diff options
Diffstat (limited to 'net/wimax')
| -rw-r--r-- | net/wimax/Kconfig | 38 | ||||
| -rw-r--r-- | net/wimax/Makefile | 13 | ||||
| -rw-r--r-- | net/wimax/debug-levels.h | 42 | ||||
| -rw-r--r-- | net/wimax/debugfs.c | 90 | ||||
| -rw-r--r-- | net/wimax/id-table.c | 142 | ||||
| -rw-r--r-- | net/wimax/op-msg.c | 421 | ||||
| -rw-r--r-- | net/wimax/op-reset.c | 143 | ||||
| -rw-r--r-- | net/wimax/op-rfkill.c | 532 | ||||
| -rw-r--r-- | net/wimax/stack.c | 599 | ||||
| -rw-r--r-- | net/wimax/wimax-internal.h | 91 |
10 files changed, 2111 insertions, 0 deletions
diff --git a/net/wimax/Kconfig b/net/wimax/Kconfig new file mode 100644 index 000000000000..0bdbb6928205 --- /dev/null +++ b/net/wimax/Kconfig @@ -0,0 +1,38 @@ +# +# WiMAX LAN device configuration +# + +menuconfig WIMAX + tristate "WiMAX Wireless Broadband support" + help + + Select to configure support for devices that provide + wireless broadband connectivity using the WiMAX protocol + (IEEE 802.16). + + Please note that most of these devices require signing up + for a service plan with a provider. + + The different WiMAX drivers can be enabled in the menu entry + + Device Drivers > Network device support > WiMAX Wireless + Broadband devices + + If unsure, it is safe to select M (module). + +config WIMAX_DEBUG_LEVEL + int "WiMAX debug level" + depends on WIMAX + default 8 + help + + Select the maximum debug verbosity level to be compiled into + the WiMAX stack code. + + By default, debug messages are disabled at runtime and can + be selectively enabled for different parts of the code using + the sysfs debug-levels file. + + If set at zero, this will compile out all the debug code. + + It is recommended that it is left at 8. diff --git a/net/wimax/Makefile b/net/wimax/Makefile new file mode 100644 index 000000000000..5b80b941c2c9 --- /dev/null +++ b/net/wimax/Makefile @@ -0,0 +1,13 @@ + +obj-$(CONFIG_WIMAX) += wimax.o + +wimax-y := \ + id-table.o \ + op-msg.o \ + op-reset.o \ + op-rfkill.o \ + stack.o + +wimax-$(CONFIG_DEBUG_FS) += debugfs.o + + diff --git a/net/wimax/debug-levels.h b/net/wimax/debug-levels.h new file mode 100644 index 000000000000..1c29123a3aa9 --- /dev/null +++ b/net/wimax/debug-levels.h @@ -0,0 +1,42 @@ +/* + * Linux WiMAX Stack + * Debug levels control file for the wimax module + * + * + * Copyright (C) 2007-2008 Intel Corporation <linux-wimax@intel.com> + * Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License version + * 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA + * 02110-1301, USA. + */ +#ifndef __debug_levels__h__ +#define __debug_levels__h__ + +/* Maximum compile and run time debug level for all submodules */ +#define D_MODULENAME wimax +#define D_MASTER CONFIG_WIMAX_DEBUG_LEVEL + +#include <linux/wimax/debug.h> + +/* List of all the enabled modules */ +enum d_module { + D_SUBMODULE_DECLARE(debugfs), + D_SUBMODULE_DECLARE(id_table), + D_SUBMODULE_DECLARE(op_msg), + D_SUBMODULE_DECLARE(op_reset), + D_SUBMODULE_DECLARE(op_rfkill), + D_SUBMODULE_DECLARE(stack), +}; + +#endif /* #ifndef __debug_levels__h__ */ diff --git a/net/wimax/debugfs.c b/net/wimax/debugfs.c new file mode 100644 index 000000000000..87cf4430079c --- /dev/null +++ b/net/wimax/debugfs.c @@ -0,0 +1,90 @@ +/* + * Linux WiMAX + * Debugfs support + * + * + * Copyright (C) 2005-2006 Intel Corporation <linux-wimax@intel.com> + * Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License version + * 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA + * 02110-1301, USA. + */ +#include <linux/debugfs.h> +#include <linux/wimax.h> +#include "wimax-internal.h" + +#define D_SUBMODULE debugfs +#include "debug-levels.h" + + +/* Debug framework control of debug levels */ +struct d_level D_LEVEL[] = { + D_SUBMODULE_DEFINE(debugfs), + D_SUBMODULE_DEFINE(id_table), + D_SUBMODULE_DEFINE(op_msg), + D_SUBMODULE_DEFINE(op_reset), + D_SUBMODULE_DEFINE(op_rfkill), + D_SUBMODULE_DEFINE(stack), +}; +size_t D_LEVEL_SIZE = ARRAY_SIZE(D_LEVEL); + +#define __debugfs_register(prefix, name, parent) \ +do { \ + result = d_level_register_debugfs(prefix, name, parent); \ + if (result < 0) \ + goto error; \ +} while (0) + + +int wimax_debugfs_add(struct wimax_dev *wimax_dev) +{ + int result; + struct net_device *net_dev = wimax_dev->net_dev; + struct device *dev = net_dev->dev.parent; + struct dentry *dentry; + char buf[128]; + + snprintf(buf, sizeof(buf), "wimax:%s", net_dev->name); + dentry = debugfs_create_dir(buf, NULL); + result = PTR_ERR(dentry); + if (IS_ERR(dentry)) { + if (result == -ENODEV) + result = 0; /* No debugfs support */ + else + dev_err(dev, "Can't create debugfs dentry: %d\n", + result); + goto out; + } + wimax_dev->debugfs_dentry = dentry; + __debugfs_register("wimax_dl_", debugfs, dentry); + __debugfs_register("wimax_dl_", id_table, dentry); + __debugfs_register("wimax_dl_", op_msg, dentry); + __debugfs_register("wimax_dl_", op_reset, dentry); + __debugfs_register("wimax_dl_", op_rfkill, dentry); + __debugfs_register("wimax_dl_", stack, dentry); + result = 0; +out: + return result; + +error: + debugfs_remove_recursive(wimax_dev->debugfs_dentry); + return result; +} + +void wimax_debugfs_rm(struct wimax_dev *wimax_dev) +{ + debugfs_remove_recursive(wimax_dev->debugfs_dentry); +} + + diff --git a/net/wimax/id-table.c b/net/wimax/id-table.c new file mode 100644 index 000000000000..d3b88558682c --- /dev/null +++ b/net/wimax/id-table.c @@ -0,0 +1,142 @@ +/* + * Linux WiMAX + * Mappping of generic netlink family IDs to net devices + * + * + * Copyright (C) 2005-2006 Intel Corporation <linux-wimax@intel.com> + * Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License version + * 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA + * 02110-1301, USA. + * + * + * We assign a single generic netlink family ID to each device (to + * simplify lookup). + * + * We need a way to map family ID to a wimax_dev pointer. + * + * The idea is to use a very simple lookup. Using a netlink attribute + * with (for example) the interface name implies a heavier search over + * all the network devices; seemed kind of a waste given that we know + * we are looking for a WiMAX device and that most systems will have + * just a single WiMAX adapter. + * + * We put all the WiMAX devices in the system in a linked list and + * match the generic link family ID against the list. + * + * By using a linked list, the case of a single adapter in the system + * becomes (almost) no overhead, while still working for many more. If + * it ever goes beyond two, I'll be surprised. + */ +#include <linux/device.h> +#include <net/genetlink.h> +#include <linux/netdevice.h> +#include <linux/list.h> +#include <linux/wimax.h> +#include "wimax-internal.h" + + +#define D_SUBMODULE id_table +#include "debug-levels.h" + + +static DEFINE_SPINLOCK(wimax_id_table_lock); +static struct list_head wimax_id_table = LIST_HEAD_INIT(wimax_id_table); + + +/* + * wimax_id_table_add - add a gennetlink familiy ID / wimax_dev mapping + * + * @wimax_dev: WiMAX device descriptor to associate to the Generic + * Netlink family ID. + * + * Look for an empty spot in the ID table; if none found, double the + * table's size and get the first spot. + */ +void wimax_id_table_add(struct wimax_dev *wimax_dev) +{ + d_fnstart(3, NULL, "(wimax_dev %p)\n", wimax_dev); + spin_lock(&wimax_id_table_lock); + list_add(&wimax_dev->id_table_node, &wimax_id_table); + spin_unlock(&wimax_id_table_lock); + d_fnend(3, NULL, "(wimax_dev %p)\n", wimax_dev); +} + + +/* + * wimax_get_netdev_by_info - lookup a wimax_dev from the gennetlink info + * + * The generic netlink family ID has been filled out in the + * nlmsghdr->nlmsg_type field, so we pull it from there, look it up in + * the mapping table and reference the wimax_dev. + * + * When done, the reference should be dropped with + * 'dev_put(wimax_dev->net_dev)'. + */ +struct wimax_dev *wimax_dev_get_by_genl_info( + struct genl_info *info, int ifindex) +{ + struct wimax_dev *wimax_dev = NULL; + + d_fnstart(3, NULL, "(info %p ifindex %d)\n", info, ifindex); + spin_lock(&wimax_id_table_lock); + list_for_each_entry(wimax_dev, &wimax_id_table, id_table_node) { + if (wimax_dev->net_dev->ifindex == ifindex) { + dev_hold(wimax_dev->net_dev); + break; + } + } + if (wimax_dev == NULL) + d_printf(1, NULL, "wimax: no devices found with ifindex %d\n", + ifindex); + spin_unlock(&wimax_id_table_lock); + d_fnend(3, NULL, "(info %p ifindex %d) = %p\n", + info, ifindex, wimax_dev); + return wimax_dev; +} + + +/* + * wimax_id_table_rm - Remove a gennetlink familiy ID / wimax_dev mapping + * + * @id: family ID to remove from the table + */ +void wimax_id_table_rm(struct wimax_dev *wimax_dev) +{ + spin_lock(&wimax_id_table_lock); + list_del_init(&wimax_dev->id_table_node); + spin_unlock(&wimax_id_table_lock); +} + + +/* + * Release the gennetlink family id / mapping table + * + * On debug, verify that the table is empty upon removal. + */ +void wimax_id_table_release(void) +{ +#ifndef CONFIG_BUG + return; +#endif + struct wimax_dev *wimax_dev; + + spin_lock(&wimax_id_table_lock); + list_for_each_entry(wimax_dev, &wimax_id_table, id_table_node) { + printk(KERN_ERR "BUG: %s wimax_dev %p ifindex %d not cleared\n", + __func__, wimax_dev, wimax_dev->net_dev->ifindex); + WARN_ON(1); + } + spin_unlock(&wimax_id_table_lock); +} diff --git a/net/wimax/op-msg.c b/net/wimax/op-msg.c new file mode 100644 index 000000000000..cb3b4ad53683 --- /dev/null +++ b/net/wimax/op-msg.c @@ -0,0 +1,421 @@ +/* + * Linux WiMAX + * Generic messaging interface between userspace and driver/device + * + * + * Copyright (C) 2007-2008 Intel Corporation <linux-wimax@intel.com> + * Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License version + * 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA + * 02110-1301, USA. + * + * + * This implements a direct communication channel between user space and + * the driver/device, by which free form messages can be sent back and + * forth. + * + * This is intended for device-specific features, vendor quirks, etc. + * + * See include/net/wimax.h + * + * GENERIC NETLINK ENCODING AND CAPACITY + * + * A destination "pipe name" is added to each message; it is up to the + * drivers to assign or use those names (if using them at all). + * + * Messages are encoded as a binary netlink attribute using nla_put() + * using type NLA_UNSPEC (as some versions of libnl still in + * deployment don't yet understand NLA_BINARY). + * + * The maximum capacity of this transport is PAGESIZE per message (so + * the actual payload will be bit smaller depending on the + * netlink/generic netlink attributes and headers). + * + * RECEPTION OF MESSAGES + * + * When a message is received from user space, it is passed verbatim + * to the driver calling wimax_dev->op_msg_from_user(). The return + * value from this function is passed back to user space as an ack + * over the generic netlink protocol. + * + * The stack doesn't do any processing or interpretation of these + * messages. + * + * SENDING MESSAGES + * + * Messages can be sent with wimax_msg(). + * + * If the message delivery needs to happen on a different context to + * that of its creation, wimax_msg_alloc() can be used to get a + * pointer to the message that can be delivered later on with + * wimax_msg_send(). + * + * ROADMAP + * + * wimax_gnl_doit_msg_from_user() Process a message from user space + * wimax_dev_get_by_genl_info() + * wimax_dev->op_msg_from_user() Delivery of message to the driver + * + * wimax_msg() Send a message to user space + * wimax_msg_alloc() + * wimax_msg_send() + */ +#include <linux/device.h> +#include <net/genetlink.h> +#include <linux/netdevice.h> +#include <linux/wimax.h> +#include <linux/security.h> +#include "wimax-internal.h" + + +#define D_SUBMODULE op_msg +#include "debug-levels.h" + + +/** + * wimax_msg_alloc - Create a new skb for sending a message to userspace + * + * @wimax_dev: WiMAX device descriptor + * @pipe_name: "named pipe" the message will be sent to + * @msg: pointer to the message data to send + * @size: size of the message to send (in bytes), including the header. + * @gfp_flags: flags for memory allocation. + * + * Returns: %0 if ok, negative errno code on error + * + * Description: + * + * Allocates an skb that will contain the message to send to user + * space over the messaging pipe and initializes it, copying the + * payload. + * + * Once this call is done, you can deliver it with + * wimax_msg_send(). + * + * IMPORTANT: + * + * Don't use skb_push()/skb_pull()/skb_reserve() on the skb, as + * wimax_msg_send() depends on skb->data being placed at the + * beginning of the user message. + */ +struct sk_buff *wimax_msg_alloc(struct wimax_dev *wimax_dev, + const char *pipe_name, + const void *msg, size_t size, + gfp_t gfp_flags) +{ + int result; + struct device *dev = wimax_dev->net_dev->dev.parent; + size_t msg_size; + void *genl_msg; + struct sk_buff *skb; + + msg_size = nla_total_size(size) + + nla_total_size(sizeof(u32)) + + (pipe_name ? nla_total_size(strlen(pipe_name)) : 0); + result = -ENOMEM; + skb = genlmsg_new(msg_size, gfp_flags); + if (skb == NULL) + goto error_new; + genl_msg = genlmsg_put(skb, 0, 0, &wimax_gnl_family, + 0, WIMAX_GNL_OP_MSG_TO_USER); + if (genl_msg == NULL) { + dev_err(dev, "no memory to create generic netlink message\n"); + goto error_genlmsg_put; + } + result = nla_put_u32(skb, WIMAX_GNL_MSG_IFIDX, + wimax_dev->net_dev->ifindex); + if (result < 0) { + dev_err(dev, "no memory to add ifindex attribute\n"); + goto error_nla_put; + } + if (pipe_name) { + result = nla_put_string(skb, WIMAX_GNL_MSG_PIPE_NAME, + pipe_name); + if (result < 0) { + dev_err(dev, "no memory to add pipe_name attribute\n"); + goto error_nla_put; + } + } + result = nla_put(skb, WIMAX_GNL_MSG_DATA, size, msg); + if (result < 0) { + dev_err(dev, "no memory to add payload in attribute\n"); + goto error_nla_put; + } + genlmsg_end(skb, genl_msg); + return skb; + +error_nla_put: +error_genlmsg_put: +error_new: + nlmsg_free(skb); + return ERR_PTR(result); + +} +EXPORT_SYMBOL_GPL(wimax_msg_alloc); + + +/** + * wimax_msg_data_len - Return a pointer and size of a message's payload + * + * @msg: Pointer to a message created with wimax_msg_alloc() + * @size: Pointer to where to store the message's size + * + * Returns the pointer to the message data. + */ +const void *wimax_msg_data_len(struct sk_buff *msg, size_t *size) +{ + struct nlmsghdr *nlh = (void *) msg->head; + struct nlattr *nla; + + nla = nlmsg_find_attr(nlh, sizeof(struct genlmsghdr), + WIMAX_GNL_MSG_DATA); + if (nla == NULL) { + printk(KERN_ERR "Cannot find attribute WIMAX_GNL_MSG_DATA\n"); + return NULL; + } + *size = nla_len(nla); + return nla_data(nla); +} +EXPORT_SYMBOL_GPL(wimax_msg_data_len); + + +/** + * wimax_msg_data - Return a pointer to a message's payload + * + * @msg: Pointer to a message created with wimax_msg_alloc() + */ +const void *wimax_msg_data(struct sk_buff *msg) +{ + struct nlmsghdr *nlh = (void *) msg->head; + struct nlattr *nla; + + nla = nlmsg_find_attr(nlh, sizeof(struct genlmsghdr), + WIMAX_GNL_MSG_DATA); + if (nla == NULL) { + printk(KERN_ERR "Cannot find attribute WIMAX_GNL_MSG_DATA\n"); + return NULL; + } + return nla_data(nla); +} +EXPORT_SYMBOL_GPL(wimax_msg_data); + + +/** + * wimax_msg_len - Return a message's payload length + * + * @msg: Pointer to a message created with wimax_msg_alloc() + */ +ssize_t wimax_msg_len(struct sk_buff *msg) +{ + struct nlmsghdr *nlh = (void *) msg->head; + struct nlattr *nla; + + nla = nlmsg_find_attr(nlh, sizeof(struct genlmsghdr), + WIMAX_GNL_MSG_DATA); + if (nla == NULL) { + printk(KERN_ERR "Cannot find attribute WIMAX_GNL_MSG_DATA\n"); + return -EINVAL; + } + return nla_len(nla); +} +EXPORT_SYMBOL_GPL(wimax_msg_len); + + +/** + * wimax_msg_send - Send a pre-allocated message to user space + * + * @wimax_dev: WiMAX device descriptor + * + * @skb: &struct sk_buff returned by wimax_msg_alloc(). Note the + * ownership of @skb is transferred to this function. + * + * Returns: 0 if ok, < 0 errno code on error + * + * Description: + * + * Sends a free-form message that was preallocated with + * wimax_msg_alloc() and filled up. + * + * Assumes that once you pass an skb to this function for sending, it + * owns it and will release it when done (on success). + * + * IMPORTANT: + * + * Don't use skb_push()/skb_pull()/skb_reserve() on the skb, as + * wimax_msg_send() depends on skb->data being placed at the + * beginning of the user message. + */ +int wimax_msg_send(struct wimax_dev *wimax_dev, struct sk_buff *skb) +{ + int result; + struct device *dev = wimax_dev->net_dev->dev.parent; + void *msg = skb->data; + size_t size = skb->len; + might_sleep(); + + d_printf(1, dev, "CTX: wimax msg, %zu bytes\n", size); + d_dump(2, dev, msg, size); + result = genlmsg_multicast(skb, 0, wimax_gnl_mcg.id, GFP_KERNEL); + d_printf(1, dev, "CTX: genl multicast result %d\n", result); + if (result == -ESRCH) /* Nobody connected, ignore it */ + result = 0; /* btw, the skb is freed already */ + return result; +} +EXPORT_SYMBOL_GPL(wimax_msg_send); + + +/** + * wimax_msg - Send a message to user space + * + * @wimax_dev: WiMAX device descriptor (properly referenced) + * @pipe_name: "named pipe" the message will be sent to + * @buf: pointer to the message to send. + * @size: size of the buffer pointed to by @buf (in bytes). + * @gfp_flags: flags for memory allocation. + * + * Returns: %0 if ok, negative errno code on error. + * + * Description: + * + * Sends a free-form message to user space on the device @wimax_dev. + * + * NOTES: + * + * Once the @skb is given to this function, who will own it and will + * release it when done (unless it returns error). + */ +int wimax_msg(struct wimax_dev *wimax_dev, const char *pipe_name, + const void *buf, size_t size, gfp_t gfp_flags) +{ + int result = -ENOMEM; + struct sk_buff *skb; + + skb = wimax_msg_alloc(wimax_dev, pipe_name, buf, size, gfp_flags); + if (skb == NULL) + goto error_msg_new; + result = wimax_msg_send(wimax_dev, skb); +error_msg_new: + return result; +} +EXPORT_SYMBOL_GPL(wimax_msg); + + +static const +struct nla_policy wimax_gnl_msg_policy[WIMAX_GNL_ATTR_MAX + 1] = { + [WIMAX_GNL_MSG_IFIDX] = { + .type = NLA_U32, + }, + [WIMAX_GNL_MSG_DATA] = { + .type = NLA_UNSPEC, /* libnl doesn't grok BINARY yet */ + }, +}; + + +/* + * Relays a message from user space to the driver + * + * The skb is passed to the driver-specific function with the netlink + * and generic netlink headers already stripped. + * + * This call will block while handling/relaying the message. + */ +static +int wimax_gnl_doit_msg_from_user(struct sk_buff *skb, struct genl_info *info) +{ + int result, ifindex; + struct wimax_dev *wimax_dev; + struct device *dev; + struct nlmsghdr *nlh = info->nlhdr; + char *pipe_name; + void *msg_buf; + size_t msg_len; + + might_sleep(); + d_fnstart(3, NULL, "(skb %p info %p)\n", skb, info); + result = -ENODEV; + if (info->attrs[WIMAX_GNL_MSG_IFIDX] == NULL) { + printk(KERN_ERR "WIMAX_GNL_MSG_FROM_USER: can't find IFIDX " + "attribute\n"); + goto error_no_wimax_dev; + } + ifindex = nla_get_u32(info->attrs[WIMAX_GNL_MSG_IFIDX]); + wimax_dev = wimax_dev_get_by_genl_info(info, ifindex); + if (wimax_dev == NULL) + goto error_no_wimax_dev; + dev = wimax_dev_to_dev(wimax_dev); + + /* Unpack arguments */ + result = -EINVAL; + if (info->attrs[WIMAX_GNL_MSG_DATA] == NULL) { + dev_err(dev, "WIMAX_GNL_MSG_FROM_USER: can't find MSG_DATA " + "attribute\n"); + goto error_no_data; + } + msg_buf = nla_data(info->attrs[WIMAX_GNL_MSG_DATA]); + msg_len = nla_len(info->attrs[WIMAX_GNL_MSG_DATA]); + + if (info->attrs[WIMAX_GNL_MSG_PIPE_NAME] == NULL) + pipe_name = NULL; + else { + struct nlattr *attr = info->attrs[WIMAX_GNL_MSG_PIPE_NAME]; + size_t attr_len = nla_len(attr); + /* libnl-1.1 does not yet support NLA_NUL_STRING */ + result = -ENOMEM; + pipe_name = kstrndup(nla_data(attr), attr_len + 1, GFP_KERNEL); + if (pipe_name == NULL) + goto error_alloc; + pipe_name[attr_len] = 0; + } + mutex_lock(&wimax_dev->mutex); + result = wimax_dev_is_ready(wimax_dev); + if (result < 0) + goto error_not_ready; + result = -ENOSYS; + if (wimax_dev->op_msg_from_user == NULL) + goto error_noop; + + d_printf(1, dev, + "CRX: nlmsghdr len %u type %u flags 0x%04x seq 0x%x pid %u\n", + nlh->nlmsg_len, nlh->nlmsg_type, nlh->nlmsg_flags, + nlh->nlmsg_seq, nlh->nlmsg_pid); + d_printf(1, dev, "CRX: wimax message %zu bytes\n", msg_len); + d_dump(2, dev, msg_buf, msg_len); + + result = wimax_dev->op_msg_from_user(wimax_dev, pipe_name, + msg_buf, msg_len, info); +error_noop: +error_not_ready: + mutex_unlock(&wimax_dev->mutex); +error_alloc: + kfree(pipe_name); +error_no_data: + dev_put(wimax_dev->net_dev); +error_no_wimax_dev: + d_fnend(3, NULL, "(skb %p info %p) = %d\n", skb, info, result); + return result; +} + + +/* + * Generic Netlink glue + */ + +struct genl_ops wimax_gnl_msg_from_user = { + .cmd = WIMAX_GNL_OP_MSG_FROM_USER, + .flags = GENL_ADMIN_PERM, + .policy = wimax_gnl_msg_policy, + .doit = wimax_gnl_doit_msg_from_user, + .dumpit = NULL, +}; + diff --git a/net/wimax/op-reset.c b/net/wimax/op-reset.c new file mode 100644 index 000000000000..ca269178c4d4 --- /dev/null +++ b/net/wimax/op-reset.c @@ -0,0 +1,143 @@ +/* + * Linux WiMAX + * Implement and export a method for resetting a WiMAX device + * + * + * Copyright (C) 2008 Intel Corporation <linux-wimax@intel.com> + * Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License version + * 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA + * 02110-1301, USA. + * + * + * This implements a simple synchronous call to reset a WiMAX device. + * + * Resets aim at being warm, keeping the device handles active; + * however, when that fails, it falls back to a cold reset (that will + * disconnect and reconnect the device). + */ + +#include <net/wimax.h> +#include <net/genetlink.h> +#include <linux/wimax.h> +#include <linux/security.h> +#include "wimax-internal.h" + +#define D_SUBMODULE op_reset +#include "debug-levels.h" + + +/** + * wimax_reset - Reset a WiMAX device + * + * @wimax_dev: WiMAX device descriptor + * + * Returns: + * + * %0 if ok and a warm reset was done (the device still exists in + * the system). + * + * -%ENODEV if a cold/bus reset had to be done (device has + * disconnected and reconnected, so current handle is not valid + * any more). + * + * -%EINVAL if the device is not even registered. + * + * Any other negative error code shall be considered as + * non-recoverable. + * + * Description: + * + * Called when wanting to reset the device for any reason. Device is + * taken back to power on status. + * + * This call blocks; on succesful return, the device has completed the + * reset process and is ready to operate. + */ +int wimax_reset(struct wimax_dev *wimax_dev) +{ + int result = -EINVAL; + struct device *dev = wimax_dev_to_dev(wimax_dev); + enum wimax_st state; + + might_sleep(); + d_fnstart(3, dev, "(wimax_dev %p)\n", wimax_dev); + mutex_lock(&wimax_dev->mutex); + dev_hold(wimax_dev->net_dev); + state = wimax_dev->state; + mutex_unlock(&wimax_dev->mutex); + + if (state >= WIMAX_ST_DOWN) { + mutex_lock(&wimax_dev->mutex_reset); + result = wimax_dev->op_reset(wimax_dev); + mutex_unlock(&wimax_dev->mutex_reset); + } + dev_put(wimax_dev->net_dev); + + d_fnend(3, dev, "(wimax_dev %p) = %d\n", wimax_dev, result); + return result; +} +EXPORT_SYMBOL(wimax_reset); + + +static const +struct nla_policy wimax_gnl_reset_policy[WIMAX_GNL_ATTR_MAX + 1] = { + [WIMAX_GNL_RESET_IFIDX] = { + .type = NLA_U32, + }, +}; + + +/* + * Exporting to user space over generic netlink + * + * Parse the reset command from user space, return error code. + * + * No attributes. + */ +static +int wimax_gnl_doit_reset(struct sk_buff *skb, struct genl_info *info) +{ + int result, ifindex; + struct wimax_dev *wimax_dev; + struct device *dev; + + d_fnstart(3, NULL, "(skb %p info %p)\n", skb, info); + result = -ENODEV; + if (info->attrs[WIMAX_GNL_RESET_IFIDX] == NULL) { + printk(KERN_ERR "WIMAX_GNL_OP_RFKILL: can't find IFIDX " + "attribute\n"); + goto error_no_wimax_dev; + } + ifindex = nla_get_u32(info->attrs[WIMAX_GNL_RESET_IFIDX]); + wimax_dev = wimax_dev_get_by_genl_info(info, ifindex); + if (wimax_dev == NULL) + goto error_no_wimax_dev; + dev = wimax_dev_to_dev(wimax_dev); + /* Execute the operation and send the result back to user space */ + result = wimax_reset(wimax_dev); + dev_put(wimax_dev->net_dev); +error_no_wimax_dev: + d_fnend(3, NULL, "(skb %p info %p) = %d\n", skb, info, result); + return result; +} + + +struct genl_ops wimax_gnl_reset = { + .cmd = WIMAX_GNL_OP_RESET, + .flags = GENL_ADMIN_PERM, + .policy = wimax_gnl_reset_policy, + .doit = wimax_gnl_doit_reset, + .dumpit = NULL, +}; diff --git a/net/wimax/op-rfkill.c b/net/wimax/op-rfkill.c new file mode 100644 index 000000000000..8745bac173f1 --- /dev/null +++ b/net/wimax/op-rfkill.c @@ -0,0 +1,532 @@ +/* + * Linux WiMAX + * RF-kill framework integration + * + * + * Copyright (C) 2008 Intel Corporation <linux-wimax@intel.com> + * Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License version + * 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA + * 02110-1301, USA. + * + * + * This integrates into the Linux Kernel rfkill susbystem so that the + * drivers just have to do the bare minimal work, which is providing a + * method to set the software RF-Kill switch and to report changes in + * the software and hardware switch status. + * + * A non-polled generic rfkill device is embedded into the WiMAX + * subsystem's representation of a device. + * + * FIXME: Need polled support? use a timer or add the implementation + * to the stack. + * + * All device drivers have to do is after wimax_dev_init(), call + * wimax_report_rfkill_hw() and wimax_report_rfkill_sw() to update + * initial state and then every time it changes. See wimax.h:struct + * wimax_dev for more information. + * + * ROADMAP + * + * wimax_gnl_doit_rfkill() User space calling wimax_rfkill() + * wimax_rfkill() Kernel calling wimax_rfkill() + * __wimax_rf_toggle_radio() + * + * wimax_rfkill_toggle_radio() RF-Kill subsytem calling + * __wimax_rf_toggle_radio() + * + * __wimax_rf_toggle_radio() + * wimax_dev->op_rfkill_sw_toggle() Driver backend + * __wimax_state_change() + * + * wimax_report_rfkill_sw() Driver reports state change + * __wimax_state_change() + * + * wimax_report_rfkill_hw() Driver reports state change + * __wimax_state_change() + * + * wimax_rfkill_add() Initialize/shutdown rfkill support + * wimax_rfkill_rm() [called by wimax_dev_add/rm()] + */ + +#include <net/wimax.h> +#include <net/genetlink.h> +#include <linux/wimax.h> +#include <linux/security.h> +#include <linux/rfkill.h> +#include <linux/input.h> +#include "wimax-internal.h" + +#define D_SUBMODULE op_rfkill +#include "debug-levels.h" + +#ifdef CONFIG_RFKILL + + +/** + * wimax_report_rfkill_hw - Reports changes in the hardware RF switch + * + * @wimax_dev: WiMAX device descriptor + * + * @state: New state of the RF Kill switch. %WIMAX_RF_ON radio on, + * %WIMAX_RF_OFF radio off. + * + * When the device detects a change in the state of thehardware RF + * switch, it must call this function to let the WiMAX kernel stack + * know that the state has changed so it can be properly propagated. + * + * The WiMAX stack caches the state (the driver doesn't need to). As + * well, as the change is propagated it will come back as a request to + * change the software state to mirror the hardware state. + * + * If the device doesn't have a hardware kill switch, just report + * it on initialization as always on (%WIMAX_RF_ON, radio on). + */ +void wimax_report_rfkill_hw(struct wimax_dev *wimax_dev, + enum wimax_rf_state state) +{ + int result; + struct device *dev = wimax_dev_to_dev(wimax_dev); + enum wimax_st wimax_state; + enum rfkill_state rfkill_state; + + d_fnstart(3, dev, "(wimax_dev %p state %u)\n", wimax_dev, state); + BUG_ON(state == WIMAX_RF_QUERY); + BUG_ON(state != WIMAX_RF_ON && state != WIMAX_RF_OFF); + + mutex_lock(&wimax_dev->mutex); + result = wimax_dev_is_ready(wimax_dev); + if (result < 0) + goto error_not_ready; + + if (state != wimax_dev->rf_hw) { + wimax_dev->rf_hw = state; + rfkill_state = state == WIMAX_RF_ON ? + RFKILL_STATE_OFF : RFKILL_STATE_ON; + if (wimax_dev->rf_hw == WIMAX_RF_ON + && wimax_dev->rf_sw == WIMAX_RF_ON) + wimax_state = WIMAX_ST_READY; + else + wimax_state = WIMAX_ST_RADIO_OFF; + __wimax_state_change(wimax_dev, wimax_state); + input_report_key(wimax_dev->rfkill_input, KEY_WIMAX, + rfkill_state); + } +error_not_ready: + mutex_unlock(&wimax_dev->mutex); + d_fnend(3, dev, "(wimax_dev %p state %u) = void [%d]\n", + wimax_dev, state, result); +} +EXPORT_SYMBOL_GPL(wimax_report_rfkill_hw); + + +/** + * wimax_report_rfkill_sw - Reports changes in the software RF switch + * + * @wimax_dev: WiMAX device descriptor + * + * @state: New state of the RF kill switch. %WIMAX_RF_ON radio on, + * %WIMAX_RF_OFF radio off. + * + * Reports changes in the software RF switch state to the the WiMAX + * stack. + * + * The main use is during initialization, so the driver can query the + * device for its current software radio kill switch state and feed it + * to the system. + * + * On the side, the device does not change the software state by + * itself. In practice, this can happen, as the device might decide to + * switch (in software) the radio off for different reasons. + */ +void wimax_report_rfkill_sw(struct wimax_dev *wimax_dev, + enum wimax_rf_state state) +{ + int result; + struct device *dev = wimax_dev_to_dev(wimax_dev); + enum wimax_st wimax_state; + + d_fnstart(3, dev, "(wimax_dev %p state %u)\n", wimax_dev, state); + BUG_ON(state == WIMAX_RF_QUERY); + BUG_ON(state != WIMAX_RF_ON && state != WIMAX_RF_OFF); + + mutex_lock(&wimax_dev->mutex); + result = wimax_dev_is_ready(wimax_dev); + if (result < 0) + goto error_not_ready; + + if (state != wimax_dev->rf_sw) { + wimax_dev->rf_sw = state; + if (wimax_dev->rf_hw == WIMAX_RF_ON + && wimax_dev->rf_sw == WIMAX_RF_ON) + wimax_state = WIMAX_ST_READY; + else + wimax_state = WIMAX_ST_RADIO_OFF; + __wimax_state_change(wimax_dev, wimax_state); + } +error_not_ready: + mutex_unlock(&wimax_dev->mutex); + d_fnend(3, dev, "(wimax_dev %p state %u) = void [%d]\n", + wimax_dev, state, result); +} +EXPORT_SYMBOL_GPL(wimax_report_rfkill_sw); + + +/* + * Callback for the RF Kill toggle operation + * + * This function is called by: + * + * - The rfkill subsystem when the RF-Kill key is pressed in the + * hardware and the driver notifies through + * wimax_report_rfkill_hw(). The rfkill subsystem ends up calling back + * here so the software RF Kill switch state is changed to reflect + * the hardware switch state. + * + * - When the user sets the state through sysfs' rfkill/state file + * + * - When the user calls wimax_rfkill(). + * + * This call blocks! + * + * WARNING! When we call rfkill_unregister(), this will be called with + * state 0! + * + * WARNING: wimax_dev must be locked + */ +static +int __wimax_rf_toggle_radio(struct wimax_dev *wimax_dev, + enum wimax_rf_state state) +{ + int result = 0; + struct device *dev = wimax_dev_to_dev(wimax_dev); + enum wimax_st wimax_state; + + might_sleep(); + d_fnstart(3, dev, "(wimax_dev %p state %u)\n", wimax_dev, state); + if (wimax_dev->rf_sw == state) + goto out_no_change; + if (wimax_dev->op_rfkill_sw_toggle != NULL) + result = wimax_dev->op_rfkill_sw_toggle(wimax_dev, state); + else if (state == WIMAX_RF_OFF) /* No op? can't turn off */ + result = -ENXIO; + else /* No op? can turn on */ + result = 0; /* should never happen tho */ + if (result >= 0) { + result = 0; + wimax_dev->rf_sw = state; + wimax_state = state == WIMAX_RF_ON ? + WIMAX_ST_READY : WIMAX_ST_RADIO_OFF; + __wimax_state_change(wimax_dev, wimax_state); + } +out_no_change: + d_fnend(3, dev, "(wimax_dev %p state %u) = %d\n", + wimax_dev, state, result); + return result; +} + + +/* + * Translate from rfkill state to wimax state + * + * NOTE: Special state handling rules here + * + * Just pretend the call didn't happen if we are in a state where + * we know for sure it cannot be handled (WIMAX_ST_DOWN or + * __WIMAX_ST_QUIESCING). rfkill() needs it to register and + * unregister, as it will run this path. + * + * NOTE: This call will block until the operation is completed. + */ +static +int wimax_rfkill_toggle_radio(void *data, enum rfkill_state state) +{ + int result; + struct wimax_dev *wimax_dev = data; + struct device *dev = wimax_dev_to_dev(wimax_dev); + enum wimax_rf_state rf_state; + + d_fnstart(3, dev, "(wimax_dev %p state %u)\n", wimax_dev, state); + switch (state) { + case RFKILL_STATE_ON: + rf_state = WIMAX_RF_OFF; + break; + case RFKILL_STATE_OFF: + rf_state = WIMAX_RF_ON; + break; + default: + BUG(); + } + mutex_lock(&wimax_dev->mutex); + if (wimax_dev->state <= __WIMAX_ST_QUIESCING) + result = 0; /* just pretend it didn't happen */ + else + result = __wimax_rf_toggle_radio(wimax_dev, rf_state); + mutex_unlock(&wimax_dev->mutex); + d_fnend(3, dev, "(wimax_dev %p state %u) = %d\n", + wimax_dev, state, result); + return result; +} + + +/** + * wimax_rfkill - Set the software RF switch state for a WiMAX device + * + * @wimax_dev: WiMAX device descriptor + * + * @state: New RF state. + * + * Returns: + * + * >= 0 toggle state if ok, < 0 errno code on error. The toggle state + * is returned as a bitmap, bit 0 being the hardware RF state, bit 1 + * the software RF state. + * + * 0 means disabled (%WIMAX_RF_ON, radio on), 1 means enabled radio + * off (%WIMAX_RF_OFF). + * + * Description: + * + * Called by the user when he wants to request the WiMAX radio to be + * switched on (%WIMAX_RF_ON) or off (%WIMAX_RF_OFF). With + * %WIMAX_RF_QUERY, just the current state is returned. + * + * NOTE: + * + * This call will block until the operation is complete. + */ +int wimax_rfkill(struct wimax_dev *wimax_dev, enum wimax_rf_state state) +{ + int result; + struct device *dev = wimax_dev_to_dev(wimax_dev); + + d_fnstart(3, dev, "(wimax_dev %p state %u)\n", wimax_dev, state); + mutex_lock(&wimax_dev->mutex); + result = wimax_dev_is_ready(wimax_dev); + if (result < 0) + goto error_not_ready; + switch (state) { + case WIMAX_RF_ON: + case WIMAX_RF_OFF: + result = __wimax_rf_toggle_radio(wimax_dev, state); + if (result < 0) + goto error; + break; + case WIMAX_RF_QUERY: + break; + default: + result = -EINVAL; + goto error; + } + result = wimax_dev->rf_sw << 1 | wimax_dev->rf_hw; +error: +error_not_ready: + mutex_unlock(&wimax_dev->mutex); + d_fnend(3, dev, "(wimax_dev %p state %u) = %d\n", + wimax_dev, state, result); + return result; +} +EXPORT_SYMBOL(wimax_rfkill); + + +/* + * Register a new WiMAX device's RF Kill support + * + * WARNING: wimax_dev->mutex must be unlocked + */ +int wimax_rfkill_add(struct wimax_dev *wimax_dev) +{ + int result; + struct rfkill *rfkill; + struct input_dev *input_dev; + struct device *dev = wimax_dev_to_dev(wimax_dev); + + d_fnstart(3, dev, "(wimax_dev %p)\n", wimax_dev); + /* Initialize RF Kill */ + result = -ENOMEM; + rfkill = rfkill_allocate(dev, RFKILL_TYPE_WIMAX); + if (rfkill == NULL) + goto error_rfkill_allocate; + wimax_dev->rfkill = rfkill; + + rfkill->name = wimax_dev->name; + rfkill->state = RFKILL_STATE_OFF; + rfkill->data = wimax_dev; + rfkill->toggle_radio = wimax_rfkill_toggle_radio; + rfkill->user_claim_unsupported = 1; + + /* Initialize the input device for the hw key */ + input_dev = input_allocate_device(); + if (input_dev == NULL) + goto error_input_allocate; + wimax_dev->rfkill_input = input_dev; + d_printf(1, dev, "rfkill %p input %p\n", rfkill, input_dev); + + input_dev->name = wimax_dev->name; + /* FIXME: get a real device bus ID and stuff? do we care? */ + input_dev->id.bustype = BUS_HOST; + input_dev->id.vendor = 0xffff; + input_dev->evbit[0] = BIT(EV_KEY); + set_bit(KEY_WIMAX, input_dev->keybit); + + /* Register both */ + result = input_register_device(wimax_dev->rfkill_input); + if (result < 0) + goto error_input_register; + result = rfkill_register(wimax_dev->rfkill); + if (result < 0) + goto error_rfkill_register; + + /* If there is no SW toggle op, SW RFKill is always on */ + if (wimax_dev->op_rfkill_sw_toggle == NULL) + wimax_dev->rf_sw = WIMAX_RF_ON; + + d_fnend(3, dev, "(wimax_dev %p) = 0\n", wimax_dev); + return 0; + + /* if rfkill_register() suceeds, can't use rfkill_free() any + * more, only rfkill_unregister() [it owns the refcount]; with + * the input device we have the same issue--hence the if. */ +error_rfkill_register: + input_unregister_device(wimax_dev->rfkill_input); + wimax_dev->rfkill_input = NULL; +error_input_register: + if (wimax_dev->rfkill_input) + input_free_device(wimax_dev->rfkill_input); +error_input_allocate: + rfkill_free(wimax_dev->rfkill); +error_rfkill_allocate: + d_fnend(3, dev, "(wimax_dev %p) = %d\n", wimax_dev, result); + return result; +} + + +/* + * Deregister a WiMAX device's RF Kill support + * + * Ick, we can't call rfkill_free() after rfkill_unregister()...oh + * well. + * + * WARNING: wimax_dev->mutex must be unlocked + */ +void wimax_rfkill_rm(struct wimax_dev *wimax_dev) +{ + struct device *dev = wimax_dev_to_dev(wimax_dev); + d_fnstart(3, dev, "(wimax_dev %p)\n", wimax_dev); + rfkill_unregister(wimax_dev->rfkill); /* frees */ + input_unregister_device(wimax_dev->rfkill_input); + d_fnend(3, dev, "(wimax_dev %p)\n", wimax_dev); +} + + +#else /* #ifdef CONFIG_RFKILL */ + +void wimax_report_rfkill_hw(struct wimax_dev *wimax_dev, + enum wimax_rf_state state) +{ +} +EXPORT_SYMBOL_GPL(wimax_report_rfkill_hw); + +void wimax_report_rfkill_sw(struct wimax_dev *wimax_dev, + enum wimax_rf_state state) +{ +} +EXPORT_SYMBOL_GPL(wimax_report_rfkill_sw); + +int wimax_rfkill(struct wimax_dev *wimax_dev, + enum wimax_rf_state state) +{ + return WIMAX_RF_ON << 1 | WIMAX_RF_ON; +} +EXPORT_SYMBOL_GPL(wimax_rfkill); + +int wimax_rfkill_add(struct wimax_dev *wimax_dev) +{ + return 0; +} + +void wimax_rfkill_rm(struct wimax_dev *wimax_dev) +{ +} + +#endif /* #ifdef CONFIG_RFKILL */ + + +/* + * Exporting to user space over generic netlink + * + * Parse the rfkill command from user space, return a combination + * value that describe the states of the different toggles. + * + * Only one attribute: the new state requested (on, off or no change, + * just query). + */ + +static const +struct nla_policy wimax_gnl_rfkill_policy[WIMAX_GNL_ATTR_MAX + 1] = { + [WIMAX_GNL_RFKILL_IFIDX] = { + .type = NLA_U32, + }, + [WIMAX_GNL_RFKILL_STATE] = { + .type = NLA_U32 /* enum wimax_rf_state */ + }, +}; + + +static +int wimax_gnl_doit_rfkill(struct sk_buff *skb, struct genl_info *info) +{ + int result, ifindex; + struct wimax_dev *wimax_dev; + struct device *dev; + enum wimax_rf_state new_state; + + d_fnstart(3, NULL, "(skb %p info %p)\n", skb, info); + result = -ENODEV; + if (info->attrs[WIMAX_GNL_RFKILL_IFIDX] == NULL) { + printk(KERN_ERR "WIMAX_GNL_OP_RFKILL: can't find IFIDX " + "attribute\n"); + goto error_no_wimax_dev; + } + ifindex = nla_get_u32(info->attrs[WIMAX_GNL_RFKILL_IFIDX]); + wimax_dev = wimax_dev_get_by_genl_info(info, ifindex); + if (wimax_dev == NULL) + goto error_no_wimax_dev; + dev = wimax_dev_to_dev(wimax_dev); + result = -EINVAL; + if (info->attrs[WIMAX_GNL_RFKILL_STATE] == NULL) { + dev_err(dev, "WIMAX_GNL_RFKILL: can't find RFKILL_STATE " + "attribute\n"); + goto error_no_pid; + } + new_state = nla_get_u32(info->attrs[WIMAX_GNL_RFKILL_STATE]); + + /* Execute the operation and send the result back to user space */ + result = wimax_rfkill(wimax_dev, new_state); +error_no_pid: + dev_put(wimax_dev->net_dev); +error_no_wimax_dev: + d_fnend(3, NULL, "(skb %p info %p) = %d\n", skb, info, result); + return result; +} + + +struct genl_ops wimax_gnl_rfkill = { + .cmd = WIMAX_GNL_OP_RFKILL, + .flags = GENL_ADMIN_PERM, + .policy = wimax_gnl_rfkill_policy, + .doit = wimax_gnl_doit_rfkill, + .dumpit = NULL, +}; + diff --git a/net/wimax/stack.c b/net/wimax/stack.c new file mode 100644 index 000000000000..d4da92f8981a --- /dev/null +++ b/net/wimax/stack.c @@ -0,0 +1,599 @@ +/* + * Linux WiMAX + * Initialization, addition and removal of wimax devices + * + * + * Copyright (C) 2005-2006 Intel Corporation <linux-wimax@intel.com> + * Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License version + * 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA + * 02110-1301, USA. + * + * + * This implements: + * + * - basic life cycle of 'struct wimax_dev' [wimax_dev_*()]; on + * addition/registration initialize all subfields and allocate + * generic netlink resources for user space communication. On + * removal/unregistration, undo all that. + * + * - device state machine [wimax_state_change()] and support to send + * reports to user space when the state changes + * [wimax_gnl_re_state_change*()]. + * + * See include/net/wimax.h for rationales and design. + * + * ROADMAP + * + * [__]wimax_state_change() Called by drivers to update device's state + * wimax_gnl_re_state_change_alloc() + * wimax_gnl_re_state_change_send() + * + * wimax_dev_init() Init a device + * wimax_dev_add() Register + * wimax_rfkill_add() + * wimax_gnl_add() Register all the generic netlink resources. + * wimax_id_table_add() + * wimax_dev_rm() Unregister + * wimax_id_table_rm() + * wimax_gnl_rm() + * wimax_rfkill_rm() + */ +#include <linux/device.h> +#include <net/genetlink.h> +#include <linux/netdevice.h> +#include <linux/wimax.h> +#include "wimax-internal.h" + + +#define D_SUBMODULE stack +#include "debug-levels.h" + +/* + * Authoritative source for the RE_STATE_CHANGE attribute policy + * + * We don't really use it here, but /me likes to keep the definition + * close to where the data is generated. + */ +/* +static const +struct nla_policy wimax_gnl_re_status_change[WIMAX_GNL_ATTR_MAX + 1] = { + [WIMAX_GNL_STCH_STATE_OLD] = { .type = NLA_U8 }, + [WIMAX_GNL_STCH_STATE_NEW] = { .type = NLA_U8 }, +}; +*/ + + +/* + * Allocate a Report State Change message + * + * @header: save it, you need it for _send() + * + * Creates and fills a basic state change message; different code + * paths can then add more attributes to the message as needed. + * + * Use wimax_gnl_re_state_change_send() to send the returned skb. + * + * Returns: skb with the genl message if ok, IS_ERR() ptr on error + * with an errno code. + */ +static +struct sk_buff *wimax_gnl_re_state_change_alloc( + struct wimax_dev *wimax_dev, + enum wimax_st new_state, enum wimax_st old_state, + void **header) +{ + int result; + struct device *dev = wimax_dev_to_dev(wimax_dev); + void *data; + struct sk_buff *report_skb; + + d_fnstart(3, dev, "(wimax_dev %p new_state %u old_state %u)\n", + wimax_dev, new_state, old_state); + result = -ENOMEM; + report_skb = nlmsg_new(NLMSG_DEFAULT_SIZE, GFP_KERNEL); + if (report_skb == NULL) { + dev_err(dev, "RE_STCH: can't create message\n"); + goto error_new; + } + data = genlmsg_put(report_skb, 0, wimax_gnl_mcg.id, &wimax_gnl_family, + 0, WIMAX_GNL_RE_STATE_CHANGE); + if (data == NULL) { + dev_err(dev, "RE_STCH: can't put data into message\n"); + goto error_put; + } + *header = data; + + result = nla_put_u8(report_skb, WIMAX_GNL_STCH_STATE_OLD, old_state); + if (result < 0) { + dev_err(dev, "RE_STCH: Error adding OLD attr: %d\n", result); + goto error_put; + } + result = nla_put_u8(report_skb, WIMAX_GNL_STCH_STATE_NEW, new_state); + if (result < 0) { + dev_err(dev, "RE_STCH: Error adding NEW attr: %d\n", result); + goto error_put; + } + result = nla_put_u32(report_skb, WIMAX_GNL_STCH_IFIDX, + wimax_dev->net_dev->ifindex); + if (result < 0) { + dev_err(dev, "RE_STCH: Error adding IFINDEX attribute\n"); + goto error_put; + } + d_fnend(3, dev, "(wimax_dev %p new_state %u old_state %u) = %p\n", + wimax_dev, new_state, old_state, report_skb); + return report_skb; + +error_put: + nlmsg_free(report_skb); +error_new: + d_fnend(3, dev, "(wimax_dev %p new_state %u old_state %u) = %d\n", + wimax_dev, new_state, old_state, result); + return ERR_PTR(result); +} + + +/* + * Send a Report State Change message (as created with _alloc). + * + * @report_skb: as returned by wimax_gnl_re_state_change_alloc() + * @header: as returned by wimax_gnl_re_state_change_alloc() + * + * Returns: 0 if ok, < 0 errno code on error. + * + * If the message is NULL, pretend it didn't happen. + */ +static +int wimax_gnl_re_state_change_send( + struct wimax_dev *wimax_dev, struct sk_buff *report_skb, + void *header) +{ + int result = 0; + struct device *dev = wimax_dev_to_dev(wimax_dev); + d_fnstart(3, dev, "(wimax_dev %p report_skb %p)\n", + wimax_dev, report_skb); + if (report_skb == NULL) + goto out; + genlmsg_end(report_skb, header); + result = genlmsg_multicast(report_skb, 0, wimax_gnl_mcg.id, GFP_KERNEL); + if (result == -ESRCH) /* Nobody connected, ignore it */ + result = 0; /* btw, the skb is freed already */ + if (result < 0) { + dev_err(dev, "RE_STCH: Error sending: %d\n", result); + nlmsg_free(report_skb); + } +out: + d_fnend(3, dev, "(wimax_dev %p report_skb %p) = %d\n", + wimax_dev, report_skb, result); + return result; +} + + +static +void __check_new_state(enum wimax_st old_state, enum wimax_st new_state, + unsigned allowed_states_bm) +{ + if (WARN_ON(((1 << new_state) & allowed_states_bm) == 0)) { + printk(KERN_ERR "SW BUG! Forbidden state change %u -> %u\n", + old_state, new_state); + } +} + + +/* + * Set the current state of a WiMAX device [unlocking version of + * wimax_state_change(). + */ +void __wimax_state_change(struct wimax_dev *wimax_dev, enum wimax_st new_state) +{ + struct device *dev = wimax_dev_to_dev(wimax_dev); + enum wimax_st old_state = wimax_dev->state; + struct sk_buff *stch_skb; + void *header; + + d_fnstart(3, dev, "(wimax_dev %p new_state %u [old %u])\n", + wimax_dev, new_state, old_state); + + if (WARN_ON(new_state >= __WIMAX_ST_INVALID)) { + dev_err(dev, "SW BUG: requesting invalid state %u\n", + new_state); + goto out; + } + if (old_state == new_state) + goto out; + header = NULL; /* gcc complains? can't grok why */ + stch_skb = wimax_gnl_re_state_change_alloc( + wimax_dev, new_state, old_state, &header); + + /* Verify the state transition and do exit-from-state actions */ + switch (old_state) { + case __WIMAX_ST_NULL: + __check_new_state(old_state, new_state, + 1 << WIMAX_ST_DOWN); + break; + case WIMAX_ST_DOWN: + __check_new_state(old_state, new_state, + 1 << __WIMAX_ST_QUIESCING + | 1 << WIMAX_ST_UNINITIALIZED + | 1 << WIMAX_ST_RADIO_OFF); + break; + case __WIMAX_ST_QUIESCING: + __check_new_state(old_state, new_state, 1 << WIMAX_ST_DOWN); + break; + case WIMAX_ST_UNINITIALIZED: + __check_new_state(old_state, new_state, + 1 << __WIMAX_ST_QUIESCING + | 1 << WIMAX_ST_RADIO_OFF); + break; + case WIMAX_ST_RADIO_OFF: + __check_new_state(old_state, new_state, + 1 << __WIMAX_ST_QUIESCING + | 1 << WIMAX_ST_READY); + break; + case WIMAX_ST_READY: + __check_new_state(old_state, new_state, + 1 << __WIMAX_ST_QUIESCING + | 1 << WIMAX_ST_RADIO_OFF + | 1 << WIMAX_ST_SCANNING + | 1 << WIMAX_ST_CONNECTING + | 1 << WIMAX_ST_CONNECTED); + break; + case WIMAX_ST_SCANNING: + __check_new_state(old_state, new_state, + 1 << __WIMAX_ST_QUIESCING + | 1 << WIMAX_ST_RADIO_OFF + | 1 << WIMAX_ST_READY + | 1 << WIMAX_ST_CONNECTING + | 1 << WIMAX_ST_CONNECTED); + break; + case WIMAX_ST_CONNECTING: + __check_new_state(old_state, new_state, + 1 << __WIMAX_ST_QUIESCING + | 1 << WIMAX_ST_RADIO_OFF + | 1 << WIMAX_ST_READY + | 1 << WIMAX_ST_SCANNING + | 1 << WIMAX_ST_CONNECTED); + break; + case WIMAX_ST_CONNECTED: + __check_new_state(old_state, new_state, + 1 << __WIMAX_ST_QUIESCING + | 1 << WIMAX_ST_RADIO_OFF + | 1 << WIMAX_ST_READY); + netif_tx_disable(wimax_dev->net_dev); + netif_carrier_off(wimax_dev->net_dev); + break; + case __WIMAX_ST_INVALID: + default: + dev_err(dev, "SW BUG: wimax_dev %p is in unknown state %u\n", + wimax_dev, wimax_dev->state); + WARN_ON(1); + goto out; + } + + /* Execute the actions of entry to the new state */ + switch (new_state) { + case __WIMAX_ST_NULL: + dev_err(dev, "SW BUG: wimax_dev %p entering NULL state " + "from %u\n", wimax_dev, wimax_dev->state); + WARN_ON(1); /* Nobody can enter this state */ + break; + case WIMAX_ST_DOWN: + break; + case __WIMAX_ST_QUIESCING: + break; + case WIMAX_ST_UNINITIALIZED: + break; + case WIMAX_ST_RADIO_OFF: + break; + case WIMAX_ST_READY: + break; + case WIMAX_ST_SCANNING: + break; + case WIMAX_ST_CONNECTING: + break; + case WIMAX_ST_CONNECTED: + netif_carrier_on(wimax_dev->net_dev); + netif_wake_queue(wimax_dev->net_dev); + break; + case __WIMAX_ST_INVALID: + default: + BUG(); + } + __wimax_state_set(wimax_dev, new_state); + if (stch_skb) + wimax_gnl_re_state_change_send(wimax_dev, stch_skb, header); +out: + d_fnend(3, dev, "(wimax_dev %p new_state %u [old %u]) = void\n", + wimax_dev, new_state, old_state); + return; +} + + +/** + * wimax_state_change - Set the current state of a WiMAX device + * + * @wimax_dev: WiMAX device descriptor (properly referenced) + * @new_state: New state to switch to + * + * This implements the state changes for the wimax devices. It will + * + * - verify that the state transition is legal (for now it'll just + * print a warning if not) according to the table in + * linux/wimax.h's documentation for 'enum wimax_st'. + * + * - perform the actions needed for leaving the current state and + * whichever are needed for entering the new state. + * + * - issue a report to user space indicating the new state (and an + * optional payload with information about the new state). + * + * NOTE: @wimax_dev must be locked + */ +void wimax_state_change(struct wimax_dev *wimax_dev, enum wimax_st new_state) +{ + mutex_lock(&wimax_dev->mutex); + __wimax_state_change(wimax_dev, new_state); + mutex_unlock(&wimax_dev->mutex); + return; +} +EXPORT_SYMBOL_GPL(wimax_state_change); + + +/** + * wimax_state_get() - Return the current state of a WiMAX device + * + * @wimax_dev: WiMAX device descriptor + * + * Returns: Current state of the device according to its driver. + */ +enum wimax_st wimax_state_get(struct wimax_dev *wimax_dev) +{ + enum wimax_st state; + mutex_lock(&wimax_dev->mutex); + state = wimax_dev->state; + mutex_unlock(&wimax_dev->mutex); + return state; +} +EXPORT_SYMBOL_GPL(wimax_state_get); + + +/** + * wimax_dev_init - initialize a newly allocated instance + * + * @wimax_dev: WiMAX device descriptor to initialize. + * + * Initializes fields of a freshly allocated @wimax_dev instance. This + * function assumes that after allocation, the memory occupied by + * @wimax_dev was zeroed. + */ +void wimax_dev_init(struct wimax_dev *wimax_dev) +{ + INIT_LIST_HEAD(&wimax_dev->id_table_node); + __wimax_state_set(wimax_dev, WIMAX_ST_UNINITIALIZED); + mutex_init(&wimax_dev->mutex); + mutex_init(&wimax_dev->mutex_reset); +} +EXPORT_SYMBOL_GPL(wimax_dev_init); + +/* + * This extern is declared here because it's easier to keep track -- + * both declarations are a list of the same + */ +extern struct genl_ops + wimax_gnl_msg_from_user, + wimax_gnl_reset, + wimax_gnl_rfkill; + +static +struct genl_ops *wimax_gnl_ops[] = { + &wimax_gnl_msg_from_user, + &wimax_gnl_reset, + &wimax_gnl_rfkill, +}; + + +static +size_t wimax_addr_scnprint(char *addr_str, size_t addr_str_size, + unsigned char *addr, size_t addr_len) +{ + unsigned cnt, total; + for (total = cnt = 0; cnt < addr_len; cnt++) + total += scnprintf(addr_str + total, addr_str_size - total, + "%02x%c", addr[cnt], + cnt == addr_len - 1 ? '\0' : ':'); + return total; +} + + +/** + * wimax_dev_add - Register a new WiMAX device + * + * @wimax_dev: WiMAX device descriptor (as embedded in your @net_dev's + * priv data). You must have called wimax_dev_init() on it before. + * + * @net_dev: net device the @wimax_dev is associated with. The + * function expects SET_NETDEV_DEV() and register_netdev() were + * already called on it. + * + * Registers the new WiMAX device, sets up the user-kernel control + * interface (generic netlink) and common WiMAX infrastructure. + * + * Note that the parts that will allow interaction with user space are + * setup at the very end, when the rest is in place, as once that + * happens, the driver might get user space control requests via + * netlink or from debugfs that might translate into calls into + * wimax_dev->op_*(). + */ +int wimax_dev_add(struct wimax_dev *wimax_dev, struct net_device *net_dev) +{ + int result; + struct device *dev = net_dev->dev.parent; + char addr_str[32]; + + d_fnstart(3, dev, "(wimax_dev %p net_dev %p)\n", wimax_dev, net_dev); + + /* Do the RFKILL setup before locking, as RFKILL will call + * into our functions. */ + wimax_dev->net_dev = net_dev; + result = wimax_rfkill_add(wimax_dev); + if (result < 0) + goto error_rfkill_add; + + /* Set up user-space interaction */ + mutex_lock(&wimax_dev->mutex); + wimax_id_table_add(wimax_dev); + result = wimax_debugfs_add(wimax_dev); + if (result < 0) { + dev_err(dev, "cannot initialize debugfs: %d\n", + result); + goto error_debugfs_add; + } + + __wimax_state_set(wimax_dev, WIMAX_ST_DOWN); + mutex_unlock(&wimax_dev->mutex); + + wimax_addr_scnprint(addr_str, sizeof(addr_str), + net_dev->dev_addr, net_dev->addr_len); + dev_err(dev, "WiMAX interface %s (%s) ready\n", + net_dev->name, addr_str); + d_fnend(3, dev, "(wimax_dev %p net_dev %p) = 0\n", wimax_dev, net_dev); + return 0; + +error_debugfs_add: + wimax_id_table_rm(wimax_dev); + mutex_unlock(&wimax_dev->mutex); + wimax_rfkill_rm(wimax_dev); +error_rfkill_add: + d_fnend(3, dev, "(wimax_dev %p net_dev %p) = %d\n", + wimax_dev, net_dev, result); + return result; +} +EXPORT_SYMBOL_GPL(wimax_dev_add); + + +/** + * wimax_dev_rm - Unregister an existing WiMAX device + * + * @wimax_dev: WiMAX device descriptor + * + * Unregisters a WiMAX device previously registered for use with + * wimax_add_rm(). + * + * IMPORTANT! Must call before calling unregister_netdev(). + * + * After this function returns, you will not get any more user space + * control requests (via netlink or debugfs) and thus to wimax_dev->ops. + * + * Reentrancy control is ensured by setting the state to + * %__WIMAX_ST_QUIESCING. rfkill operations coming through + * wimax_*rfkill*() will be stopped by the quiescing state; ops coming + * from the rfkill subsystem will be stopped by the support being + * removed by wimax_rfkill_rm(). + */ +void wimax_dev_rm(struct wimax_dev *wimax_dev) +{ + d_fnstart(3, NULL, "(wimax_dev %p)\n", wimax_dev); + + mutex_lock(&wimax_dev->mutex); + __wimax_state_change(wimax_dev, __WIMAX_ST_QUIESCING); + wimax_debugfs_rm(wimax_dev); + wimax_id_table_rm(wimax_dev); + __wimax_state_change(wimax_dev, WIMAX_ST_DOWN); + mutex_unlock(&wimax_dev->mutex); + wimax_rfkill_rm(wimax_dev); + d_fnend(3, NULL, "(wimax_dev %p) = void\n", wimax_dev); +} +EXPORT_SYMBOL_GPL(wimax_dev_rm); + +struct genl_family wimax_gnl_family = { + .id = GENL_ID_GENERATE, + .name = "WiMAX", + .version = WIMAX_GNL_VERSION, + .hdrsize = 0, + .maxattr = WIMAX_GNL_ATTR_MAX, +}; + +struct genl_multicast_group wimax_gnl_mcg = { + .name = "msg", +}; + + + +/* Shutdown the wimax stack */ +static +int __init wimax_subsys_init(void) +{ + int result, cnt; + + d_fnstart(4, NULL, "()\n"); + snprintf(wimax_gnl_family.name, sizeof(wimax_gnl_family.name), + "WiMAX"); + result = genl_register_family(&wimax_gnl_family); + if (unlikely(result < 0)) { + printk(KERN_ERR "cannot register generic netlink family: %d\n", + result); + goto error_register_family; + } + + for (cnt = 0; cnt < ARRAY_SIZE(wimax_gnl_ops); cnt++) { + result = genl_register_ops(&wimax_gnl_family, + wimax_gnl_ops[cnt]); + d_printf(4, NULL, "registering generic netlink op code " + "%u: %d\n", wimax_gnl_ops[cnt]->cmd, result); + if (unlikely(result < 0)) { + printk(KERN_ERR "cannot register generic netlink op " + "code %u: %d\n", + wimax_gnl_ops[cnt]->cmd, result); + goto error_register_ops; + } + } + + result = genl_register_mc_group(&wimax_gnl_family, &wimax_gnl_mcg); + if (result < 0) + goto error_mc_group; + d_fnend(4, NULL, "() = 0\n"); + return 0; + +error_mc_group: +error_register_ops: + for (cnt--; cnt >= 0; cnt--) + genl_unregister_ops(&wimax_gnl_family, + wimax_gnl_ops[cnt]); + genl_unregister_family(&wimax_gnl_family); +error_register_family: + d_fnend(4, NULL, "() = %d\n", result); + return result; + +} +module_init(wimax_subsys_init); + + +/* Shutdown the wimax stack */ +static +void __exit wimax_subsys_exit(void) +{ + int cnt; + wimax_id_table_release(); + genl_unregister_mc_group(&wimax_gnl_family, &wimax_gnl_mcg); + for (cnt = ARRAY_SIZE(wimax_gnl_ops) - 1; cnt >= 0; cnt--) + genl_unregister_ops(&wimax_gnl_family, + wimax_gnl_ops[cnt]); + genl_unregister_family(&wimax_gnl_family); +} +module_exit(wimax_subsys_exit); + +MODULE_AUTHOR("Intel Corporation <linux-wimax@intel.com>"); +MODULE_DESCRIPTION("Linux WiMAX stack"); +MODULE_LICENSE("GPL"); + diff --git a/net/wimax/wimax-internal.h b/net/wimax/wimax-internal.h new file mode 100644 index 000000000000..1e743d214856 --- /dev/null +++ b/net/wimax/wimax-internal.h @@ -0,0 +1,91 @@ +/* + * Linux WiMAX + * Internal API for kernel space WiMAX stack + * + * + * Copyright (C) 2007 Intel Corporation <linux-wimax@intel.com> + * Inaky Perez-Gonzalez <inaky.perez-gonzalez@intel.com> + * + * This program is free software; you can redistribute it and/or + * modify it under the terms of the GNU General Public License version + * 2 as published by the Free Software Foundation. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 51 Franklin Street, Fifth Floor, Boston, MA + * 02110-1301, USA. + * + * + * This header file is for declarations and definitions internal to + * the WiMAX stack. For public APIs and documentation, see + * include/net/wimax.h and include/linux/wimax.h. + */ + +#ifndef __WIMAX_INTERNAL_H__ +#define __WIMAX_INTERNAL_H__ +#ifdef __KERNEL__ + +#include <linux/device.h> +#include <net/wimax.h> + + +/* + * Decide if a (locked) device is ready for use + * + * Before using the device structure, it must be locked + * (wimax_dev->mutex). As well, most operations need to call this + * function to check if the state is the right one. + * + * An error value will be returned if the state is not the right + * one. In that case, the caller should not attempt to use the device + * and just unlock it. + */ +static inline __must_check +int wimax_dev_is_ready(struct wimax_dev *wimax_dev) +{ + if (wimax_dev->state == __WIMAX_ST_NULL) + return -EINVAL; /* Device is not even registered! */ + if (wimax_dev->state == WIMAX_ST_DOWN) + return -ENOMEDIUM; + if (wimax_dev->state == __WIMAX_ST_QUIESCING) + return -ESHUTDOWN; + return 0; +} + + +static inline +void __wimax_state_set(struct wimax_dev *wimax_dev, enum wimax_st state) +{ + wimax_dev->state = state; +} +extern void __wimax_state_change(struct wimax_dev *, enum wimax_st); + +#ifdef CONFIG_DEBUG_FS +extern int wimax_debugfs_add(struct wimax_dev *); +extern void wimax_debugfs_rm(struct wimax_dev *); +#else +static inline int wimax_debugfs_add(struct wimax_dev *wimax_dev) +{ + return 0; +} +static inline void wimax_debugfs_rm(struct wimax_dev *wimax_dev) {} +#endif + +extern void wimax_id_table_add(struct wimax_dev *); +extern struct wimax_dev *wimax_dev_get_by_genl_info(struct genl_info *, int); +extern void wimax_id_table_rm(struct wimax_dev *); +extern void wimax_id_table_release(void); + +extern int wimax_rfkill_add(struct wimax_dev *); +extern void wimax_rfkill_rm(struct wimax_dev *); + +extern struct genl_family wimax_gnl_family; +extern struct genl_multicast_group wimax_gnl_mcg; + +#endif /* #ifdef __KERNEL__ */ +#endif /* #ifndef __WIMAX_INTERNAL_H__ */ |