summaryrefslogtreecommitdiff
path: root/drivers
diff options
context:
space:
mode:
Diffstat (limited to 'drivers')
-rw-r--r--drivers/net/ethernet/8390/Kconfig66
-rw-r--r--drivers/net/ethernet/8390/Makefile5
-rw-r--r--drivers/net/ethernet/8390/ac3200.c431
-rw-r--r--drivers/net/ethernet/8390/es3210.c445
-rw-r--r--drivers/net/ethernet/8390/lne390.c433
-rw-r--r--drivers/net/ethernet/8390/ne3210.c346
-rw-r--r--drivers/net/ethernet/8390/smc-ultra32.c463
7 files changed, 2 insertions, 2187 deletions
diff --git a/drivers/net/ethernet/8390/Kconfig b/drivers/net/ethernet/8390/Kconfig
index 880121730cb0..e49a44221800 100644
--- a/drivers/net/ethernet/8390/Kconfig
+++ b/drivers/net/ethernet/8390/Kconfig
@@ -6,7 +6,7 @@ config NET_VENDOR_8390
bool "National Semi-conductor 8390 devices"
default y
depends on NET_VENDOR_NATSEMI && (AMIGA_PCMCIA || PCI || SUPERH || \
- ISA || EISA || MAC || M32R || MACH_TX49XX || \
+ ISA || MAC || M32R || MACH_TX49XX || \
H8300 || ARM || MIPS || ZORRO || PCMCIA || \
EXPERIMENTAL)
---help---
@@ -33,18 +33,6 @@ config EL2
To compile this driver as a module, choose M here. The module
will be called 3c503.
-config AC3200
- tristate "Ansel Communications EISA 3200 support (EXPERIMENTAL)"
- depends on PCI && (ISA || EISA) && EXPERIMENTAL
- select CRC32
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called ac3200.
-
config PCMCIA_AXNET
tristate "Asix AX88190 PCMCIA support"
depends on PCMCIA
@@ -86,18 +74,6 @@ config E2100
To compile this driver as a module, choose M here. The module
will be called e2100.
-config ES3210
- tristate "Racal-Interlan EISA ES3210 support (EXPERIMENTAL)"
- depends on PCI && EISA && EXPERIMENTAL
- select CRC32
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called es3210.
-
config HPLAN_PLUS
tristate "HP PCLAN+ (27247B and 27252A) support"
depends on ISA
@@ -140,18 +116,6 @@ config ARM_ETHERH
If you have an Acorn system with one of these network cards, you
should say Y to this option if you wish to use it with Linux.
-config LNE390
- tristate "Mylex EISA LNE390A/B support (EXPERIMENTAL)"
- depends on PCI && EISA && EXPERIMENTAL
- select CRC32
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called lne390.
-
config MAC8390
bool "Macintosh NS 8390 based ethernet cards"
depends on MAC
@@ -187,8 +151,7 @@ config NE2000
without a specific driver are compatible with NE2000.
If you have a PCI NE2000 card however, say N here and Y to "PCI
- NE2000 and clone support" under "EISA, VLB, PCI and on board
- controllers" below.
+ NE2000 and clone support" below.
To compile this driver as a module, choose M here. The module
will be called ne.
@@ -223,19 +186,6 @@ config APNE
To compile this driver as a module, choose M here: the module
will be called apne.
-config NE3210
- tristate "Novell/Eagle/Microdyne NE3210 EISA support (EXPERIMENTAL)"
- depends on PCI && EISA && EXPERIMENTAL
- select CRC32
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>. Note that this driver
- will NOT WORK for NE3200 cards as they are completely different.
-
- To compile this driver as a module, choose M here. The module
- will be called ne3210.
-
config PCMCIA_PCNET
tristate "NE2000 compatible PCMCIA support"
depends on PCMCIA
@@ -285,18 +235,6 @@ config ULTRA
To compile this driver as a module, choose M here. The module
will be called smc-ultra.
-config ULTRA32
- tristate "SMC Ultra32 EISA support"
- depends on EISA
- select CRC32
- ---help---
- If you have a network (Ethernet) card of this type, say Y and read
- the Ethernet-HOWTO, available from
- <http://www.tldp.org/docs.html#howto>.
-
- To compile this driver as a module, choose M here. The module
- will be called smc-ultra32.
-
config WD80x3
tristate "WD80*3 support"
depends on ISA
diff --git a/drivers/net/ethernet/8390/Makefile b/drivers/net/ethernet/8390/Makefile
index 8fb462cb9774..e8bb97cd355f 100644
--- a/drivers/net/ethernet/8390/Makefile
+++ b/drivers/net/ethernet/8390/Makefile
@@ -3,26 +3,21 @@
#
obj-$(CONFIG_MAC8390) += mac8390.o
-obj-$(CONFIG_AC3200) += ac3200.o 8390.o
obj-$(CONFIG_APNE) += apne.o 8390.o
obj-$(CONFIG_ARM_ETHERH) += etherh.o
obj-$(CONFIG_AX88796) += ax88796.o
obj-$(CONFIG_E2100) += e2100.o 8390.o
obj-$(CONFIG_EL2) += 3c503.o 8390p.o
-obj-$(CONFIG_ES3210) += es3210.o 8390.o
obj-$(CONFIG_HPLAN_PLUS) += hp-plus.o 8390p.o
obj-$(CONFIG_HPLAN) += hp.o 8390p.o
obj-$(CONFIG_HYDRA) += hydra.o 8390.o
-obj-$(CONFIG_LNE390) += lne390.o 8390.o
obj-$(CONFIG_MCF8390) += mcf8390.o 8390.o
obj-$(CONFIG_NE2000) += ne.o 8390p.o
obj-$(CONFIG_NE2K_PCI) += ne2k-pci.o 8390.o
-obj-$(CONFIG_NE3210) += ne3210.o 8390.o
obj-$(CONFIG_NE_H8300) += ne-h8300.o 8390.o
obj-$(CONFIG_PCMCIA_AXNET) += axnet_cs.o 8390.o
obj-$(CONFIG_PCMCIA_PCNET) += pcnet_cs.o 8390.o
obj-$(CONFIG_STNIC) += stnic.o 8390.o
obj-$(CONFIG_ULTRA) += smc-ultra.o 8390.o
-obj-$(CONFIG_ULTRA32) += smc-ultra32.o 8390.o
obj-$(CONFIG_WD80x3) += wd.o 8390.o
obj-$(CONFIG_ZORRO8390) += zorro8390.o 8390.o
diff --git a/drivers/net/ethernet/8390/ac3200.c b/drivers/net/ethernet/8390/ac3200.c
deleted file mode 100644
index ccf07942ff6e..000000000000
--- a/drivers/net/ethernet/8390/ac3200.c
+++ /dev/null
@@ -1,431 +0,0 @@
-/* ac3200.c: A driver for the Ansel Communications EISA ethernet adaptor. */
-/*
- Written 1993, 1994 by Donald Becker.
- Copyright 1993 United States Government as represented by the Director,
- National Security Agency. This software may only be used and distributed
- according to the terms of the GNU General Public License as modified by SRC,
- incorporated herein by reference.
-
- The author may be reached as becker@scyld.com, or C/O
- Scyld Computing Corporation
- 410 Severn Ave., Suite 210
- Annapolis MD 21403
-
- This is driver for the Ansel Communications Model 3200 EISA Ethernet LAN
- Adapter. The programming information is from the users manual, as related
- by glee@ardnassak.math.clemson.edu.
-
- Changelog:
-
- Paul Gortmaker 05/98 : add support for shared mem above 1MB.
-
- */
-
-static const char version[] =
- "ac3200.c:v1.01 7/1/94 Donald Becker (becker@cesdis.gsfc.nasa.gov)\n";
-
-#include <linux/module.h>
-#include <linux/eisa.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-
-#include <asm/io.h>
-#include <asm/irq.h>
-
-#include "8390.h"
-
-#define DRV_NAME "ac3200"
-
-/* Offsets from the base address. */
-#define AC_NIC_BASE 0x00
-#define AC_SA_PROM 0x16 /* The station address PROM. */
-#define AC_ADDR0 0x00 /* Prefix station address values. */
-#define AC_ADDR1 0x40
-#define AC_ADDR2 0x90
-#define AC_ID_PORT 0xC80
-#define AC_EISA_ID 0x0110d305
-#define AC_RESET_PORT 0xC84
-#define AC_RESET 0x00
-#define AC_ENABLE 0x01
-#define AC_CONFIG 0xC90 /* The configuration port. */
-
-#define AC_IO_EXTENT 0x20
- /* Actually accessed is:
- * AC_NIC_BASE (0-15)
- * AC_SA_PROM (0-5)
- * AC_ID_PORT (0-3)
- * AC_RESET_PORT
- * AC_CONFIG
- */
-
-/* Decoding of the configuration register. */
-static unsigned char config2irqmap[8] __initdata = {15, 12, 11, 10, 9, 7, 5, 3};
-static int addrmap[8] =
-{0xFF0000, 0xFE0000, 0xFD0000, 0xFFF0000, 0xFFE0000, 0xFFC0000, 0xD0000, 0 };
-static const char *port_name[4] = { "10baseT", "invalid", "AUI", "10base2"};
-
-#define config2irq(configval) config2irqmap[((configval) >> 3) & 7]
-#define config2mem(configval) addrmap[(configval) & 7]
-#define config2name(configval) port_name[((configval) >> 6) & 3]
-
-/* First and last 8390 pages. */
-#define AC_START_PG 0x00 /* First page of 8390 TX buffer */
-#define AC_STOP_PG 0x80 /* Last page +1 of the 8390 RX ring */
-
-static int ac_probe1(int ioaddr, struct net_device *dev);
-
-static int ac_open(struct net_device *dev);
-static void ac_reset_8390(struct net_device *dev);
-static void ac_block_input(struct net_device *dev, int count,
- struct sk_buff *skb, int ring_offset);
-static void ac_block_output(struct net_device *dev, const int count,
- const unsigned char *buf, const int start_page);
-static void ac_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
- int ring_page);
-
-static int ac_close_card(struct net_device *dev);
-
-
-/* Probe for the AC3200.
-
- The AC3200 can be identified by either the EISA configuration registers,
- or the unique value in the station address PROM.
- */
-
-static int __init do_ac3200_probe(struct net_device *dev)
-{
- unsigned short ioaddr = dev->base_addr;
- int irq = dev->irq;
- int mem_start = dev->mem_start;
-
- if (ioaddr > 0x1ff) /* Check a single specified location. */
- return ac_probe1(ioaddr, dev);
- else if (ioaddr > 0) /* Don't probe at all. */
- return -ENXIO;
-
- if ( ! EISA_bus)
- return -ENXIO;
-
- for (ioaddr = 0x1000; ioaddr < 0x9000; ioaddr += 0x1000) {
- if (ac_probe1(ioaddr, dev) == 0)
- return 0;
- dev->irq = irq;
- dev->mem_start = mem_start;
- }
-
- return -ENODEV;
-}
-
-#ifndef MODULE
-struct net_device * __init ac3200_probe(int unit)
-{
- struct net_device *dev = alloc_ei_netdev();
- int err;
-
- if (!dev)
- return ERR_PTR(-ENOMEM);
-
- sprintf(dev->name, "eth%d", unit);
- netdev_boot_setup_check(dev);
-
- err = do_ac3200_probe(dev);
- if (err)
- goto out;
- return dev;
-out:
- free_netdev(dev);
- return ERR_PTR(err);
-}
-#endif
-
-static const struct net_device_ops ac_netdev_ops = {
- .ndo_open = ac_open,
- .ndo_stop = ac_close_card,
-
- .ndo_start_xmit = ei_start_xmit,
- .ndo_tx_timeout = ei_tx_timeout,
- .ndo_get_stats = ei_get_stats,
- .ndo_set_rx_mode = ei_set_multicast_list,
- .ndo_validate_addr = eth_validate_addr,
- .ndo_set_mac_address = eth_mac_addr,
- .ndo_change_mtu = eth_change_mtu,
-#ifdef CONFIG_NET_POLL_CONTROLLER
- .ndo_poll_controller = ei_poll,
-#endif
-};
-
-static int __init ac_probe1(int ioaddr, struct net_device *dev)
-{
- int i, retval;
-
- if (!request_region(ioaddr, AC_IO_EXTENT, DRV_NAME))
- return -EBUSY;
-
- if (inb_p(ioaddr + AC_ID_PORT) == 0xff) {
- retval = -ENODEV;
- goto out;
- }
-
- if (inl(ioaddr + AC_ID_PORT) != AC_EISA_ID) {
- retval = -ENODEV;
- goto out;
- }
-
-#ifndef final_version
- printk(KERN_DEBUG "AC3200 ethercard configuration register is %#02x,"
- " EISA ID %02x %02x %02x %02x.\n", inb(ioaddr + AC_CONFIG),
- inb(ioaddr + AC_ID_PORT + 0), inb(ioaddr + AC_ID_PORT + 1),
- inb(ioaddr + AC_ID_PORT + 2), inb(ioaddr + AC_ID_PORT + 3));
-#endif
-
- for (i = 0; i < 6; i++)
- dev->dev_addr[i] = inb(ioaddr + AC_SA_PROM + i);
-
- printk(KERN_DEBUG "AC3200 in EISA slot %d, node %pM",
- ioaddr/0x1000, dev->dev_addr);
-#if 0
- /* Check the vendor ID/prefix. Redundant after checking the EISA ID */
- if (inb(ioaddr + AC_SA_PROM + 0) != AC_ADDR0
- || inb(ioaddr + AC_SA_PROM + 1) != AC_ADDR1
- || inb(ioaddr + AC_SA_PROM + 2) != AC_ADDR2 ) {
- printk(", not found (invalid prefix).\n");
- retval = -ENODEV;
- goto out;
- }
-#endif
-
- /* Assign and allocate the interrupt now. */
- if (dev->irq == 0) {
- dev->irq = config2irq(inb(ioaddr + AC_CONFIG));
- printk(", using");
- } else {
- dev->irq = irq_canonicalize(dev->irq);
- printk(", assigning");
- }
-
- retval = request_irq(dev->irq, ei_interrupt, 0, DRV_NAME, dev);
- if (retval) {
- printk (" nothing! Unable to get IRQ %d.\n", dev->irq);
- goto out;
- }
-
- printk(" IRQ %d, %s port\n", dev->irq, port_name[dev->if_port]);
-
- dev->base_addr = ioaddr;
-
-#ifdef notyet
- if (dev->mem_start) { /* Override the value from the board. */
- for (i = 0; i < 7; i++)
- if (addrmap[i] == dev->mem_start)
- break;
- if (i >= 7)
- i = 0;
- outb((inb(ioaddr + AC_CONFIG) & ~7) | i, ioaddr + AC_CONFIG);
- }
-#endif
-
- dev->if_port = inb(ioaddr + AC_CONFIG) >> 6;
- dev->mem_start = config2mem(inb(ioaddr + AC_CONFIG));
-
- printk("%s: AC3200 at %#3x with %dkB memory at physical address %#lx.\n",
- dev->name, ioaddr, AC_STOP_PG/4, dev->mem_start);
-
- /*
- * BEWARE!! Some dain-bramaged EISA SCUs will allow you to put
- * the card mem within the region covered by `normal' RAM !!!
- *
- * ioremap() will fail in that case.
- */
- ei_status.mem = ioremap(dev->mem_start, AC_STOP_PG*0x100);
- if (!ei_status.mem) {
- printk(KERN_ERR "ac3200.c: Unable to remap card memory above 1MB !!\n");
- printk(KERN_ERR "ac3200.c: Try using EISA SCU to set memory below 1MB.\n");
- printk(KERN_ERR "ac3200.c: Driver NOT installed.\n");
- retval = -EINVAL;
- goto out1;
- }
- printk("ac3200.c: remapped %dkB card memory to virtual address %p\n",
- AC_STOP_PG/4, ei_status.mem);
-
- dev->mem_start = (unsigned long)ei_status.mem;
- dev->mem_end = dev->mem_start + (AC_STOP_PG - AC_START_PG)*256;
-
- ei_status.name = "AC3200";
- ei_status.tx_start_page = AC_START_PG;
- ei_status.rx_start_page = AC_START_PG + TX_PAGES;
- ei_status.stop_page = AC_STOP_PG;
- ei_status.word16 = 1;
-
- if (ei_debug > 0)
- printk(version);
-
- ei_status.reset_8390 = &ac_reset_8390;
- ei_status.block_input = &ac_block_input;
- ei_status.block_output = &ac_block_output;
- ei_status.get_8390_hdr = &ac_get_8390_hdr;
-
- dev->netdev_ops = &ac_netdev_ops;
- NS8390_init(dev, 0);
-
- retval = register_netdev(dev);
- if (retval)
- goto out2;
- return 0;
-out2:
- if (ei_status.reg0)
- iounmap(ei_status.mem);
-out1:
- free_irq(dev->irq, dev);
-out:
- release_region(ioaddr, AC_IO_EXTENT);
- return retval;
-}
-
-static int ac_open(struct net_device *dev)
-{
-#ifdef notyet
- /* Someday we may enable the IRQ and shared memory here. */
- int ioaddr = dev->base_addr;
-#endif
-
- ei_open(dev);
- return 0;
-}
-
-static void ac_reset_8390(struct net_device *dev)
-{
- ushort ioaddr = dev->base_addr;
-
- outb(AC_RESET, ioaddr + AC_RESET_PORT);
- if (ei_debug > 1) printk("resetting AC3200, t=%ld...", jiffies);
-
- ei_status.txing = 0;
- outb(AC_ENABLE, ioaddr + AC_RESET_PORT);
- if (ei_debug > 1) printk("reset done\n");
-}
-
-/* Grab the 8390 specific header. Similar to the block_input routine, but
- we don't need to be concerned with ring wrap as the header will be at
- the start of a page, so we optimize accordingly. */
-
-static void
-ac_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page)
-{
- void __iomem *hdr_start = ei_status.mem + ((ring_page - AC_START_PG)<<8);
- memcpy_fromio(hdr, hdr_start, sizeof(struct e8390_pkt_hdr));
-}
-
-/* Block input and output are easy on shared memory ethercards, the only
- complication is when the ring buffer wraps. */
-
-static void ac_block_input(struct net_device *dev, int count, struct sk_buff *skb,
- int ring_offset)
-{
- void __iomem *start = ei_status.mem + ring_offset - AC_START_PG*256;
-
- if (ring_offset + count > AC_STOP_PG*256) {
- /* We must wrap the input move. */
- int semi_count = AC_STOP_PG*256 - ring_offset;
- memcpy_fromio(skb->data, start, semi_count);
- count -= semi_count;
- memcpy_fromio(skb->data + semi_count,
- ei_status.mem + TX_PAGES*256, count);
- } else {
- memcpy_fromio(skb->data, start, count);
- }
-}
-
-static void ac_block_output(struct net_device *dev, int count,
- const unsigned char *buf, int start_page)
-{
- void __iomem *shmem = ei_status.mem + ((start_page - AC_START_PG)<<8);
-
- memcpy_toio(shmem, buf, count);
-}
-
-static int ac_close_card(struct net_device *dev)
-{
- if (ei_debug > 1)
- printk("%s: Shutting down ethercard.\n", dev->name);
-
-#ifdef notyet
- /* We should someday disable shared memory and interrupts. */
- outb(0x00, ioaddr + 6); /* Disable interrupts. */
- free_irq(dev->irq, dev);
-#endif
-
- ei_close(dev);
- return 0;
-}
-
-#ifdef MODULE
-#define MAX_AC32_CARDS 4 /* Max number of AC32 cards per module */
-static struct net_device *dev_ac32[MAX_AC32_CARDS];
-static int io[MAX_AC32_CARDS];
-static int irq[MAX_AC32_CARDS];
-static int mem[MAX_AC32_CARDS];
-module_param_array(io, int, NULL, 0);
-module_param_array(irq, int, NULL, 0);
-module_param_array(mem, int, NULL, 0);
-MODULE_PARM_DESC(io, "I/O base address(es)");
-MODULE_PARM_DESC(irq, "IRQ number(s)");
-MODULE_PARM_DESC(mem, "Memory base address(es)");
-MODULE_DESCRIPTION("Ansel AC3200 EISA ethernet driver");
-MODULE_LICENSE("GPL");
-
-static int __init ac3200_module_init(void)
-{
- struct net_device *dev;
- int this_dev, found = 0;
-
- for (this_dev = 0; this_dev < MAX_AC32_CARDS; this_dev++) {
- if (io[this_dev] == 0 && this_dev != 0)
- break;
- dev = alloc_ei_netdev();
- if (!dev)
- break;
- dev->irq = irq[this_dev];
- dev->base_addr = io[this_dev];
- dev->mem_start = mem[this_dev]; /* Currently ignored by driver */
- if (do_ac3200_probe(dev) == 0) {
- dev_ac32[found++] = dev;
- continue;
- }
- free_netdev(dev);
- printk(KERN_WARNING "ac3200.c: No ac3200 card found (i/o = 0x%x).\n", io[this_dev]);
- break;
- }
- if (found)
- return 0;
- return -ENXIO;
-}
-
-static void cleanup_card(struct net_device *dev)
-{
- /* Someday free_irq may be in ac_close_card() */
- free_irq(dev->irq, dev);
- release_region(dev->base_addr, AC_IO_EXTENT);
- iounmap(ei_status.mem);
-}
-
-static void __exit ac3200_module_exit(void)
-{
- int this_dev;
-
- for (this_dev = 0; this_dev < MAX_AC32_CARDS; this_dev++) {
- struct net_device *dev = dev_ac32[this_dev];
- if (dev) {
- unregister_netdev(dev);
- cleanup_card(dev);
- free_netdev(dev);
- }
- }
-}
-module_init(ac3200_module_init);
-module_exit(ac3200_module_exit);
-#endif /* MODULE */
diff --git a/drivers/net/ethernet/8390/es3210.c b/drivers/net/ethernet/8390/es3210.c
deleted file mode 100644
index ba1b5c95531f..000000000000
--- a/drivers/net/ethernet/8390/es3210.c
+++ /dev/null
@@ -1,445 +0,0 @@
-/*
- es3210.c
-
- Linux driver for Racal-Interlan ES3210 EISA Network Adapter
-
- Copyright (C) 1996, Paul Gortmaker.
-
- This software may be used and distributed according to the terms
- of the GNU General Public License, incorporated herein by reference.
-
- Information and Code Sources:
-
- 1) The existing myriad of Linux 8390 drivers written by Donald Becker.
-
- 2) Once again Russ Nelson's asm packet driver provided additional info.
-
- 3) Info for getting IRQ and sh-mem gleaned from the EISA cfg files.
- Too bad it doesn't work -- see below.
-
- The ES3210 is an EISA shared memory NS8390 implementation. Note
- that all memory copies to/from the board must be 32bit transfers.
- Which rules out using eth_io_copy_and_sum() in this driver.
-
- Apparently there are two slightly different revisions of the
- card, since there are two distinct EISA cfg files (!rii0101.cfg
- and !rii0102.cfg) One has media select in the cfg file and the
- other doesn't. Hopefully this will work with either.
-
- That is about all I can tell you about it, having never actually
- even seen one of these cards. :) Try http://www.interlan.com
- if you want more info.
-
- Thanks go to Mark Salazar for testing v0.02 of this driver.
-
- Bugs, to-fix, etc:
-
- 1) The EISA cfg ports that are *supposed* to have the IRQ and shared
- mem values just read 0xff all the time. Hrrmpf. Apparently the
- same happens with the packet driver as the code for reading
- these registers is disabled there. In the meantime, boot with:
- ether=<IRQ>,0,0x<shared_mem_addr>,eth0 to override the IRQ and
- shared memory detection. (The i/o port detection is okay.)
-
- 2) Module support currently untested. Probably works though.
-
-*/
-
-static const char version[] =
- "es3210.c: Driver revision v0.03, 14/09/96\n";
-
-#include <linux/module.h>
-#include <linux/eisa.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-
-#include <asm/io.h>
-
-#include "8390.h"
-
-static int es_probe1(struct net_device *dev, int ioaddr);
-
-static void es_reset_8390(struct net_device *dev);
-
-static void es_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page);
-static void es_block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset);
-static void es_block_output(struct net_device *dev, int count, const unsigned char *buf, int start_page);
-
-#define ES_START_PG 0x00 /* First page of TX buffer */
-#define ES_STOP_PG 0x40 /* Last page +1 of RX ring */
-
-#define ES_IO_EXTENT 0x37 /* The cfg file says 0xc90 -> 0xcc7 */
-#define ES_ID_PORT 0xc80 /* Same for all EISA cards */
-#define ES_SA_PROM 0xc90 /* Start of e'net addr. */
-#define ES_RESET_PORT 0xc84 /* From the packet driver source */
-#define ES_NIC_OFFSET 0xca0 /* Hello, the 8390 is *here* */
-
-#define ES_ADDR0 0x02 /* 3 byte vendor prefix */
-#define ES_ADDR1 0x07
-#define ES_ADDR2 0x01
-
-/*
- * Two card revisions. EISA ID's are always rev. minor, rev. major,, and
- * then the three vendor letters stored in 5 bits each, with an "a" = 1.
- * For eg: "rii" = 10010 01001 01001 = 0x4929, which is how the EISA
- * config utility determines automagically what config file(s) to use.
- */
-#define ES_EISA_ID1 0x01012949 /* !rii0101.cfg */
-#define ES_EISA_ID2 0x02012949 /* !rii0102.cfg */
-
-#define ES_CFG1 0xcc0 /* IOPORT(1) --> IOPORT(6) in cfg file */
-#define ES_CFG2 0xcc1
-#define ES_CFG3 0xcc2
-#define ES_CFG4 0xcc3
-#define ES_CFG5 0xcc4
-#define ES_CFG6 0xc84 /* NB: 0xc84 is also "reset" port. */
-
-/*
- * You can OR any of the following bits together and assign it
- * to ES_DEBUG to get verbose driver info during operation.
- * Some of these don't do anything yet.
- */
-
-#define ES_D_PROBE 0x01
-#define ES_D_RX_PKT 0x02
-#define ES_D_TX_PKT 0x04
-#define ED_D_IRQ 0x08
-
-#define ES_DEBUG 0
-
-static unsigned char lo_irq_map[] __initdata = {3, 4, 5, 6, 7, 9, 10};
-static unsigned char hi_irq_map[] __initdata = {11, 12, 0, 14, 0, 0, 0, 15};
-
-/*
- * Probe for the card. The best way is to read the EISA ID if it
- * is known. Then we check the prefix of the station address
- * PROM for a match against the Racal-Interlan assigned value.
- */
-
-static int __init do_es_probe(struct net_device *dev)
-{
- unsigned short ioaddr = dev->base_addr;
- int irq = dev->irq;
- int mem_start = dev->mem_start;
-
- if (ioaddr > 0x1ff) /* Check a single specified location. */
- return es_probe1(dev, ioaddr);
- else if (ioaddr > 0) /* Don't probe at all. */
- return -ENXIO;
-
- if (!EISA_bus) {
-#if ES_DEBUG & ES_D_PROBE
- printk("es3210.c: Not EISA bus. Not probing high ports.\n");
-#endif
- return -ENXIO;
- }
-
- /* EISA spec allows for up to 16 slots, but 8 is typical. */
- for (ioaddr = 0x1000; ioaddr < 0x9000; ioaddr += 0x1000) {
- if (es_probe1(dev, ioaddr) == 0)
- return 0;
- dev->irq = irq;
- dev->mem_start = mem_start;
- }
-
- return -ENODEV;
-}
-
-#ifndef MODULE
-struct net_device * __init es_probe(int unit)
-{
- struct net_device *dev = alloc_ei_netdev();
- int err;
-
- if (!dev)
- return ERR_PTR(-ENOMEM);
-
- sprintf(dev->name, "eth%d", unit);
- netdev_boot_setup_check(dev);
-
- err = do_es_probe(dev);
- if (err)
- goto out;
- return dev;
-out:
- free_netdev(dev);
- return ERR_PTR(err);
-}
-#endif
-
-static int __init es_probe1(struct net_device *dev, int ioaddr)
-{
- int i, retval;
- unsigned long eisa_id;
-
- if (!request_region(ioaddr + ES_SA_PROM, ES_IO_EXTENT, "es3210"))
- return -ENODEV;
-
-#if ES_DEBUG & ES_D_PROBE
- printk("es3210.c: probe at %#x, ID %#8x\n", ioaddr, inl(ioaddr + ES_ID_PORT));
- printk("es3210.c: config regs: %#x %#x %#x %#x %#x %#x\n",
- inb(ioaddr + ES_CFG1), inb(ioaddr + ES_CFG2), inb(ioaddr + ES_CFG3),
- inb(ioaddr + ES_CFG4), inb(ioaddr + ES_CFG5), inb(ioaddr + ES_CFG6));
-#endif
-
-/* Check the EISA ID of the card. */
- eisa_id = inl(ioaddr + ES_ID_PORT);
- if ((eisa_id != ES_EISA_ID1) && (eisa_id != ES_EISA_ID2)) {
- retval = -ENODEV;
- goto out;
- }
-
- for (i = 0; i < ETH_ALEN ; i++)
- dev->dev_addr[i] = inb(ioaddr + ES_SA_PROM + i);
-
-/* Check the Racal vendor ID as well. */
- if (dev->dev_addr[0] != ES_ADDR0 ||
- dev->dev_addr[1] != ES_ADDR1 ||
- dev->dev_addr[2] != ES_ADDR2) {
- printk("es3210.c: card not found %pM (invalid_prefix).\n",
- dev->dev_addr);
- retval = -ENODEV;
- goto out;
- }
-
- printk("es3210.c: ES3210 rev. %ld at %#x, node %pM",
- eisa_id>>24, ioaddr, dev->dev_addr);
-
- /* Snarf the interrupt now. */
- if (dev->irq == 0) {
- unsigned char hi_irq = inb(ioaddr + ES_CFG2) & 0x07;
- unsigned char lo_irq = inb(ioaddr + ES_CFG1) & 0xfe;
-
- if (hi_irq != 0) {
- dev->irq = hi_irq_map[hi_irq - 1];
- } else {
- int i = 0;
- while (lo_irq > (1<<i)) i++;
- dev->irq = lo_irq_map[i];
- }
- printk(" using IRQ %d", dev->irq);
-#if ES_DEBUG & ES_D_PROBE
- printk("es3210.c: hi_irq %#x, lo_irq %#x, dev->irq = %d\n",
- hi_irq, lo_irq, dev->irq);
-#endif
- } else {
- if (dev->irq == 2)
- dev->irq = 9; /* Doh! */
- printk(" assigning IRQ %d", dev->irq);
- }
-
- if (request_irq(dev->irq, ei_interrupt, 0, "es3210", dev)) {
- printk (" unable to get IRQ %d.\n", dev->irq);
- retval = -EAGAIN;
- goto out;
- }
-
- if (dev->mem_start == 0) {
- unsigned char mem_enabled = inb(ioaddr + ES_CFG2) & 0xc0;
- unsigned char mem_bits = inb(ioaddr + ES_CFG3) & 0x07;
-
- if (mem_enabled != 0x80) {
- printk(" shared mem disabled - giving up\n");
- retval = -ENXIO;
- goto out1;
- }
- dev->mem_start = 0xC0000 + mem_bits*0x4000;
- printk(" using ");
- } else {
- printk(" assigning ");
- }
-
- ei_status.mem = ioremap(dev->mem_start, (ES_STOP_PG - ES_START_PG)*256);
- if (!ei_status.mem) {
- printk("ioremap failed - giving up\n");
- retval = -ENXIO;
- goto out1;
- }
-
- dev->mem_end = dev->mem_start + (ES_STOP_PG - ES_START_PG)*256;
-
- printk("mem %#lx-%#lx\n", dev->mem_start, dev->mem_end-1);
-
-#if ES_DEBUG & ES_D_PROBE
- if (inb(ioaddr + ES_CFG5))
- printk("es3210: Warning - DMA channel enabled, but not used here.\n");
-#endif
- /* Note, point at the 8390, and not the card... */
- dev->base_addr = ioaddr + ES_NIC_OFFSET;
-
- ei_status.name = "ES3210";
- ei_status.tx_start_page = ES_START_PG;
- ei_status.rx_start_page = ES_START_PG + TX_PAGES;
- ei_status.stop_page = ES_STOP_PG;
- ei_status.word16 = 1;
-
- if (ei_debug > 0)
- printk(version);
-
- ei_status.reset_8390 = &es_reset_8390;
- ei_status.block_input = &es_block_input;
- ei_status.block_output = &es_block_output;
- ei_status.get_8390_hdr = &es_get_8390_hdr;
-
- dev->netdev_ops = &ei_netdev_ops;
- NS8390_init(dev, 0);
-
- retval = register_netdev(dev);
- if (retval)
- goto out1;
- return 0;
-out1:
- free_irq(dev->irq, dev);
-out:
- release_region(ioaddr + ES_SA_PROM, ES_IO_EXTENT);
- return retval;
-}
-
-/*
- * Reset as per the packet driver method. Judging by the EISA cfg
- * file, this just toggles the "Board Enable" bits (bit 2 and 0).
- */
-
-static void es_reset_8390(struct net_device *dev)
-{
- unsigned short ioaddr = dev->base_addr;
- unsigned long end;
-
- outb(0x04, ioaddr + ES_RESET_PORT);
- if (ei_debug > 1) printk("%s: resetting the ES3210...", dev->name);
-
- end = jiffies + 2*HZ/100;
- while ((signed)(end - jiffies) > 0) continue;
-
- ei_status.txing = 0;
- outb(0x01, ioaddr + ES_RESET_PORT);
- if (ei_debug > 1) printk("reset done\n");
-}
-
-/*
- * Note: In the following three functions is the implicit assumption
- * that the associated memcpy will only use "rep; movsl" as long as
- * we keep the counts as some multiple of doublewords. This is a
- * requirement of the hardware, and also prevents us from using
- * eth_io_copy_and_sum() since we can't guarantee it will limit
- * itself to doubleword access.
- */
-
-/*
- * Grab the 8390 specific header. Similar to the block_input routine, but
- * we don't need to be concerned with ring wrap as the header will be at
- * the start of a page, so we optimize accordingly. (A single doubleword.)
- */
-
-static void
-es_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page)
-{
- void __iomem *hdr_start = ei_status.mem + ((ring_page - ES_START_PG)<<8);
- memcpy_fromio(hdr, hdr_start, sizeof(struct e8390_pkt_hdr));
- hdr->count = (hdr->count + 3) & ~3; /* Round up allocation. */
-}
-
-/*
- * Block input and output are easy on shared memory ethercards, the only
- * complication is when the ring buffer wraps. The count will already
- * be rounded up to a doubleword value via es_get_8390_hdr() above.
- */
-
-static void es_block_input(struct net_device *dev, int count, struct sk_buff *skb,
- int ring_offset)
-{
- void __iomem *xfer_start = ei_status.mem + ring_offset - ES_START_PG*256;
-
- if (ring_offset + count > ES_STOP_PG*256) {
- /* Packet wraps over end of ring buffer. */
- int semi_count = ES_STOP_PG*256 - ring_offset;
- memcpy_fromio(skb->data, xfer_start, semi_count);
- count -= semi_count;
- memcpy_fromio(skb->data + semi_count, ei_status.mem, count);
- } else {
- /* Packet is in one chunk. */
- memcpy_fromio(skb->data, xfer_start, count);
- }
-}
-
-static void es_block_output(struct net_device *dev, int count,
- const unsigned char *buf, int start_page)
-{
- void __iomem *shmem = ei_status.mem + ((start_page - ES_START_PG)<<8);
-
- count = (count + 3) & ~3; /* Round up to doubleword */
- memcpy_toio(shmem, buf, count);
-}
-
-#ifdef MODULE
-#define MAX_ES_CARDS 4 /* Max number of ES3210 cards per module */
-#define NAMELEN 8 /* # of chars for storing dev->name */
-static struct net_device *dev_es3210[MAX_ES_CARDS];
-static int io[MAX_ES_CARDS];
-static int irq[MAX_ES_CARDS];
-static int mem[MAX_ES_CARDS];
-
-module_param_array(io, int, NULL, 0);
-module_param_array(irq, int, NULL, 0);
-module_param_array(mem, int, NULL, 0);
-MODULE_PARM_DESC(io, "I/O base address(es)");
-MODULE_PARM_DESC(irq, "IRQ number(s)");
-MODULE_PARM_DESC(mem, "memory base address(es)");
-MODULE_DESCRIPTION("Racal-Interlan ES3210 EISA ethernet driver");
-MODULE_LICENSE("GPL");
-
-int __init init_module(void)
-{
- struct net_device *dev;
- int this_dev, found = 0;
-
- for (this_dev = 0; this_dev < MAX_ES_CARDS; this_dev++) {
- if (io[this_dev] == 0 && this_dev != 0)
- break;
- dev = alloc_ei_netdev();
- if (!dev)
- break;
- dev->irq = irq[this_dev];
- dev->base_addr = io[this_dev];
- dev->mem_start = mem[this_dev];
- if (do_es_probe(dev) == 0) {
- dev_es3210[found++] = dev;
- continue;
- }
- free_netdev(dev);
- printk(KERN_WARNING "es3210.c: No es3210 card found (i/o = 0x%x).\n", io[this_dev]);
- break;
- }
- if (found)
- return 0;
- return -ENXIO;
-}
-
-static void cleanup_card(struct net_device *dev)
-{
- free_irq(dev->irq, dev);
- release_region(dev->base_addr, ES_IO_EXTENT);
- iounmap(ei_status.mem);
-}
-
-void __exit
-cleanup_module(void)
-{
- int this_dev;
-
- for (this_dev = 0; this_dev < MAX_ES_CARDS; this_dev++) {
- struct net_device *dev = dev_es3210[this_dev];
- if (dev) {
- unregister_netdev(dev);
- cleanup_card(dev);
- free_netdev(dev);
- }
- }
-}
-#endif /* MODULE */
-
diff --git a/drivers/net/ethernet/8390/lne390.c b/drivers/net/ethernet/8390/lne390.c
deleted file mode 100644
index 479409bf2e3c..000000000000
--- a/drivers/net/ethernet/8390/lne390.c
+++ /dev/null
@@ -1,433 +0,0 @@
-/*
- lne390.c
-
- Linux driver for Mylex LNE390 EISA Network Adapter
-
- Copyright (C) 1996-1998, Paul Gortmaker.
-
- This software may be used and distributed according to the terms
- of the GNU General Public License, incorporated herein by reference.
-
- Information and Code Sources:
-
- 1) Based upon framework of es3210 driver.
- 2) The existing myriad of other Linux 8390 drivers by Donald Becker.
- 3) Russ Nelson's asm packet driver provided additional info.
- 4) Info for getting IRQ and sh-mem gleaned from the EISA cfg files.
-
- The LNE390 is an EISA shared memory NS8390 implementation. Note
- that all memory copies to/from the board must be 32bit transfers.
- There are two versions of the card: the lne390a and the lne390b.
- Going by the EISA cfg files, the "a" has jumpers to select between
- BNC/AUI, but the "b" also has RJ-45 and selection is via the SCU.
- The shared memory address selection is also slightly different.
- Note that shared memory address > 1MB are supported with this driver.
-
- You can try <http://www.mylex.com> if you want more info, as I've
- never even seen one of these cards. :)
-
- Arnaldo Carvalho de Melo <acme@conectiva.com.br> - 2000/09/01
- - get rid of check_region
- - no need to check if dev == NULL in lne390_probe1
-*/
-
-static const char *version =
- "lne390.c: Driver revision v0.99.1, 01/09/2000\n";
-
-#include <linux/module.h>
-#include <linux/eisa.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-
-#include <asm/io.h>
-
-#include "8390.h"
-
-#define DRV_NAME "lne390"
-
-static int lne390_probe1(struct net_device *dev, int ioaddr);
-
-static void lne390_reset_8390(struct net_device *dev);
-
-static void lne390_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page);
-static void lne390_block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset);
-static void lne390_block_output(struct net_device *dev, int count, const unsigned char *buf, const int start_page);
-
-#define LNE390_START_PG 0x00 /* First page of TX buffer */
-#define LNE390_STOP_PG 0x80 /* Last page +1 of RX ring */
-
-#define LNE390_ID_PORT 0xc80 /* Same for all EISA cards */
-#define LNE390_IO_EXTENT 0x20
-#define LNE390_SA_PROM 0x16 /* Start of e'net addr. */
-#define LNE390_RESET_PORT 0xc84 /* From the pkt driver source */
-#define LNE390_NIC_OFFSET 0x00 /* Hello, the 8390 is *here* */
-
-#define LNE390_ADDR0 0x00 /* 3 byte vendor prefix */
-#define LNE390_ADDR1 0x80
-#define LNE390_ADDR2 0xe5
-
-#define LNE390_ID0 0x10009835 /* 0x3598 = 01101 01100 11000 = mlx */
-#define LNE390_ID1 0x11009835 /* above is the 390A, this is 390B */
-
-#define LNE390_CFG1 0xc84 /* NB: 0xc84 is also "reset" port. */
-#define LNE390_CFG2 0xc90
-
-/*
- * You can OR any of the following bits together and assign it
- * to LNE390_DEBUG to get verbose driver info during operation.
- * Currently only the probe one is implemented.
- */
-
-#define LNE390_D_PROBE 0x01
-#define LNE390_D_RX_PKT 0x02
-#define LNE390_D_TX_PKT 0x04
-#define LNE390_D_IRQ 0x08
-
-#define LNE390_DEBUG 0
-
-static unsigned char irq_map[] __initdata = {15, 12, 11, 10, 9, 7, 5, 3};
-static unsigned int shmem_mapA[] __initdata = {0xff, 0xfe, 0xfd, 0xfff, 0xffe, 0xffc, 0x0d, 0x0};
-static unsigned int shmem_mapB[] __initdata = {0xff, 0xfe, 0x0e, 0xfff, 0xffe, 0xffc, 0x0d, 0x0};
-
-/*
- * Probe for the card. The best way is to read the EISA ID if it
- * is known. Then we can check the prefix of the station address
- * PROM for a match against the value assigned to Mylex.
- */
-
-static int __init do_lne390_probe(struct net_device *dev)
-{
- unsigned short ioaddr = dev->base_addr;
- int irq = dev->irq;
- int mem_start = dev->mem_start;
- int ret;
-
- if (ioaddr > 0x1ff) { /* Check a single specified location. */
- if (!request_region(ioaddr, LNE390_IO_EXTENT, DRV_NAME))
- return -EBUSY;
- ret = lne390_probe1(dev, ioaddr);
- if (ret)
- release_region(ioaddr, LNE390_IO_EXTENT);
- return ret;
- }
- else if (ioaddr > 0) /* Don't probe at all. */
- return -ENXIO;
-
- if (!EISA_bus) {
-#if LNE390_DEBUG & LNE390_D_PROBE
- printk("lne390-debug: Not an EISA bus. Not probing high ports.\n");
-#endif
- return -ENXIO;
- }
-
- /* EISA spec allows for up to 16 slots, but 8 is typical. */
- for (ioaddr = 0x1000; ioaddr < 0x9000; ioaddr += 0x1000) {
- if (!request_region(ioaddr, LNE390_IO_EXTENT, DRV_NAME))
- continue;
- if (lne390_probe1(dev, ioaddr) == 0)
- return 0;
- release_region(ioaddr, LNE390_IO_EXTENT);
- dev->irq = irq;
- dev->mem_start = mem_start;
- }
-
- return -ENODEV;
-}
-
-#ifndef MODULE
-struct net_device * __init lne390_probe(int unit)
-{
- struct net_device *dev = alloc_ei_netdev();
- int err;
-
- if (!dev)
- return ERR_PTR(-ENOMEM);
-
- sprintf(dev->name, "eth%d", unit);
- netdev_boot_setup_check(dev);
-
- err = do_lne390_probe(dev);
- if (err)
- goto out;
- return dev;
-out:
- free_netdev(dev);
- return ERR_PTR(err);
-}
-#endif
-
-static int __init lne390_probe1(struct net_device *dev, int ioaddr)
-{
- int i, revision, ret;
- unsigned long eisa_id;
-
- if (inb_p(ioaddr + LNE390_ID_PORT) == 0xff) return -ENODEV;
-
-#if LNE390_DEBUG & LNE390_D_PROBE
- printk("lne390-debug: probe at %#x, ID %#8x\n", ioaddr, inl(ioaddr + LNE390_ID_PORT));
- printk("lne390-debug: config regs: %#x %#x\n",
- inb(ioaddr + LNE390_CFG1), inb(ioaddr + LNE390_CFG2));
-#endif
-
-
-/* Check the EISA ID of the card. */
- eisa_id = inl(ioaddr + LNE390_ID_PORT);
- if ((eisa_id != LNE390_ID0) && (eisa_id != LNE390_ID1)) {
- return -ENODEV;
- }
-
- revision = (eisa_id >> 24) & 0x01; /* 0 = rev A, 1 rev B */
-
-#if 0
-/* Check the Mylex vendor ID as well. Not really required. */
- if (inb(ioaddr + LNE390_SA_PROM + 0) != LNE390_ADDR0
- || inb(ioaddr + LNE390_SA_PROM + 1) != LNE390_ADDR1
- || inb(ioaddr + LNE390_SA_PROM + 2) != LNE390_ADDR2 ) {
- printk("lne390.c: card not found");
- for (i = 0; i < ETH_ALEN; i++)
- printk(" %02x", inb(ioaddr + LNE390_SA_PROM + i));
- printk(" (invalid prefix).\n");
- return -ENODEV;
- }
-#endif
-
- for (i = 0; i < ETH_ALEN; i++)
- dev->dev_addr[i] = inb(ioaddr + LNE390_SA_PROM + i);
- printk("lne390.c: LNE390%X in EISA slot %d, address %pM.\n",
- 0xa+revision, ioaddr/0x1000, dev->dev_addr);
-
- printk("lne390.c: ");
-
- /* Snarf the interrupt now. CFG file has them all listed as `edge' with share=NO */
- if (dev->irq == 0) {
- unsigned char irq_reg = inb(ioaddr + LNE390_CFG2) >> 3;
- dev->irq = irq_map[irq_reg & 0x07];
- printk("using");
- } else {
- /* This is useless unless we reprogram the card here too */
- if (dev->irq == 2) dev->irq = 9; /* Doh! */
- printk("assigning");
- }
- printk(" IRQ %d,", dev->irq);
-
- if ((ret = request_irq(dev->irq, ei_interrupt, 0, DRV_NAME, dev))) {
- printk (" unable to get IRQ %d.\n", dev->irq);
- return ret;
- }
-
- if (dev->mem_start == 0) {
- unsigned char mem_reg = inb(ioaddr + LNE390_CFG2) & 0x07;
-
- if (revision) /* LNE390B */
- dev->mem_start = shmem_mapB[mem_reg] * 0x10000;
- else /* LNE390A */
- dev->mem_start = shmem_mapA[mem_reg] * 0x10000;
- printk(" using ");
- } else {
- /* Should check for value in shmem_map and reprogram the card to use it */
- dev->mem_start &= 0xfff0000;
- printk(" assigning ");
- }
-
- printk("%dkB memory at physical address %#lx\n",
- LNE390_STOP_PG/4, dev->mem_start);
-
- /*
- BEWARE!! Some dain-bramaged EISA SCUs will allow you to put
- the card mem within the region covered by `normal' RAM !!!
-
- ioremap() will fail in that case.
- */
- ei_status.mem = ioremap(dev->mem_start, LNE390_STOP_PG*0x100);
- if (!ei_status.mem) {
- printk(KERN_ERR "lne390.c: Unable to remap card memory above 1MB !!\n");
- printk(KERN_ERR "lne390.c: Try using EISA SCU to set memory below 1MB.\n");
- printk(KERN_ERR "lne390.c: Driver NOT installed.\n");
- ret = -EAGAIN;
- goto cleanup;
- }
- printk("lne390.c: remapped %dkB card memory to virtual address %p\n",
- LNE390_STOP_PG/4, ei_status.mem);
-
- dev->mem_start = (unsigned long)ei_status.mem;
- dev->mem_end = dev->mem_start + (LNE390_STOP_PG - LNE390_START_PG)*256;
-
- /* The 8390 offset is zero for the LNE390 */
- dev->base_addr = ioaddr;
-
- ei_status.name = "LNE390";
- ei_status.tx_start_page = LNE390_START_PG;
- ei_status.rx_start_page = LNE390_START_PG + TX_PAGES;
- ei_status.stop_page = LNE390_STOP_PG;
- ei_status.word16 = 1;
-
- if (ei_debug > 0)
- printk(version);
-
- ei_status.reset_8390 = &lne390_reset_8390;
- ei_status.block_input = &lne390_block_input;
- ei_status.block_output = &lne390_block_output;
- ei_status.get_8390_hdr = &lne390_get_8390_hdr;
-
- dev->netdev_ops = &ei_netdev_ops;
- NS8390_init(dev, 0);
-
- ret = register_netdev(dev);
- if (ret)
- goto unmap;
- return 0;
-unmap:
- if (ei_status.reg0)
- iounmap(ei_status.mem);
-cleanup:
- free_irq(dev->irq, dev);
- return ret;
-}
-
-/*
- * Reset as per the packet driver method. Judging by the EISA cfg
- * file, this just toggles the "Board Enable" bits (bit 2 and 0).
- */
-
-static void lne390_reset_8390(struct net_device *dev)
-{
- unsigned short ioaddr = dev->base_addr;
-
- outb(0x04, ioaddr + LNE390_RESET_PORT);
- if (ei_debug > 1) printk("%s: resetting the LNE390...", dev->name);
-
- mdelay(2);
-
- ei_status.txing = 0;
- outb(0x01, ioaddr + LNE390_RESET_PORT);
- if (ei_debug > 1) printk("reset done\n");
-}
-
-/*
- * Note: In the following three functions is the implicit assumption
- * that the associated memcpy will only use "rep; movsl" as long as
- * we keep the counts as some multiple of doublewords. This is a
- * requirement of the hardware, and also prevents us from using
- * eth_io_copy_and_sum() since we can't guarantee it will limit
- * itself to doubleword access.
- */
-
-/*
- * Grab the 8390 specific header. Similar to the block_input routine, but
- * we don't need to be concerned with ring wrap as the header will be at
- * the start of a page, so we optimize accordingly. (A single doubleword.)
- */
-
-static void
-lne390_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page)
-{
- void __iomem *hdr_start = ei_status.mem + ((ring_page - LNE390_START_PG)<<8);
- memcpy_fromio(hdr, hdr_start, sizeof(struct e8390_pkt_hdr));
- hdr->count = (hdr->count + 3) & ~3; /* Round up allocation. */
-}
-
-/*
- * Block input and output are easy on shared memory ethercards, the only
- * complication is when the ring buffer wraps. The count will already
- * be rounded up to a doubleword value via lne390_get_8390_hdr() above.
- */
-
-static void lne390_block_input(struct net_device *dev, int count, struct sk_buff *skb,
- int ring_offset)
-{
- void __iomem *xfer_start = ei_status.mem + ring_offset - (LNE390_START_PG<<8);
-
- if (ring_offset + count > (LNE390_STOP_PG<<8)) {
- /* Packet wraps over end of ring buffer. */
- int semi_count = (LNE390_STOP_PG<<8) - ring_offset;
- memcpy_fromio(skb->data, xfer_start, semi_count);
- count -= semi_count;
- memcpy_fromio(skb->data + semi_count,
- ei_status.mem + (TX_PAGES<<8), count);
- } else {
- /* Packet is in one chunk. */
- memcpy_fromio(skb->data, xfer_start, count);
- }
-}
-
-static void lne390_block_output(struct net_device *dev, int count,
- const unsigned char *buf, int start_page)
-{
- void __iomem *shmem = ei_status.mem + ((start_page - LNE390_START_PG)<<8);
-
- count = (count + 3) & ~3; /* Round up to doubleword */
- memcpy_toio(shmem, buf, count);
-}
-
-
-#ifdef MODULE
-#define MAX_LNE_CARDS 4 /* Max number of LNE390 cards per module */
-static struct net_device *dev_lne[MAX_LNE_CARDS];
-static int io[MAX_LNE_CARDS];
-static int irq[MAX_LNE_CARDS];
-static int mem[MAX_LNE_CARDS];
-
-module_param_array(io, int, NULL, 0);
-module_param_array(irq, int, NULL, 0);
-module_param_array(mem, int, NULL, 0);
-MODULE_PARM_DESC(io, "I/O base address(es)");
-MODULE_PARM_DESC(irq, "IRQ number(s)");
-MODULE_PARM_DESC(mem, "memory base address(es)");
-MODULE_DESCRIPTION("Mylex LNE390A/B EISA Ethernet driver");
-MODULE_LICENSE("GPL");
-
-int __init init_module(void)
-{
- struct net_device *dev;
- int this_dev, found = 0;
-
- for (this_dev = 0; this_dev < MAX_LNE_CARDS; this_dev++) {
- if (io[this_dev] == 0 && this_dev != 0)
- break;
- dev = alloc_ei_netdev();
- if (!dev)
- break;
- dev->irq = irq[this_dev];
- dev->base_addr = io[this_dev];
- dev->mem_start = mem[this_dev];
- if (do_lne390_probe(dev) == 0) {
- dev_lne[found++] = dev;
- continue;
- }
- free_netdev(dev);
- printk(KERN_WARNING "lne390.c: No LNE390 card found (i/o = 0x%x).\n", io[this_dev]);
- break;
- }
- if (found)
- return 0;
- return -ENXIO;
-}
-
-static void cleanup_card(struct net_device *dev)
-{
- free_irq(dev->irq, dev);
- release_region(dev->base_addr, LNE390_IO_EXTENT);
- iounmap(ei_status.mem);
-}
-
-void __exit cleanup_module(void)
-{
- int this_dev;
-
- for (this_dev = 0; this_dev < MAX_LNE_CARDS; this_dev++) {
- struct net_device *dev = dev_lne[this_dev];
- if (dev) {
- unregister_netdev(dev);
- cleanup_card(dev);
- free_netdev(dev);
- }
- }
-}
-#endif /* MODULE */
-
diff --git a/drivers/net/ethernet/8390/ne3210.c b/drivers/net/ethernet/8390/ne3210.c
deleted file mode 100644
index ebcdb52ec739..000000000000
--- a/drivers/net/ethernet/8390/ne3210.c
+++ /dev/null
@@ -1,346 +0,0 @@
-/*
- ne3210.c
-
- Linux driver for Novell NE3210 EISA Network Adapter
-
- Copyright (C) 1998, Paul Gortmaker.
-
- This software may be used and distributed according to the terms
- of the GNU General Public License, incorporated herein by reference.
-
- Information and Code Sources:
-
- 1) Based upon my other EISA 8390 drivers (lne390, es3210, smc-ultra32)
- 2) The existing myriad of other Linux 8390 drivers by Donald Becker.
- 3) Info for getting IRQ and sh-mem gleaned from the EISA cfg file
-
- The NE3210 is an EISA shared memory NS8390 implementation. Shared
- memory address > 1MB should work with this driver.
-
- Note that the .cfg file (3/11/93, v1.0) has AUI and BNC switched
- around (or perhaps there are some defective/backwards cards ???)
-
- This driver WILL NOT WORK FOR THE NE3200 - it is completely different
- and does not use an 8390 at all.
-
- Updated to EISA probing API 5/2003 by Marc Zyngier.
-*/
-
-#include <linux/module.h>
-#include <linux/eisa.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/delay.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-#include <linux/mm.h>
-
-#include <asm/io.h>
-
-#include "8390.h"
-
-#define DRV_NAME "ne3210"
-
-static void ne3210_reset_8390(struct net_device *dev);
-
-static void ne3210_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page);
-static void ne3210_block_input(struct net_device *dev, int count, struct sk_buff *skb, int ring_offset);
-static void ne3210_block_output(struct net_device *dev, int count, const unsigned char *buf, const int start_page);
-
-#define NE3210_START_PG 0x00 /* First page of TX buffer */
-#define NE3210_STOP_PG 0x80 /* Last page +1 of RX ring */
-
-#define NE3210_IO_EXTENT 0x20
-#define NE3210_SA_PROM 0x16 /* Start of e'net addr. */
-#define NE3210_RESET_PORT 0xc84
-#define NE3210_NIC_OFFSET 0x00 /* Hello, the 8390 is *here* */
-
-#define NE3210_ADDR0 0x00 /* 3 byte vendor prefix */
-#define NE3210_ADDR1 0x00
-#define NE3210_ADDR2 0x1b
-
-#define NE3210_CFG1 0xc84 /* NB: 0xc84 is also "reset" port. */
-#define NE3210_CFG2 0xc90
-#define NE3210_CFG_EXTENT (NE3210_CFG2 - NE3210_CFG1 + 1)
-
-/*
- * You can OR any of the following bits together and assign it
- * to NE3210_DEBUG to get verbose driver info during operation.
- * Currently only the probe one is implemented.
- */
-
-#define NE3210_D_PROBE 0x01
-#define NE3210_D_RX_PKT 0x02
-#define NE3210_D_TX_PKT 0x04
-#define NE3210_D_IRQ 0x08
-
-#define NE3210_DEBUG 0x0
-
-static unsigned char irq_map[] __initdata = {15, 12, 11, 10, 9, 7, 5, 3};
-static unsigned int shmem_map[] __initdata = {0xff0, 0xfe0, 0xfff0, 0xd8, 0xffe0, 0xffc0, 0xd0, 0x0};
-static const char * const ifmap[] __initconst = {"UTP", "?", "BNC", "AUI"};
-static int ifmap_val[] __initdata = {
- IF_PORT_10BASET,
- IF_PORT_UNKNOWN,
- IF_PORT_10BASE2,
- IF_PORT_AUI,
-};
-
-static int __init ne3210_eisa_probe (struct device *device)
-{
- unsigned long ioaddr, phys_mem;
- int i, retval, port_index;
- struct eisa_device *edev = to_eisa_device (device);
- struct net_device *dev;
-
- /* Allocate dev->priv and fill in 8390 specific dev fields. */
- if (!(dev = alloc_ei_netdev ())) {
- printk ("ne3210.c: unable to allocate memory for dev!\n");
- return -ENOMEM;
- }
-
- SET_NETDEV_DEV(dev, device);
- dev_set_drvdata(device, dev);
- ioaddr = edev->base_addr;
-
- if (!request_region(ioaddr, NE3210_IO_EXTENT, DRV_NAME)) {
- retval = -EBUSY;
- goto out;
- }
-
- if (!request_region(ioaddr + NE3210_CFG1,
- NE3210_CFG_EXTENT, DRV_NAME)) {
- retval = -EBUSY;
- goto out1;
- }
-
-#if NE3210_DEBUG & NE3210_D_PROBE
- printk("ne3210-debug: probe at %#x, ID %s\n", ioaddr, edev->id.sig);
- printk("ne3210-debug: config regs: %#x %#x\n",
- inb(ioaddr + NE3210_CFG1), inb(ioaddr + NE3210_CFG2));
-#endif
-
- port_index = inb(ioaddr + NE3210_CFG2) >> 6;
- for (i = 0; i < ETH_ALEN; i++)
- dev->dev_addr[i] = inb(ioaddr + NE3210_SA_PROM + i);
- printk("ne3210.c: NE3210 in EISA slot %d, media: %s, addr: %pM.\n",
- edev->slot, ifmap[port_index], dev->dev_addr);
-
- /* Snarf the interrupt now. CFG file has them all listed as `edge' with share=NO */
- dev->irq = irq_map[(inb(ioaddr + NE3210_CFG2) >> 3) & 0x07];
- printk("ne3210.c: using IRQ %d, ", dev->irq);
-
- retval = request_irq(dev->irq, ei_interrupt, 0, DRV_NAME, dev);
- if (retval) {
- printk (" unable to get IRQ %d.\n", dev->irq);
- goto out2;
- }
-
- phys_mem = shmem_map[inb(ioaddr + NE3210_CFG2) & 0x07] * 0x1000;
-
- /*
- BEWARE!! Some dain-bramaged EISA SCUs will allow you to put
- the card mem within the region covered by `normal' RAM !!!
- */
- if (phys_mem > 1024*1024) { /* phys addr > 1MB */
- if (phys_mem < virt_to_phys(high_memory)) {
- printk(KERN_CRIT "ne3210.c: Card RAM overlaps with normal memory!!!\n");
- printk(KERN_CRIT "ne3210.c: Use EISA SCU to set card memory below 1MB,\n");
- printk(KERN_CRIT "ne3210.c: or to an address above 0x%llx.\n",
- (u64)virt_to_phys(high_memory));
- printk(KERN_CRIT "ne3210.c: Driver NOT installed.\n");
- retval = -EINVAL;
- goto out3;
- }
- }
-
- if (!request_mem_region (phys_mem, NE3210_STOP_PG*0x100, DRV_NAME)) {
- printk ("ne3210.c: Unable to request shared memory at physical address %#lx\n",
- phys_mem);
- goto out3;
- }
-
- printk("%dkB memory at physical address %#lx\n",
- NE3210_STOP_PG/4, phys_mem);
-
- ei_status.mem = ioremap(phys_mem, NE3210_STOP_PG*0x100);
- if (!ei_status.mem) {
- printk(KERN_ERR "ne3210.c: Unable to remap card memory !!\n");
- printk(KERN_ERR "ne3210.c: Driver NOT installed.\n");
- retval = -EAGAIN;
- goto out4;
- }
- printk("ne3210.c: remapped %dkB card memory to virtual address %p\n",
- NE3210_STOP_PG/4, ei_status.mem);
- dev->mem_start = (unsigned long)ei_status.mem;
- dev->mem_end = dev->mem_start + (NE3210_STOP_PG - NE3210_START_PG)*256;
-
- /* The 8390 offset is zero for the NE3210 */
- dev->base_addr = ioaddr;
-
- ei_status.name = "NE3210";
- ei_status.tx_start_page = NE3210_START_PG;
- ei_status.rx_start_page = NE3210_START_PG + TX_PAGES;
- ei_status.stop_page = NE3210_STOP_PG;
- ei_status.word16 = 1;
- ei_status.priv = phys_mem;
-
- if (ei_debug > 0)
- printk("ne3210 loaded.\n");
-
- ei_status.reset_8390 = &ne3210_reset_8390;
- ei_status.block_input = &ne3210_block_input;
- ei_status.block_output = &ne3210_block_output;
- ei_status.get_8390_hdr = &ne3210_get_8390_hdr;
-
- dev->netdev_ops = &ei_netdev_ops;
-
- dev->if_port = ifmap_val[port_index];
-
- if ((retval = register_netdev (dev)))
- goto out5;
-
- NS8390_init(dev, 0);
- return 0;
-
- out5:
- iounmap(ei_status.mem);
- out4:
- release_mem_region (phys_mem, NE3210_STOP_PG*0x100);
- out3:
- free_irq (dev->irq, dev);
- out2:
- release_region (ioaddr + NE3210_CFG1, NE3210_CFG_EXTENT);
- out1:
- release_region (ioaddr, NE3210_IO_EXTENT);
- out:
- free_netdev (dev);
-
- return retval;
-}
-
-static int ne3210_eisa_remove(struct device *device)
-{
- struct net_device *dev = dev_get_drvdata(device);
- unsigned long ioaddr = to_eisa_device (device)->base_addr;
-
- unregister_netdev (dev);
- iounmap(ei_status.mem);
- release_mem_region (ei_status.priv, NE3210_STOP_PG*0x100);
- free_irq (dev->irq, dev);
- release_region (ioaddr + NE3210_CFG1, NE3210_CFG_EXTENT);
- release_region (ioaddr, NE3210_IO_EXTENT);
- free_netdev (dev);
-
- return 0;
-}
-
-/*
- * Reset by toggling the "Board Enable" bits (bit 2 and 0).
- */
-
-static void ne3210_reset_8390(struct net_device *dev)
-{
- unsigned short ioaddr = dev->base_addr;
-
- outb(0x04, ioaddr + NE3210_RESET_PORT);
- if (ei_debug > 1) printk("%s: resetting the NE3210...", dev->name);
-
- mdelay(2);
-
- ei_status.txing = 0;
- outb(0x01, ioaddr + NE3210_RESET_PORT);
- if (ei_debug > 1) printk("reset done\n");
-}
-
-/*
- * Note: In the following three functions is the implicit assumption
- * that the associated memcpy will only use "rep; movsl" as long as
- * we keep the counts as some multiple of doublewords. This is a
- * requirement of the hardware, and also prevents us from using
- * eth_io_copy_and_sum() since we can't guarantee it will limit
- * itself to doubleword access.
- */
-
-/*
- * Grab the 8390 specific header. Similar to the block_input routine, but
- * we don't need to be concerned with ring wrap as the header will be at
- * the start of a page, so we optimize accordingly. (A single doubleword.)
- */
-
-static void
-ne3210_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr, int ring_page)
-{
- void __iomem *hdr_start = ei_status.mem + ((ring_page - NE3210_START_PG)<<8);
- memcpy_fromio(hdr, hdr_start, sizeof(struct e8390_pkt_hdr));
- hdr->count = (hdr->count + 3) & ~3; /* Round up allocation. */
-}
-
-/*
- * Block input and output are easy on shared memory ethercards, the only
- * complication is when the ring buffer wraps. The count will already
- * be rounded up to a doubleword value via ne3210_get_8390_hdr() above.
- */
-
-static void ne3210_block_input(struct net_device *dev, int count, struct sk_buff *skb,
- int ring_offset)
-{
- void __iomem *start = ei_status.mem + ring_offset - NE3210_START_PG*256;
-
- if (ring_offset + count > NE3210_STOP_PG*256) {
- /* Packet wraps over end of ring buffer. */
- int semi_count = NE3210_STOP_PG*256 - ring_offset;
- memcpy_fromio(skb->data, start, semi_count);
- count -= semi_count;
- memcpy_fromio(skb->data + semi_count,
- ei_status.mem + TX_PAGES*256, count);
- } else {
- /* Packet is in one chunk. */
- memcpy_fromio(skb->data, start, count);
- }
-}
-
-static void ne3210_block_output(struct net_device *dev, int count,
- const unsigned char *buf, int start_page)
-{
- void __iomem *shmem = ei_status.mem + ((start_page - NE3210_START_PG)<<8);
-
- count = (count + 3) & ~3; /* Round up to doubleword */
- memcpy_toio(shmem, buf, count);
-}
-
-static struct eisa_device_id ne3210_ids[] = {
- { "EGL0101" },
- { "NVL1801" },
- { "" },
-};
-MODULE_DEVICE_TABLE(eisa, ne3210_ids);
-
-static struct eisa_driver ne3210_eisa_driver = {
- .id_table = ne3210_ids,
- .driver = {
- .name = "ne3210",
- .probe = ne3210_eisa_probe,
- .remove = ne3210_eisa_remove,
- },
-};
-
-MODULE_DESCRIPTION("NE3210 EISA Ethernet driver");
-MODULE_LICENSE("GPL");
-MODULE_DEVICE_TABLE(eisa, ne3210_ids);
-
-static int ne3210_init(void)
-{
- return eisa_driver_register (&ne3210_eisa_driver);
-}
-
-static void ne3210_cleanup(void)
-{
- eisa_driver_unregister (&ne3210_eisa_driver);
-}
-
-module_init (ne3210_init);
-module_exit (ne3210_cleanup);
diff --git a/drivers/net/ethernet/8390/smc-ultra32.c b/drivers/net/ethernet/8390/smc-ultra32.c
deleted file mode 100644
index 923e42aedcfd..000000000000
--- a/drivers/net/ethernet/8390/smc-ultra32.c
+++ /dev/null
@@ -1,463 +0,0 @@
-/* smc-ultra32.c: An SMC Ultra32 EISA ethernet driver for linux.
-
-Sources:
-
- This driver is based on (cloned from) the ISA SMC Ultra driver
- written by Donald Becker. Modifications to support the EISA
- version of the card by Paul Gortmaker and Leonard N. Zubkoff.
-
- This software may be used and distributed according to the terms
- of the GNU General Public License, incorporated herein by reference.
-
-Theory of Operation:
-
- The SMC Ultra32C card uses the SMC 83c790 chip which is also
- found on the ISA SMC Ultra cards. It has a shared memory mode of
- operation that makes it similar to the ISA version of the card.
- The main difference is that the EISA card has 32KB of RAM, but
- only an 8KB window into that memory. The EISA card also can be
- set for a bus-mastering mode of operation via the ECU, but that
- is not (and probably will never be) supported by this driver.
- The ECU should be run to enable shared memory and to disable the
- bus-mastering feature for use with linux.
-
- By programming the 8390 to use only 8KB RAM, the modifications
- to the ISA driver can be limited to the probe and initialization
- code. This allows easy integration of EISA support into the ISA
- driver. However, the driver development kit from SMC provided the
- register information for sliding the 8KB window, and hence the 8390
- is programmed to use the full 32KB RAM.
-
- Unfortunately this required code changes outside the probe/init
- routines, and thus we decided to separate the EISA driver from
- the ISA one. In this way, ISA users don't end up with a larger
- driver due to the EISA code, and EISA users don't end up with a
- larger driver due to the ISA EtherEZ PIO code. The driver is
- similar to the 3c503/16 driver, in that the window must be set
- back to the 1st 8KB of space for access to the two 8390 Tx slots.
-
- In testing, using only 8KB RAM (3 Tx / 5 Rx) didn't appear to
- be a limiting factor, since the EISA bus could get packets off
- the card fast enough, but having the use of lots of RAM as Rx
- space is extra insurance if interrupt latencies become excessive.
-
-*/
-
-static const char *version = "smc-ultra32.c: 06/97 v1.00\n";
-
-
-#include <linux/module.h>
-#include <linux/eisa.h>
-#include <linux/kernel.h>
-#include <linux/errno.h>
-#include <linux/string.h>
-#include <linux/init.h>
-#include <linux/interrupt.h>
-#include <linux/netdevice.h>
-#include <linux/etherdevice.h>
-
-#include <asm/io.h>
-
-#include "8390.h"
-
-#define DRV_NAME "smc-ultra32"
-
-static int ultra32_probe1(struct net_device *dev, int ioaddr);
-static int ultra32_open(struct net_device *dev);
-static void ultra32_reset_8390(struct net_device *dev);
-static void ultra32_get_8390_hdr(struct net_device *dev, struct e8390_pkt_hdr *hdr,
- int ring_page);
-static void ultra32_block_input(struct net_device *dev, int count,
- struct sk_buff *skb, int ring_offset);
-static void ultra32_block_output(struct net_device *dev, int count,
- const unsigned char *buf,
- const int start_page);
-static int ultra32_close(struct net_device *dev);
-
-#define ULTRA32_CMDREG 0 /* Offset to ASIC command register. */
-#define ULTRA32_RESET 0x80 /* Board reset, in ULTRA32_CMDREG. */
-#define ULTRA32_MEMENB 0x40 /* Enable the shared memory. */
-#define ULTRA32_NIC_OFFSET 16 /* NIC register offset from the base_addr. */
-#define ULTRA32_IO_EXTENT 32
-#define EN0_ERWCNT 0x08 /* Early receive warning count. */
-
-/*
- * Defines that apply only to the Ultra32 EISA card. Note that
- * "smc" = 10011 01101 00011 = 0x4da3, and hence !smc8010.cfg translates
- * into an EISA ID of 0x1080A34D
- */
-#define ULTRA32_BASE 0xca0
-#define ULTRA32_ID 0x1080a34d
-#define ULTRA32_IDPORT (-0x20) /* 0xc80 */
-/* Config regs 1->7 from the EISA !SMC8010.CFG file. */
-#define ULTRA32_CFG1 0x04 /* 0xca4 */
-#define ULTRA32_CFG2 0x05 /* 0xca5 */
-#define ULTRA32_CFG3 (-0x18) /* 0xc88 */
-#define ULTRA32_CFG4 (-0x17) /* 0xc89 */
-#define ULTRA32_CFG5 (-0x16) /* 0xc8a */
-#define ULTRA32_CFG6 (-0x15) /* 0xc8b */
-#define ULTRA32_CFG7 0x0d /* 0xcad */
-
-static void cleanup_card(struct net_device *dev)
-{
- int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET;
- /* NB: ultra32_close_card() does free_irq */
- release_region(ioaddr, ULTRA32_IO_EXTENT);
- iounmap(ei_status.mem);
-}
-
-/* Probe for the Ultra32. This looks like a 8013 with the station
- address PROM at I/O ports <base>+8 to <base>+13, with a checksum
- following.
-*/
-
-struct net_device * __init ultra32_probe(int unit)
-{
- struct net_device *dev;
- int base;
- int irq;
- int err = -ENODEV;
-
- if (!EISA_bus)
- return ERR_PTR(-ENODEV);
-
- dev = alloc_ei_netdev();
-
- if (!dev)
- return ERR_PTR(-ENOMEM);
-
- if (unit >= 0) {
- sprintf(dev->name, "eth%d", unit);
- netdev_boot_setup_check(dev);
- }
-
- irq = dev->irq;
-
- /* EISA spec allows for up to 16 slots, but 8 is typical. */
- for (base = 0x1000 + ULTRA32_BASE; base < 0x9000; base += 0x1000) {
- if (ultra32_probe1(dev, base) == 0)
- break;
- dev->irq = irq;
- }
- if (base >= 0x9000)
- goto out;
- err = register_netdev(dev);
- if (err)
- goto out1;
- return dev;
-out1:
- cleanup_card(dev);
-out:
- free_netdev(dev);
- return ERR_PTR(err);
-}
-
-
-static const struct net_device_ops ultra32_netdev_ops = {
- .ndo_open = ultra32_open,
- .ndo_stop = ultra32_close,
- .ndo_start_xmit = ei_start_xmit,
- .ndo_tx_timeout = ei_tx_timeout,
- .ndo_get_stats = ei_get_stats,
- .ndo_set_rx_mode = ei_set_multicast_list,
- .ndo_validate_addr = eth_validate_addr,
- .ndo_set_mac_address = eth_mac_addr,
- .ndo_change_mtu = eth_change_mtu,
-#ifdef CONFIG_NET_POLL_CONTROLLER
- .ndo_poll_controller = ei_poll,
-#endif
-};
-
-static int __init ultra32_probe1(struct net_device *dev, int ioaddr)
-{
- int i, edge, media, retval;
- int checksum = 0;
- const char *model_name;
- static unsigned version_printed;
- /* Values from various config regs. */
- unsigned char idreg;
- unsigned char reg4;
- const char *ifmap[] = {"UTP No Link", "", "UTP/AUI", "UTP/BNC"};
-
- if (!request_region(ioaddr, ULTRA32_IO_EXTENT, DRV_NAME))
- return -EBUSY;
-
- if (inb(ioaddr + ULTRA32_IDPORT) == 0xff ||
- inl(ioaddr + ULTRA32_IDPORT) != ULTRA32_ID) {
- retval = -ENODEV;
- goto out;
- }
-
- media = inb(ioaddr + ULTRA32_CFG7) & 0x03;
- edge = inb(ioaddr + ULTRA32_CFG5) & 0x08;
- printk("SMC Ultra32 in EISA Slot %d, Media: %s, %s IRQs.\n",
- ioaddr >> 12, ifmap[media],
- (edge ? "Edge Triggered" : "Level Sensitive"));
-
- idreg = inb(ioaddr + 7);
- reg4 = inb(ioaddr + 4) & 0x7f;
-
- /* Check the ID nibble. */
- if ((idreg & 0xf0) != 0x20) { /* SMC Ultra */
- retval = -ENODEV;
- goto out;
- }
-
- /* Select the station address register set. */
- outb(reg4, ioaddr + 4);
-
- for (i = 0; i < 8; i++)
- checksum += inb(ioaddr + 8 + i);
- if ((checksum & 0xff) != 0xff) {
- retval = -ENODEV;
- goto out;
- }
-
- if (ei_debug && version_printed++ == 0)
- printk(version);
-
- model_name = "SMC Ultra32";
-
- for (i = 0; i < 6; i++)
- dev->dev_addr[i] = inb(ioaddr + 8 + i);
-
- printk("%s: %s at 0x%X, %pM",
- dev->name, model_name, ioaddr, dev->dev_addr);
-
- /* Switch from the station address to the alternate register set and
- read the useful registers there. */
- outb(0x80 | reg4, ioaddr + 4);
-
- /* Enable FINE16 mode to avoid BIOS ROM width mismatches @ reboot. */
- outb(0x80 | inb(ioaddr + 0x0c), ioaddr + 0x0c);
-
- /* Reset RAM addr. */
- outb(0x00, ioaddr + 0x0b);
-
- /* Switch back to the station address register set so that the
- MS-DOS driver can find the card after a warm boot. */
- outb(reg4, ioaddr + 4);
-
- if ((inb(ioaddr + ULTRA32_CFG5) & 0x40) == 0) {
- printk("\nsmc-ultra32: Card RAM is disabled! "
- "Run EISA config utility.\n");
- retval = -ENODEV;
- goto out;
- }
- if ((inb(ioaddr + ULTRA32_CFG2) & 0x04) == 0)
- printk("\nsmc-ultra32: Ignoring Bus-Master enable bit. "
- "Run EISA config utility.\n");
-
- if (dev->irq < 2) {
- unsigned char irqmap[] = {0, 9, 3, 5, 7, 10, 11, 15};
- int irq = irqmap[inb(ioaddr + ULTRA32_CFG5) & 0x07];
- if (irq == 0) {
- printk(", failed to detect IRQ line.\n");
- retval = -EAGAIN;
- goto out;
- }
- dev->irq = irq;
- }
-
- /* The 8390 isn't at the base address, so fake the offset */
- dev->base_addr = ioaddr + ULTRA32_NIC_OFFSET;
-
- /* Save RAM address in the unused reg0 to avoid excess inb's. */
- ei_status.reg0 = inb(ioaddr + ULTRA32_CFG3) & 0xfc;
-
- dev->mem_start = 0xc0000 + ((ei_status.reg0 & 0x7c) << 11);
-
- ei_status.name = model_name;
- ei_status.word16 = 1;
- ei_status.tx_start_page = 0;
- ei_status.rx_start_page = TX_PAGES;
- /* All Ultra32 cards have 32KB memory with an 8KB window. */
- ei_status.stop_page = 128;
-
- ei_status.mem = ioremap(dev->mem_start, 0x2000);
- if (!ei_status.mem) {
- printk(", failed to ioremap.\n");
- retval = -ENOMEM;
- goto out;
- }
- dev->mem_end = dev->mem_start + 0x1fff;
-
- printk(", IRQ %d, 32KB memory, 8KB window at 0x%lx-0x%lx.\n",
- dev->irq, dev->mem_start, dev->mem_end);
- ei_status.block_input = &ultra32_block_input;
- ei_status.block_output = &ultra32_block_output;
- ei_status.get_8390_hdr = &ultra32_get_8390_hdr;
- ei_status.reset_8390 = &ultra32_reset_8390;
-
- dev->netdev_ops = &ultra32_netdev_ops;
- NS8390_init(dev, 0);
-
- return 0;
-out:
- release_region(ioaddr, ULTRA32_IO_EXTENT);
- return retval;
-}
-
-static int ultra32_open(struct net_device *dev)
-{
- int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; /* ASIC addr */
- int irq_flags = (inb(ioaddr + ULTRA32_CFG5) & 0x08) ? 0 : IRQF_SHARED;
- int retval;
-
- retval = request_irq(dev->irq, ei_interrupt, irq_flags, dev->name, dev);
- if (retval)
- return retval;
-
- outb(ULTRA32_MEMENB, ioaddr); /* Enable Shared Memory. */
- outb(0x80, ioaddr + ULTRA32_CFG6); /* Enable Interrupts. */
- outb(0x84, ioaddr + 5); /* Enable MEM16 & Disable Bus Master. */
- outb(0x01, ioaddr + 6); /* Enable Interrupts. */
- /* Set the early receive warning level in window 0 high enough not
- to receive ERW interrupts. */
- outb_p(E8390_NODMA+E8390_PAGE0, dev->base_addr);
- outb(0xff, dev->base_addr + EN0_ERWCNT);
- ei_open(dev);
- return 0;
-}
-
-static int ultra32_close(struct net_device *dev)
-{
- int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; /* CMDREG */
-
- netif_stop_queue(dev);
-
- if (ei_debug > 1)
- printk("%s: Shutting down ethercard.\n", dev->name);
-
- outb(0x00, ioaddr + ULTRA32_CFG6); /* Disable Interrupts. */
- outb(0x00, ioaddr + 6); /* Disable interrupts. */
- free_irq(dev->irq, dev);
-
- NS8390_init(dev, 0);
-
- return 0;
-}
-
-static void ultra32_reset_8390(struct net_device *dev)
-{
- int ioaddr = dev->base_addr - ULTRA32_NIC_OFFSET; /* ASIC base addr */
-
- outb(ULTRA32_RESET, ioaddr);
- if (ei_debug > 1) printk("resetting Ultra32, t=%ld...", jiffies);
- ei_status.txing = 0;
-
- outb(ULTRA32_MEMENB, ioaddr); /* Enable Shared Memory. */
- outb(0x80, ioaddr + ULTRA32_CFG6); /* Enable Interrupts. */
- outb(0x84, ioaddr + 5); /* Enable MEM16 & Disable Bus Master. */
- outb(0x01, ioaddr + 6); /* Enable Interrupts. */
- if (ei_debug > 1) printk("reset done\n");
-}
-
-/* Grab the 8390 specific header. Similar to the block_input routine, but
- we don't need to be concerned with ring wrap as the header will be at
- the start of a page, so we optimize accordingly. */
-
-static void ultra32_get_8390_hdr(struct net_device *dev,
- struct e8390_pkt_hdr *hdr,
- int ring_page)
-{
- void __iomem *hdr_start = ei_status.mem + ((ring_page & 0x1f) << 8);
- unsigned int RamReg = dev->base_addr - ULTRA32_NIC_OFFSET + ULTRA32_CFG3;
-
- /* Select correct 8KB Window. */
- outb(ei_status.reg0 | ((ring_page & 0x60) >> 5), RamReg);
-
-#ifdef __BIG_ENDIAN
- /* Officially this is what we are doing, but the readl() is faster */
- /* unfortunately it isn't endian aware of the struct */
- memcpy_fromio(hdr, hdr_start, sizeof(struct e8390_pkt_hdr));
- hdr->count = le16_to_cpu(hdr->count);
-#else
- ((unsigned int*)hdr)[0] = readl(hdr_start);
-#endif
-}
-
-/* Block input and output are easy on shared memory ethercards, the only
- complication is when the ring buffer wraps, or in this case, when a
- packet spans an 8KB boundary. Note that the current 8KB segment is
- already set by the get_8390_hdr routine. */
-
-static void ultra32_block_input(struct net_device *dev,
- int count,
- struct sk_buff *skb,
- int ring_offset)
-{
- void __iomem *xfer_start = ei_status.mem + (ring_offset & 0x1fff);
- unsigned int RamReg = dev->base_addr - ULTRA32_NIC_OFFSET + ULTRA32_CFG3;
-
- if ((ring_offset & ~0x1fff) != ((ring_offset + count - 1) & ~0x1fff)) {
- int semi_count = 8192 - (ring_offset & 0x1FFF);
- memcpy_fromio(skb->data, xfer_start, semi_count);
- count -= semi_count;
- if (ring_offset < 96*256) {
- /* Select next 8KB Window. */
- ring_offset += semi_count;
- outb(ei_status.reg0 | ((ring_offset & 0x6000) >> 13), RamReg);
- memcpy_fromio(skb->data + semi_count, ei_status.mem, count);
- } else {
- /* Select first 8KB Window. */
- outb(ei_status.reg0, RamReg);
- memcpy_fromio(skb->data + semi_count, ei_status.mem + TX_PAGES * 256, count);
- }
- } else {
- memcpy_fromio(skb->data, xfer_start, count);
- }
-}
-
-static void ultra32_block_output(struct net_device *dev,
- int count,
- const unsigned char *buf,
- int start_page)
-{
- void __iomem *xfer_start = ei_status.mem + (start_page<<8);
- unsigned int RamReg = dev->base_addr - ULTRA32_NIC_OFFSET + ULTRA32_CFG3;
-
- /* Select first 8KB Window. */
- outb(ei_status.reg0, RamReg);
-
- memcpy_toio(xfer_start, buf, count);
-}
-
-#ifdef MODULE
-#define MAX_ULTRA32_CARDS 4 /* Max number of Ultra cards per module */
-static struct net_device *dev_ultra[MAX_ULTRA32_CARDS];
-
-MODULE_DESCRIPTION("SMC Ultra32 EISA ethernet driver");
-MODULE_LICENSE("GPL");
-
-int __init init_module(void)
-{
- int this_dev, found = 0;
-
- for (this_dev = 0; this_dev < MAX_ULTRA32_CARDS; this_dev++) {
- struct net_device *dev = ultra32_probe(-1);
- if (IS_ERR(dev))
- break;
- dev_ultra[found++] = dev;
- }
- if (found)
- return 0;
- printk(KERN_WARNING "smc-ultra32.c: No SMC Ultra32 found.\n");
- return -ENXIO;
-}
-
-void __exit cleanup_module(void)
-{
- int this_dev;
-
- for (this_dev = 0; this_dev < MAX_ULTRA32_CARDS; this_dev++) {
- struct net_device *dev = dev_ultra[this_dev];
- if (dev) {
- unregister_netdev(dev);
- cleanup_card(dev);
- free_netdev(dev);
- }
- }
-}
-#endif /* MODULE */
-
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-16 10:55:01 +0000