Merge tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb

Pull USB/Thunderbolt/PHY driver updates from Greg KH:
 "Here is the big USB and Thunderbolt and PHY driver updates for
  5.6-rc1.

  With the advent of USB4, "Thunderbolt" has really become USB4, so the
  renaming of the Kconfig option and starting to share subsystem code
  has begun, hence both subsystems coming in through the same tree here.

  PHY driver updates also touched USB drivers, so that is coming in
  through here as well.

  Major stuff included in here are:
   - USB 4 initial support added (i.e. Thunderbolt)
   - musb driver updates
   - USB gadget driver updates
   - PHY driver updates
   - USB PHY driver updates
   - lots of USB serial stuff fixed up
   - USB typec updates
   - USB-IP fixes
   - lots of other smaller USB driver updates

  All of these have been in linux-next for a while now (the usb-serial
  tree is already tested in linux-next on its own before merged into
  here), with no reported issues"

[ Removed an incorrect compile test enablement for PHY_EXYNOS5250_SATA
  that causes configuration warnings    - Linus ]

* tag 'usb-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/usb: (207 commits)
  Doc: ABI: add usb charger uevent
  usb: phy: show USB charger type for user
  usb: cdns3: fix spelling mistake and rework grammar in text
  usb: phy: phy-gpio-vbus-usb: Convert to GPIO descriptors
  USB: serial: cyberjack: fix spelling mistake "To" -> "Too"
  USB: serial: ir-usb: simplify endpoint check
  USB: serial: ir-usb: make set_termios synchronous
  USB: serial: ir-usb: fix IrLAP framing
  USB: serial: ir-usb: fix link-speed handling
  USB: serial: ir-usb: add missing endpoint sanity check
  usb: typec: fusb302: fix "op-sink-microwatt" default that was in mW
  usb: typec: wcove: fix "op-sink-microwatt" default that was in mW
  usb: dwc3: pci: add ID for the Intel Comet Lake -V variant
  usb: typec: tcpci: mask event interrupts when remove driver
  usb: host: xhci-tegra: set MODULE_FIRMWARE for tegra186
  usb: chipidea: add inline for ci_hdrc_host_driver_init if host is not defined
  usb: chipidea: handle single role for usb role class
  usb: musb: fix spelling mistake: "periperal" -> "peripheral"
  phy: ti: j721e-wiz: Fix build error without CONFIG_OF_ADDRESS
  USB: usbfs: Always unlink URBs in reverse order
  ...

11 files changed, 540 insertions, 62 deletions

diff --git a/Documentation/devicetree/bindings/connector/usb-connector.txt b/Documentation/devicetree/bindings/connector/usb-connector.txt
index d357987181ee..88578ac1a8a7 100644
--- a/Documentation/devicetree/bindings/connector/usb-connector.txt
+++ b/Documentation/devicetree/bindings/connector/usb-connector.txt
@@ -1,8 +1,8 @@
 USB Connector
 =============
 
-USB connector node represents physical USB connector. It should be
-a child of USB interface controller.
+A USB connector node represents a physical USB connector. It should be
+a child of a USB interface controller.
 
 Required properties:
 - compatible: describes type of the connector, must be one of:
diff --git a/Documentation/devicetree/bindings/phy/allwinner,sun9i-a80-usb-phy.yaml b/Documentation/devicetree/bindings/phy/allwinner,sun9i-a80-usb-phy.yaml
new file mode 100644
index 000000000000..ded7d6f0a119
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/allwinner,sun9i-a80-usb-phy.yaml
@@ -0,0 +1,135 @@
+# SPDX-License-Identifier: GPL-2.0
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/allwinner,sun9i-a80-usb-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Allwinner A80 USB PHY Device Tree Bindings
+
+maintainers:
+  - Chen-Yu Tsai <wens@csie.org>
+  - Maxime Ripard <mripard@kernel.org>
+
+properties:
+  "#phy-cells":
+    const: 0
+
+  compatible:
+    const: allwinner,sun9i-a80-usb-phy
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    anyOf:
+      - description: Main PHY Clock
+
+      - items:
+          - description: Main PHY clock
+          - description: HSIC 12MHz clock
+          - description: HSIC 480MHz clock
+
+  clock-names:
+    oneOf:
+      - const: phy
+
+      - items:
+          - const: phy
+          - const: hsic_12M
+          - const: hsic_480M
+
+  resets:
+    anyOf:
+      - description: Normal USB PHY reset
+
+      - items:
+          - description: Normal USB PHY reset
+          - description: HSIC Reset
+
+  reset-names:
+    oneOf:
+      - const: phy
+
+      - items:
+          - const: phy
+          - const: hsic
+
+  phy_type:
+    const: hsic
+    description:
+      When absent, the PHY type will be assumed to be normal USB.
+
+  phy-supply:
+    description:
+      Regulator that powers VBUS
+
+required:
+  - "#phy-cells"
+  - compatible
+  - reg
+  - clocks
+  - clock-names
+  - resets
+  - reset-names
+
+additionalProperties: false
+
+if:
+  properties:
+    phy_type:
+      const: hsic
+
+  required:
+    - phy_type
+
+then:
+  properties:
+    clocks:
+      maxItems: 3
+
+    clock-names:
+      maxItems: 3
+
+    resets:
+      maxItems: 2
+
+    reset-names:
+      maxItems: 2
+
+examples:
+  - |
+    #include <dt-bindings/clock/sun9i-a80-usb.h>
+    #include <dt-bindings/reset/sun9i-a80-usb.h>
+
+    usbphy1: phy@a00800 {
+        compatible = "allwinner,sun9i-a80-usb-phy";
+        reg = <0x00a00800 0x4>;
+        clocks = <&usb_clocks CLK_USB0_PHY>;
+        clock-names = "phy";
+        resets = <&usb_clocks RST_USB0_PHY>;
+        reset-names = "phy";
+        phy-supply = <&reg_usb1_vbus>;
+        #phy-cells = <0>;
+    };
+
+  - |
+    #include <dt-bindings/clock/sun9i-a80-usb.h>
+    #include <dt-bindings/reset/sun9i-a80-usb.h>
+
+    usbphy3: phy@a02800 {
+        compatible = "allwinner,sun9i-a80-usb-phy";
+        reg = <0x00a02800 0x4>;
+        clocks = <&usb_clocks CLK_USB2_PHY>,
+                 <&usb_clocks CLK_USB_HSIC>,
+                 <&usb_clocks CLK_USB2_HSIC>;
+        clock-names = "phy",
+                      "hsic_12M",
+                      "hsic_480M";
+        resets = <&usb_clocks RST_USB2_PHY>,
+                 <&usb_clocks RST_USB2_HSIC>;
+        reset-names = "phy",
+                      "hsic";
+        phy_type = "hsic";
+        phy-supply = <&reg_usb3_vbus>;
+        #phy-cells = <0>;
+    };
diff --git a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
index 24a0d06acd1d..698aacbdcfc4 100644
--- a/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
+++ b/Documentation/devicetree/bindings/phy/brcm,brcmstb-usb-phy.txt
@@ -1,30 +1,49 @@
 Broadcom STB USB PHY
 
 Required properties:
- - compatible: brcm,brcmstb-usb-phy
- - reg: two offset and length pairs.
-	The first pair specifies a manditory set of memory mapped
-	registers used for general control of the PHY.
-	The second pair specifies optional registers used by some of
-	the SoCs that support USB 3.x
- - #phy-cells: Shall be 1 as it expects one argument for setting
-	       the type of the PHY. Possible values are:
-	       - PHY_TYPE_USB2 for USB1.1/2.0 PHY
-	       - PHY_TYPE_USB3 for USB3.x PHY
+- compatible: should be one of
+	"brcm,brcmstb-usb-phy"
+	"brcm,bcm7216-usb-phy"
+	"brcm,bcm7211-usb-phy"
+
+- reg and reg-names properties requirements are specific to the
+  compatible string.
+  "brcm,brcmstb-usb-phy":
+    - reg: 1 or 2 offset and length pairs. One for the base CTRL registers
+           and an optional pair for systems with USB 3.x support
+    - reg-names: not specified
+  "brcm,bcm7216-usb-phy":
+    - reg: 3 offset and length pairs for CTRL, XHCI_EC and XHCI_GBL
+           registers
+    - reg-names: "ctrl", "xhci_ec", "xhci_gbl"
+  "brcm,bcm7211-usb-phy":
+    - reg: 5 offset and length pairs for CTRL, XHCI_EC, XHCI_GBL,
+           USB_PHY and USB_MDIO registers and an optional pair
+	   for the BDC registers
+    - reg-names: "ctrl", "xhci_ec", "xhci_gbl", "usb_phy", "usb_mdio", "bdc_ec"
+
+- #phy-cells: Shall be 1 as it expects one argument for setting
+	      the type of the PHY. Possible values are:
+	      - PHY_TYPE_USB2 for USB1.1/2.0 PHY
+	      - PHY_TYPE_USB3 for USB3.x PHY
 
 Optional Properties:
 - clocks : clock phandles.
 - clock-names: String, clock name.
+- interrupts: wakeup interrupt
+- interrupt-names: "wakeup"
 - brcm,ipp: Boolean, Invert Port Power.
   Possible values are: 0 (Don't invert), 1 (Invert)
 - brcm,ioc: Boolean, Invert Over Current detection.
   Possible values are: 0 (Don't invert), 1 (Invert)
-NOTE: one or both of the following two properties must be set
-- brcm,has-xhci: Boolean indicating the phy has an XHCI phy.
-- brcm,has-eohci: Boolean indicating the phy has an EHCI/OHCI phy.
 - dr_mode: String, PHY Device mode.
   Possible values are: "host", "peripheral ", "drd" or "typec-pd"
   If this property is not defined, the phy will default to "host" mode.
+- brcm,syscon-piarbctl: phandle to syscon for handling config registers
+NOTE: one or both of the following two properties must be set
+- brcm,has-xhci: Boolean indicating the phy has an XHCI phy.
+- brcm,has-eohci: Boolean indicating the phy has an EHCI/OHCI phy.
+
 
 Example:
 
@@ -41,3 +60,27 @@ usbphy_0: usb-phy@f0470200 {
 	clocks = <&usb20>, <&usb30>;
 	clock-names = "sw_usb", "sw_usb3";
 };
+
+usb-phy@29f0200 {
+	reg = <0x29f0200 0x200>,
+		<0x29c0880 0x30>,
+		<0x29cc100 0x534>,
+		<0x2808000 0x24>,
+		<0x2980080 0x8>;
+	reg-names = "ctrl",
+		"xhci_ec",
+		"xhci_gbl",
+		"usb_phy",
+		"usb_mdio";
+	brcm,ioc = <0x0>;
+	brcm,ipp = <0x0>;
+	compatible = "brcm,bcm7211-usb-phy";
+	interrupts = <0x30>;
+	interrupt-parent = <&vpu_intr1_nosec_intc>;
+	interrupt-names = "wake";
+	#phy-cells = <0x1>;
+	brcm,has-xhci;
+	syscon-piarbctl = <&syscon_piarbctl>;
+	clocks = <&scmi_clk 256>;
+	clock-names = "sw_usb";
+};
diff --git a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt
index b640845fec67..c03ad2198410 100644
--- a/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt
+++ b/Documentation/devicetree/bindings/phy/brcm-sata-phy.txt
@@ -2,6 +2,7 @@
 
 Required properties:
 - compatible: should be one or more of
+     "brcm,bcm7216-sata-phy"
      "brcm,bcm7425-sata-phy"
      "brcm,bcm7445-sata-phy"
      "brcm,iproc-ns2-sata-phy"
diff --git a/Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml b/Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml
new file mode 100644
index 000000000000..ff7959c21af0
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/intel,lgm-emmc-phy.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/phy/intel,lgm-emmc-phy.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Intel Lightning Mountain(LGM) eMMC PHY Device Tree Bindings
+
+maintainers:
+  - Ramuthevar Vadivel Murugan <vadivel.muruganx.ramuthevar@linux.intel.com>
+
+description: |+
+  Bindings for eMMC PHY on Intel's Lightning Mountain SoC, syscon
+  node is used to reference the base address of eMMC phy registers.
+
+  The eMMC PHY node should be the child of a syscon node with the
+  required property:
+
+  - compatible:         Should be one of the following:
+                        "intel,lgm-syscon", "syscon"
+  - reg:
+      maxItems: 1
+
+properties:
+  compatible:
+      const: intel,lgm-emmc-phy
+
+  "#phy-cells":
+    const: 0
+
+  reg:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+required:
+  - "#phy-cells"
+  - compatible
+  - reg
+  - clocks
+
+examples:
+  - |
+    sysconf: chiptop@e0200000 {
+      compatible = "intel,lgm-syscon", "syscon";
+      reg = <0xe0200000 0x100>;
+
+      emmc-phy: emmc-phy@a8 {
+        compatible = "intel,lgm-emmc-phy";
+        reg = <0x00a8 0x10>;
+        clocks = <&emmc>;
+        #phy-cells = <0>;
+      };
+    };
+...
diff --git a/Documentation/devicetree/bindings/phy/phy-cadence-sierra.txt b/Documentation/devicetree/bindings/phy/phy-cadence-sierra.txt
index 6e1b47bfce43..03f5939d3d19 100644
--- a/Documentation/devicetree/bindings/phy/phy-cadence-sierra.txt
+++ b/Documentation/devicetree/bindings/phy/phy-cadence-sierra.txt
@@ -2,21 +2,24 @@ Cadence Sierra PHY
 -----------------------
 
 Required properties:
-- compatible:	cdns,sierra-phy-t0
-- clocks:	Must contain an entry in clock-names.
-		See ../clocks/clock-bindings.txt for details.
-- clock-names:	Must be "phy_clk"
+- compatible:	Must be "cdns,sierra-phy-t0" for Sierra in Cadence platform
+		Must be "ti,sierra-phy-t0" for Sierra in TI's J721E SoC.
 - resets:	Must contain an entry for each in reset-names.
 		See ../reset/reset.txt for details.
 - reset-names:	Must include "sierra_reset" and "sierra_apb".
 		"sierra_reset" must control the reset line to the PHY.
 		"sierra_apb" must control the reset line to the APB PHY
-		interface.
+		interface ("sierra_apb" is optional).
 - reg:		register range for the PHY.
 - #address-cells: Must be 1
 - #size-cells:	Must be 0
 
 Optional properties:
+- clocks:		Must contain an entry in clock-names.
+			See ../clocks/clock-bindings.txt for details.
+- clock-names:		Must contain "cmn_refclk_dig_div" and
+			"cmn_refclk1_dig_div" for configuring the frequency of
+			the clock to the lanes. "phy_clk" is deprecated.
 - cdns,autoconf:	A boolean property whose presence indicates that the
 			PHY registers will be configured by hardware. If not
 			present, all sub-node optional properties must be
diff --git a/Documentation/devicetree/bindings/phy/rockchip,px30-dsi-dphy.yaml b/Documentation/devicetree/bindings/phy/rockchip,px30-dsi-dphy.yaml
index bb0da87bcd84..476c56a1dc8c 100644
--- a/Documentation/devicetree/bindings/phy/rockchip,px30-dsi-dphy.yaml
+++ b/Documentation/devicetree/bindings/phy/rockchip,px30-dsi-dphy.yaml
@@ -13,9 +13,6 @@ properties:
   "#phy-cells":
     const: 0
 
-  "#clock-cells":
-    const: 0
-
   compatible:
     enum:
       - rockchip,px30-dsi-dphy
@@ -49,7 +46,6 @@ properties:
 
 required:
   - "#phy-cells"
-  - "#clock-cells"
   - compatible
   - reg
   - clocks
@@ -66,7 +62,6 @@ examples:
         reg = <0x0 0xff2e0000 0x0 0x10000>;
         clocks = <&pmucru 13>, <&cru 12>;
         clock-names = "ref", "pclk";
-        #clock-cells = <0>;
         resets = <&cru 12>;
         reset-names = "apb";
         #phy-cells = <0>;
diff --git a/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt b/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt
deleted file mode 100644
index 64f7109aea1f..000000000000
--- a/Documentation/devicetree/bindings/phy/sun9i-usb-phy.txt
+++ /dev/null
@@ -1,37 +0,0 @@
-Allwinner sun9i USB PHY
------------------------
-
-Required properties:
-- compatible : should be one of
-  * allwinner,sun9i-a80-usb-phy
-- reg : a list of offset + length pairs
-- #phy-cells : from the generic phy bindings, must be 0
-- phy_type : "hsic" for HSIC usage;
-	     other values or absence of this property indicates normal USB
-- clocks : phandle + clock specifier for the phy clocks
-- clock-names : depending on the "phy_type" property,
-  * "phy" for normal USB
-  * "hsic_480M", "hsic_12M" for HSIC
-- resets : a list of phandle + reset specifier pairs
-- reset-names : depending on the "phy_type" property,
-  * "phy" for normal USB
-  * "hsic" for HSIC
-
-Optional Properties:
-- phy-supply : from the generic phy bindings, a phandle to a regulator that
-	       provides power to VBUS.
-
-It is recommended to list all clocks and resets available.
-The driver will only use those matching the phy_type.
-
-Example:
-	usbphy1: phy@a01800 {
-		compatible = "allwinner,sun9i-a80-usb-phy";
-		reg = <0x00a01800 0x4>;
-		clocks = <&usb_phy_clk 2>, <&usb_phy_clk 10>,
-		       <&usb_phy_clk 3>;
-		clock-names = "hsic_480M", "hsic_12M", "phy";
-		resets = <&usb_phy_clk 18>, <&usb_phy_clk 19>;
-		reset-names = "hsic", "phy";
-		#phy-cells = <0>;
-	};
diff --git a/Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml b/Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml
new file mode 100644
index 000000000000..452cee1aed32
--- /dev/null
+++ b/Documentation/devicetree/bindings/phy/ti,phy-j721e-wiz.yaml
@@ -0,0 +1,221 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+# Copyright (C) 2019 Texas Instruments Incorporated - http://www.ti.com/
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/phy/ti,phy-j721e-wiz.yaml#"
+$schema: "http://devicetree.org/meta-schemas/core.yaml#"
+
+title: TI J721E WIZ (SERDES Wrapper)
+
+maintainers:
+  - Kishon Vijay Abraham I <kishon@ti.com>
+
+properties:
+  compatible:
+    enum:
+      - ti,j721e-wiz-16g
+      - ti,j721e-wiz-10g
+
+  power-domains:
+    maxItems: 1
+
+  clocks:
+    maxItems: 3
+    description: clock-specifier to represent input to the WIZ
+
+  clock-names:
+    items:
+      - const: fck
+      - const: core_ref_clk
+      - const: ext_ref_clk
+
+  num-lanes:
+    minimum: 1
+    maximum: 4
+
+  "#address-cells":
+    const: 1
+
+  "#size-cells":
+    const: 1
+
+  "#reset-cells":
+    const: 1
+
+  ranges: true
+
+  assigned-clocks:
+    maxItems: 2
+
+  assigned-clock-parents:
+    maxItems: 2
+
+  typec-dir-gpios:
+    maxItems: 1
+    description:
+      GPIO to signal Type-C cable orientation for lane swap.
+      If GPIO is active, lane 0 and lane 1 of SERDES will be swapped to
+      achieve the funtionality of an external type-C plug flip mux.
+
+  typec-dir-debounce-ms:
+    minimum: 100
+    maximum: 1000
+    default: 100
+    description:
+      Number of milliseconds to wait before sampling typec-dir-gpio.
+      If not specified, the default debounce of 100ms will be used.
+      Type-C spec states minimum CC pin debounce of 100 ms and maximum
+      of 200 ms. However, some solutions might need more than 200 ms.
+
+patternProperties:
+  "^pll[0|1]-refclk$":
+    type: object
+    description: |
+      WIZ node should have subnodes for each of the PLLs present in
+      the SERDES.
+    properties:
+      clocks:
+        maxItems: 2
+        description: Phandle to clock nodes representing the two inputs to PLL.
+
+      "#clock-cells":
+        const: 0
+
+      assigned-clocks:
+        maxItems: 1
+
+      assigned-clock-parents:
+        maxItems: 1
+
+    required:
+      - clocks
+      - "#clock-cells"
+      - assigned-clocks
+      - assigned-clock-parents
+
+  "^cmn-refclk1?-dig-div$":
+    type: object
+    description:
+      WIZ node should have subnodes for each of the PMA common refclock
+      provided by the SERDES.
+    properties:
+      clocks:
+        maxItems: 1
+        description: Phandle to the clock node representing the input to the
+          divider clock.
+
+      "#clock-cells":
+        const: 0
+
+    required:
+      - clocks
+      - "#clock-cells"
+
+  "^refclk-dig$":
+    type: object
+    description: |
+      WIZ node should have subnode for refclk_dig to select the reference
+      clock source for the reference clock used in the PHY and PMA digital
+      logic.
+    properties:
+      clocks:
+        maxItems: 4
+        description: Phandle to four clock nodes representing the inputs to
+          refclk_dig
+
+      "#clock-cells":
+        const: 0
+
+      assigned-clocks:
+        maxItems: 1
+
+      assigned-clock-parents:
+        maxItems: 1
+
+    required:
+      - clocks
+      - "#clock-cells"
+      - assigned-clocks
+      - assigned-clock-parents
+
+  "^serdes@[0-9a-f]+$":
+    type: object
+    description: |
+      WIZ node should have '1' subnode for the SERDES. It could be either
+      Sierra SERDES or Torrent SERDES. Sierra SERDES should follow the
+      bindings specified in
+      Documentation/devicetree/bindings/phy/phy-cadence-sierra.txt
+      Torrent SERDES should follow the bindings specified in
+      Documentation/devicetree/bindings/phy/phy-cadence-dp.txt
+
+required:
+  - compatible
+  - power-domains
+  - clocks
+  - clock-names
+  - num-lanes
+  - "#address-cells"
+  - "#size-cells"
+  - "#reset-cells"
+  - ranges
+
+examples:
+  - |
+    #include <dt-bindings/soc/ti,sci_pm_domain.h>
+
+    wiz@5000000 {
+           compatible = "ti,j721e-wiz-16g";
+           #address-cells = <1>;
+           #size-cells = <1>;
+           power-domains = <&k3_pds 292 TI_SCI_PD_EXCLUSIVE>;
+           clocks = <&k3_clks 292 5>, <&k3_clks 292 11>, <&dummy_cmn_refclk>;
+           clock-names = "fck", "core_ref_clk", "ext_ref_clk";
+           assigned-clocks = <&k3_clks 292 11>, <&k3_clks 292 0>;
+           assigned-clock-parents = <&k3_clks 292 15>, <&k3_clks 292 4>;
+           num-lanes = <2>;
+           #reset-cells = <1>;
+           ranges = <0x5000000 0x5000000 0x10000>;
+
+           pll0-refclk {
+                  clocks = <&k3_clks 293 13>, <&dummy_cmn_refclk>;
+                  #clock-cells = <0>;
+                  assigned-clocks = <&wiz1_pll0_refclk>;
+                  assigned-clock-parents = <&k3_clks 293 13>;
+           };
+
+           pll1-refclk {
+                  clocks = <&k3_clks 293 0>, <&dummy_cmn_refclk1>;
+                  #clock-cells = <0>;
+                  assigned-clocks = <&wiz1_pll1_refclk>;
+                  assigned-clock-parents = <&k3_clks 293 0>;
+           };
+
+           cmn-refclk-dig-div {
+                  clocks = <&wiz1_refclk_dig>;
+                  #clock-cells = <0>;
+           };
+
+           cmn-refclk1-dig-div {
+                  clocks = <&wiz1_pll1_refclk>;
+                  #clock-cells = <0>;
+           };
+
+           refclk-dig {
+                  clocks = <&k3_clks 292 11>, <&k3_clks 292 0>, <&dummy_cmn_refclk>, <&dummy_cmn_refclk1>;
+                  #clock-cells = <0>;
+                  assigned-clocks = <&wiz0_refclk_dig>;
+                  assigned-clock-parents = <&k3_clks 292 11>;
+           };
+
+           serdes@5000000 {
+                  compatible = "cdns,ti,sierra-phy-t0";
+                  reg-names = "serdes";
+                  reg = <0x5000000 0x10000>;
+                  #address-cells = <1>;
+                  #size-cells = <0>;
+                  resets = <&serdes_wiz0 0>;
+                  reset-names = "sierra_reset";
+                  clocks = <&wiz0_cmn_refclk_dig_div>, <&wiz0_cmn_refclk1_dig_div>;
+                  clock-names = "cmn_refclk_dig_div", "cmn_refclk1_dig_div";
+           };
+    };
diff --git a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
index cfc9f40ab641..51376cbe5f3d 100644
--- a/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
+++ b/Documentation/devicetree/bindings/usb/ci-hdrc-usb2.txt
@@ -15,6 +15,10 @@ Required properties:
 	"qcom,ci-hdrc"
 	"chipidea,usb2"
 	"xlnx,zynq-usb-2.20a"
+	"nvidia,tegra20-udc"
+	"nvidia,tegra30-udc"
+	"nvidia,tegra114-udc"
+	"nvidia,tegra124-udc"
 - reg: base address and length of the registers
 - interrupts: interrupt for the USB controller
 
diff --git a/Documentation/devicetree/bindings/usb/mediatek,musb.txt b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
new file mode 100644
index 000000000000..2b8a87c90d9e
--- /dev/null
+++ b/Documentation/devicetree/bindings/usb/mediatek,musb.txt
@@ -0,0 +1,57 @@
+MediaTek musb DRD/OTG controller
+-------------------------------------------
+
+Required properties:
+ - compatible      : should be one of:
+                     "mediatek,mt2701-musb"
+                     ...
+                     followed by "mediatek,mtk-musb"
+ - reg             : specifies physical base address and size of
+                     the registers
+ - interrupts      : interrupt used by musb controller
+ - interrupt-names : must be "mc"
+ - phys            : PHY specifier for the OTG phy
+ - dr_mode         : should be one of "host", "peripheral" or "otg",
+                     refer to usb/generic.txt
+ - clocks          : a list of phandle + clock-specifier pairs, one for
+                     each entry in clock-names
+ - clock-names     : must contain "main", "mcu", "univpll"
+                     for clocks of controller
+
+Optional properties:
+ - power-domains   : a phandle to USB power domain node to control USB's
+                     MTCMOS
+
+Required child nodes:
+ usb connector node as defined in bindings/connector/usb-connector.txt
+Optional properties:
+ - id-gpios        : input GPIO for USB ID pin.
+ - vbus-gpios      : input GPIO for USB VBUS pin.
+ - vbus-supply     : reference to the VBUS regulator, needed when supports
+                     dual-role mode
+ - usb-role-switch : use USB Role Switch to support dual-role switch, see
+                     usb/generic.txt.
+
+Example:
+
+usb2: usb@11200000 {
+	compatible = "mediatek,mt2701-musb",
+		     "mediatek,mtk-musb";
+	reg = <0 0x11200000 0 0x1000>;
+	interrupts = <GIC_SPI 32 IRQ_TYPE_LEVEL_LOW>;
+	interrupt-names = "mc";
+	phys = <&u2port2 PHY_TYPE_USB2>;
+	dr_mode = "otg";
+	clocks = <&pericfg CLK_PERI_USB0>,
+		 <&pericfg CLK_PERI_USB0_MCU>,
+		 <&pericfg CLK_PERI_USB_SLV>;
+	clock-names = "main","mcu","univpll";
+	power-domains = <&scpsys MT2701_POWER_DOMAIN_IFR_MSC>;
+	usb-role-switch;
+	connector{
+		compatible = "gpio-usb-b-connector", "usb-b-connector";
+		type = "micro";
+		id-gpios = <&pio 44 GPIO_ACTIVE_HIGH>;
+		vbus-supply = <&usb_vbus>;
+	};
+};