Estevam <festevam@gmail.com>
Cc: NXP Linux Team <linux-imx@nxp.com>
Cc: Maxime Coquelin <mcoquelin.stm32@gmail.com>
Cc: Alexandre Torgue <alexandre.torgue@st.com>
Cc: "Nuno Sá" <nuno.sa@analog.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: Stefan Popa <stefan.popa@analog.com>
Cc: Jonathan Cameron <jic23@kernel.org>
Cc: Hartmut Knaack <knaack.h@gmx.de>
Cc: Lars-Peter Clausen <lars@metafoo.de>
Cc: Peter Meerwald-Stadler <pmeerw@pmeerw.net>
Cc: Marcus Folkesson <marcus.folkesson@gmail.com>
Cc: Kent Gustavsson <kent@minoris.se>
Cc: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Cc: linux-clk@vger.kernel.org
Cc: linux-iio@vger.kernel.org
Cc: linux-input@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Reviewed-by: Stephen Boyd <sboyd@kernel.org>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
Remove <dt-bindings/clock/intel,lgm-clk.h> dependency as
it is not present in the mainline tree. Use numeric value
instead of LGM_GCLK_PCIE10 macro.
Signed-off-by: Dilip Kota <eswara.kota@linux.intel.com>
[robh: Also drop interrupt-parent from example]
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
DT labels can't have '-' in them causing a compile failure in the example.
Fixing that leads to more warnings:
Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.example.dts:23.13-33: Warning (reg_format): /example-0/chiptop@e0200000/emmc-phy@a8:reg: property has invalid length (8 bytes) (#address-cells == 2, #size-cells == 1)
Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.example.dt.yaml: Warning (pci_device_bus_num): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.example.dt.yaml: Warning (i2c_bus_reg): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.example.dt.yaml: Warning (spi_bus_reg): Failed prerequisite 'reg_format'
Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.example.dts:21.33-26.13: Warning (avoid_default_addr_size): /example-0/chiptop@e0200000/emmc-phy@a8: Relying on default #address-cells value
Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.example.dts:21.33-26.13: Warning (avoid_default_addr_size): /example-0/chiptop@e0200000/emmc-phy@a8: Relying on default #size-cells value
Fixes: 5bc999108025 ("dt-bindings: phy: intel-emmc-phy: Add YAML schema for LGM eMMC PHY")
Cc: Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
Cc: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Cc: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"A pretty small batch for us, and apologies for it being a bit late, I
wanted to sneak Christophe's user_access_begin() series in.
Summary:
- Implement user_access_begin() and friends for our platforms that
support controlling kernel access to userspace.
- Enable CONFIG_VMAP_STACK on 32-bit Book3S and 8xx.
- Some tweaks to our pseries IOMMU code to allow SVMs ("secure"
virtual machines) to use the IOMMU.
- Add support for CLOCK_{REALTIME/MONOTONIC}_COARSE to the 32-bit
VDSO, and some other improvements.
- A series to use the PCI hotplug framework to control opencapi
card's so that they can be reset and re-read after flashing a new
FPGA image.
As well as other minor fixes and improvements as usual.
Thanks to: Alastair D'Silva, Alexandre Ghiti, Alexey Kardashevskiy,
Andrew Donnellan, Aneesh Kumar K.V, Anju T Sudhakar, Bai Yingjie, Chen
Zhou, Christophe Leroy, Frederic Barrat, Greg Kurz, Jason A.
Donenfeld, Joel Stanley, Jordan Niethe, Julia Lawall, Krzysztof
Kozlowski, Laurent Dufour, Laurentiu Tudor, Linus Walleij, Michael
Bringmann, Nathan Chancellor, Nicholas Piggin, Nick Desaulniers,
Oliver O'Halloran, Peter Ujfalusi, Pingfan Liu, Ram Pai, Randy Dunlap,
Russell Currey, Sam Bobroff, Sebastian Andrzej Siewior, Shawn
Anastasio, Stephen Rothwell, Steve Best, Sukadev Bhattiprolu, Thiago
Jung Bauermann, Tyrel Datwyler, Vaibhav Jain"
* tag 'powerpc-5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (131 commits)
powerpc: configs: Cleanup old Kconfig options
powerpc/configs/skiroot: Enable some more hardening options
powerpc/configs/skiroot: Disable xmon default & enable reboot on panic
powerpc/configs/skiroot: Enable security features
powerpc/configs/skiroot: Update for symbol movement only
powerpc/configs/skiroot: Drop default n CONFIG_CRYPTO_ECHAINIV
powerpc/configs/skiroot: Drop HID_LOGITECH
powerpc/configs: Drop NET_VENDOR_HP which moved to staging
powerpc/configs: NET_CADENCE became NET_VENDOR_CADENCE
powerpc/configs: Drop CONFIG_QLGE which moved to staging
powerpc: Do not consider weak unresolved symbol relocations as bad
powerpc/32s: Fix kasan_early_hash_table() for CONFIG_VMAP_STACK
powerpc: indent to improve Kconfig readability
powerpc: Provide initial documentation for PAPR hcalls
powerpc: Implement user_access_save() and user_access_restore()
powerpc: Implement user_access_begin and friends
powerpc/32s: Prepare prevent_user_access() for user_access_end()
powerpc/32s: Drop NULL addr verification
powerpc/kuap: Fix set direction in allow/prevent_user_access()
powerpc/32s: Fix bad_kuap_fault()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc
Pull remoteproc updates from Bjorn Andersson:
"This adds support for the Mediatek MT8183 SCP, modem remoteproc on
Qualcomm SC7180 platform, audio and sensor remoteprocs on Qualcomm
MSM8998 and audio, compute, modem and sensor remoteprocs on Qualcomm
SM8150.
It adds votes for necessary power-domains for all Qualcomm TrustZone
based remoteproc instances are held, fixes a bug related to remoteproc
drivers registering before the core has been initialized and does
clean up the Qualcomm modem remoteproc driver"
* tag 'rproc-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/andersson/remoteproc: (21 commits)
remoteproc: qcom: q6v5-mss: Improve readability of reset_assert
remoteproc: qcom: q6v5-mss: Use regmap_read_poll_timeout
remoteproc: qcom: q6v5-mss: Rename boot status timeout
remoteproc: qcom: q6v5-mss: Improve readability across clk handling
remoteproc: use struct_size() helper
remoteproc: Initialize rproc_class before use
rpmsg: add rpmsg support for mt8183 SCP.
remoteproc/mediatek: add SCP support for mt8183
dt-bindings: Add a binding for Mediatek SCP
remoteproc: mss: q6v5-mss: Add modem support on SC7180
dt-bindings: remoteproc: qcom: Add Q6V5 Modem PIL binding for SC7180
remoteproc: qcom: pas: Add MSM8998 ADSP and SLPI support
dt-bindings: remoteproc: qcom: Add ADSP and SLPI support for MSM8998 SoC
remoteproc: q6v5-mss: Remove mem clk from the active pool
remoteproc: qcom: Remove unneeded semicolon
remoteproc: qcom: pas: Add auto_boot flag
remoteproc: qcom: pas: Add SM8150 ADSP, CDSP, Modem and SLPI support
dt-bindings: remoteproc: qcom: SM8150 Add ADSP, CDSP, MPSS and SLPI support
remoteproc: qcom: pas: Vote for active/proxy power domains
dt-bindings: remoteproc: qcom: Add power-domain bindings for Q6V5 PAS
...
|
|
This makes the qcom,videocc bindings match the recent changes to the
dispcc and gpucc.
1. Switched to using "bi_tcxo" instead of "xo".
2. Adds a description for the XO clock. Not terribly important but
nice if it cleanly matches its cousins.
3. Updates the example to use the symbolic name for the RPMH clock and
also show that the real devices are currently using 2 address cells
/ size cells and fixes the spacing on the closing brace.
4. Split into 2 files. In this case they could probably share one
file, but let's be consistent.
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lkml.kernel.org/r/20200203103049.v4.11.I27bbd90045f38cd3218c259526409d52a48efb35@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The qcom,gpucc bindings had a few problems with them:
1. When things were converted to yaml the name of the "gpll0 main"
clock got changed from "gpll0" to "gpll0_main". Change it back for
msm8998.
2. Apparently there is a push not to use purist aliases for clocks but
instead to just use the internal Qualcomm names. For sdm845 and
sc7180 (where the drivers haven't already been changed) move in
this direction.
Things were also getting complicated harder to deal with by jamming
several SoCs into one file. Splitting simplifies things.
Fixes: 5c6f3a36b913 ("dt-bindings: clock: Add YAML schemas for the QCOM GPUCC clock bindings")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lkml.kernel.org/r/20200203103049.v4.7.I513cd73b16665065ae6c22cf594d8b543745e28c@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The qcom,dispcc bindings had a few problems with them:
1. They didn't specify all the clocks that dispcc is a client of.
Specifically on sc7180 there are two clocks from the DSI PHY and
two from the DP PHY. On sdm845 there are actually two DSI PHYs
(each of which has two clocks) and an extra clock from the gcc.
These all need to be specified.
2. The sdm845.dtsi has existed for quite some time without specifying
the clocks. The Linux driver was relying on global names to match
things up. While we should transition things, it should be noted
in the bindings.
3. The names used the bindings for "xo" and "gpll0" didn't match the
names that QC used for these clocks internally and this was causing
confusion / difficulty with their code generation tools. Switched
to the internal names to simplify everyone's lives. It's not quite
as clean in a purist sense but it should avoid headaches. This
officially changes the binding, but that seems OK in this case.
Also note that I updated the example.
Fixes: 5d28e44ba630 ("dt-bindings: clock: Add YAML schemas for the QCOM DISPCC clock bindings")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lkml.kernel.org/r/20200203103049.v4.2.I0c4bbb0f75a0880cd4bd90d8b267271e2375e0d0@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux
Pull RTC updates from Alexandre Belloni:
"The VL_READ and VL_CLR ioctls have been reworked to be more useful.
This will not break userspace as there are very few users and they are
using the integer value as a boolean.
Apart from that, two drivers were reworked and a few fixes here and
there for a net reduction of number of lines.
Summary:
Subsystem:
- the VL_READ and VL_CLR ioctls are now documented and their behavior
is unified across all the drivers.
- RTC_I2C_AND_SPI Kconfig option rework to avoid selecting both
REGMAP_I2C and REGMAP_SPI unecessarily.
Drivers:
- at91rm9200: remove deprecated procfs, add sam9x60, sama5d4 and
sama5d2 compatibles.
- cmos: solve lost interrupts issue on MS Surface 3
- hym8563: return proper errno when time is invalid
- rv3029: many fixes, nvram support"
* tag 'rtc-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux: (63 commits)
dt-bindings: rtc: at91rm9200: document clocks property
rtc: i2c/spi: Avoid inclusion of REGMAP support when not needed
rtc: Kconfig: select REGMAP_I2C when necessary
rtc: Kconfig: properly indent sd3078 entry
rtc: cmos: Refactor code by using the new dmi_get_bios_year() helper
rtc: cmos: Use predefined value for RTC IRQ on legacy x86
rtc: cmos: Stop using shared IRQ
rtc: tps6586x: Use IRQ_NOAUTOEN flag
rtc: at91rm9200: use FIELD_PREP/FIELD_GET
rtc: at91rm9200: avoid time readout in at91_rtc_setalarm
rtc: at91rm9200: move register definitions to C file
rtc: at91rm9200: add sama5d4 and sama5d2 compatibles
dt-bindings: rtc: at91rm9200: convert bindings to json-schema
rtc: at91rm9200: remove procfs information
dt-bindings: atmel, at91rm9200-rtc: add microchip, sam9x60-rtc
rtc: pcf8563: Use BIT
rtc: moxart: Convert to SPDX identifier
rtc: ds1343: Remove unused struct spi_device in struct ds1343_priv
rtc: rx8025: Remove struct i2c_client from struct rx8025_data
rtc: hym8563: Read the valid flag directly instead of caching it
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux
Pull clk updates from Stephen Boyd:
"There are a few changes to the core framework this time around, in
addition to the normal collection of driver updates to support new
SoCs, fix incorrect data, and convert various drivers to clk_hw based
APIs.
In the core, we allow clk_ops::init() to return an error code now so
that we can fail clk registration if the callback does something like
fail to allocate memory. We also add a new "terminate" clk_op so that
things done in clk_ops::init() can be undone, e.g. free memory. We
also spit out a warning now when critical clks fail to enable and we
support changing clk rates and enable/disable state through debugfs
when developers compile the kernel themselves.
On the driver front, we get support for what seems like a lot of
Qualcomm and NXP SoCs given that those vendors dominate the diffstat.
There are a couple new drivers for Xilinx and Amlogic SoCs too. The
updates are all small things like fixing the way glitch free muxes
switch parents, avoiding div-by-zero problems, or fixing data like
parent names. See the updates section below for more details.
Finally, the "basic" clk types have been converted to support
specifying parents with clk_hw pointers. This work includes an
overhaul of the fixed-rate clk type to be more modern by using clk_hw
APIs.
Core:
- Let clk_ops::init() return an error code
- Add a clk_ops::terminate() callback to undo clk_ops::init()
- Warn about critical clks that fail to enable or prepare
- Support dangerous debugfs actions on clks with dead code
New Drivers:
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Add a driver for BCLK of Freescale SAI cores
- Add cam, vpe and sgx clock support for TI dra7
- Add aess clock support for TI omap5
- Enable clks for CPUfreq on Allwinner A64 SoCs
- Add Amlogic meson8b DDR clock controller
- Add input clocks to Amlogic meson8b controllers
- Add SPIBSC (SPI FLASH) clock on Renesas RZ/A2
- i.MX8MP clk driver support
Updates:
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw
based APIs
- Detect more PRMCU variants in ux500 driver
- Adjust the composite clk type to new way of describing clk parents
- Fixes for clk controllers on qcom msm8998 SoCs
- Fix gmac main clock for TI dra7
- Move TI dra7-atl clock header to correct location
- Fix hidden node name dependency on TI clkctrl clocks
- Fix Amlogic meson8b mali clock update using the glitch free mux
- Fix Amlogic pll driver division by zero at init
- Prepare for split of Renesas R-Car H3 ES1.x and ES2.0+ config
symbols
- Switch more i.MX clk drivers to clk_hw based APIs
- Disable non-functional divider between pll4_audio_div and
pll4_post_div on imx6q
- Fix watchdog2 clock name typo in imx7ulp clock driver
- Set CLK_GET_RATE_NOCACHE flag for DRAM related clocks on i.MX8M
SoCs
- Suppress bind attrs for i.MX8M clock driver
- Add a big comment in imx8qxp-lpcg driver to tell why
devm_platform_ioremap_resource() shouldn't be used for the driver
- A correction on i.MX8MN usb1_ctrl parent clock setting"
* tag 'clk-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/clk/linux: (140 commits)
dt/bindings: clk: fsl,plldig: Drop 'bindings' from schema id
clk: ls1028a: Fix warning on clamp() usage
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input
Pull input updates from Dmitry Torokhov:
- a driver for SGI IOC3 PS/2 controller
- updates to driver for FocalTech FT5x06 series touch screen
controllers
- other assorted fixes
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input:
Input: synaptics-rmi4 - switch to reduced reporting mode
dt-bindings: touchscreen: Convert Goodix touchscreen to json-schema
dt-bindings: touchscreen: Add touchscreen schema
Input: add IOC3 serio driver
Input: axp20x-pek - enable wakeup for all AXP variants
Input: axp20x-pek - respect userspace wakeup configuration
Input: ads7846 - use new `delay` structure for SPI transfer delays
Input: edt-ft5x06 - use pm core to enable/disable the wake irq
Input: edt-ft5x06 - make wakeup-source switchable
Input: edt-ft5x06 - document wakeup-source capability
Input: edt-ft5x06 - alphabetical include reorder
Input: edt-ft5x06 - work around first register access error
Input: apbps2 - add __iomem to register struct
Input: axp20x-pek - make device attributes static
Input: elants_i2c - check Remark ID when attempting firmware update
|
|
The 'qcom,gcc.yaml' file failed self-validation (dt_binding_check)
because it required a property to be either (3 entries big),
(3 entries big), or (7 entries big), but not more than one of those
things. That didn't make a ton of sense.
This patch splits all of the exceptional device trees (AKA those that
would have needed if/then/else rules) from qcom,gcc.yaml. It also
cleans up some cruft found while doing that.
After this lands, this worked for me atop clk-next with just the known
error about msm8998:
for f in \
Documentation/devicetree/bindings/clock/qcom,gcc-apq8064.yaml \
Documentation/devicetree/bindings/clock/qcom,gcc-ipq8074.yaml \
Documentation/devicetree/bindings/clock/qcom,gcc-msm8996.yaml \
Documentation/devicetree/bindings/clock/qcom,gcc-msm8998.yaml \
Documentation/devicetree/bindings/clock/qcom,gcc-qcs404.yaml \
Documentation/devicetree/bindings/clock/qcom,gcc-sc7180.yaml \
Documentation/devicetree/bindings/clock/qcom,gcc-sm8150.yaml \
Documentation/devicetree/bindings/clock/qcom,gcc.yaml; do \
ARCH=arm64 make dtbs_check DT_SCHEMA_FILES=$f; \
done
I then picked this patch atop linux-next (next-20200129) and ran:
# Delete broken yaml:
rm Documentation/devicetree/bindings/pci/intel-gw-pcie.yaml
ARCH=arm64 make dt_binding_check | grep 'clock/qcom'
...and that didn't seem to indicate problems.
Arbitrary decisions made (yell if you want changed):
- Left all the older devices (where clocks / clock-names weren't
specified) in a single file.
- Didn't make clocks "required" for msm8996 but left them as listed.
This seems a little weird but it matches the old binding.
Misc cleanups as part of this patch:
- Fixed schema id to not have "bindings/" as per Rob [1].
- Listed include files as per Stephen.
- sm8150 was claimed to be same set of clocks as sc7180, but driver
and dts appear to say that "bi_tcxo_ao" doesn't exist. Fixed.
- In "apq8064", "#thermal-sensor-cells" was missing the "#".
- Got rid of "|" at the end of top description since spacing doesn't
matter.
- Changed indentation to consistently 2 spaces (it was 3 in some
places).
- Added period at the end of protected-clocks description.
- No space before ":".
- Updated sc7180/sm8150 example to use the 'qcom,rpmh.h' include.
- Updated sc7180/sm8150 example to use larger address/size cells as
per reality.
- Updated sc7180/sm8150 example to point to the sleep_clk rather than
<0>.
- Made it so that gcc-ipq8074 didn't require #power-domain-cells since
actual dts didn't have it and I got no hits from:
git grep _GDSC include/dt-bindings/clock/qcom,gcc-ipq8074.h
- Made it so that gcc-qcs404 didn't require #power-domain-cells since
actual dts didn't have it and I got no hits from:
git grep _GDSC include/dt-bindings/clock/qcom,gcc-qcs404.h
Noticed, but not done in this patch (volunteers needed):
- Add "aud_ref_clk" to sm8150 bindings / dts even though I found a
reference to it in "gcc-sm8150.c".
- Fix node name in actual ipq8074 to be "clock-controller" (it's gcc).
- Since the example doesn't need phandes to exist, in msm8998 could
just make up places providing some of the clocks currently bogused
out with <0>.
- On msm8998 clocks are listed as required but current dts doesn't
have them.
[1] https://lore.kernel.org/r/CAL_Jsq+_2E-bAbP9F6VYkWRp0crEyRGa5peuwP58-PZniVny7w@mail.gmail.com
Fixes: ab91f72e018a ("clk: qcom: gcc-msm8996: Fix parent for CLKREF clocks")
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Rob Herring <robh@kernel.org>
Reviewed-by: Jeffrey Hugo <jeffrey.l.hugo@gmail.com>
Link: https://lkml.kernel.org/r/20200203094843.v3.1.I4452dc951d7556ede422835268742b25a18b356b@changeid
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
Having 'bindings' in here causes a warning when checking the schema.
Documentation/devicetree/bindings/clock/fsl,plldig.yaml:
$id: relative path/filename doesn't match actual path or filename
expected: http://devicetree.org/schemas/clock/fsl,plldig.yaml#
Remove it.
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Wen He <wen.he_1@nxp.com>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20200203052507.93215-2-sboyd@kernel.org
Acked-by: Rob Herring <robh@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Add support for ROHM BD71828 PMICs and GPIOs
- Add support for Qualcomm Aqstic Audio Codecs WCD9340 and WCD9341
New Device Support:
- Add support for BD71828 to BD70528 RTC driver
- Add support for Intel's Jasper Lake to LPSS PCI
New Functionality:
- Add support for Power Key to ROHM BD71828
- Add support for Clocks to ROHM BD71828
- Add support for GPIOs to Dialog DA9062
- Add support for USB PD Notify to ChromiumOS EC
- Allow callers to specify args when requesting regmap lookup; syscon
Fix-ups:
- Improve error handling and sanity checking; atmel-hlcdc, dln2
- Device Tree support/documentation; bd71828, da9062, xylon,logicvc,
ab8500, max14577, atmel-usart
- Match devices using platform IDs; bd7xxxx
- Refactor BD718x7 regulator component; bd718x7-regulator
- Use standard interfaces/helpers; syscon, sm501
- Trivial (whitespace, spelling, etc); ab8500-core, Kconfig
- Remove unused code; db8500-prcmu, tqmx86
- Wait until boot has finished before accessing registers;
madera-core
- Provide missing register value defaults; cs47l15-tables
- Allow more time for hardware to reset; madera-core
Bug Fixes:
- Fix erroneous register values; rohm-bd70528
- Fix register volatility; axp20x, rn5t618
- Fix Kconfig dependencies; MFD_MAX77650
- Fix incorrect compatible string; da9062-core
- Fix syscon_regmap_lookup_by_phandle_args() stub; syscon"
* tag 'mfd-next-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (41 commits)
mfd: syscon: Fix syscon_regmap_lookup_by_phandle_args() dummy
mfd: wcd934x: Add support to wcd9340/wcd9341 codec
mfd: syscon: Add arguments support for syscon reference
mfd: rn5t618: Mark ADC control register volatile
dt-bindings: atmel-usart: Add microchip,sam9x60-{usart, dbgu}
dt-bindings: atmel-usart: Remove wildcard
mfd: cros_ec: Add cros-usbpd-notify subdevice
mfd: da9062: Fix watchdog compatible string
mfd: madera: Allow more time for hardware reset
mfd: cs47l15: Add missing register default
mfd: madera: Wait for boot done before accessing any other registers
mfd: Kconfig: Rename Samsung to lowercase
mfd: tqmx86: remove set but not used variable 'i2c_ien'
mfd: dbx500-prcmu: Drop DSI pll clock functions
mfd: dbx500-prcmu: Drop set_display_clocks()
mfd: max77650: Select REGMAP_IRQ in Kconfig
mfd: axp20x: Mark AXP20X_VBUS_IPSOUT_MGMT as volatile
mfd: ab8500: Fix ab8500-clk typo
mfd: intel-lpss: Add Intel Jasper Lake PCI IDs
dt-bindings: mfd: max14577: Add reference to max14040_battery.txt descriptions
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds
Pull LED updates from Pavel Machek:
- New driver for TI TPS6105X
- Add managed API to get a LED from a device driver
- Misc fixes and updates
* tag 'leds-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/pavel/linux-leds: (22 commits)
leds: lm3692x: Disable chip on brightness 0
leds: lm3692x: Split out lm3692x_leds_disable
leds: lm3692x: Move lm3692x_init and rename to lm3692x_leds_enable
leds: lm3692x: Make sure we don't exceed the maximum LED current
dt: bindings: lm3692x: Add led-max-microamp property
leds: lm3692x: Allow to configure over voltage protection
dt: bindings: lm3692x: Add ti,ovp-microvolt property
leds: populate the device's of_node
leds: Add managed API to get a LED from a device driver
leds: Add of_led_get() and led_put()
leds: lm3532: add pointer to documentation and fix typo
leds: lm3532: use extended registration so that LED can be used for backlight
leds: lm3642: remove warnings for bad strtol, cleanup gotos
leds: rb532: cleanup whitespace
ledtrig-pattern: fix email address quoting in MODULE_AUTHOR()
dt-bindings: mfd: update TI tps6105x chip bindings
leds: tps6105x: add driver for MFD chip LED mode
led: max77650: add of_match table
leds: bd2802: Convert to use GPIO descriptors
leds: pca963x: Fix open-drain initialization
...
|
|
Merge the user_access_begin() series from Christophe. This is based on
a commit from Linus that went into v5.5-rc7.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci
Pull PCI updates from Bjorn Helgaas:
"Resource management:
- Improve resource assignment for hot-added nested bridges, e.g.,
Thunderbolt (Nicholas Johnson)
Power management:
- Optionally print config space of devices before suspend (Chen Yu)
- Increase D3 delay for AMD Ryzen5/7 XHCI controllers (Daniel Drake)
Virtualization:
- Generalize DMA alias quirks (James Sewart)
- Add DMA alias quirk for PLX PEX NTB (James Sewart)
- Fix IOV memory leak (Navid Emamdoost)
AER:
- Log which device prevents error recovery (Yicong Yang)
Peer-to-peer DMA:
- Whitelist Intel SkyLake-E (Armen Baloyan)
Broadcom iProc host bridge driver:
- Apply PAXC quirk whether driver is built-in or module (Wei Liu)
Broadcom STB host bridge driver:
- Add Broadcom STB PCIe host controller driver (Jim Quinlan)
Intel Gateway SoC host bridge driver:
- Add driver for Intel Gateway SoC (Dilip Kota)
Intel VMD host bridge driver:
- Add support for DMA aliases on other buses (Jon Derrick)
- Remove dma_map_ops overrides (Jon Derrick)
- Remove now-unused X86_DEV_DMA_OPS (Christoph Hellwig)
NVIDIA Tegra host bridge driver:
- Fix Tegra30 afi_pex2_ctrl register offset (Marcel Ziswiler)
Panasonic UniPhier host bridge driver:
- Remove module code since driver can't be built as a module
(Masahiro Yamada)
Qualcomm host bridge driver:
- Add support for SDM845 PCIe controller (Bjorn Andersson)
TI Keystone host bridge driver:
- Fix "num-viewport" DT property error handling (Kishon Vijay Abraham I)
- Fix link training retries initiation (Yurii Monakov)
- Fix outbound region mapping (Yurii Monakov)
Misc:
- Add Switchtec Gen4 support (Kelvin Cao)
- Add Switchtec Intercomm Notify and Upstream Error Containment
support (Logan Gunthorpe)
- Use dma_set_mask_and_coherent() since Switchtec supports 64-bit
addressing (Wesley Sheng)"
* tag 'pci-v5.6-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/helgaas/pci: (60 commits)
PCI: Allow adjust_bridge_window() to shrink resource if necessary
PCI: Set resource size directly in adjust_bridge_window()
PCI: Rename extend_bridge_window() to adjust_bridge_window()
PCI: Rename extend_bridge_window() parameter
PCI: Consider alignment of hot-added bridges when assigning resources
PCI: Remove local variable usage in pci_bus_distribute_available_resources()
PCI: Pass size + alignment to pci_bus_distribute_available_resources()
PCI: Rename variables
PCI: vmd: Add two VMD Device IDs
PCI: Remove unnecessary braces
PCI: brcmstb: Add MSI support
PCI: brcmstb: Add Broadcom STB PCIe host controller driver
x86/PCI: Remove X86_DEV_DMA_OPS
PCI: vmd: Remove dma_map_ops overrides
iommu/vt-d: Remove VMD child device sanity check
iommu/vt-d: Use pci_real_dma_dev() for mapping
PCI: Introduce pci_real_dma_dev()
x86/PCI: Expose VMD's pci_dev in struct pci_sysdata
x86/PCI: Add to_pci_sysdata() helper
PCI/AER: Initialize aer_fifo
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- New staging driver for Rockship ISPv1 unit
- New staging driver for Rockchip MIPI Synopsys DPHY RX0
- y2038 fixes at V4L2 API (backward-compatible)
- A dvb core fix when receiving invalid EIT sections
- Some clang-specific warnings got fixed
- Added support for touch V4L2 interface at vivid
- Several drivers were converted to use the new
i2c_new_scanned_device() kAPI
- Added sm1 support at meson's vdec driver
- Several other driver cleanups, fixes and improvements
* tag 'media/v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (207 commits)
media: staging/intel-ipu3: remove TODO item about acronyms
media: v4l2-fwnode: Print the node name while parsing endpoints
media: Revert "media: staging/intel-ipu3: make imgu use fixed running mode"
media: mt9v111: constify copied structure
media: platform: VIDEO_MEDIATEK_JPEG can also depend on MTK_IOMMU
media: uvcvideo: Add a quirk to force GEO GC6500 Camera bits-per-pixel value
media: uvcvideo: Avoid cyclic entity chains due to malformed USB descriptors
media: hantro: fix post-processing NULL pointer dereference
media: rcar-vin: Use correct pixel format when aligning format
media: MAINTAINERS: add entry for Rockchip ISP1 driver
media: staging: rkisp1: add TODO file for staging
media: staging: rkisp1: add document for rkisp1 meta buffer format
media: staging: rkisp1: add output device for parameters
media: staging: rkisp1: add capture device for statistics
media: staging: rkisp1: add user space ABI definitions
media: staging: rkisp1: add streaming paths
media: staging: rkisp1: add Rockchip ISP1 base driver
media: staging: phy-rockchip-dphy-rx0: add Rockchip MIPI Synopsys DPHY RX0 driver
media: staging: dt-bindings: add Rockchip MIPI RX D-PHY RX0 yaml bindings
media: staging: dt-bindings: add Rockchip ISP1 yaml bindings
...
|
|
'clk-freescale' and 'clk-qoriq' into clk-next
- Support for Xilinx Versal platform clks
- Display clk controller on qcom sc7180
- Video clk controller on qcom sc7180
- Graphics clk controller on qcom sc7180
- CPU PLLs for qcom msm8916
- Fixes for clk controllers on qcom msm8998 SoCs
- Move qcom msm8974 gfx3d clk to RPM control
- Display port clk support on qcom sdm845 SoCs
- Global clk controller on qcom ipq6018
- Adjust composite clk to new way of describing clk parents
- Add a driver for BCLK of Freescale SAI cores
* clk-imx: (32 commits)
clk: imx: Add support for i.MX8MP clock driver
dt-bindings: imx: Add clock binding doc for i.MX8MP
clk: imx: gate4: Switch imx_clk_gate4_flags() to clk_hw based API
clk: imx: imx8mq: Switch to clk_hw based API
clk: imx: imx8mm: Switch to clk_hw based API
clk: imx: imx8mn: Switch to clk_hw based API
clk: imx: Remove __init for imx_obtain_fixed_clk_hw() API
clk: imx: gate3: Switch to clk_hw based API
clk: imx: add hw API imx_clk_hw_mux2_flags
clk: imx: add imx_unregister_hw_clocks
clk: imx: clk-composite-8m: Switch to clk_hw based API
clk: imx: clk-pll14xx: Switch to clk_hw based API
clk: imx7up: Rename the clks to hws
clk: imx: Rename the imx_clk_divider_gate to imply it's clk_hw based
clk: imx: Rename the imx_clk_pfdv2 to imply it's clk_hw based
clk: imx: Rename the imx_clk_pllv4 to imply it's clk_hw based
clk: imx: Rename sccg and frac pll register to suggest clk_hw
clk: imx: imx7ulp composite: Rename to show is clk_hw based
clk: imx: pllv2: Switch to clk_hw based API
clk: imx: pllv1: Switch to clk_hw based API
...
* clk-ti:
clk: ti: clkctrl: Fix hidden dependency to node name
clk: ti: add clkctrl data dra7 sgx
clk: ti: omap5: Add missing AESS clock
clk: ti: dra7: fix parent for gmac_clkctrl
clk: ti: dra7: add vpe clkctrl data
clk: ti: dra7: add cam clkctrl data
dt-bindings: clock: Move ti-dra7-atl.h to dt-bindings/clock
* clk-xilinx:
clk: zynqmp: Add support for clock with CLK_DIVIDER_POWER_OF_TWO flag
clk: zynqmp: Fix divider calculation
clk: zynqmp: Add support for get max divider
clk: zynqmp: Warn user if clock user are more than allowed
clk: zynqmp: Extend driver for versal
dt-bindings: clock: Add bindings for versal clock driver
* clk-nvidia:
clk: tegra20/30: Explicitly set parent clock for Video Decoder
clk: tegra20/30: Don't pre-initialize displays parent clock
clk: tegra: divider: Check UART's divider enable-bit state on rate's recalculation
clk: tegra: clk-dfll: Remove call to pm_runtime_irq_safe()
clk: tegra: Mark fuse clock as critical
* clk-qcom: (35 commits)
clk: qcom: rpmh: Sort OF match table
dt-bindings: fix warnings in validation of qcom,gcc.yaml
dt-binding: fix compilation error of the example in qcom,gcc.yaml
clk: qcom: Add ipq6018 Global Clock Controller support
clk: qcom: Add DT bindings for ipq6018 gcc clock controller
clk: qcom: gcc-msm8996: Fix parent for CLKREF clocks
clk: qcom: rpmh: Add IPA clock for SC7180
clk: qcom: rpmh: skip undefined clocks when registering
clk: qcom: Add video clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Video clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM VIDEOCC clock bindings
clk: qcom: Add graphics clock controller driver for SC7180
dt-bindings: clock: Introduce SC7180 QCOM Graphics clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM GPUCC clock bindings
clk: qcom: apcs-msm8916: use clk_parent_data to specify the parent
clk: qcom: Add display clock controller driver for SC7180
dt-bindings: clock: Introduce QCOM sc7180 display clock bindings
dt-bindings: clock: Add YAML schemas for the QCOM DISPCC clock bindings
clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration
clk: qcom: alpha-pll: Remove useless read from set rate
...
* clk-freescale:
clk: fsl-sai: new driver
dt-bindings: clock: document the fsl-sai driver
clk: composite: add _register_composite_pdata() variants
* clk-qoriq:
clk: qoriq: add ls1088a hwaccel clocks support
clk: ls1028a: Add clock driver for Display output interface
dt/bindings: clk: Add YAML schemas for LS1028A Display Clock bindings
|
|
'clk-amlogic' and 'clk-allwinner' into clk-next
- Support dangerous debugfs actions on clks with dead code
- Convert gpio, fixed-factor, mux, gate, divider basic clks to hw based APIs
* clk-debugfs-danger:
clk: Add support for setting clk_rate via debugfs
* clk-basic-hw:
clk: divider: Add support for specifying parents via DT/pointers
clk: gate: Add support for specifying parents via DT/pointers
clk: mux: Add support for specifying parents via DT/pointers
clk: asm9260: Use parent accuracy in fixed rate clk
clk: fixed-rate: Document that accuracy isn't a rate
clk: fixed-rate: Add clk flags for parent accuracy
clk: fixed-rate: Add support for specifying parents via DT/pointers
clk: fixed-rate: Document accuracy member
clk: fixed-rate: Move to_clk_fixed_rate() to C file
clk: fixed-rate: Remove clk_register_fixed_rate_with_accuracy()
clk: fixed-rate: Convert to clk_hw based APIs
clk: gpio: Use DT way of specifying parents
* clk-renesas:
clk: renesas: Prepare for split of R-Car H3 config symbol
dt-bindings: clock: renesas: cpg-mssr: Fix r8a774b1 typo
clk: renesas: r7s9210: Add SPIBSC clock
clk: renesas: rcar-gen3: Allow changing the RPC[D2] clocks
clk: renesas: Remove use of ARCH_R8A7796
clk: renesas: rcar-gen2: Change multipliers and dividers to u8
* clk-amlogic:
clk: clarify that clk_set_rate() does updates from top to bottom
clk: meson: meson8b: make the CCF use the glitch-free mali mux
clk: meson: pll: Fix by 0 division in __pll_params_to_rate()
clk: meson: g12a: fix missing uart2 in regmap table
clk: meson: meson8b: use of_clk_hw_register to register the clocks
clk: meson: meson8b: don't register the XTAL clock when provided via OF
clk: meson: meson8b: change references to the XTAL clock to use [fw_]name
clk: meson: meson8b: use clk_hw_set_parent in the CPU clock notifier
clk: meson: add a driver for the Meson8/8b/8m2 DDR clock controller
dt-bindings: clock: meson8b: add the clock inputs
dt-bindings: clock: add the Amlogic Meson8 DDR clock controller binding
* clk-allwinner:
clk: sunxi: a23/a33: Export the MIPI PLL
clk: sunxi: a31: Export the MIPI PLL
clk: sunxi-ng: a64: export CLK_CPUX clock for DVFS
clk: sunxi-ng: add mux and pll notifiers for A64 CPU clock
clk: sunxi-ng: r40: Export MBUS clock
clk: sunxi: use of_device_get_match_data
|
|
Pull MIPS changes from Paul Burton:
"Nothing too big or scary in here:
- Support mremap() for the VDSO, primarily to allow CRIU to restore
the VDSO to its checkpointed location.
- Restore the MIPS32 cBPF JIT, after having reverted the enablement
of the eBPF JIT for MIPS32 systems in the 5.5 cycle.
- Improve cop0 counter synchronization behaviour whilst onlining CPUs
by running with interrupts disabled.
- Better match FPU behaviour when emulating multiply-accumulate
instructions on pre-r6 systems that implement IEEE754-2008 style
MACs.
- Loongson64 kernels now build using the MIPS64r2 ISA, allowing them
to take advantage of instructions introduced by r2.
- Support for the Ingenic X1000 SoC & the really nice little CU Neo
development board that's using it.
- Support for WMAC on GARDENA Smart Gateway devices.
- Lots of cleanup & refactoring of SGI IP27 (Origin 2*) support in
preparation for introducing IP35 (Origin 3*) support.
- Various Kconfig & Makefile cleanups"
* tag 'mips_5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mips/linux: (60 commits)
MIPS: PCI: Add detection of IOC3 on IO7, IO8, IO9 and Fuel
MIPS: Loongson64: Disable exec hazard
MIPS: Loongson64: Bump ISA level to MIPSR2
MIPS: Make DIEI support as a config option
MIPS: OCTEON: octeon-irq: fix spelling mistake "to" -> "too"
MIPS: asm: local: add barriers for Loongson
MIPS: Loongson64: Select mac2008 only feature
MIPS: Add MAC2008 Support
Revert "MIPS: Add custom serial.h with BASE_BAUD override for generic kernel"
MIPS: sort MIPS and MIPS_GENERIC Kconfig selects alphabetically (again)
MIPS: make CPU_HAS_LOAD_STORE_LR opt-out
MIPS: generic: don't unconditionally select PINCTRL
MIPS: don't explicitly select LIBFDT in Kconfig
MIPS: sync-r4k: do slave counter synchronization with disabled HW interrupts
MIPS: SGI-IP30: Check for valid pointer before using it
MIPS: syscalls: fix indentation of the 'SYSNR' message
MIPS: boot: fix typo in 'vmlinux.lzma.its' target
MIPS: fix indentation of the 'RELOCS' message
dt-bindings: Document loongson vendor-prefix
MIPS: CU1000-Neo: Refresh defconfig to support HWMON and WiFi.
...
|
|
LS1028A has a clock domain PXLCLK0 used for provide pixel clocks to Display
output interface. Add a YAML schema for this.
Signed-off-by: Wen He <wen.he_1@nxp.com>
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lkml.kernel.org/r/20191213083402.35678-1-wen.he_1@nxp.com
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core
- block2mtd: page index should use pgoff_t
- maps: physmap: minimal Runtime PM support
- maps: pcmciamtd: avoid possible sleep-in-atomic-context bugs
- concat: Fix a comment referring to an unknown symbol
Raw NAND:
- Macronix: Use match_string() helper
- Atmel: switch to using devm_fwnode_gpiod_get()
- Denali: rework the SKIP_BYTES feature and add reset controlling
- Brcmnand: set appropriate DMA mask
- Cadence: add unspecified HAS_IOMEM dependency
- Various cleanup.
Onenand:
- Rename Samsung and Omap2 drivers to avoid possible build warnings
- Enable compile testing
- Various build issues
- Kconfig cleanup
SPI-NAND:
- Support for Toshiba TC58CVG2S0HRAIJ
SPI-NOR:
- Add support for TB selection using SR bit 6,
- Add support for few flashes"
* tag 'mtd/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (41 commits)
mtd: concat: Fix a comment referring to an unknown symbol
mtd: rawnand: add unspecified HAS_IOMEM dependency
mtd: block2mtd: page index should use pgoff_t
mtd: maps: physmap: Add minimal Runtime PM support
mtd: maps: pcmciamtd: fix possible sleep-in-atomic-context bugs in pcmciamtd_set_vpp()
mtd: onenand: Rename omap2 driver to avoid a build warning
mtd: onenand: Use a better name for samsung driver
mtd: rawnand: atmel: switch to using devm_fwnode_gpiod_get()
mtd: spinand: add support for Toshiba TC58CVG2S0HRAIJ
mtd: rawnand: macronix: Use match_string() helper to simplify the code
mtd: sharpslpart: Fix unsigned comparison to zero
mtd: onenand: Enable compile testing of OMAP and Samsung drivers
mtd: onenand: samsung: Fix printing format for size_t on 64-bit
mtd: onenand: samsung: Fix pointer cast -Wpointer-to-int-cast warnings on 64 bit
mtd: rawnand: denali: remove hard-coded DENALI_DEFAULT_OOB_SKIP_BYTES
mtd: rawnand: denali_dt: add reset controlling
dt-bindings: mtd: denali_dt: document reset property
mtd: rawnand: denali_dt: Add support for configuring SPARE_AREA_SKIP_BYTES
mtd: rawnand: denali_dt: error out if platform has no associated data
mtd: rawnand: brcmnand: Set appropriate DMA mask
...
|
|
Pull drm updates from Davbe Airlie:
"This is the main pull request for graphics for 5.6. Usual selection of
changes all over.
I've got one outstanding vmwgfx pull that touches mm so kept it
separate until after all of this lands. I'll try and get it to you
soon after this, but it might be early next week (nothing wrong with
code, just my schedule is messy)
This also hits a lot of fbdev drivers with some cleanups.
Other notables:
- vulkan timeline semaphore support added to syncobjs
- nouveau turing secureboot/graphics support
- Displayport MST display stream compression support
Detailed summary:
uapi:
- dma-buf heaps added (and fixed)
- command line add support for panel oreientation
- command line allow overriding penguin count
drm:
- mipi dsi definition updates
- lockdep annotations for dma_resv
- remove dma-buf kmap/kunmap support
- constify fb_ops in all fbdev drivers
- MST fix for daisy chained hotplug-
- CTA-861-G modes with VIC >= 193 added
- fix drm_panel_of_backlight export
- LVDS decoder support
- more device based logging support
- scanline alighment for dumb buffers
- MST DSC helpers
scheduler:
- documentation fixes
- job distribution improvements
panel:
- Logic PD type 28 panel support
- Jimax8729d MIPI-DSI
- igenic JZ4770
- generic DSI devicetree bindings
- sony acx424AKP panel
- Leadtek LTK500HD1829
- xinpeng XPP055C272
- AUO B116XAK01
- GiantPlus GPM940B0
- BOE NV140FHM-N49
- Satoz SAT050AT40H12R2
- Sharp LS020B1DD01D panels.
ttm:
- use blocking WW lock
i915:
- hw/uapi state separation
- Lock annotation improvements
- selftest improvements
- ICL/TGL DSI VDSC support
- VBT parsing improvments
- Display refactoring
- DSI updates + fixes
- HDCP 2.2 for CFL
- CML PCI ID fixes
- GLK+ fbc fix
- PSR fixes
- GEN/GT refactor improvments
- DP MST fixes
- switch context id alloc to xarray
- workaround updates
- LMEM debugfs support
- tiled monitor fixes
- ICL+ clock gating programming removed
- DP MST disable sequence fixed
- LMEM discontiguous object maps
- prefaulting for discontiguous objects
- use LMEM for dumb buffers if possible
- add LMEM mmap support
amdgpu:
- enable sync object timelines for vulkan
- MST atomic routines
- enable MST DSC support
- add DMCUB display microengine support
- DC OEM i2c support
- Renoir DC fixes
- Initial HDCP 2.x support
- BACO support for Arcturus
- Use BACO for runtime PM power save
- gfxoff on navi10
- gfx10 golden updates and fixes
- DCN support on POWER
- GFXOFF for raven1 refresh
- MM engine idle handlers cleanup
- 10bpc EDP panel fixes
- renoir watermark fixes
- SR-IOV fixes
- Arcturus VCN fixes
- GDDR6 training fixes
- freesync fixes
- Pollock support
amdkfd:
- unify more codepath with amdgpu
- use KIQ to setup HIQ rather than MMIO
radeon:
- fix vma fault handler race
- PPC DMA fix
- register check fixes for r100/r200
nouveau:
- mmap_sem vs dma_resv fix
- rewrite the ACR secure boot code for Turing
- TU10x graphics engine support (TU11x pending)
- Page kind mapping for turing
- 10-bit LUT support
- GP10B Tegra fixes
- HD audio regression fix
hisilicon/hibmc:
- use generic fbdev code and helpers
rockchip:
- dsi/px30 support
virtio:
- fb damage support
- static some functions
vc4:
- use dma_resv lock wrappers
msm:
- use dma_resv lock wrappers
- sc7180 display + DSI support
- a618 support
- UBWC support improvements
vmwgfx:
- updates + new logging uapi
exynos:
- enable/disable callback cleanups
etnaviv:
- use dma_resv lock wrappers
atmel-hlcdc:
- clock fixes
mediatek:
- cmdq support
- non-smooth cursor fixes
- ctm property support
sun4i:
- suspend support
- A64 mipi dsi support
rcar-du:
- Color management module support
- LVDS encoder dual-link support
- R8A77980 support
analogic:
- add support for an6345
ast:
- atomic modeset support
- primary plane garbage fix
arcgpu:
- fixes for fourcc handling
tegra:
- minor fixes and improvments
mcde:
- vblank support
meson:
- OSD1 plane AFBC commit
gma500:
- add pageflip support
- reomve global drm_dev
komeda:
- tweak debugfs output
- d32 support
- runtime PM suppotr
udl:
- use generic shmem helpers
- cleanup and fixes"
* tag 'drm-next-2020-01-30' of git://anongit.freedesktop.org/drm/drm: (1998 commits)
drm/nouveau/fb/gp102-: allow module to load even when scrubber binary is missing
drm/nouveau/acr: return error when registering LSF if ACR not supported
drm/nouveau/disp/gv100-: not all channel types support reporting error codes
drm/nouveau/disp/nv50-: prevent oops when no channel method map provided
drm/nouveau: support synchronous pushbuf submission
drm/nouveau: signal pending fences when channel has been killed
drm/nouveau: reject attempts to submit to dead channels
drm/nouveau: zero vma pointer even if we only unreference it rather than free
drm/nouveau: Add HD-audio component notifier support
drm/nouveau: fix build error without CONFIG_IOMMU_API
drm/nouveau/kms/nv04: remove set but not used variable 'width'
drm/nouveau/kms/nv50: remove set but not unused variable 'nv_connector'
drm/nouveau/mmu: fix comptag memory leak
drm/nouveau/gr/gp10b: Use gp100_grctx and gp100_gr_zbc
drm/nouveau/pmu/gm20b,gp10b: Fix Falcon bootstrapping
drm/exynos: Rename Exynos to lowercase
drm/exynos: change callback names
drm/mst: Don't do atomic checks over disabled managers
drm/amdgpu: add the lost mutex_init back
drm/amd/display: skip opp blank or unblank if test pattern enabled
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply
Pull power supply and reset updates from Sebastian Reichel:
"Core:
- Add battery internal resistance temperature table support
Drivers:
- sc27xx: Optimize the battery resistance with measuring temperature
- max17042-battery: Add MAX17055 support
- bq25890-charger: Add support of BQ25892 and BQ25896 chips
- misc fixes"
* tag 'for-v5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/sre/linux-power-supply: (44 commits)
power: supply: ipaq_micro_battery: remove unneeded semicolon
power: supply: bq25890_charger: fix incorrect error return when bq25890_field_read fails
power: supply: axp20x_usb_power: Only poll while offline
power: supply: axp20x_usb_power: Add wakeup control
power: supply: axp20x_usb_power: Allow offlining
power: supply: axp20x_usb_power: Use a match structure
power: suppy: ucs1002: Make the symbol 'ucs1002_regulator_enable' static
power: reset: at91-poweroff: use proper master clock register offset
power: reset: at91-poweroff: introduce struct shdwc_reg_config
power: supply: bq25890_charger: Add DT and I2C ids for all supported chips
dt-bindings: Add new chips to bq25890 binding documentation
power: supply: bq25890_charger: Add support of BQ25892 and BQ25896 chips
power: supply: core: Update sysfs-class-power ABI document
power: supply: sbs-battery: Fix a signedness bug in sbs_get_battery_capacity()
power: supply: ltc2941-battery-gauge: fix use-after-free
power: supply: max17040: Correct IRQ wake handling
power: supply: axp20x_usb_power: Remove unused device_node
power: supply: axp20x_ac_power: Add wakeup control
power: supply: axp20x_ac_power: Allow offlining
power: supply: axp20x_ac_power: Fix reporting online status
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull devicetree updates from Rob Herring:
- Update dtc to upstream v1.5.1-22-gc40aeb60b47a (plus 1 revert)
- Fix for DMA coherent devices on Power
- Rework and simplify the DT phandle cache code
- DT schema conversions for LEDS, gpio-leds, STM32 dfsdm, STM32 UART,
STM32 ROMEM, STM32 watchdog, STM32 DMAs, STM32 mlahb, STM32 RTC,
STM32 RCC, STM32 syscon, rs485, Renesas rCar CSI2, Faraday FTIDE010,
DWC2, Arm idle-states, Allwinner legacy resets, PRCM and clocks,
Allwinner H6 OPP, Allwinner AHCI, Allwinner MBUS, Allwinner A31 CSI,
Allwinner h/w codec, Allwinner A10 system ctrl, Allwinner SRAM,
Allwinner USB PHY, Renesas CEU, generic PCI host, Arm Versatile PCI
- New binding schemas for SATA and PATA controllers, TI and Infineon VR
controllers, MAX31730
- New compatible strings for i.MX8QM, WCN3991, renesas,r8a77961-wdt,
renesas,etheravb-r8a77961
- Add USB 'super-speed-plus' as a documented speed
- Vendor prefixes for broadmobi, calaosystems, kam, and mps
- Clean-up the multiple flavors of ST-Ericsson vendor prefixes
* tag 'devicetree-for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (66 commits)
scripts/dtc: Revert "yamltree: Ensure consistent bracketing of properties with phandles"
of: Add OF_DMA_DEFAULT_COHERENT & select it on powerpc
dt-bindings: leds: Convert gpio-leds to DT schema
dt-bindings: leds: Convert common LED binding to schema
dt-bindings: PCI: Convert generic host binding to DT schema
dt-bindings: PCI: Convert Arm Versatile binding to DT schema
dt-bindings: Be explicit about installing deps
dt-bindings: stm32: convert dfsdm to json-schema
dt-bindings: serial: Convert STM32 UART to json-schema
dt-bindings: serial: Convert rs485 bindings to json-schema
dt-bindings: timer: Use non-empty ranges in example
dt-bindings: arm-boards: typo fix
dt-bindings: Add TI and Infineon VR Controllers as trivial devices
dt-binding: usb: add "super-speed-plus"
dt-bindings: rcar-csi2: Convert bindings to json-schema
dt-bindings: iio: adc: ad7606: Fix wrong maxItems value
dt-bindings: Convert Faraday FTIDE010 to DT schema
dt-bindings: Create DT bindings for PATA controllers
dt-bindings: Create DT bindings for SATA controllers
dt: bindings: add vendor prefix for Kamstrup A/S
...
|
|
- Add DT clock/reset info for SDM845 PCIe controller (Bjorn Andersson)
- Add support for SDM845 PCIe controller to the qcom driver (Bjorn
Andersson)
* remotes/lorenzo/pci/qcom:
PCI: qcom: Add support for SDM845 PCIe controller
dt-bindings: PCI: qcom: Add support for SDM845 PCIe
|
|
- Add intel-gw driver for PCIe host controller on Intel Gateway SoC
(Dilip Kota)
- Use shared DesignWare helpers to configure Fast Training Sequence (FTS)
in artpec6 (Dilip Kota)
* remotes/lorenzo/pci/dwc:
PCI: artpec6: Configure FTS with dwc helper function
PCI: dwc: intel: PCIe RC controller driver
dt-bindings: PCI: intel: Add YAML schemas for the PCIe RC controller
|
|
i2c/for-5.6
The main feature is the idle-state rework of the pca954x driver from Biwen Li.
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/brgl/linux into i2c/for-5.6
at24 updates for linux v5.6
- minor maintenance: update the license tag, sort headers
- move support for the write-protect pin into nvmem core
- add a reference to the new wp-gpios property in nvmem to at25 bindings
- add support for regulator and pm_runtime control
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big char/misc/whatever driver changes for 5.6-rc1
Included in here are loads of things from a variety of different
driver subsystems:
- soundwire updates
- binder updates
- nvmem updates
- firmware drivers updates
- extcon driver updates
- various misc driver updates
- fpga driver updates
- interconnect subsystem and driver updates
- bus driver updates
- uio driver updates
- mei driver updates
- w1 driver cleanups
- various other small driver updates
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (86 commits)
mei: me: add jasper point DID
char: hpet: Use flexible-array member
binder: fix log spam for existing debugfs file creation.
mei: me: add comet point (lake) H device ids
nvmem: add QTI SDAM driver
dt-bindings: nvmem: add binding for QTI SPMI SDAM
dt-bindings: imx-ocotp: Add i.MX8MP compatible
dt-bindings: soundwire: fix example
soundwire: cadence: fix kernel-doc parameter descriptions
soundwire: intel: report slave_ids for each link to SOF driver
siox: Use the correct style for SPDX License Identifier
w1: omap-hdq: Simplify driver with PM runtime autosuspend
firmware: stratix10-svc: Remove unneeded semicolon
firmware: google: Probe for a GSMI handler in firmware
firmware: google: Unregister driver_info on failure and exit in gsmi
firmware: google: Release devices before unregistering the bus
slimbus: qcom: add missed clk_disable_unprepare in remove
slimbus: Use the correct style for SPDX License Identifier
slimbus: qcom-ngd-ctrl: Use dma_request_chan() instead dma_request_slave_channel()
dt-bindings: SLIMBus: add slim devices optional properties
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging
Pull staging and IIO updates from Greg KH:
"Here is the big staging/iio driver patches for 5.6-rc1
Included in here are:
- lots of new IIO drivers and updates for that subsystem
- the usual huge quantity of minor cleanups for staging drivers
- removal of the following staging drivers:
- isdn/avm
- isdn/gigaset
- isdn/hysdn
- octeon-usb
- octeon ethernet
Overall we deleted far more lines than we added, removing over 40k of
old and obsolete driver code.
All of these changes have been in linux-next for a while with no
reported issues"
* tag 'staging-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/staging: (353 commits)
staging: most: usb: check for NULL device
staging: next: configfs: fix release link
staging: most: core: fix logging messages
staging: most: core: remove container struct
staging: most: remove struct device core driver
staging: most: core: drop device reference
staging: most: remove device from interface structure
staging: comedi: drivers: fix spelling mistake "to" -> "too"
staging: exfat: remove fs_func struct.
staging: wilc1000: avoid mutex unlock without lock in wilc_wlan_handle_txq()
staging: wilc1000: return zero on success and non-zero on function failure
staging: axis-fifo: replace spinlock with mutex
staging: wilc1000: remove unused code prior to throughput enhancement in SPI
staging: wilc1000: added 'wilc_' prefix for 'struct assoc_resp' name
staging: wilc1000: move firmware API struct's to separate header file
staging: wilc1000: remove use of infinite loop conditions
staging: kpc2000: rename variables with kpc namespace
staging: vt6656: Remove memory buffer from vnt_download_firmware.
staging: vt6656: Just check NEWRSR_DECRYPTOK for RX_FLAG_DECRYPTED.
staging: vt6656: Use vnt_rx_tail struct for tail variables.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb
Pull USB/Thunderbolt/PHY driver updates from Greg KH:
"Here is the big USB and Thunderbolt and PHY driver updates for
5.6-rc1.
With the advent of USB4, "Thunderbolt" has really become USB4, so the
renaming of the Kconfig option and starting to share subsystem code
has begun, hence both subsystems coming in through the same tree here.
PHY driver updates also touched USB drivers, so that is coming in
through here as well.
Major stuff included in here are:
- USB 4 initial support added (i.e. Thunderbolt)
- musb driver updates
- USB gadget driver updates
- PHY driver updates
- USB PHY driver updates
- lots of USB serial stuff fixed up
- USB typec updates
- USB-IP fixes
- lots of other smaller USB driver updates
All of these have been in linux-next for a while now (the usb-serial
tree is already tested in linux-next on its own before merged into
here), with no reported issues"
[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
that causes configuration warnings - Linus ]
* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
Doc: ABI: add usb charger uevent
usb: phy: show USB charger type for user
usb: cdns3: fix spelling mistake and rework grammar in text
usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
USB: serial: ir-usb: simplify endpoint check
USB: serial: ir-usb: make set_termios synchronous
USB: serial: ir-usb: fix IrLAP framing
USB: serial: ir-usb: fix link-speed handling
USB: serial: ir-usb: add missing endpoint sanity check
usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
usb: typec: tcpci: mask event interrupts when remove driver
usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
usb: chipidea: handle single role for usb role class
usb: musb: fix spelling mistake: "periperal" -> "peripheral"
phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
USB: usbfs: Always unlink URBs in reverse order
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl
Pull pin control updates from Linus Walleij:
"This is the bulk of pin control changes, nothing too exciting about
this.
Some changes hit arch/sh and arch/arm but are well isolated and
acknowledged by the respective arch maintainers.
Core changes:
- Dropped the chained IRQ setup callback into GPIOLIB as we got rid
of the last users of that in this changeset.
New drivers:
- New driver for Ingenic X1830.
- New driver for Freescale i.MX8MP.
Driver enhancements:
- Fix all remaining Intel drivers to pass their IRQ chips along with
the GPIO chips.
- Intel Baytrail allocates its irqchip dynamically.
- Intel Lynxpoint is thoroughly rewritten and modernized.
- Aspeed AST2600 pin muxing and configuration is much improved.
- Qualcomm SC7180 functions are updated and wakeup interrupt map is
provided.
- A whole slew of Renesas SH-PFC cleanups and improvements.
- Fix up the Intel DT bindings to use the generic YAML DT bindings
schema (a first user of this)"
* tag 'pinctrl-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-pinctrl: (99 commits)
pinctrl: madera: Remove extra blank line
pinctrl: qcom: Don't lock around irq_set_irq_wake()
pinctrl: mvebu: armada-37xx: use use platform api
gpio: Drop the chained IRQ handler assign function
pinctrl: freescale: Add i.MX8MP pinctrl driver support
dt-bindings: imx: Add pinctrl binding doc for i.MX8MP
pinctrl: tigerlake: Tiger Lake uses _HID enumeration
pinctrl: sunrisepoint: Add Coffee Lake-S ACPI ID
pinctrl: iproc: Use platform_get_irq_optional() to avoid error message
pinctrl: dt-bindings: Fix some errors in the lgm and pinmux schema
pinctrl: intel: Pass irqchip when adding gpiochip
pinctrl: intel: Add GPIO <-> pin mapping ranges via callback
pinctrl: baytrail: Replace WARN with dev_info_once when setting direct-irq pin to output
pinctrl: baytrail: Do not clear IRQ flags on direct-irq enabled pins
pinctrl: sunrisepoint: Add missing Interrupt Status register offset
pinctrl: sh-pfc: Split R-Car H3 support in two independent drivers
pinctrl: artpec6: fix __iomem on reg in set
pinctrl: ingenic: Use devm_platform_ioremap_resource()
pinctrl: ingenic: Factorize irq_set_type function
pinctrl: ingenic: Remove duplicated ingenic_chip_info structures
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v5.6 kernel cycle.
This is a pretty calm cycle so far, nothing special going on really.
Some more changes will come in from the irqchip and pin control trees.
I also deleted an orphan include file for FMC that was dangling since
subsystem was removed.
Core changes:
- Document the usecases for the kernelspace vs userspace handling of
GPIOs.
- Handle MSI (message signalled interrupts) properly in the core
hierarchical irqdomain code.
- Fix a rare race condition while initializing the descriptor array.
New drivers:
- Xylon LogiCVC GPIO driver.
- WDC934x GPIO controller driver.
Driver improvements:
- Implemented suspend/resume in the Tegra driver.
- MPC8xx edge detection fixup.
- Properly convert ThunderX to use hierarchical irqdomain with
GPIOLIB_IRQCHIP on top of the revert of the previous buggy
switchover. This time it works (hopefully).
Misc:
- Drop a FMC remnant file <linux/ipmi-fru.h>
- A slew of fixes"
* tag 'gpio-v5.6-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (48 commits)
MAINTAINERS: Replace Tien Hock Loh as Altera PIO maintainer
gpiolib: hold gpio devices lock until ->descs array is initialised
gpio: aspeed-sgpio: fixed typos
gpio: mvebu: clear irq in edge cause register before unmask edge irq
gpiolib: Lower verbosity when allocating hierarchy irq
gpiolib: Remove duplicated function gpio_do_set_config()
gpio: Fix the no return statement warning
gpio: wcd934x: Add support to wcd934x gpio controller
gpiolib: remove set but not used variable 'config'
gpio: vx855: fixed a typo
gpio: mockup: sort headers alphabetically
gpio: mockup: update the license tag
gpio: Remove the unused flags
gpiolib: Set lockdep class for hierarchical irq domains
gpio: thunderx: Switch to GPIOLIB_IRQCHIP
gpiolib: Add the support for the msi parent domain
gpiolib: Add support for the irqdomain which doesn't use irq_fwspec as arg
gpio: Add use guidance documentation
dt-bindings: gpio: wcd934x: Add bindings for gpio
gpio: altera: change to platform_get_irq_optional to avoid false-positive error
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux
Pull thermal updates from Daniel Lezcano:
- Depromote debug print on the db8500 platform (Linus Walleij)
- Fix compilation warning when compiling with make W=1 (Amit Kucheria)
- Code cleanup and refactoring, regmap conversion and add hwmon support
on Qoriq (Andrey Smirnov)
- Add an idle injection cpu cooling device and its documentation,
rename the cpu_cooling device to cpufreq_cooling device (Daniel
Lezcano)
- Convert unexported functions to static, add the __init annotation in
the thermal-of code and remove the pointless wrapper functions
(Daniel Lezcano)
- Fix register offset for Armada XP and register reset bit
initialization (Zak Hays)
- Enable hwmon on the rockchip (Stefan Schaeckeler)
- Add the thermal sensor for the H6/H5/H3/A64/A83T/R40 sun8i platform
and their device tree bindings, followed by a fix for the ths number
and the sparse warnings (Yangtao Li)
- Code cleansup for the sun8i and hwmon support (Yangtao Li)
- Silent some messages which are misleading given the changes made in
the previous version on generic-adc (Martin Blumenstingl)
- Rename exynos to Exynos (Krzysztof Kozlowski)
- Add the bcm2711 thermal driver with the device tree bindings (Stefan
Wahren)
- Use usleep_range() instead of udelay() as the call is always done in
a sleep-able context (Geert Uytterhoeven)
- Do code cleanup and re-organization to set the scene for a new
process for the brcmstb (Florian Fainelli)
- Fix bindings check issues on brcm (Stefan Wahren)
- Add Jasper Lake support on int340x (Nivedita Swaminathan)
- Add Comet Lake support on intel pch (Gayatri Kammela)
- Fix unmatched pci_release_region() on x86 (Chuhong Yuan)
- Remove temperature boundaries for rcar and rcar3 (Niklas Söderlund)
- Fix return value to -ENODEV when thermal_zone_of_sensor_register() is
called with the of-node is missing (Peter Mamonov)
- Code cleanup, interrupt bouncing, and better support on stm32 (Pascal
Paillet)
* tag 'thermal-v5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/thermal/linux: (66 commits)
thermal: stm32: Fix low threshold interrupt flood
thermal: stm32: Improve temperature computing
thermal: stm32: Handle multiple trip points
thermal: stm32: Disable interrupts at probe
thermal: stm32: Rework sensor mode management
thermal: stm32: Fix icifr register name
thermal: of: Make thermal_zone_of_sensor_register return -ENODEV if a sensor OF node is missing
thermal: rcar_gen3_thermal: Remove temperature bound
thermal: rcar_thermal: Remove temperature bound
thermal: intel: intel_pch_thermal: Add Comet Lake (CML) platform support
thermal: intel: Fix unmatched pci_release_region
thermal: int340x: processor_thermal: Add Jasper Lake support
dt-bindings: brcm,avs-ro-thermal: Fix binding check issues
thermal: brcmstb_thermal: Register different ops per process
thermal: brcmstb_thermal: Restructure interrupt registration
thermal: brcmstb_thermal: Add 16nm process thermal parameters
dt-bindings: thermal: Define BCM7216 thermal sensor compatible
thermal: brcmstb_thermal: Prepare to support a different process
thermal: brcmstb_thermal: Do not use DT coefficients
thermal: rcar_thermal: Use usleep_range() instead of udelay()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound
Pull sound updates from Takashi Iwai:
"As the diffstat shows we've had again a lot of works done for this
cycle: the majority of changes are the continued componentization and
code refactoring in ASoC, the tree-wide PCM API updates and cleanups
and SOF updates while a few ASoC driver updates are seen, too.
Here we go, some highlights:
Core:
- Finally y2038 support landed to ALSA ABI; some ioctls have been
extended and lots of tricks were applied
- Applying the new managed PCM buffer API to all drivers; the API
itself was already merged in 5.5
- The already deprecated dimension support in ALSA control API is
dropped completely now
- Verification of ALSA control elements to catch API misuses
ASoC:
- Further code refactorings and moving things to the component level
- Lots of updates and improvements on SOF / Intel drivers; now
including common HDMI driver and SoundWire support
- New driver support for Ingenic JZ4770, Mediatek MT6660, Qualcomm
WCD934x and WSA881x, and Realtek RT700, RT711, RT715, RT1011,
RT1015 and RT1308
HD-audio:
- Improved ring-buffer communications using waitqueue
- Drop the superfluous buffer preallocation on x86
Others:
- Many code cleanups, mostly constifications over the whole tree
- USB-audio: quirks for MOTU, Corsair Virtuoso, Line6 Helix
- FireWire: code refactoring for oxfw and dice drivers"
* tag 'sound-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/tiwai/sound: (638 commits)
ALSA: usb-audio: add quirks for Line6 Helix devices fw>=2.82
ALSA: hda: Add Clevo W65_67SB the power_save blacklist
ASoC: soc-core: remove null_snd_soc_ops
ASoC: soc-pcm: add soc_rtd_trigger()
ASoC: soc-pcm: add soc_rtd_hw_free()
ASoC: soc-pcm: add soc_rtd_hw_params()
ASoC: soc-pcm: add soc_rtd_prepare()
ASoC: soc-pcm: add soc_rtd_shutdown()
ASoC: soc-pcm: add soc_rtd_startup()
ASoC: rt1015: add rt1015 amplifier driver
ASoC: madera: Correct some kernel doc
ASoC: topology: fix soc_tplg_fe_link_create() - link->dobj initialization order
ASoC: Intel: skl_hda_dsp_common: Fix global-out-of-bounds bug
ASoC: madera: Correct DMIC only input hook ups
ALSA: cs46xx: fix spelling mistake "to" -> "too"
ALSA: hda - Add docking station support for Lenovo Thinkpad T420s
ASoC: Add MediaTek MT6660 Speaker Amp Driver
ASoC: dt-bindings: rt5645: add suppliers
ASoC: max98090: fix deadlock in max98090_dapm_put_enum_double()
ASoC: dapm: add snd_soc_dapm_put_enum_double_locked
...
|
|
Pull networking updates from David Miller:
1) Add WireGuard
2) Add HE and TWT support to ath11k driver, from John Crispin.
3) Add ESP in TCP encapsulation support, from Sabrina Dubroca.
4) Add variable window congestion control to TIPC, from Jon Maloy.
5) Add BCM84881 PHY driver, from Russell King.
6) Start adding netlink support for ethtool operations, from Michal
Kubecek.
7) Add XDP drop and TX action support to ena driver, from Sameeh
Jubran.
8) Add new ipv4 route notifications so that mlxsw driver does not have
to handle identical routes itself. From Ido Schimmel.
9) Add BPF dynamic program extensions, from Alexei Starovoitov.
10) Support RX and TX timestamping in igc, from Vinicius Costa Gomes.
11) Add support for macsec HW offloading, from Antoine Tenart.
12) Add initial support for MPTCP protocol, from Christoph Paasch,
Matthieu Baerts, Florian Westphal, Peter Krystad, and many others.
13) Add Octeontx2 PF support, from Sunil Goutham, Geetha sowjanya, Linu
Cherian, and others.
* git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1469 commits)
net: phy: add default ARCH_BCM_IPROC for MDIO_BCM_IPROC
udp: segment looped gso packets correctly
netem: change mailing list
qed: FW 8.42.2.0 debug features
qed: rt init valid initialization changed
qed: Debug feature: ilt and mdump
qed: FW 8.42.2.0 Add fw overlay feature
qed: FW 8.42.2.0 HSI changes
qed: FW 8.42.2.0 iscsi/fcoe changes
qed: Add abstraction for different hsi values per chip
qed: FW 8.42.2.0 Additional ll2 type
qed: Use dmae to write to widebus registers in fw_funcs
qed: FW 8.42.2.0 Parser offsets modified
qed: FW 8.42.2.0 Queue Manager changes
qed: FW 8.42.2.0 Expose new registers and change windows
qed: FW 8.42.2.0 Internal ram offsets modifications
MAINTAINERS: Add entry for Marvell OcteonTX2 Physical Function driver
Documentation: net: octeontx2: Add RVU HW and drivers overview
octeontx2-pf: ethtool RSS config support
octeontx2-pf: Add basic ethtool support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto updates from Herbert Xu:
"API:
- Removed CRYPTO_TFM_RES flags
- Extended spawn grabbing to all algorithm types
- Moved hash descsize verification into API code
Algorithms:
- Fixed recursive pcrypt dead-lock
- Added new 32 and 64-bit generic versions of poly1305
- Added cryptogams implementation of x86/poly1305
Drivers:
- Added support for i.MX8M Mini in caam
- Added support for i.MX8M Nano in caam
- Added support for i.MX8M Plus in caam
- Added support for A33 variant of SS in sun4i-ss
- Added TEE support for Raven Ridge in ccp
- Added in-kernel API to submit TEE commands in ccp
- Added AMD-TEE driver
- Added support for BCM2711 in iproc-rng200
- Added support for AES256-GCM based ciphers for chtls
- Added aead support on SEC2 in hisilicon"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (244 commits)
crypto: arm/chacha - fix build failured when kernel mode NEON is disabled
crypto: caam - add support for i.MX8M Plus
crypto: x86/poly1305 - emit does base conversion itself
crypto: hisilicon - fix spelling mistake "disgest" -> "digest"
crypto: chacha20poly1305 - add back missing test vectors and test chunking
crypto: x86/poly1305 - fix .gitignore typo
tee: fix memory allocation failure checks on drv_data and amdtee
crypto: ccree - erase unneeded inline funcs
crypto: ccree - make cc_pm_put_suspend() void
crypto: ccree - split overloaded usage of irq field
crypto: ccree - fix PM race condition
crypto: ccree - fix FDE descriptor sequence
crypto: ccree - cc_do_send_request() is void func
crypto: ccree - fix pm wrongful error reporting
crypto: ccree - turn errors to debug msgs
crypto: ccree - fix AEAD decrypt auth fail
crypto: ccree - fix typo in comment
crypto: ccree - fix typos in error msgs
crypto: atmel-{aes,sha,tdes} - Retire crypto_platform_data
crypto: x86/sha - Eliminate casts on asm implementations
...
|
|
The clocks property is mandatory, document it.
Reported-by: Rob Herring <robh+dt@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Link: https://lore.kernel.org/r/20200128204200.22201-1-alexandre.belloni@bootlin.com
Signed-off-by: Alexandre Belloni <alexandre.belloni@bootlin.com>
|
|
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Rob Herring <robh@kernel.org>
Link: https://lkml.kernel.org/r/20200102231101.11834-2-michael@walle.cc
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
|
The last example in qcom,gcc.yaml set 'sleep' as the second
value of 'clock-names'. According to the schema is should
be 'sleep_clk'. Fix the example to conform the schema.
This fixes a warning when validating the schema:
"clock-names: ... is not valid under any of the given schemas"
Signed-off-by: Dafna Hirschfeld <dafna.hirschfeld@collabora.com>
Link: https://lkml.kernel.org/r/20200122135741.12123-1-dafna.hirschfeld@collabora.com
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>
|
