diff options
Diffstat (limited to 'include/linux/zlib.h')
| -rw-r--r-- | include/linux/zlib.h | 118 |
1 files changed, 0 insertions, 118 deletions
diff --git a/include/linux/zlib.h b/include/linux/zlib.h index 9c5a6b4de0a3..197abb2a54c5 100644 --- a/include/linux/zlib.h +++ b/include/linux/zlib.h @@ -493,64 +493,6 @@ extern int deflateInit2 (z_streamp strm, method). msg is set to null if there is no error message. deflateInit2 does not perform any compression: this will be done by deflate(). */ - -#if 0 -extern int zlib_deflateSetDictionary (z_streamp strm, - const Byte *dictionary, - uInt dictLength); -#endif -/* - Initializes the compression dictionary from the given byte sequence - without producing any compressed output. This function must be called - immediately after deflateInit, deflateInit2 or deflateReset, before any - call of deflate. The compressor and decompressor must use exactly the same - dictionary (see inflateSetDictionary). - - The dictionary should consist of strings (byte sequences) that are likely - to be encountered later in the data to be compressed, with the most commonly - used strings preferably put towards the end of the dictionary. Using a - dictionary is most useful when the data to be compressed is short and can be - predicted with good accuracy; the data can then be compressed better than - with the default empty dictionary. - - Depending on the size of the compression data structures selected by - deflateInit or deflateInit2, a part of the dictionary may in effect be - discarded, for example if the dictionary is larger than the window size in - deflate or deflate2. Thus the strings most likely to be useful should be - put at the end of the dictionary, not at the front. - - Upon return of this function, strm->adler is set to the Adler32 value - of the dictionary; the decompressor may later use this value to determine - which dictionary has been used by the compressor. (The Adler32 value - applies to the whole dictionary even if only a subset of the dictionary is - actually used by the compressor.) - - deflateSetDictionary returns Z_OK if success, or Z_STREAM_ERROR if a - parameter is invalid (such as NULL dictionary) or the stream state is - inconsistent (for example if deflate has already been called for this stream - or if the compression method is bsort). deflateSetDictionary does not - perform any compression: this will be done by deflate(). -*/ - -#if 0 -extern int zlib_deflateCopy (z_streamp dest, z_streamp source); -#endif - -/* - Sets the destination stream as a complete copy of the source stream. - - This function can be useful when several compression strategies will be - tried, for example when there are several ways of pre-processing the input - data with a filter. The streams that will be discarded should then be freed - by calling deflateEnd. Note that deflateCopy duplicates the internal - compression state which can be quite large, so this strategy is slow and - can consume lots of memory. - - deflateCopy returns Z_OK if success, Z_MEM_ERROR if there was not - enough memory, Z_STREAM_ERROR if the source stream state was inconsistent - (such as zalloc being NULL). msg is left unchanged in both source and - destination. -*/ extern int zlib_deflateReset (z_streamp strm); /* @@ -568,27 +510,6 @@ static inline unsigned long deflateBound(unsigned long s) return s + ((s + 7) >> 3) + ((s + 63) >> 6) + 11; } -#if 0 -extern int zlib_deflateParams (z_streamp strm, int level, int strategy); -#endif -/* - Dynamically update the compression level and compression strategy. The - interpretation of level and strategy is as in deflateInit2. This can be - used to switch between compression and straight copy of the input data, or - to switch to a different kind of input data requiring a different - strategy. If the compression level is changed, the input available so far - is compressed with the old level (and may be flushed); the new level will - take effect only at the next call of deflate(). - - Before the call of deflateParams, the stream state must be set as for - a call of deflate(), since the currently available input may have to - be compressed and flushed. In particular, strm->avail_out must be non-zero. - - deflateParams returns Z_OK if success, Z_STREAM_ERROR if the source - stream state was inconsistent or if a parameter was invalid, Z_BUF_ERROR - if strm->avail_out was zero. -*/ - /* extern int inflateInit2 (z_streamp strm, int windowBits); @@ -631,45 +552,6 @@ extern int inflateInit2 (z_streamp strm, int windowBits); and avail_out are unchanged.) */ -extern int zlib_inflateSetDictionary (z_streamp strm, - const Byte *dictionary, - uInt dictLength); -/* - Initializes the decompression dictionary from the given uncompressed byte - sequence. This function must be called immediately after a call of inflate, - if that call returned Z_NEED_DICT. The dictionary chosen by the compressor - can be determined from the adler32 value returned by that call of inflate. - The compressor and decompressor must use exactly the same dictionary (see - deflateSetDictionary). For raw inflate, this function can be called - immediately after inflateInit2() or inflateReset() and before any call of - inflate() to set the dictionary. The application must insure that the - dictionary that was used for compression is provided. - - inflateSetDictionary returns Z_OK if success, Z_STREAM_ERROR if a - parameter is invalid (such as NULL dictionary) or the stream state is - inconsistent, Z_DATA_ERROR if the given dictionary doesn't match the - expected one (incorrect adler32 value). inflateSetDictionary does not - perform any decompression: this will be done by subsequent calls of - inflate(). -*/ - -#if 0 -extern int zlib_inflateSync (z_streamp strm); -#endif -/* - Skips invalid compressed data until a full flush point (see above the - description of deflate with Z_FULL_FLUSH) can be found, or until all - available input is skipped. No output is provided. - - inflateSync returns Z_OK if a full flush point has been found, Z_BUF_ERROR - if no more input was provided, Z_DATA_ERROR if no flush point has been found, - or Z_STREAM_ERROR if the stream structure was inconsistent. In the success - case, the application may save the current current value of total_in which - indicates where valid compressed data was found. In the error case, the - application may repeatedly call inflateSync, providing more input each time, - until success or end of the input data. -*/ - extern int zlib_inflateReset (z_streamp strm); /* This function is equivalent to inflateEnd followed by inflateInit, |