diff options
Diffstat (limited to 'drivers/serial/Kconfig')
| -rw-r--r-- | drivers/serial/Kconfig | 159 |
1 files changed, 97 insertions, 62 deletions
diff --git a/drivers/serial/Kconfig b/drivers/serial/Kconfig index 5b48ac22c9c5..0b36dd5cdac2 100644 --- a/drivers/serial/Kconfig +++ b/drivers/serial/Kconfig @@ -121,7 +121,7 @@ config SERIAL_8250_RUNTIME_UARTS default "4" help Set this to the maximum number of serial ports you want - the kernel to register at boot time. This can be overriden + the kernel to register at boot time. This can be overridden with the module parameter "nr_uarts", or boot-time parameter 8250.nr_uarts @@ -151,32 +151,6 @@ config SERIAL_8250_MANY_PORTS say N here to save some memory. You can also say Y if you have an "intelligent" multiport card such as Cyclades, Digiboards, etc. -config SERIAL_8250_SHARE_IRQ - bool "Support for sharing serial interrupts" - depends on SERIAL_8250_EXTENDED - help - Some serial boards have hardware support which allows multiple dumb - serial ports on the same board to share a single IRQ. To enable - support for this in the serial driver, say Y here. - -config SERIAL_8250_DETECT_IRQ - bool "Autodetect IRQ on standard ports (unsafe)" - depends on SERIAL_8250_EXTENDED - help - Say Y here if you want the kernel to try to guess which IRQ - to use for your serial port. - - This is considered unsafe; it is far better to configure the IRQ in - a boot script using the setserial command. - - If unsure, say N. - -config SERIAL_8250_RSA - bool "Support RSA serial ports" - depends on SERIAL_8250_EXTENDED - help - ::: To be written ::: - # # Multi-port serial cards # @@ -199,17 +173,27 @@ config SERIAL_8250_ACCENT To compile this driver as a module, choose M here: the module will be called 8250_accent. - config SERIAL_8250_BOCA tristate "Support Boca cards" depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS help Say Y here if you have a Boca serial board. Please read the Boca - mini-HOWTO, avaialble from <http://www.tldp.org/docs.html#howto> + mini-HOWTO, available from <http://www.tldp.org/docs.html#howto> To compile this driver as a module, choose M here: the module will be called 8250_boca. +config SERIAL_8250_EXAR_ST16C554 + tristate "Support Exar ST16C554/554D Quad UART" + depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS + help + The Uplogix Envoy TU301 uses this Exar Quad UART. If you are + tinkering with your Envoy TU301, or have a machine with this UART, + say Y here. + + To compile this driver as a module, choose M here: the module + will be called 8250_exar_st16c554. + config SERIAL_8250_HUB6 tristate "Support Hub6 cards" depends on SERIAL_8250 != n && ISA && SERIAL_8250_MANY_PORTS @@ -219,6 +203,32 @@ config SERIAL_8250_HUB6 To compile this driver as a module, choose M here: the module will be called 8250_hub6. +config SERIAL_8250_SHARE_IRQ + bool "Support for sharing serial interrupts" + depends on SERIAL_8250_EXTENDED + help + Some serial boards have hardware support which allows multiple dumb + serial ports on the same board to share a single IRQ. To enable + support for this in the serial driver, say Y here. + +config SERIAL_8250_DETECT_IRQ + bool "Autodetect IRQ on standard ports (unsafe)" + depends on SERIAL_8250_EXTENDED + help + Say Y here if you want the kernel to try to guess which IRQ + to use for your serial port. + + This is considered unsafe; it is far better to configure the IRQ in + a boot script using the setserial command. + + If unsure, say N. + +config SERIAL_8250_RSA + bool "Support RSA serial ports" + depends on SERIAL_8250_EXTENDED + help + ::: To be written ::: + config SERIAL_8250_MCA tristate "Support 8250-type ports on MCA buses" depends on SERIAL_8250 != n && MCA @@ -295,37 +305,37 @@ config SERIAL_AMBA_PL011_CONSOLE Even if you say Y here, the currently visible framebuffer console (/dev/tty0) will still be used as the system console by default, but you can alter that using a kernel command line option such as - "console=ttyAM0". (Try "man bootparam" or see the documentation of + "console=ttyAMA0". (Try "man bootparam" or see the documentation of your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) -config SERIAL_AT91 - bool "AT91RM9200 / AT91SAM9261 serial port support" - depends on ARM && (ARCH_AT91RM9200 || ARCH_AT91SAM9261) +config SERIAL_ATMEL + bool "AT91 / AT32 on-chip serial port support" + depends on (ARM && ARCH_AT91) || AVR32 select SERIAL_CORE help This enables the driver for the on-chip UARTs of the Atmel - AT91RM9200 and AT91SAM926 processor. + AT91 and AT32 processors. -config SERIAL_AT91_CONSOLE - bool "Support for console on AT91RM9200 / AT91SAM9261 serial port" - depends on SERIAL_AT91=y +config SERIAL_ATMEL_CONSOLE + bool "Support for console on AT91 / AT32 serial port" + depends on SERIAL_ATMEL=y select SERIAL_CORE_CONSOLE help - Say Y here if you wish to use a UART on the Atmel AT91RM9200 or - AT91SAM9261 as the system console (the system console is the device - which receives all kernel messages and warnings and which allows - logins in single user mode). + Say Y here if you wish to use an on-chip UART on a Atmel + AT91 or AT32 processor as the system console (the system + console is the device which receives all kernel messages and + warnings and which allows logins in single user mode). -config SERIAL_AT91_TTYAT - bool "Install as device ttyAT0-4 instead of ttyS0-4" - depends on SERIAL_AT91=y +config SERIAL_ATMEL_TTYAT + bool "Install as device ttyATn instead of ttySn" + depends on SERIAL_ATMEL=y help - Say Y here if you wish to have the five internal AT91RM9200 UARTs - appear as /dev/ttyAT0-4 (major 204, minor 154-158) instead of the - normal /dev/ttyS0-4 (major 4, minor 64-68). This is necessary if - you also want other UARTs, such as external 8250/16C550 compatible - UARTs. + Say Y here if you wish to have the internal AT91 / AT32 UARTs + appear as /dev/ttyATn (major 204, minor starting at 154) + instead of the normal /dev/ttySn (major 4, minor starting at + 64). This is necessary if you also want other UARTs, such as + external 8250/16C550 compatible UARTs. The ttySn nodes are legally reserved for the 8250 serial driver but are often misused by other serial drivers. @@ -511,6 +521,25 @@ config SERIAL_IMX_CONSOLE your boot loader (lilo or loadlin) about how to pass options to the kernel at boot time.) +config SERIAL_UARTLITE + tristate "Xilinx uartlite serial port support" + depends on PPC32 + select SERIAL_CORE + help + Say Y here if you want to use the Xilinx uartlite serial controller. + + To compile this driver as a module, choose M here: the + module will be called uartlite.ko. + +config SERIAL_UARTLITE_CONSOLE + bool "Support for console on Xilinx uartlite serial port" + depends on SERIAL_UARTLITE=y + select SERIAL_CORE_CONSOLE + help + Say Y here if you wish to use a Xilinx uartlite as the system + console (the system console is the device which receives all kernel + messages and warnings and which allows logins in single user mode). + config SERIAL_SUNCORE bool depends on SPARC @@ -556,10 +585,11 @@ config SERIAL_MUX default y ---help--- Saying Y here will enable the hardware MUX serial driver for - the Nova and K class systems. The hardware MUX is not 8250/16550 - compatible therefore the /dev/ttyB0 device is shared between the - Serial MUX and the PDC software console. The following steps - need to be completed to use the Serial MUX: + the Nova, K class systems and D class with a 'remote control card'. + The hardware MUX is not 8250/16550 compatible therefore the + /dev/ttyB0 device is shared between the Serial MUX and the PDC + software console. The following steps need to be completed to use + the Serial MUX: 1. create the device entry (mknod /dev/ttyB0 c 11 0) 2. Edit the /etc/inittab to start a getty listening on /dev/ttyB0 @@ -642,12 +672,17 @@ config V850E_UART_CONSOLE select SERIAL_CORE_CONSOLE config SERIAL_SH_SCI - tristate "SH SCI(F) serial port support" + tristate "SuperH SCI(F) serial port support" depends on SUPERH || H8300 select SERIAL_CORE +config SERIAL_SH_SCI_NR_UARTS + int "Maximum number of SCI(F) serial ports" + depends on SERIAL_SH_SCI + default "2" + config SERIAL_SH_SCI_CONSOLE - bool "Support for console on SH SCI(F)" + bool "Support for console on SuperH SCI(F)" depends on SERIAL_SH_SCI=y select SERIAL_CORE_CONSOLE @@ -662,7 +697,7 @@ config SERIAL_68328 depends on M68328 || M68EZ328 || M68VZ328 help This driver supports the built-in serial port of the Motorola 68328 - (standard, EZ and VZ varities). + (standard, EZ and VZ varieties). config SERIAL_68328_RTS_CTS bool "Support RTS/CTS on 68328 serial port" @@ -761,37 +796,37 @@ config SERIAL_CPM_SCC1 bool "Support for SCC1 serial port" depends on SERIAL_CPM=y help - Select the is option to use SCC1 as a serial port + Select this option to use SCC1 as a serial port config SERIAL_CPM_SCC2 bool "Support for SCC2 serial port" depends on SERIAL_CPM=y help - Select the is option to use SCC2 as a serial port + Select this option to use SCC2 as a serial port config SERIAL_CPM_SCC3 bool "Support for SCC3 serial port" depends on SERIAL_CPM=y help - Select the is option to use SCC3 as a serial port + Select this option to use SCC3 as a serial port config SERIAL_CPM_SCC4 bool "Support for SCC4 serial port" depends on SERIAL_CPM=y help - Select the is option to use SCC4 as a serial port + Select this option to use SCC4 as a serial port config SERIAL_CPM_SMC1 bool "Support for SMC1 serial port" depends on SERIAL_CPM=y help - Select the is option to use SMC1 as a serial port + Select this option to use SMC1 as a serial port config SERIAL_CPM_SMC2 bool "Support for SMC2 serial port" depends on SERIAL_CPM=y help - Select the is option to use SMC2 as a serial port + Select this option to use SMC2 as a serial port config SERIAL_SGI_L1_CONSOLE bool "SGI Altix L1 serial console support" |