diff options
Diffstat (limited to 'include')
| -rw-r--r-- | include/linux/ieee80211.h | 30 | ||||
| -rw-r--r-- | include/net/cfg80211.h | 22 | ||||
| -rw-r--r-- | include/net/mac80211.h | 61 |
3 files changed, 109 insertions, 4 deletions
diff --git a/include/linux/ieee80211.h b/include/linux/ieee80211.h index 163c840437d6..d62edc7df3ae 100644 --- a/include/linux/ieee80211.h +++ b/include/linux/ieee80211.h @@ -707,6 +707,10 @@ struct ieee80211_mgmt { u8 action; u8 trans_id[WLAN_SA_QUERY_TR_ID_LEN]; } __attribute__ ((packed)) sa_query; + struct { + u8 action; + u8 smps_control; + } __attribute__ ((packed)) ht_smps; } u; } __attribute__ ((packed)) action; } u; @@ -771,7 +775,10 @@ struct ieee80211_bar { /** * struct ieee80211_mcs_info - MCS information * @rx_mask: RX mask - * @rx_highest: highest supported RX rate + * @rx_highest: highest supported RX rate. If set represents + * the highest supported RX data rate in units of 1 Mbps. + * If this field is 0 this value should not be used to + * consider the highest RX data rate supported. * @tx_params: TX parameters */ struct ieee80211_mcs_info { @@ -824,6 +831,7 @@ struct ieee80211_ht_cap { #define IEEE80211_HT_CAP_LDPC_CODING 0x0001 #define IEEE80211_HT_CAP_SUP_WIDTH_20_40 0x0002 #define IEEE80211_HT_CAP_SM_PS 0x000C +#define IEEE80211_HT_CAP_SM_PS_SHIFT 2 #define IEEE80211_HT_CAP_GRN_FLD 0x0010 #define IEEE80211_HT_CAP_SGI_20 0x0020 #define IEEE80211_HT_CAP_SGI_40 0x0040 @@ -839,6 +847,7 @@ struct ieee80211_ht_cap { /* 802.11n HT capability AMPDU settings (for ampdu_params_info) */ #define IEEE80211_HT_AMPDU_PARM_FACTOR 0x03 #define IEEE80211_HT_AMPDU_PARM_DENSITY 0x1C +#define IEEE80211_HT_AMPDU_PARM_DENSITY_SHIFT 2 /* * Maximum length of AMPDU that the STA can receive. @@ -922,12 +931,17 @@ struct ieee80211_ht_info { #define IEEE80211_MAX_AMPDU_BUF 0x40 -/* Spatial Multiplexing Power Save Modes */ +/* Spatial Multiplexing Power Save Modes (for capability) */ #define WLAN_HT_CAP_SM_PS_STATIC 0 #define WLAN_HT_CAP_SM_PS_DYNAMIC 1 #define WLAN_HT_CAP_SM_PS_INVALID 2 #define WLAN_HT_CAP_SM_PS_DISABLED 3 +/* for SM power control field lower two bits */ +#define WLAN_HT_SMPS_CONTROL_DISABLED 0 +#define WLAN_HT_SMPS_CONTROL_STATIC 1 +#define WLAN_HT_SMPS_CONTROL_DYNAMIC 3 + /* Authentication algorithms */ #define WLAN_AUTH_OPEN 0 #define WLAN_AUTH_SHARED_KEY 1 @@ -1150,6 +1164,18 @@ enum ieee80211_spectrum_mgmt_actioncode { WLAN_ACTION_SPCT_CHL_SWITCH = 4, }; +/* HT action codes */ +enum ieee80211_ht_actioncode { + WLAN_HT_ACTION_NOTIFY_CHANWIDTH = 0, + WLAN_HT_ACTION_SMPS = 1, + WLAN_HT_ACTION_PSMP = 2, + WLAN_HT_ACTION_PCO_PHASE = 3, + WLAN_HT_ACTION_CSI = 4, + WLAN_HT_ACTION_NONCOMPRESSED_BF = 5, + WLAN_HT_ACTION_COMPRESSED_BF = 6, + WLAN_HT_ACTION_ASEL_IDX_FEEDBACK = 7, +}; + /* Security key length */ enum ieee80211_key_len { WLAN_KEY_LEN_WEP40 = 5, diff --git a/include/net/cfg80211.h b/include/net/cfg80211.h index 0884b9a0f778..542a477a94da 100644 --- a/include/net/cfg80211.h +++ b/include/net/cfg80211.h @@ -1578,7 +1578,7 @@ unsigned int ieee80211_hdrlen(__le16 fc); * @addr: the device MAC address * @iftype: the virtual interface type */ -int ieee80211_data_to_8023(struct sk_buff *skb, u8 *addr, +int ieee80211_data_to_8023(struct sk_buff *skb, const u8 *addr, enum nl80211_iftype iftype); /** @@ -1589,10 +1589,28 @@ int ieee80211_data_to_8023(struct sk_buff *skb, u8 *addr, * @bssid: the network bssid (used only for iftype STATION and ADHOC) * @qos: build 802.11 QoS data frame */ -int ieee80211_data_from_8023(struct sk_buff *skb, u8 *addr, +int ieee80211_data_from_8023(struct sk_buff *skb, const u8 *addr, enum nl80211_iftype iftype, u8 *bssid, bool qos); /** + * ieee80211_amsdu_to_8023s - decode an IEEE 802.11n A-MSDU frame + * + * Decode an IEEE 802.11n A-MSDU frame and convert it to a list of + * 802.3 frames. The @list will be empty if the decode fails. The + * @skb is consumed after the function returns. + * + * @skb: The input IEEE 802.11n A-MSDU frame. + * @list: The output list of 802.3 frames. It must be allocated and + * initialized by by the caller. + * @addr: The device MAC address. + * @iftype: The device interface type. + * @extra_headroom: The hardware extra headroom for SKBs in the @list. + */ +void ieee80211_amsdu_to_8023s(struct sk_buff *skb, struct sk_buff_head *list, + const u8 *addr, enum nl80211_iftype iftype, + const unsigned int extra_headroom); + +/** * cfg80211_classify8021d - determine the 802.1p/1d tag for a data frame * @skb: the data frame */ diff --git a/include/net/mac80211.h b/include/net/mac80211.h index 538d6b761887..494ac69ff477 100644 --- a/include/net/mac80211.h +++ b/include/net/mac80211.h @@ -597,8 +597,10 @@ enum ieee80211_conf_flags { * @IEEE80211_CONF_CHANGE_CHANNEL: the channel/channel_type changed * @IEEE80211_CONF_CHANGE_RETRY_LIMITS: retry limits changed * @IEEE80211_CONF_CHANGE_IDLE: Idle flag changed + * @IEEE80211_CONF_CHANGE_SMPS: Spatial multiplexing powersave mode changed */ enum ieee80211_conf_changed { + IEEE80211_CONF_CHANGE_SMPS = BIT(1), IEEE80211_CONF_CHANGE_LISTEN_INTERVAL = BIT(2), IEEE80211_CONF_CHANGE_MONITOR = BIT(3), IEEE80211_CONF_CHANGE_PS = BIT(4), @@ -609,6 +611,21 @@ enum ieee80211_conf_changed { }; /** + * enum ieee80211_smps_mode - spatial multiplexing power save mode + * + * @ + */ +enum ieee80211_smps_mode { + IEEE80211_SMPS_AUTOMATIC, + IEEE80211_SMPS_OFF, + IEEE80211_SMPS_STATIC, + IEEE80211_SMPS_DYNAMIC, + + /* keep last */ + IEEE80211_SMPS_NUM_MODES, +}; + +/** * struct ieee80211_conf - configuration of the device * * This struct indicates how the driver shall configure the hardware. @@ -636,6 +653,10 @@ enum ieee80211_conf_changed { * @short_frame_max_tx_count: Maximum number of transmissions for a "short" * frame, called "dot11ShortRetryLimit" in 802.11, but actually means the * number of transmissions not the number of retries + * + * @smps_mode: spatial multiplexing powersave mode; note that + * %IEEE80211_SMPS_STATIC is used when the device is not + * configured for an HT channel */ struct ieee80211_conf { u32 flags; @@ -648,6 +669,7 @@ struct ieee80211_conf { struct ieee80211_channel *channel; enum nl80211_channel_type channel_type; + enum ieee80211_smps_mode smps_mode; }; /** @@ -659,12 +681,14 @@ struct ieee80211_conf { * @type: type of this virtual interface * @bss_conf: BSS configuration for this interface, either our own * or the BSS we're associated to + * @addr: address of this interface * @drv_priv: data area for driver use, will always be aligned to * sizeof(void *). */ struct ieee80211_vif { enum nl80211_iftype type; struct ieee80211_bss_conf bss_conf; + u8 addr[ETH_ALEN]; /* must be last */ u8 drv_priv[0] __attribute__((__aligned__(sizeof(void *)))); }; @@ -928,6 +952,16 @@ enum ieee80211_tkip_key_type { * @IEEE80211_HW_BEACON_FILTER: * Hardware supports dropping of irrelevant beacon frames to * avoid waking up cpu. + * + * @IEEE80211_HW_SUPPORTS_STATIC_SMPS: + * Hardware supports static spatial multiplexing powersave, + * ie. can turn off all but one chain even on HT connections + * that should be using more chains. + * + * @IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS: + * Hardware supports dynamic spatial multiplexing powersave, + * ie. can turn off all but one chain and then wake the rest + * up as required after, for example, rts/cts handshake. */ enum ieee80211_hw_flags { IEEE80211_HW_HAS_RATE_CONTROL = 1<<0, @@ -945,6 +979,8 @@ enum ieee80211_hw_flags { IEEE80211_HW_SUPPORTS_DYNAMIC_PS = 1<<12, IEEE80211_HW_MFP_CAPABLE = 1<<13, IEEE80211_HW_BEACON_FILTER = 1<<14, + IEEE80211_HW_SUPPORTS_STATIC_SMPS = 1<<15, + IEEE80211_HW_SUPPORTS_DYNAMIC_SMPS = 1<<16, }; /** @@ -1213,6 +1249,31 @@ ieee80211_get_alt_retry_rate(const struct ieee80211_hw *hw, */ /** + * DOC: Spatial multiplexing power save + * + * SMPS (Spatial multiplexing power save) is a mechanism to conserve + * power in an 802.11n implementation. For details on the mechanism + * and rationale, please refer to 802.11 (as amended by 802.11n-2009) + * "11.2.3 SM power save". + * + * The mac80211 implementation is capable of sending action frames + * to update the AP about the station's SMPS mode, and will instruct + * the driver to enter the specific mode. It will also announce the + * requested SMPS mode during the association handshake. Hardware + * support for this feature is required, and can be indicated by + * hardware flags. + * + * The default mode will be "automatic", which nl80211/cfg80211 + * defines to be dynamic SMPS in (regular) powersave, and SMPS + * turned off otherwise. + * + * To support this feature, the driver must set the appropriate + * hardware support flags, and handle the SMPS flag to the config() + * operation. It will then with this mechanism be instructed to + * enter the requested SMPS mode while associated to an HT AP. + */ + +/** * DOC: Frame filtering * * mac80211 requires to see many management frames for proper |