summaryrefslogtreecommitdiff
path: root/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c
diff options
context:
space:
mode:
Diffstat (limited to 'drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c')
-rw-r--r--drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c123
1 files changed, 117 insertions, 6 deletions
diff --git a/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c b/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c
index 0c89647f166f..ec48c59e84ae 100644
--- a/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c
+++ b/drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c
@@ -25,6 +25,32 @@
#include "../pinctrl-utils.h"
#include "pinctrl-aspeed.h"
+/*
+ * The "Multi-function Pins Mapping and Control" table in the SoC datasheet
+ * references registers by the device/offset mnemonic. The register macros
+ * below are named the same way to ease transcription and verification (as
+ * opposed to naming them e.g. PINMUX_CTRL_[0-9]). Further, signal expressions
+ * reference registers beyond those dedicated to pinmux, such as the system
+ * reset control and MAC clock configuration registers. The AST2500 goes a step
+ * further and references registers in the graphics IP block.
+ */
+#define SCU2C 0x2C /* Misc. Control Register */
+#define SCU3C 0x3C /* System Reset Control/Status Register */
+#define SCU48 0x48 /* MAC Interface Clock Delay Setting */
+#define HW_STRAP1 0x70 /* AST2400 strapping is 33 bits, is split */
+#define HW_REVISION_ID 0x7C /* Silicon revision ID register */
+#define SCU80 0x80 /* Multi-function Pin Control #1 */
+#define SCU84 0x84 /* Multi-function Pin Control #2 */
+#define SCU88 0x88 /* Multi-function Pin Control #3 */
+#define SCU8C 0x8C /* Multi-function Pin Control #4 */
+#define SCU90 0x90 /* Multi-function Pin Control #5 */
+#define SCU94 0x94 /* Multi-function Pin Control #6 */
+#define SCUA0 0xA0 /* Multi-function Pin Control #7 */
+#define SCUA4 0xA4 /* Multi-function Pin Control #8 */
+#define SCUA8 0xA8 /* Multi-function Pin Control #9 */
+#define SCUAC 0xAC /* Multi-function Pin Control #10 */
+#define HW_STRAP2 0xD0 /* Strapping */
+
#define ASPEED_G5_NR_PINS 236
#define COND1 { ASPEED_IP_SCU, SCU90, BIT(6), 0, 0 }
@@ -2485,13 +2511,98 @@ static struct aspeed_pin_config aspeed_g5_configs[] = {
{ PIN_CONFIG_INPUT_DEBOUNCE, { A20, B19 }, SCUA8, 27 },
};
+/**
+ * Configure a pin's signal by applying an expression's descriptor state for
+ * all descriptors in the expression.
+ *
+ * @ctx: The pinmux context
+ * @expr: The expression associated with the function whose signal is to be
+ * configured
+ * @enable: true to enable an function's signal through a pin's signal
+ * expression, false to disable the function's signal
+ *
+ * Return: 0 if the expression is configured as requested and a negative error
+ * code otherwise
+ */
+static int aspeed_g5_sig_expr_set(const struct aspeed_pinmux_data *ctx,
+ const struct aspeed_sig_expr *expr,
+ bool enable)
+{
+ int ret;
+ int i;
+
+ for (i = 0; i < expr->ndescs; i++) {
+ const struct aspeed_sig_desc *desc = &expr->descs[i];
+ u32 pattern = enable ? desc->enable : desc->disable;
+ u32 val = (pattern << __ffs(desc->mask));
+
+ if (!ctx->maps[desc->ip])
+ return -ENODEV;
+
+ /*
+ * Strap registers are configured in hardware or by early-boot
+ * firmware. Treat them as read-only despite that we can write
+ * them. This may mean that certain functions cannot be
+ * deconfigured and is the reason we re-evaluate after writing
+ * all descriptor bits.
+ *
+ * Port D and port E GPIO loopback modes are the only exception
+ * as those are commonly used with front-panel buttons to allow
+ * normal operation of the host when the BMC is powered off or
+ * fails to boot. Once the BMC has booted, the loopback mode
+ * must be disabled for the BMC to control host power-on and
+ * reset.
+ */
+ if (desc->ip == ASPEED_IP_SCU && desc->reg == HW_STRAP1 &&
+ !(desc->mask & (BIT(21) | BIT(22))))
+ continue;
+
+ if (desc->ip == ASPEED_IP_SCU && desc->reg == HW_STRAP2)
+ continue;
+
+ /* On AST2500, Set bits in SCU70 are cleared from SCU7C */
+ if (desc->ip == ASPEED_IP_SCU && desc->reg == HW_STRAP1) {
+ u32 value = ~val & desc->mask;
+
+ if (value) {
+ ret = regmap_write(ctx->maps[desc->ip],
+ HW_REVISION_ID, value);
+ if (ret < 0)
+ return ret;
+ }
+ }
+
+ ret = regmap_update_bits(ctx->maps[desc->ip], desc->reg,
+ desc->mask, val);
+
+ if (ret)
+ return ret;
+ }
+
+ ret = aspeed_sig_expr_eval(ctx, expr, enable);
+ if (ret < 0)
+ return ret;
+
+ if (!ret)
+ return -EPERM;
+
+ return 0;
+}
+
+static const struct aspeed_pinmux_ops aspeed_g5_ops = {
+ .set = aspeed_g5_sig_expr_set,
+};
+
static struct aspeed_pinctrl_data aspeed_g5_pinctrl_data = {
.pins = aspeed_g5_pins,
.npins = ARRAY_SIZE(aspeed_g5_pins),
- .groups = aspeed_g5_groups,
- .ngroups = ARRAY_SIZE(aspeed_g5_groups),
- .functions = aspeed_g5_functions,
- .nfunctions = ARRAY_SIZE(aspeed_g5_functions),
+ .pinmux = {
+ .ops = &aspeed_g5_ops,
+ .groups = aspeed_g5_groups,
+ .ngroups = ARRAY_SIZE(aspeed_g5_groups),
+ .functions = aspeed_g5_functions,
+ .nfunctions = ARRAY_SIZE(aspeed_g5_functions),
+ },
.configs = aspeed_g5_configs,
.nconfigs = ARRAY_SIZE(aspeed_g5_configs),
};
@@ -2547,7 +2658,7 @@ static int aspeed_g5_pinctrl_probe(struct platform_device *pdev)
dev_warn(&pdev->dev, "No GFX phandle found, some mux configurations may fail\n");
map = NULL;
}
- aspeed_g5_pinctrl_data.maps[ASPEED_IP_GFX] = map;
+ aspeed_g5_pinctrl_data.pinmux.maps[ASPEED_IP_GFX] = map;
node = of_parse_phandle(pdev->dev.of_node, "aspeed,external-nodes", 1);
if (node) {
@@ -2561,7 +2672,7 @@ static int aspeed_g5_pinctrl_probe(struct platform_device *pdev)
map = NULL;
}
of_node_put(node);
- aspeed_g5_pinctrl_data.maps[ASPEED_IP_LPC] = map;
+ aspeed_g5_pinctrl_data.pinmux.maps[ASPEED_IP_LPC] = map;
return aspeed_pinctrl_probe(pdev, &aspeed_g5_pinctrl_desc,
&aspeed_g5_pinctrl_data);