diff options
Diffstat (limited to 'include/linux/spi/pxa2xx_spi.h')
| -rw-r--r-- | include/linux/spi/pxa2xx_spi.h | 152 |
1 files changed, 152 insertions, 0 deletions
diff --git a/include/linux/spi/pxa2xx_spi.h b/include/linux/spi/pxa2xx_spi.h new file mode 100644 index 000000000000..d3e1075f7b60 --- /dev/null +++ b/include/linux/spi/pxa2xx_spi.h @@ -0,0 +1,152 @@ +/* + * Copyright (C) 2005 Stephen Street / StreetFire Sound Labs + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + * You should have received a copy of the GNU General Public License + * along with this program; if not, write to the Free Software + * Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. + */ +#ifndef __linux_pxa2xx_spi_h +#define __linux_pxa2xx_spi_h + +#include <linux/pxa2xx_ssp.h> + +#define PXA2XX_CS_ASSERT (0x01) +#define PXA2XX_CS_DEASSERT (0x02) + +/* device.platform_data for SSP controller devices */ +struct pxa2xx_spi_master { + u32 clock_enable; + u16 num_chipselect; + u8 enable_dma; +}; + +/* spi_board_info.controller_data for SPI slave devices, + * copied to spi_device.platform_data ... mostly for dma tuning + */ +struct pxa2xx_spi_chip { + u8 tx_threshold; + u8 rx_threshold; + u8 dma_burst_size; + u32 timeout; + u8 enable_loopback; + int gpio_cs; + void (*cs_control)(u32 command); +}; + +#ifdef CONFIG_ARCH_PXA + +#include <linux/clk.h> +#include <mach/dma.h> + +extern void pxa2xx_set_spi_info(unsigned id, struct pxa2xx_spi_master *info); + +#else +/* + * This is the implemtation for CE4100 on x86. ARM defines them in mach/ or + * plat/ include path. + * The CE4100 does not provide DMA support. This bits are here to let the driver + * compile and will never be used. Maybe we get DMA support at a later point in + * time. + */ + +#define DCSR(n) (n) +#define DSADR(n) (n) +#define DTADR(n) (n) +#define DCMD(n) (n) +#define DRCMR(n) (n) + +#define DCSR_RUN (1 << 31) /* Run Bit */ +#define DCSR_NODESC (1 << 30) /* No-Descriptor Fetch */ +#define DCSR_STOPIRQEN (1 << 29) /* Stop Interrupt Enable */ +#define DCSR_REQPEND (1 << 8) /* Request Pending (read-only) */ +#define DCSR_STOPSTATE (1 << 3) /* Stop State (read-only) */ +#define DCSR_ENDINTR (1 << 2) /* End Interrupt */ +#define DCSR_STARTINTR (1 << 1) /* Start Interrupt */ +#define DCSR_BUSERR (1 << 0) /* Bus Error Interrupt */ + +#define DCSR_EORIRQEN (1 << 28) /* End of Receive Interrupt Enable */ +#define DCSR_EORJMPEN (1 << 27) /* Jump to next descriptor on EOR */ +#define DCSR_EORSTOPEN (1 << 26) /* STOP on an EOR */ +#define DCSR_SETCMPST (1 << 25) /* Set Descriptor Compare Status */ +#define DCSR_CLRCMPST (1 << 24) /* Clear Descriptor Compare Status */ +#define DCSR_CMPST (1 << 10) /* The Descriptor Compare Status */ +#define DCSR_EORINTR (1 << 9) /* The end of Receive */ + +#define DRCMR_MAPVLD (1 << 7) /* Map Valid */ +#define DRCMR_CHLNUM 0x1f /* mask for Channel Number */ + +#define DDADR_DESCADDR 0xfffffff0 /* Address of next descriptor */ +#define DDADR_STOP (1 << 0) /* Stop */ + +#define DCMD_INCSRCADDR (1 << 31) /* Source Address Increment Setting. */ +#define DCMD_INCTRGADDR (1 << 30) /* Target Address Increment Setting. */ +#define DCMD_FLOWSRC (1 << 29) /* Flow Control by the source. */ +#define DCMD_FLOWTRG (1 << 28) /* Flow Control by the target. */ +#define DCMD_STARTIRQEN (1 << 22) /* Start Interrupt Enable */ +#define DCMD_ENDIRQEN (1 << 21) /* End Interrupt Enable */ +#define DCMD_ENDIAN (1 << 18) /* Device Endian-ness. */ +#define DCMD_BURST8 (1 << 16) /* 8 byte burst */ +#define DCMD_BURST16 (2 << 16) /* 16 byte burst */ +#define DCMD_BURST32 (3 << 16) /* 32 byte burst */ +#define DCMD_WIDTH1 (1 << 14) /* 1 byte width */ +#define DCMD_WIDTH2 (2 << 14) /* 2 byte width (HalfWord) */ +#define DCMD_WIDTH4 (3 << 14) /* 4 byte width (Word) */ +#define DCMD_LENGTH 0x01fff /* length mask (max = 8K - 1) */ + +/* + * Descriptor structure for PXA's DMA engine + * Note: this structure must always be aligned to a 16-byte boundary. + */ + +typedef enum { + DMA_PRIO_HIGH = 0, + DMA_PRIO_MEDIUM = 1, + DMA_PRIO_LOW = 2 +} pxa_dma_prio; + +/* + * DMA registration + */ + +static inline int pxa_request_dma(char *name, + pxa_dma_prio prio, + void (*irq_handler)(int, void *), + void *data) +{ + return -ENODEV; +} + +static inline void pxa_free_dma(int dma_ch) +{ +} + +/* + * The CE4100 does not have the clk framework implemented and SPI clock can + * not be switched on/off or the divider changed. + */ +static inline void clk_disable(struct clk *clk) +{ +} + +static inline int clk_enable(struct clk *clk) +{ + return 0; +} + +static inline unsigned long clk_get_rate(struct clk *clk) +{ + return 3686400; +} + +#endif +#endif |