diff options
Diffstat (limited to 'drivers/net/wireless')
22 files changed, 89 insertions, 440 deletions
diff --git a/drivers/net/wireless/ath/ath5k/base.c b/drivers/net/wireless/ath/ath5k/base.c index 20c7e5b450aa..fdfaf0f618f1 100644 --- a/drivers/net/wireless/ath/ath5k/base.c +++ b/drivers/net/wireless/ath/ath5k/base.c @@ -1903,17 +1903,6 @@ accept: rxs->noise = sc->ah->ah_noise_floor; rxs->signal = rxs->noise + rs.rs_rssi; - /* An rssi of 35 indicates you should be able use - * 54 Mbps reliably. A more elaborate scheme can be used - * here but it requires a map of SNR/throughput for each - * possible mode used */ - rxs->qual = rs.rs_rssi * 100 / 35; - - /* rssi can be more than 35 though, anything above that - * should be considered at 100% */ - if (rxs->qual > 100) - rxs->qual = 100; - rxs->antenna = rs.rs_antenna; rxs->rate_idx = ath5k_hw_to_driver_rix(sc, rs.rs_rate); rxs->flag |= ath5k_rx_decrypted(sc, ds, skb, &rs); @@ -2381,6 +2370,9 @@ ath5k_init(struct ath5k_softc *sc) */ ath5k_stop_locked(sc); + /* Set PHY calibration interval */ + ah->ah_cal_intval = ath5k_calinterval; + /* * The basic interface to setting the hardware in a good * state is ``reset''. On return the hardware is known to @@ -2408,10 +2400,6 @@ ath5k_init(struct ath5k_softc *sc) /* Set ack to be sent at low bit-rates */ ath5k_hw_set_ack_bitrate_high(ah, false); - - /* Set PHY calibration inteval */ - ah->ah_cal_intval = ath5k_calinterval; - ret = 0; done: mmiowb(); diff --git a/drivers/net/wireless/ath/ath9k/mac.h b/drivers/net/wireless/ath/ath9k/mac.h index 0c87771383f0..e185479e295e 100644 --- a/drivers/net/wireless/ath/ath9k/mac.h +++ b/drivers/net/wireless/ath/ath9k/mac.h @@ -77,6 +77,9 @@ #define ATH9K_TXERR_XTXOP 0x08 #define ATH9K_TXERR_TIMER_EXPIRED 0x10 #define ATH9K_TX_ACKED 0x20 +#define ATH9K_TXERR_MASK \ + (ATH9K_TXERR_XRETRY | ATH9K_TXERR_FILT | ATH9K_TXERR_FIFO | \ + ATH9K_TXERR_XTXOP | ATH9K_TXERR_TIMER_EXPIRED) #define ATH9K_TX_BA 0x01 #define ATH9K_TX_PWRMGMT 0x02 diff --git a/drivers/net/wireless/ath/ath9k/main.c b/drivers/net/wireless/ath/ath9k/main.c index 446bd23756e5..79fbbda15493 100644 --- a/drivers/net/wireless/ath/ath9k/main.c +++ b/drivers/net/wireless/ath/ath9k/main.c @@ -2504,6 +2504,9 @@ static void ath9k_stop(struct ieee80211_hw *hw) return; /* another wiphy still in use */ } + /* Ensure HW is awake when we try to shut it down. */ + ath9k_ps_wakeup(sc); + if (ah->btcoex_hw.enabled) { ath9k_hw_btcoex_disable(ah); if (ah->btcoex_hw.scheme == ATH_BTCOEX_CFG_3WIRE) @@ -2524,6 +2527,9 @@ static void ath9k_stop(struct ieee80211_hw *hw) /* disable HAL and put h/w to sleep */ ath9k_hw_disable(ah); ath9k_hw_configpcipowersave(ah, 1, 1); + ath9k_ps_restore(sc); + + /* Finally, put the chip in FULL SLEEP mode */ ath9k_setpower(sc, ATH9K_PM_FULL_SLEEP); sc->sc_flags |= SC_OP_INVALID; @@ -2637,8 +2643,10 @@ static void ath9k_remove_interface(struct ieee80211_hw *hw, if ((sc->sc_ah->opmode == NL80211_IFTYPE_AP) || (sc->sc_ah->opmode == NL80211_IFTYPE_ADHOC) || (sc->sc_ah->opmode == NL80211_IFTYPE_MESH_POINT)) { + ath9k_ps_wakeup(sc); ath9k_hw_stoptxdma(sc->sc_ah, sc->beacon.beaconq); ath_beacon_return(sc, avp); + ath9k_ps_restore(sc); } sc->sc_flags &= ~SC_OP_BEACONS; @@ -3087,15 +3095,21 @@ static int ath9k_ampdu_action(struct ieee80211_hw *hw, case IEEE80211_AMPDU_RX_STOP: break; case IEEE80211_AMPDU_TX_START: + ath9k_ps_wakeup(sc); ath_tx_aggr_start(sc, sta, tid, ssn); ieee80211_start_tx_ba_cb_irqsafe(vif, sta->addr, tid); + ath9k_ps_restore(sc); break; case IEEE80211_AMPDU_TX_STOP: + ath9k_ps_wakeup(sc); ath_tx_aggr_stop(sc, sta, tid); ieee80211_stop_tx_ba_cb_irqsafe(vif, sta->addr, tid); + ath9k_ps_restore(sc); break; case IEEE80211_AMPDU_TX_OPERATIONAL: + ath9k_ps_wakeup(sc); ath_tx_aggr_resume(sc, sta, tid); + ath9k_ps_restore(sc); break; default: ath_print(ath9k_hw_common(sc->sc_ah), ATH_DBG_FATAL, diff --git a/drivers/net/wireless/ath/ath9k/pci.c b/drivers/net/wireless/ath/ath9k/pci.c index 5321f735e5a0..f7af5ea54753 100644 --- a/drivers/net/wireless/ath/ath9k/pci.c +++ b/drivers/net/wireless/ath/ath9k/pci.c @@ -96,7 +96,7 @@ static void ath_pci_bt_coex_prep(struct ath_common *common) pci_write_config_byte(pdev, ATH_PCIE_CAP_LINK_CTRL, aspm); } -const static struct ath_bus_ops ath_pci_bus_ops = { +static const struct ath_bus_ops ath_pci_bus_ops = { .read_cachesize = ath_pci_read_cachesize, .cleanup = ath_pci_cleanup, .eeprom_read = ath_pci_eeprom_read, diff --git a/drivers/net/wireless/ath/ath9k/xmit.c b/drivers/net/wireless/ath/ath9k/xmit.c index 1e813bbf474a..fa12b9060b0b 100644 --- a/drivers/net/wireless/ath/ath9k/xmit.c +++ b/drivers/net/wireless/ath/ath9k/xmit.c @@ -2072,7 +2072,7 @@ static void ath_tx_processq(struct ath_softc *sc, struct ath_txq *txq) &txq->axq_q, lastbf->list.prev); txq->axq_depth--; - txok = !(ds->ds_txstat.ts_status & ATH9K_TXERR_FILT); + txok = !(ds->ds_txstat.ts_status & ATH9K_TXERR_MASK); txq->axq_tx_inprogress = false; spin_unlock_bh(&txq->axq_lock); diff --git a/drivers/net/wireless/b43/dma.c b/drivers/net/wireless/b43/dma.c index 5dd8a210ac21..615af22c49fd 100644 --- a/drivers/net/wireless/b43/dma.c +++ b/drivers/net/wireless/b43/dma.c @@ -383,160 +383,44 @@ static inline } } -/* Check if a DMA region fits the device constraints. - * Returns true, if the region is OK for usage with this device. */ -static inline bool b43_dma_address_ok(struct b43_dmaring *ring, - dma_addr_t addr, size_t size) -{ - switch (ring->type) { - case B43_DMA_30BIT: - if ((u64)addr + size > (1ULL << 30)) - return 0; - break; - case B43_DMA_32BIT: - if ((u64)addr + size > (1ULL << 32)) - return 0; - break; - case B43_DMA_64BIT: - /* Currently we can't have addresses beyond - * 64bit in the kernel. */ - break; - } - return 1; -} - -#define is_4k_aligned(addr) (((u64)(addr) & 0x0FFFull) == 0) -#define is_8k_aligned(addr) (((u64)(addr) & 0x1FFFull) == 0) - -static void b43_unmap_and_free_ringmem(struct b43_dmaring *ring, void *base, - dma_addr_t dmaaddr, size_t size) -{ - ssb_dma_unmap_single(ring->dev->dev, dmaaddr, size, DMA_TO_DEVICE); - free_pages((unsigned long)base, get_order(size)); -} - -static void * __b43_get_and_map_ringmem(struct b43_dmaring *ring, - dma_addr_t *dmaaddr, size_t size, - gfp_t gfp_flags) -{ - void *base; - - base = (void *)__get_free_pages(gfp_flags, get_order(size)); - if (!base) - return NULL; - memset(base, 0, size); - *dmaaddr = ssb_dma_map_single(ring->dev->dev, base, size, - DMA_TO_DEVICE); - if (ssb_dma_mapping_error(ring->dev->dev, *dmaaddr)) { - free_pages((unsigned long)base, get_order(size)); - return NULL; - } - - return base; -} - -static void * b43_get_and_map_ringmem(struct b43_dmaring *ring, - dma_addr_t *dmaaddr, size_t size) -{ - void *base; - - base = __b43_get_and_map_ringmem(ring, dmaaddr, size, - GFP_KERNEL); - if (!base) { - b43err(ring->dev->wl, "Failed to allocate or map pages " - "for DMA ringmemory\n"); - return NULL; - } - if (!b43_dma_address_ok(ring, *dmaaddr, size)) { - /* The memory does not fit our device constraints. - * Retry with GFP_DMA set to get lower memory. */ - b43_unmap_and_free_ringmem(ring, base, *dmaaddr, size); - base = __b43_get_and_map_ringmem(ring, dmaaddr, size, - GFP_KERNEL | GFP_DMA); - if (!base) { - b43err(ring->dev->wl, "Failed to allocate or map pages " - "in the GFP_DMA region for DMA ringmemory\n"); - return NULL; - } - if (!b43_dma_address_ok(ring, *dmaaddr, size)) { - b43_unmap_and_free_ringmem(ring, base, *dmaaddr, size); - b43err(ring->dev->wl, "Failed to allocate DMA " - "ringmemory that fits device constraints\n"); - return NULL; - } - } - /* We expect the memory to be 4k aligned, at least. */ - if (B43_WARN_ON(!is_4k_aligned(*dmaaddr))) { - b43_unmap_and_free_ringmem(ring, base, *dmaaddr, size); - return NULL; - } - - return base; -} - static int alloc_ringmemory(struct b43_dmaring *ring) { - unsigned int required; - void *base; - dma_addr_t dmaaddr; - - /* There are several requirements to the descriptor ring memory: - * - The memory region needs to fit the address constraints for the - * device (same as for frame buffers). - * - For 30/32bit DMA devices, the descriptor ring must be 4k aligned. - * - For 64bit DMA devices, the descriptor ring must be 8k aligned. + gfp_t flags = GFP_KERNEL; + + /* The specs call for 4K buffers for 30- and 32-bit DMA with 4K + * alignment and 8K buffers for 64-bit DMA with 8K alignment. Testing + * has shown that 4K is sufficient for the latter as long as the buffer + * does not cross an 8K boundary. + * + * For unknown reasons - possibly a hardware error - the BCM4311 rev + * 02, which uses 64-bit DMA, needs the ring buffer in very low memory, + * which accounts for the GFP_DMA flag below. + * + * The flags here must match the flags in free_ringmemory below! */ - if (ring->type == B43_DMA_64BIT) - required = ring->nr_slots * sizeof(struct b43_dmadesc64); - else - required = ring->nr_slots * sizeof(struct b43_dmadesc32); - if (B43_WARN_ON(required > 0x1000)) + flags |= GFP_DMA; + ring->descbase = ssb_dma_alloc_consistent(ring->dev->dev, + B43_DMA_RINGMEMSIZE, + &(ring->dmabase), flags); + if (!ring->descbase) { + b43err(ring->dev->wl, "DMA ringmemory allocation failed\n"); return -ENOMEM; - - ring->alloc_descsize = 0x1000; - base = b43_get_and_map_ringmem(ring, &dmaaddr, ring->alloc_descsize); - if (!base) - return -ENOMEM; - ring->alloc_descbase = base; - ring->alloc_dmabase = dmaaddr; - - if ((ring->type != B43_DMA_64BIT) || is_8k_aligned(dmaaddr)) { - /* We're on <=32bit DMA, or we already got 8k aligned memory. - * That's all we need, so we're fine. */ - ring->descbase = base; - ring->dmabase = dmaaddr; - return 0; - } - b43_unmap_and_free_ringmem(ring, base, dmaaddr, ring->alloc_descsize); - - /* Ok, we failed at the 8k alignment requirement. - * Try to force-align the memory region now. */ - ring->alloc_descsize = 0x2000; - base = b43_get_and_map_ringmem(ring, &dmaaddr, ring->alloc_descsize); - if (!base) - return -ENOMEM; - ring->alloc_descbase = base; - ring->alloc_dmabase = dmaaddr; - - if (is_8k_aligned(dmaaddr)) { - /* We're already 8k aligned. That Ok, too. */ - ring->descbase = base; - ring->dmabase = dmaaddr; - return 0; } - /* Force-align it to 8k */ - ring->descbase = (void *)((u8 *)base + 0x1000); - ring->dmabase = dmaaddr + 0x1000; - B43_WARN_ON(!is_8k_aligned(ring->dmabase)); + memset(ring->descbase, 0, B43_DMA_RINGMEMSIZE); return 0; } static void free_ringmemory(struct b43_dmaring *ring) { - b43_unmap_and_free_ringmem(ring, ring->alloc_descbase, - ring->alloc_dmabase, ring->alloc_descsize); + gfp_t flags = GFP_KERNEL; + + if (ring->type == B43_DMA_64BIT) + flags |= GFP_DMA; + + ssb_dma_free_consistent(ring->dev->dev, B43_DMA_RINGMEMSIZE, + ring->descbase, ring->dmabase, flags); } /* Reset the RX DMA channel */ @@ -646,14 +530,29 @@ static bool b43_dma_mapping_error(struct b43_dmaring *ring, if (unlikely(ssb_dma_mapping_error(ring->dev->dev, addr))) return 1; - if (!b43_dma_address_ok(ring, addr, buffersize)) { - /* We can't support this address. Unmap it again. */ - unmap_descbuffer(ring, addr, buffersize, dma_to_device); - return 1; + switch (ring->type) { + case B43_DMA_30BIT: + if ((u64)addr + buffersize > (1ULL << 30)) + goto address_error; + break; + case B43_DMA_32BIT: + if ((u64)addr + buffersize > (1ULL << 32)) + goto address_error; + break; + case B43_DMA_64BIT: + /* Currently we can't have addresses beyond + * 64bit in the kernel. */ + break; } /* The address is OK. */ return 0; + +address_error: + /* We can't support this address. Unmap it again. */ + unmap_descbuffer(ring, addr, buffersize, dma_to_device); + + return 1; } static bool b43_rx_buffer_is_poisoned(struct b43_dmaring *ring, struct sk_buff *skb) @@ -715,9 +614,6 @@ static int setup_rx_descbuffer(struct b43_dmaring *ring, meta->dmaaddr = dmaaddr; ring->ops->fill_descriptor(ring, desc, dmaaddr, ring->rx_buffersize, 0, 0, 0); - ssb_dma_sync_single_for_device(ring->dev->dev, - ring->alloc_dmabase, - ring->alloc_descsize, DMA_TO_DEVICE); return 0; } @@ -1354,9 +1250,6 @@ static int dma_tx_fragment(struct b43_dmaring *ring, } /* Now transfer the whole frame. */ wmb(); - ssb_dma_sync_single_for_device(ring->dev->dev, - ring->alloc_dmabase, - ring->alloc_descsize, DMA_TO_DEVICE); ops->poke_tx(ring, next_slot(ring, slot)); return 0; diff --git a/drivers/net/wireless/b43/dma.h b/drivers/net/wireless/b43/dma.h index e607b392314c..f7ab37c4cdbc 100644 --- a/drivers/net/wireless/b43/dma.h +++ b/drivers/net/wireless/b43/dma.h @@ -157,6 +157,7 @@ struct b43_dmadesc_generic { } __attribute__ ((__packed__)); /* Misc DMA constants */ +#define B43_DMA_RINGMEMSIZE PAGE_SIZE #define B43_DMA0_RX_FRAMEOFFSET 30 /* DMA engine tuning knobs */ @@ -246,12 +247,6 @@ struct b43_dmaring { /* The QOS priority assigned to this ring. Only used for TX rings. * This is the mac80211 "queue" value. */ u8 queue_prio; - /* Pointers and size of the originally allocated and mapped memory - * region for the descriptor ring. */ - void *alloc_descbase; - dma_addr_t alloc_dmabase; - unsigned int alloc_descsize; - /* Pointer to our wireless device. */ struct b43_wldev *dev; #ifdef CONFIG_B43_DEBUG /* Maximum number of used slots. */ diff --git a/drivers/net/wireless/iwlwifi/iwl-3945.c b/drivers/net/wireless/iwlwifi/iwl-3945.c index d1bab141508a..28ffe4c826d8 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945.c +++ b/drivers/net/wireless/iwlwifi/iwl-3945.c @@ -681,19 +681,13 @@ static void iwl3945_rx_reply_rx(struct iwl_priv *priv, snr = rx_stats_sig_avg / rx_stats_noise_diff; rx_status.noise = rx_status.signal - iwl3945_calc_db_from_ratio(snr); - rx_status.qual = iwl3945_calc_sig_qual(rx_status.signal, - rx_status.noise); - - /* If noise info not available, calculate signal quality indicator (%) - * using just the dBm signal level. */ } else { rx_status.noise = priv->last_rx_noise; - rx_status.qual = iwl3945_calc_sig_qual(rx_status.signal, 0); } - IWL_DEBUG_STATS(priv, "Rssi %d noise %d qual %d sig_avg %d noise_diff %d\n", - rx_status.signal, rx_status.noise, rx_status.qual, + IWL_DEBUG_STATS(priv, "Rssi %d noise %d sig_avg %d noise_diff %d\n", + rx_status.signal, rx_status.noise, rx_stats_sig_avg, rx_stats_noise_diff); header = (struct ieee80211_hdr *)IWL_RX_DATA(pkt); diff --git a/drivers/net/wireless/iwlwifi/iwl-3945.h b/drivers/net/wireless/iwlwifi/iwl-3945.h index 28f6eb5f2cba..3ec2fe370b58 100644 --- a/drivers/net/wireless/iwlwifi/iwl-3945.h +++ b/drivers/net/wireless/iwlwifi/iwl-3945.h @@ -222,7 +222,6 @@ struct iwl3945_ibss_seq { * *****************************************************************************/ extern int iwl3945_calc_db_from_ratio(int sig_ratio); -extern int iwl3945_calc_sig_qual(int rssi_dbm, int noise_dbm); extern void iwl3945_rx_replenish(void *data); extern void iwl3945_rx_queue_reset(struct iwl_priv *priv, struct iwl_rx_queue *rxq); extern unsigned int iwl3945_fill_beacon_frame(struct iwl_priv *priv, diff --git a/drivers/net/wireless/iwlwifi/iwl-agn-rs.c b/drivers/net/wireless/iwlwifi/iwl-agn-rs.c index fe511cbf012e..b93e49158196 100644 --- a/drivers/net/wireless/iwlwifi/iwl-agn-rs.c +++ b/drivers/net/wireless/iwlwifi/iwl-agn-rs.c @@ -150,7 +150,7 @@ static s32 expected_tpt_mimo3_40MHz[4][IWL_RATE_COUNT] = { }; /* mbps, mcs */ -const static struct iwl_rate_mcs_info iwl_rate_mcs[IWL_RATE_COUNT] = { +static const struct iwl_rate_mcs_info iwl_rate_mcs[IWL_RATE_COUNT] = { { "1", "BPSK DSSS"}, { "2", "QPSK DSSS"}, {"5.5", "BPSK CCK"}, diff --git a/drivers/net/wireless/iwlwifi/iwl-rx.c b/drivers/net/wireless/iwlwifi/iwl-rx.c index f5c87e72660a..6f36b6e79f5e 100644 --- a/drivers/net/wireless/iwlwifi/iwl-rx.c +++ b/drivers/net/wireless/iwlwifi/iwl-rx.c @@ -650,47 +650,6 @@ void iwl_reply_statistics(struct iwl_priv *priv, } EXPORT_SYMBOL(iwl_reply_statistics); -#define PERFECT_RSSI (-20) /* dBm */ -#define WORST_RSSI (-95) /* dBm */ -#define RSSI_RANGE (PERFECT_RSSI - WORST_RSSI) - -/* Calculate an indication of rx signal quality (a percentage, not dBm!). - * See http://www.ces.clemson.edu/linux/signal_quality.shtml for info - * about formulas used below. */ -static int iwl_calc_sig_qual(int rssi_dbm, int noise_dbm) -{ - int sig_qual; - int degradation = PERFECT_RSSI - rssi_dbm; - - /* If we get a noise measurement, use signal-to-noise ratio (SNR) - * as indicator; formula is (signal dbm - noise dbm). - * SNR at or above 40 is a great signal (100%). - * Below that, scale to fit SNR of 0 - 40 dB within 0 - 100% indicator. - * Weakest usable signal is usually 10 - 15 dB SNR. */ - if (noise_dbm) { - if (rssi_dbm - noise_dbm >= 40) - return 100; - else if (rssi_dbm < noise_dbm) - return 0; - sig_qual = ((rssi_dbm - noise_dbm) * 5) / 2; - - /* Else use just the signal level. - * This formula is a least squares fit of data points collected and - * compared with a reference system that had a percentage (%) display - * for signal quality. */ - } else - sig_qual = (100 * (RSSI_RANGE * RSSI_RANGE) - degradation * - (15 * RSSI_RANGE + 62 * degradation)) / - (RSSI_RANGE * RSSI_RANGE); - - if (sig_qual > 100) - sig_qual = 100; - else if (sig_qual < 1) - sig_qual = 0; - - return sig_qual; -} - /* Calc max signal level (dBm) among 3 possible receivers */ static inline int iwl_calc_rssi(struct iwl_priv *priv, struct iwl_rx_phy_res *rx_resp) @@ -1101,11 +1060,8 @@ void iwl_rx_reply_rx(struct iwl_priv *priv, if (iwl_is_associated(priv) && !test_bit(STATUS_SCANNING, &priv->status)) { rx_status.noise = priv->last_rx_noise; - rx_status.qual = iwl_calc_sig_qual(rx_status.signal, - rx_status.noise); } else { rx_status.noise = IWL_NOISE_MEAS_NOT_AVAILABLE; - rx_status.qual = iwl_calc_sig_qual(rx_status.signal, 0); } /* Reset beacon noise level if not associated. */ @@ -1118,8 +1074,8 @@ void iwl_rx_reply_rx(struct iwl_priv *priv, iwl_dbg_report_frame(priv, phy_res, len, header, 1); #endif iwl_dbg_log_rx_data_frame(priv, len, header); - IWL_DEBUG_STATS_LIMIT(priv, "Rssi %d, noise %d, qual %d, TSF %llu\n", - rx_status.signal, rx_status.noise, rx_status.qual, + IWL_DEBUG_STATS_LIMIT(priv, "Rssi %d, noise %d, TSF %llu\n", + rx_status.signal, rx_status.noise, (unsigned long long)rx_status.mactime); /* diff --git a/drivers/net/wireless/iwlwifi/iwl3945-base.c b/drivers/net/wireless/iwlwifi/iwl3945-base.c index 6533122ed87a..10b0aa8024c4 100644 --- a/drivers/net/wireless/iwlwifi/iwl3945-base.c +++ b/drivers/net/wireless/iwlwifi/iwl3945-base.c @@ -1299,47 +1299,6 @@ int iwl3945_calc_db_from_ratio(int sig_ratio) return (int)ratio2dB[sig_ratio]; } -#define PERFECT_RSSI (-20) /* dBm */ -#define WORST_RSSI (-95) /* dBm */ -#define RSSI_RANGE (PERFECT_RSSI - WORST_RSSI) - -/* Calculate an indication of rx signal quality (a percentage, not dBm!). - * See http://www.ces.clemson.edu/linux/signal_quality.shtml for info - * about formulas used below. */ -int iwl3945_calc_sig_qual(int rssi_dbm, int noise_dbm) -{ - int sig_qual; - int degradation = PERFECT_RSSI - rssi_dbm; - - /* If we get a noise measurement, use signal-to-noise ratio (SNR) - * as indicator; formula is (signal dbm - noise dbm). - * SNR at or above 40 is a great signal (100%). - * Below that, scale to fit SNR of 0 - 40 dB within 0 - 100% indicator. - * Weakest usable signal is usually 10 - 15 dB SNR. */ - if (noise_dbm) { - if (rssi_dbm - noise_dbm >= 40) - return 100; - else if (rssi_dbm < noise_dbm) - return 0; - sig_qual = ((rssi_dbm - noise_dbm) * 5) / 2; - - /* Else use just the signal level. - * This formula is a least squares fit of data points collected and - * compared with a reference system that had a percentage (%) display - * for signal quality. */ - } else - sig_qual = (100 * (RSSI_RANGE * RSSI_RANGE) - degradation * - (15 * RSSI_RANGE + 62 * degradation)) / - (RSSI_RANGE * RSSI_RANGE); - - if (sig_qual > 100) - sig_qual = 100; - else if (sig_qual < 1) - sig_qual = 0; - - return sig_qual; -} - /** * iwl3945_rx_handle - Main entry function for receiving responses from uCode * diff --git a/drivers/net/wireless/iwmc3200wifi/iwm.h b/drivers/net/wireless/iwmc3200wifi/iwm.h index 79ffa3b98d73..842811142bef 100644 --- a/drivers/net/wireless/iwmc3200wifi/iwm.h +++ b/drivers/net/wireless/iwmc3200wifi/iwm.h @@ -268,7 +268,7 @@ struct iwm_priv { struct sk_buff_head rx_list; struct list_head rx_tickets; - struct list_head rx_packets[IWM_RX_ID_HASH]; + struct list_head rx_packets[IWM_RX_ID_HASH + 1]; struct workqueue_struct *rx_wq; struct work_struct rx_worker; diff --git a/drivers/net/wireless/libertas/scan.c b/drivers/net/wireless/libertas/scan.c index 4a0c3e3cd3b1..220361e69cd3 100644 --- a/drivers/net/wireless/libertas/scan.c +++ b/drivers/net/wireless/libertas/scan.c @@ -567,11 +567,8 @@ int lbs_scan_networks(struct lbs_private *priv, int full_scan) chan_count = lbs_scan_create_channel_list(priv, chan_list); netif_stop_queue(priv->dev); - netif_carrier_off(priv->dev); - if (priv->mesh_dev) { + if (priv->mesh_dev) netif_stop_queue(priv->mesh_dev); - netif_carrier_off(priv->mesh_dev); - } /* Prepare to continue an interrupted scan */ lbs_deb_scan("chan_count %d, scan_channel %d\n", @@ -635,16 +632,13 @@ out2: priv->scan_channel = 0; out: - if (priv->connect_status == LBS_CONNECTED) { - netif_carrier_on(priv->dev); - if (!priv->tx_pending_len) - netif_wake_queue(priv->dev); - } - if (priv->mesh_dev && lbs_mesh_connected(priv)) { - netif_carrier_on(priv->mesh_dev); - if (!priv->tx_pending_len) - netif_wake_queue(priv->mesh_dev); - } + if (priv->connect_status == LBS_CONNECTED && !priv->tx_pending_len) + netif_wake_queue(priv->dev); + + if (priv->mesh_dev && lbs_mesh_connected(priv) && + !priv->tx_pending_len) + netif_wake_queue(priv->mesh_dev); + kfree(chan_list); lbs_deb_leave_args(LBS_DEB_SCAN, "ret %d", ret); diff --git a/drivers/net/wireless/libertas_tf/main.c b/drivers/net/wireless/libertas_tf/main.c index 15a367680f59..ba3eb0101d55 100644 --- a/drivers/net/wireless/libertas_tf/main.c +++ b/drivers/net/wireless/libertas_tf/main.c @@ -495,7 +495,6 @@ int lbtf_rx(struct lbtf_private *priv, struct sk_buff *skb) stats.band = IEEE80211_BAND_2GHZ; stats.signal = prxpd->snr; stats.noise = prxpd->nf; - stats.qual = prxpd->snr - prxpd->nf; /* Marvell rate index has a hole at value 4 */ if (prxpd->rx_rate > 4) --prxpd->rx_rate; diff --git a/drivers/net/wireless/orinoco/wext.c b/drivers/net/wireless/orinoco/wext.c index 7698fdd6a3a2..31ca241f7753 100644 --- a/drivers/net/wireless/orinoco/wext.c +++ b/drivers/net/wireless/orinoco/wext.c @@ -23,7 +23,7 @@ #define MAX_RID_LEN 1024 /* Helper routine to record keys - * Do not call from interrupt context */ + * It is called under orinoco_lock so it may not sleep */ static int orinoco_set_key(struct orinoco_private *priv, int index, enum orinoco_alg alg, const u8 *key, int key_len, const u8 *seq, int seq_len) @@ -32,14 +32,14 @@ static int orinoco_set_key(struct orinoco_private *priv, int index, kzfree(priv->keys[index].seq); if (key_len) { - priv->keys[index].key = kzalloc(key_len, GFP_KERNEL); + priv->keys[index].key = kzalloc(key_len, GFP_ATOMIC); if (!priv->keys[index].key) goto nomem; } else priv->keys[index].key = NULL; if (seq_len) { - priv->keys[index].seq = kzalloc(seq_len, GFP_KERNEL); + priv->keys[index].seq = kzalloc(seq_len, GFP_ATOMIC); if (!priv->keys[index].seq) goto free_key; } else diff --git a/drivers/net/wireless/rt2x00/rt2800usb.c b/drivers/net/wireless/rt2x00/rt2800usb.c index 411655ecaf3a..0510f020dcf5 100644 --- a/drivers/net/wireless/rt2x00/rt2800usb.c +++ b/drivers/net/wireless/rt2x00/rt2800usb.c @@ -933,6 +933,7 @@ static struct usb_device_id rt2800usb_device_table[] = { { USB_DEVICE(0x1737, 0x0070), USB_DEVICE_DATA(&rt2800usb_ops) }, { USB_DEVICE(0x1737, 0x0071), USB_DEVICE_DATA(&rt2800usb_ops) }, { USB_DEVICE(0x1737, 0x0077), USB_DEVICE_DATA(&rt2800usb_ops) }, + { USB_DEVICE(0x1737, 0x0079), USB_DEVICE_DATA(&rt2800usb_ops) }, /* Logitec */ { USB_DEVICE(0x0789, 0x0162), USB_DEVICE_DATA(&rt2800usb_ops) }, { USB_DEVICE(0x0789, 0x0163), USB_DEVICE_DATA(&rt2800usb_ops) }, diff --git a/drivers/net/wireless/wl12xx/wl1251_boot.c b/drivers/net/wireless/wl12xx/wl1251_boot.c index 2e733e7bdfd4..28a808674080 100644 --- a/drivers/net/wireless/wl12xx/wl1251_boot.c +++ b/drivers/net/wireless/wl12xx/wl1251_boot.c @@ -256,7 +256,7 @@ int wl1251_boot_run_firmware(struct wl1251 *wl) } } - if (loop >= INIT_LOOP) { + if (loop > INIT_LOOP) { wl1251_error("timeout waiting for the hardware to " "complete initialization"); return -EIO; diff --git a/drivers/net/wireless/wl12xx/wl1271_cmd.c b/drivers/net/wireless/wl12xx/wl1271_cmd.c index b5eb9edc63aa..a74259bb596b 100644 --- a/drivers/net/wireless/wl12xx/wl1271_cmd.c +++ b/drivers/net/wireless/wl12xx/wl1271_cmd.c @@ -796,7 +796,7 @@ out: return ret; } -static int wl1271_build_basic_rates(char *rates, u8 band) +static int wl1271_build_basic_rates(u8 *rates, u8 band) { u8 index = 0; @@ -823,7 +823,7 @@ static int wl1271_build_basic_rates(char *rates, u8 band) return index; } -static int wl1271_build_extended_rates(char *rates, u8 band) +static int wl1271_build_extended_rates(u8 *rates, u8 band) { u8 index = 0; diff --git a/drivers/net/wireless/zd1211rw/zd_chip.c b/drivers/net/wireless/zd1211rw/zd_chip.c index dfa1b9bc22c8..7ca95c414fa8 100644 --- a/drivers/net/wireless/zd1211rw/zd_chip.c +++ b/drivers/net/wireless/zd1211rw/zd_chip.c @@ -1325,151 +1325,11 @@ int zd_chip_set_basic_rates(struct zd_chip *chip, u16 cr_rates) return r; } -static int ofdm_qual_db(u8 status_quality, u8 zd_rate, unsigned int size) -{ - static const u16 constants[] = { - 715, 655, 585, 540, 470, 410, 360, 315, - 270, 235, 205, 175, 150, 125, 105, 85, - 65, 50, 40, 25, 15 - }; - - int i; - u32 x; - - /* It seems that their quality parameter is somehow per signal - * and is now transferred per bit. - */ - switch (zd_rate) { - case ZD_OFDM_RATE_6M: - case ZD_OFDM_RATE_12M: - case ZD_OFDM_RATE_24M: - size *= 2; - break; - case ZD_OFDM_RATE_9M: - case ZD_OFDM_RATE_18M: - case ZD_OFDM_RATE_36M: - case ZD_OFDM_RATE_54M: - size *= 4; - size /= 3; - break; - case ZD_OFDM_RATE_48M: - size *= 3; - size /= 2; - break; - default: - return -EINVAL; - } - - x = (10000 * status_quality)/size; - for (i = 0; i < ARRAY_SIZE(constants); i++) { - if (x > constants[i]) - break; - } - - switch (zd_rate) { - case ZD_OFDM_RATE_6M: - case ZD_OFDM_RATE_9M: - i += 3; - break; - case ZD_OFDM_RATE_12M: - case ZD_OFDM_RATE_18M: - i += 5; - break; - case ZD_OFDM_RATE_24M: - case ZD_OFDM_RATE_36M: - i += 9; - break; - case ZD_OFDM_RATE_48M: - case ZD_OFDM_RATE_54M: - i += 15; - break; - default: - return -EINVAL; - } - - return i; -} - -static int ofdm_qual_percent(u8 status_quality, u8 zd_rate, unsigned int size) -{ - int r; - - r = ofdm_qual_db(status_quality, zd_rate, size); - ZD_ASSERT(r >= 0); - if (r < 0) - r = 0; - - r = (r * 100)/29; - return r <= 100 ? r : 100; -} - -static unsigned int log10times100(unsigned int x) -{ - static const u8 log10[] = { - 0, - 0, 30, 47, 60, 69, 77, 84, 90, 95, 100, - 104, 107, 111, 114, 117, 120, 123, 125, 127, 130, - 132, 134, 136, 138, 139, 141, 143, 144, 146, 147, - 149, 150, 151, 153, 154, 155, 156, 157, 159, 160, - 161, 162, 163, 164, 165, 166, 167, 168, 169, 169, - 170, 171, 172, 173, 174, 174, 175, 176, 177, 177, - 178, 179, 179, 180, 181, 181, 182, 183, 183, 184, - 185, 185, 186, 186, 187, 188, 188, 189, 189, 190, - 190, 191, 191, 192, 192, 193, 193, 194, 194, 195, - 195, 196, 196, 197, 197, 198, 198, 199, 199, 200, - 200, 200, 201, 201, 202, 202, 202, 203, 203, 204, - 204, 204, 205, 205, 206, 206, 206, 207, 207, 207, - 208, 208, 208, 209, 209, 210, 210, 210, 211, 211, - 211, 212, 212, 212, 213, 213, 213, 213, 214, 214, - 214, 215, 215, 215, 216, 216, 216, 217, 217, 217, - 217, 218, 218, 218, 219, 219, 219, 219, 220, 220, - 220, 220, 221, 221, 221, 222, 222, 222, 222, 223, - 223, 223, 223, 224, 224, 224, 224, - }; - - return x < ARRAY_SIZE(log10) ? log10[x] : 225; -} - -enum { - MAX_CCK_EVM_DB = 45, -}; - -static int cck_evm_db(u8 status_quality) -{ - return (20 * log10times100(status_quality)) / 100; -} - -static int cck_snr_db(u8 status_quality) -{ - int r = MAX_CCK_EVM_DB - cck_evm_db(status_quality); - ZD_ASSERT(r >= 0); - return r; -} - -static int cck_qual_percent(u8 status_quality) -{ - int r; - - r = cck_snr_db(status_quality); - r = (100*r)/17; - return r <= 100 ? r : 100; -} - static inline u8 zd_rate_from_ofdm_plcp_header(const void *rx_frame) { return ZD_OFDM | zd_ofdm_plcp_header_rate(rx_frame); } -u8 zd_rx_qual_percent(const void *rx_frame, unsigned int size, - const struct rx_status *status) -{ - return (status->frame_status&ZD_RX_OFDM) ? - ofdm_qual_percent(status->signal_quality_ofdm, - zd_rate_from_ofdm_plcp_header(rx_frame), - size) : - cck_qual_percent(status->signal_quality_cck); -} - /** * zd_rx_rate - report zd-rate * @rx_frame - received frame diff --git a/drivers/net/wireless/zd1211rw/zd_chip.h b/drivers/net/wireless/zd1211rw/zd_chip.h index 9fd8f3508d66..f8bbf7d302ae 100644 --- a/drivers/net/wireless/zd1211rw/zd_chip.h +++ b/drivers/net/wireless/zd1211rw/zd_chip.h @@ -929,9 +929,6 @@ static inline int zd_get_beacon_interval(struct zd_chip *chip, u32 *interval) struct rx_status; -u8 zd_rx_qual_percent(const void *rx_frame, unsigned int size, - const struct rx_status *status); - u8 zd_rx_rate(const void *rx_frame, const struct rx_status *status); struct zd_mc_hash { diff --git a/drivers/net/wireless/zd1211rw/zd_mac.c b/drivers/net/wireless/zd1211rw/zd_mac.c index c4f41d0016c5..f4a4178c8d9f 100644 --- a/drivers/net/wireless/zd1211rw/zd_mac.c +++ b/drivers/net/wireless/zd1211rw/zd_mac.c @@ -828,9 +828,6 @@ int zd_mac_rx(struct ieee80211_hw *hw, const u8 *buffer, unsigned int length) stats.freq = zd_channels[_zd_chip_get_channel(&mac->chip) - 1].center_freq; stats.band = IEEE80211_BAND_2GHZ; stats.signal = status->signal_strength; - stats.qual = zd_rx_qual_percent(buffer, - length - sizeof(struct rx_status), - status); rate = zd_rx_rate(buffer, status); |