diff options
Diffstat (limited to 'drivers/iio/common')
| -rw-r--r-- | drivers/iio/common/Kconfig | 1 | ||||
| -rw-r--r-- | drivers/iio/common/Makefile | 1 | ||||
| -rw-r--r-- | drivers/iio/common/ssp_sensors/Kconfig | 16 | ||||
| -rw-r--r-- | drivers/iio/common/ssp_sensors/Makefile | 6 | ||||
| -rw-r--r-- | drivers/iio/common/ssp_sensors/ssp.h | 257 | ||||
| -rw-r--r-- | drivers/iio/common/ssp_sensors/ssp_dev.c | 712 | ||||
| -rw-r--r-- | drivers/iio/common/ssp_sensors/ssp_spi.c | 608 |
7 files changed, 1601 insertions, 0 deletions
diff --git a/drivers/iio/common/Kconfig b/drivers/iio/common/Kconfig index 0b6e97d18fa0..790f106d719c 100644 --- a/drivers/iio/common/Kconfig +++ b/drivers/iio/common/Kconfig @@ -3,4 +3,5 @@ # source "drivers/iio/common/hid-sensors/Kconfig" +source "drivers/iio/common/ssp_sensors/Kconfig" source "drivers/iio/common/st_sensors/Kconfig" diff --git a/drivers/iio/common/Makefile b/drivers/iio/common/Makefile index 3112df0060e9..b1e4d9c9591c 100644 --- a/drivers/iio/common/Makefile +++ b/drivers/iio/common/Makefile @@ -8,4 +8,5 @@ # When adding new entries keep the list in alphabetical order obj-y += hid-sensors/ +obj-y += ssp_sensors/ obj-y += st_sensors/ diff --git a/drivers/iio/common/ssp_sensors/Kconfig b/drivers/iio/common/ssp_sensors/Kconfig new file mode 100644 index 000000000000..759b975e2b40 --- /dev/null +++ b/drivers/iio/common/ssp_sensors/Kconfig @@ -0,0 +1,16 @@ +# +# SSP sensor drivers and commons configuration +# +menu "SSP Sensor Common" + +config IIO_SSP_SENSORHUB + tristate "Samsung Sensorhub driver" + depends on SPI + select MFD_CORE + help + SSP driver for sensorhub. + If you say yes here you get ssp support for sensorhub. + To compile this driver as a module, choose M here: the + module will be called sensorhub. + +endmenu diff --git a/drivers/iio/common/ssp_sensors/Makefile b/drivers/iio/common/ssp_sensors/Makefile new file mode 100644 index 000000000000..07d3d6a6763b --- /dev/null +++ b/drivers/iio/common/ssp_sensors/Makefile @@ -0,0 +1,6 @@ +# +# Makefile for SSP sensor drivers and commons. +# + +sensorhub-objs := ssp_dev.o ssp_spi.o +obj-$(CONFIG_IIO_SSP_SENSORHUB) += sensorhub.o diff --git a/drivers/iio/common/ssp_sensors/ssp.h b/drivers/iio/common/ssp_sensors/ssp.h new file mode 100644 index 000000000000..b910e91d7c0d --- /dev/null +++ b/drivers/iio/common/ssp_sensors/ssp.h @@ -0,0 +1,257 @@ +/* + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#ifndef __SSP_SENSORHUB_H__ +#define __SSP_SENSORHUB_H__ + +#include <linux/delay.h> +#include <linux/gpio.h> +#include <linux/iio/common/ssp_sensors.h> +#include <linux/iio/iio.h> +#include <linux/spi/spi.h> + +#define SSP_DEVICE_ID 0x55 + +#ifdef SSP_DBG +#define ssp_dbg(format, ...) pr_info("[SSP] "format, ##__VA_ARGS__) +#else +#define ssp_dbg(format, ...) +#endif + +#define SSP_SW_RESET_TIME 3000 +/* Sensor polling in ms */ +#define SSP_DEFAULT_POLLING_DELAY 200 +#define SSP_DEFAULT_RETRIES 3 +#define SSP_DATA_PACKET_SIZE 960 +#define SSP_HEADER_BUFFER_SIZE 4 + +enum { + SSP_KERNEL_BINARY = 0, + SSP_KERNEL_CRASHED_BINARY, +}; + +enum { + SSP_INITIALIZATION_STATE = 0, + SSP_NO_SENSOR_STATE, + SSP_ADD_SENSOR_STATE, + SSP_RUNNING_SENSOR_STATE, +}; + +/* Firmware download STATE */ +enum { + SSP_FW_DL_STATE_FAIL = -1, + SSP_FW_DL_STATE_NONE = 0, + SSP_FW_DL_STATE_NEED_TO_SCHEDULE, + SSP_FW_DL_STATE_SCHEDULED, + SSP_FW_DL_STATE_DOWNLOADING, + SSP_FW_DL_STATE_SYNC, + SSP_FW_DL_STATE_DONE, +}; + +#define SSP_INVALID_REVISION 99999 +#define SSP_INVALID_REVISION2 0xffffff + +/* AP -> SSP Instruction */ +#define SSP_MSG2SSP_INST_BYPASS_SENSOR_ADD 0xa1 +#define SSP_MSG2SSP_INST_BYPASS_SENSOR_RM 0xa2 +#define SSP_MSG2SSP_INST_REMOVE_ALL 0xa3 +#define SSP_MSG2SSP_INST_CHANGE_DELAY 0xa4 +#define SSP_MSG2SSP_INST_LIBRARY_ADD 0xb1 +#define SSP_MSG2SSP_INST_LIBRARY_REMOVE 0xb2 +#define SSP_MSG2SSP_INST_LIB_NOTI 0xb4 +#define SSP_MSG2SSP_INST_LIB_DATA 0xc1 + +#define SSP_MSG2SSP_AP_MCU_SET_GYRO_CAL 0xcd +#define SSP_MSG2SSP_AP_MCU_SET_ACCEL_CAL 0xce +#define SSP_MSG2SSP_AP_STATUS_SHUTDOWN 0xd0 +#define SSP_MSG2SSP_AP_STATUS_WAKEUP 0xd1 +#define SSP_MSG2SSP_AP_STATUS_SLEEP 0xd2 +#define SSP_MSG2SSP_AP_STATUS_RESUME 0xd3 +#define SSP_MSG2SSP_AP_STATUS_SUSPEND 0xd4 +#define SSP_MSG2SSP_AP_STATUS_RESET 0xd5 +#define SSP_MSG2SSP_AP_STATUS_POW_CONNECTED 0xd6 +#define SSP_MSG2SSP_AP_STATUS_POW_DISCONNECTED 0xd7 +#define SSP_MSG2SSP_AP_TEMPHUMIDITY_CAL_DONE 0xda +#define SSP_MSG2SSP_AP_MCU_SET_DUMPMODE 0xdb +#define SSP_MSG2SSP_AP_MCU_DUMP_CHECK 0xdc +#define SSP_MSG2SSP_AP_MCU_BATCH_FLUSH 0xdd +#define SSP_MSG2SSP_AP_MCU_BATCH_COUNT 0xdf + +#define SSP_MSG2SSP_AP_WHOAMI 0x0f +#define SSP_MSG2SSP_AP_FIRMWARE_REV 0xf0 +#define SSP_MSG2SSP_AP_SENSOR_FORMATION 0xf1 +#define SSP_MSG2SSP_AP_SENSOR_PROXTHRESHOLD 0xf2 +#define SSP_MSG2SSP_AP_SENSOR_BARCODE_EMUL 0xf3 +#define SSP_MSG2SSP_AP_SENSOR_SCANNING 0xf4 +#define SSP_MSG2SSP_AP_SET_MAGNETIC_HWOFFSET 0xf5 +#define SSP_MSG2SSP_AP_GET_MAGNETIC_HWOFFSET 0xf6 +#define SSP_MSG2SSP_AP_SENSOR_GESTURE_CURRENT 0xf7 +#define SSP_MSG2SSP_AP_GET_THERM 0xf8 +#define SSP_MSG2SSP_AP_GET_BIG_DATA 0xf9 +#define SSP_MSG2SSP_AP_SET_BIG_DATA 0xfa +#define SSP_MSG2SSP_AP_START_BIG_DATA 0xfb +#define SSP_MSG2SSP_AP_SET_MAGNETIC_STATIC_MATRIX 0xfd +#define SSP_MSG2SSP_AP_SENSOR_TILT 0xea +#define SSP_MSG2SSP_AP_MCU_SET_TIME 0xfe +#define SSP_MSG2SSP_AP_MCU_GET_TIME 0xff + +#define SSP_MSG2SSP_AP_FUSEROM 0x01 + +/* voice data */ +#define SSP_TYPE_WAKE_UP_VOICE_SERVICE 0x01 +#define SSP_TYPE_WAKE_UP_VOICE_SOUND_SOURCE_AM 0x01 +#define SSP_TYPE_WAKE_UP_VOICE_SOUND_SOURCE_GRAMMER 0x02 + +/* Factory Test */ +#define SSP_ACCELEROMETER_FACTORY 0x80 +#define SSP_GYROSCOPE_FACTORY 0x81 +#define SSP_GEOMAGNETIC_FACTORY 0x82 +#define SSP_PRESSURE_FACTORY 0x85 +#define SSP_GESTURE_FACTORY 0x86 +#define SSP_TEMPHUMIDITY_CRC_FACTORY 0x88 +#define SSP_GYROSCOPE_TEMP_FACTORY 0x8a +#define SSP_GYROSCOPE_DPS_FACTORY 0x8b +#define SSP_MCU_FACTORY 0x8c +#define SSP_MCU_SLEEP_FACTORY 0x8d + +/* SSP -> AP ACK about write CMD */ +#define SSP_MSG_ACK 0x80 /* ACK from SSP to AP */ +#define SSP_MSG_NAK 0x70 /* NAK from SSP to AP */ + +struct ssp_sensorhub_info { + char *fw_name; + char *fw_crashed_name; + unsigned int fw_rev; + const u8 * const mag_table; + const unsigned int mag_length; +}; + +/* ssp_msg options bit */ +#define SSP_RW 0 +#define SSP_INDEX 3 + +#define SSP_AP2HUB_READ 0 +#define SSP_AP2HUB_WRITE 1 +#define SSP_HUB2AP_WRITE 2 +#define SSP_AP2HUB_READY 3 +#define SSP_AP2HUB_RETURN 4 + +/** + * struct ssp_data - ssp platformdata structure + * @spi: spi device + * @sensorhub_info: info about sensorhub board specific features + * @wdt_timer: watchdog timer + * @work_wdt: watchdog work + * @work_firmware: firmware upgrade work queue + * @work_refresh: refresh work queue for reset request from MCU + * @shut_down: shut down flag + * @mcu_dump_mode: mcu dump mode for debug + * @time_syncing: time syncing indication flag + * @timestamp: previous time in ns calculated for time syncing + * @check_status: status table for each sensor + * @com_fail_cnt: communication fail count + * @reset_cnt: reset count + * @timeout_cnt: timeout count + * @available_sensors: available sensors seen by sensorhub (bit array) + * @cur_firm_rev: cached current firmware revision + * @last_resume_state: last AP resume/suspend state used to handle the PM + * state of ssp + * @last_ap_state: (obsolete) sleep notification for MCU + * @sensor_enable: sensor enable mask + * @delay_buf: data acquisition intervals table + * @batch_latency_buf: yet unknown but existing in communication protocol + * @batch_opt_buf: yet unknown but existing in communication protocol + * @accel_position: yet unknown but existing in communication protocol + * @mag_position: yet unknown but existing in communication protocol + * @fw_dl_state: firmware download state + * @comm_lock: lock protecting the handshake + * @pending_lock: lock protecting pending list and completion + * @mcu_reset_gpio: mcu reset line + * @ap_mcu_gpio: ap to mcu gpio line + * @mcu_ap_gpio: mcu to ap gpio line + * @pending_list: pending list for messages queued to be sent/read + * @sensor_devs: registered IIO devices table + * @enable_refcount: enable reference count for wdt (watchdog timer) + * @header_buffer: cache aligned buffer for packet header + */ +struct ssp_data { + struct spi_device *spi; + struct ssp_sensorhub_info *sensorhub_info; + struct timer_list wdt_timer; + struct work_struct work_wdt; + struct delayed_work work_refresh; + + bool shut_down; + bool mcu_dump_mode; + bool time_syncing; + int64_t timestamp; + + int check_status[SSP_SENSOR_MAX]; + + unsigned int com_fail_cnt; + unsigned int reset_cnt; + unsigned int timeout_cnt; + + unsigned int available_sensors; + unsigned int cur_firm_rev; + + char last_resume_state; + char last_ap_state; + + unsigned int sensor_enable; + u32 delay_buf[SSP_SENSOR_MAX]; + s32 batch_latency_buf[SSP_SENSOR_MAX]; + s8 batch_opt_buf[SSP_SENSOR_MAX]; + + int accel_position; + int mag_position; + int fw_dl_state; + + struct mutex comm_lock; + struct mutex pending_lock; + + int mcu_reset_gpio; + int ap_mcu_gpio; + int mcu_ap_gpio; + + struct list_head pending_list; + + struct iio_dev *sensor_devs[SSP_SENSOR_MAX]; + atomic_t enable_refcount; + + __le16 header_buffer[SSP_HEADER_BUFFER_SIZE / sizeof(__le16)] + ____cacheline_aligned; +}; + +void ssp_clean_pending_list(struct ssp_data *data); + +int ssp_command(struct ssp_data *data, char command, int arg); + +int ssp_send_instruction(struct ssp_data *data, u8 inst, u8 sensor_type, + u8 *send_buf, u8 length); + +int ssp_irq_msg(struct ssp_data *data); + +int ssp_get_chipid(struct ssp_data *data); + +int ssp_set_magnetic_matrix(struct ssp_data *data); + +unsigned int ssp_get_sensor_scanning_info(struct ssp_data *data); + +unsigned int ssp_get_firmware_rev(struct ssp_data *data); + +int ssp_queue_ssp_refresh_task(struct ssp_data *data, unsigned int delay); + +#endif /* __SSP_SENSORHUB_H__ */ diff --git a/drivers/iio/common/ssp_sensors/ssp_dev.c b/drivers/iio/common/ssp_sensors/ssp_dev.c new file mode 100644 index 000000000000..52d70435f5a1 --- /dev/null +++ b/drivers/iio/common/ssp_sensors/ssp_dev.c @@ -0,0 +1,712 @@ +/* + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include <linux/iio/iio.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/mfd/core.h> +#include <linux/module.h> +#include <linux/of.h> +#include <linux/of_gpio.h> +#include <linux/of_platform.h> +#include "ssp.h" + +#define SSP_WDT_TIME 10000 +#define SSP_LIMIT_RESET_CNT 20 +#define SSP_LIMIT_TIMEOUT_CNT 3 + +/* It is possible that it is max clk rate for version 1.0 of bootcode */ +#define SSP_BOOT_SPI_HZ 400000 + +/* + * These fields can look enigmatic but this structure is used mainly to flat + * some values and depends on command type. + */ +struct ssp_instruction { + __le32 a; + __le32 b; + u8 c; +} __attribute__((__packed__)); + +static const u8 ssp_magnitude_table[] = {110, 85, 171, 71, 203, 195, 0, 67, + 208, 56, 175, 244, 206, 213, 0, 92, 250, 0, 55, 48, 189, 252, 171, + 243, 13, 45, 250}; + +static const struct ssp_sensorhub_info ssp_rinato_info = { + .fw_name = "ssp_B2.fw", + .fw_crashed_name = "ssp_crashed.fw", + .fw_rev = 14052300, + .mag_table = ssp_magnitude_table, + .mag_length = ARRAY_SIZE(ssp_magnitude_table), +}; + +static const struct ssp_sensorhub_info ssp_thermostat_info = { + .fw_name = "thermostat_B2.fw", + .fw_crashed_name = "ssp_crashed.fw", + .fw_rev = 14080600, + .mag_table = ssp_magnitude_table, + .mag_length = ARRAY_SIZE(ssp_magnitude_table), +}; + +static const struct mfd_cell sensorhub_sensor_devs[] = { + { + .name = "ssp-accelerometer", + }, + { + .name = "ssp-gyroscope", + }, +}; + +static void ssp_toggle_mcu_reset_gpio(struct ssp_data *data) +{ + gpio_set_value(data->mcu_reset_gpio, 0); + usleep_range(1000, 1200); + gpio_set_value(data->mcu_reset_gpio, 1); + msleep(50); +} + +static void ssp_sync_available_sensors(struct ssp_data *data) +{ + int i, ret; + + for (i = 0; i < SSP_SENSOR_MAX; ++i) { + if (data->available_sensors & BIT(i)) { + ret = ssp_enable_sensor(data, i, data->delay_buf[i]); + if (ret < 0) { + dev_err(&data->spi->dev, + "Sync sensor nr: %d fail\n", i); + continue; + } + } + } + + ret = ssp_command(data, SSP_MSG2SSP_AP_MCU_SET_DUMPMODE, + data->mcu_dump_mode); + if (ret < 0) + dev_err(&data->spi->dev, + "SSP_MSG2SSP_AP_MCU_SET_DUMPMODE failed\n"); +} + +static void ssp_enable_mcu(struct ssp_data *data, bool enable) +{ + dev_info(&data->spi->dev, "current shutdown = %d, old = %d\n", enable, + data->shut_down); + + if (enable && data->shut_down) { + data->shut_down = false; + enable_irq(data->spi->irq); + enable_irq_wake(data->spi->irq); + } else if (!enable && !data->shut_down) { + data->shut_down = true; + disable_irq(data->spi->irq); + disable_irq_wake(data->spi->irq); + } else { + dev_warn(&data->spi->dev, "current shutdown = %d, old = %d\n", + enable, data->shut_down); + } +} + +/* + * This function is the first one which communicates with the mcu so it is + * possible that the first attempt will fail + */ +static int ssp_check_fwbl(struct ssp_data *data) +{ + int retries = 0; + + while (retries++ < 5) { + data->cur_firm_rev = ssp_get_firmware_rev(data); + if (data->cur_firm_rev == SSP_INVALID_REVISION || + data->cur_firm_rev == SSP_INVALID_REVISION2) { + dev_warn(&data->spi->dev, + "Invalid revision, trying %d time\n", retries); + } else { + break; + } + } + + if (data->cur_firm_rev == SSP_INVALID_REVISION || + data->cur_firm_rev == SSP_INVALID_REVISION2) { + dev_err(&data->spi->dev, "SSP_INVALID_REVISION\n"); + return SSP_FW_DL_STATE_NEED_TO_SCHEDULE; + } + + dev_info(&data->spi->dev, + "MCU Firm Rev : Old = %8u, New = %8u\n", + data->cur_firm_rev, + data->sensorhub_info->fw_rev); + + if (data->cur_firm_rev != data->sensorhub_info->fw_rev) + return SSP_FW_DL_STATE_NEED_TO_SCHEDULE; + + return SSP_FW_DL_STATE_NONE; +} + +static void ssp_reset_mcu(struct ssp_data *data) +{ + ssp_enable_mcu(data, false); + ssp_clean_pending_list(data); + ssp_toggle_mcu_reset_gpio(data); + ssp_enable_mcu(data, true); +} + +static void ssp_wdt_work_func(struct work_struct *work) +{ + struct ssp_data *data = container_of(work, struct ssp_data, work_wdt); + + dev_err(&data->spi->dev, "%s - Sensor state: 0x%x, RC: %u, CC: %u\n", + __func__, data->available_sensors, data->reset_cnt, + data->com_fail_cnt); + + ssp_reset_mcu(data); + data->com_fail_cnt = 0; + data->timeout_cnt = 0; +} + +static void ssp_wdt_timer_func(unsigned long ptr) +{ + struct ssp_data *data = (struct ssp_data *)ptr; + + switch (data->fw_dl_state) { + case SSP_FW_DL_STATE_FAIL: + case SSP_FW_DL_STATE_DOWNLOADING: + case SSP_FW_DL_STATE_SYNC: + goto _mod; + } + + if (data->timeout_cnt > SSP_LIMIT_TIMEOUT_CNT || + data->com_fail_cnt > SSP_LIMIT_RESET_CNT) + queue_work(system_power_efficient_wq, &data->work_wdt); +_mod: + mod_timer(&data->wdt_timer, jiffies + msecs_to_jiffies(SSP_WDT_TIME)); +} + +static void ssp_enable_wdt_timer(struct ssp_data *data) +{ + mod_timer(&data->wdt_timer, jiffies + msecs_to_jiffies(SSP_WDT_TIME)); +} + +static void ssp_disable_wdt_timer(struct ssp_data *data) +{ + del_timer_sync(&data->wdt_timer); + cancel_work_sync(&data->work_wdt); +} + +/** + * ssp_get_sensor_delay() - gets sensor data acquisition period + * @data: sensorhub structure + * @type: SSP sensor type + * + * Returns acquisition period in ms + */ +u32 ssp_get_sensor_delay(struct ssp_data *data, enum ssp_sensor_type type) +{ + return data->delay_buf[type]; +} +EXPORT_SYMBOL(ssp_get_sensor_delay); + +/** + * ssp_enable_sensor() - enables data acquisition for sensor + * @data: sensorhub structure + * @type: SSP sensor type + * @delay: delay in ms + * + * Returns 0 or negative value in case of error + */ +int ssp_enable_sensor(struct ssp_data *data, enum ssp_sensor_type type, + u32 delay) +{ + int ret; + struct ssp_instruction to_send; + + to_send.a = cpu_to_le32(delay); + to_send.b = cpu_to_le32(data->batch_latency_buf[type]); + to_send.c = data->batch_opt_buf[type]; + + switch (data->check_status[type]) { + case SSP_INITIALIZATION_STATE: + /* do calibration step, now just enable */ + case SSP_ADD_SENSOR_STATE: + ret = ssp_send_instruction(data, + SSP_MSG2SSP_INST_BYPASS_SENSOR_ADD, + type, + (u8 *)&to_send, sizeof(to_send)); + if (ret < 0) { + dev_err(&data->spi->dev, "Enabling sensor failed\n"); + data->check_status[type] = SSP_NO_SENSOR_STATE; + goto derror; + } + + data->sensor_enable |= BIT(type); + data->check_status[type] = SSP_RUNNING_SENSOR_STATE; + break; + case SSP_RUNNING_SENSOR_STATE: + ret = ssp_send_instruction(data, + SSP_MSG2SSP_INST_CHANGE_DELAY, type, + (u8 *)&to_send, sizeof(to_send)); + if (ret < 0) { + dev_err(&data->spi->dev, + "Changing sensor delay failed\n"); + goto derror; + } + break; + default: + data->check_status[type] = SSP_ADD_SENSOR_STATE; + break; + } + + data->delay_buf[type] = delay; + + if (atomic_inc_return(&data->enable_refcount) == 1) + ssp_enable_wdt_timer(data); + + return 0; + +derror: + return ret; +} +EXPORT_SYMBOL(ssp_enable_sensor); + +/** + * ssp_change_delay() - changes data acquisition for sensor + * @data: sensorhub structure + * @type: SSP sensor type + * @delay: delay in ms + * + * Returns 0 or negative value in case of error + */ +int ssp_change_delay(struct ssp_data *data, enum ssp_sensor_type type, + u32 delay) +{ + int ret; + struct ssp_instruction to_send; + + to_send.a = cpu_to_le32(delay); + to_send.b = cpu_to_le32(data->batch_latency_buf[type]); + to_send.c = data->batch_opt_buf[type]; + + ret = ssp_send_instruction(data, SSP_MSG2SSP_INST_CHANGE_DELAY, type, + (u8 *)&to_send, sizeof(to_send)); + if (ret < 0) { + dev_err(&data->spi->dev, "Changing sensor delay failed\n"); + return ret; + } + + data->delay_buf[type] = delay; + + return 0; +} +EXPORT_SYMBOL(ssp_change_delay); + +/** + * ssp_disable_sensor() - disables sensor + * + * @data: sensorhub structure + * @type: SSP sensor type + * + * Returns 0 or negative value in case of error + */ +int ssp_disable_sensor(struct ssp_data *data, enum ssp_sensor_type type) +{ + int ret; + __le32 command; + + if (data->sensor_enable & BIT(type)) { + command = cpu_to_le32(data->delay_buf[type]); + + ret = ssp_send_instruction(data, + SSP_MSG2SSP_INST_BYPASS_SENSOR_RM, + type, (u8 *)&command, + sizeof(command)); + if (ret < 0) { + dev_err(&data->spi->dev, "Remove sensor fail\n"); + return ret; + } + + data->sensor_enable &= ~BIT(type); + } + + data->check_status[type] = SSP_ADD_SENSOR_STATE; + + if (atomic_dec_and_test(&data->enable_refcount)) + ssp_disable_wdt_timer(data); + + return 0; +} +EXPORT_SYMBOL(ssp_disable_sensor); + +static irqreturn_t ssp_irq_thread_fn(int irq, void *dev_id) +{ + struct ssp_data *data = dev_id; + + /* + * This wrapper is done to preserve error path for ssp_irq_msg, also + * it is defined in different file. + */ + ssp_irq_msg(data); + + return IRQ_HANDLED; +} + +static int ssp_initialize_mcu(struct ssp_data *data) +{ + int ret; + + ssp_clean_pending_list(data); + + ret = ssp_get_chipid(data); + if (ret != SSP_DEVICE_ID) { + dev_err(&data->spi->dev, "%s - MCU %s ret = %d\n", __func__, + ret < 0 ? "is not working" : "identification failed", + ret); + return ret < 0 ? ret : -ENODEV; + } + + dev_info(&data->spi->dev, "MCU device ID = %d\n", ret); + + /* + * needs clarification, for now do not want to export all transfer + * methods to sensors' drivers + */ + ret = ssp_set_magnetic_matrix(data); + if (ret < 0) { + dev_err(&data->spi->dev, + "%s - ssp_set_magnetic_matrix failed\n", __func__); + return ret; + } + + data->available_sensors = ssp_get_sensor_scanning_info(data); + if (data->available_sensors == 0) { + dev_err(&data->spi->dev, + "%s - ssp_get_sensor_scanning_info failed\n", __func__); + return -EIO; + } + + data->cur_firm_rev = ssp_get_firmware_rev(data); + dev_info(&data->spi->dev, "MCU Firm Rev : New = %8u\n", + data->cur_firm_rev); + + return ssp_command(data, SSP_MSG2SSP_AP_MCU_DUMP_CHECK, 0); +} + +/* + * sensorhub can request its reinitialization as some brutal and rare error + * handling. It can be requested from the MCU. + */ +static void ssp_refresh_task(struct work_struct *work) +{ + struct ssp_data *data = container_of((struct delayed_work *)work, + struct ssp_data, work_refresh); + + dev_info(&data->spi->dev, "refreshing\n"); + + data->reset_cnt++; + + if (ssp_initialize_mcu(data) >= 0) { + ssp_sync_available_sensors(data); + if (data->last_ap_state != 0) + ssp_command(data, data->last_ap_state, 0); + + if (data->last_resume_state != 0) + ssp_command(data, data->last_resume_state, 0); + + data->timeout_cnt = 0; + data->com_fail_cnt = 0; + } +} + +int ssp_queue_ssp_refresh_task(struct ssp_data *data, unsigned int delay) +{ + cancel_delayed_work_sync(&data->work_refresh); + + return queue_delayed_work(system_power_efficient_wq, + &data->work_refresh, + msecs_to_jiffies(delay)); +} + +#ifdef CONFIG_OF +static struct of_device_id ssp_of_match[] = { + { + .compatible = "samsung,sensorhub-rinato", + .data = &ssp_rinato_info, + }, { + .compatible = "samsung,sensorhub-thermostat", + .data = &ssp_thermostat_info, + }, + {}, +}; +MODULE_DEVICE_TABLE(of, ssp_of_match); + +static struct ssp_data *ssp_parse_dt(struct device *dev) +{ + int ret; + struct ssp_data *data; + struct device_node *node = dev->of_node; + const struct of_device_id *match; + + data = devm_kzalloc(dev, sizeof(*data), GFP_KERNEL); + if (!data) + return NULL; + + data->mcu_ap_gpio = of_get_named_gpio(node, "mcu-ap-gpios", 0); + if (data->mcu_ap_gpio < 0) + goto err_free_pd; + + data->ap_mcu_gpio = of_get_named_gpio(node, "ap-mcu-gpios", 0); + if (data->ap_mcu_gpio < 0) + goto err_free_pd; + + data->mcu_reset_gpio = of_get_named_gpio(node, "mcu-reset-gpios", 0); + if (data->mcu_reset_gpio < 0) + goto err_free_pd; + + ret = devm_gpio_request_one(dev, data->ap_mcu_gpio, GPIOF_OUT_INIT_HIGH, + "ap-mcu-gpios"); + if (ret) + goto err_free_pd; + + ret = devm_gpio_request_one(dev, data->mcu_reset_gpio, + GPIOF_OUT_INIT_HIGH, "mcu-reset-gpios"); + if (ret) + goto err_ap_mcu; + + match = of_match_node(ssp_of_match, node); + if (!match) + goto err_mcu_reset_gpio; + + data->sensorhub_info = (struct ssp_sensorhub_info *)match->data; + + dev_set_drvdata(dev, data); + + return data; + +err_mcu_reset_gpio: + devm_gpio_free(dev, data->mcu_reset_gpio); +err_ap_mcu: + devm_gpio_free(dev, data->ap_mcu_gpio); +err_free_pd: + devm_kfree(dev, data); + return NULL; +} +#else +static struct ssp_data *ssp_parse_dt(struct device *pdev) +{ + return NULL; +} +#endif + +/** + * ssp_register_consumer() - registers iio consumer in ssp framework + * + * @indio_dev: consumer iio device + * @type: ssp sensor type + */ +void ssp_register_consumer(struct iio_dev *indio_dev, enum ssp_sensor_type type) +{ + struct ssp_data *data = dev_get_drvdata(indio_dev->dev.parent->parent); + + data->sensor_devs[type] = indio_dev; +} +EXPORT_SYMBOL(ssp_register_consumer); + +static int ssp_probe(struct spi_device *spi) +{ + int ret, i; + struct ssp_data *data; + + data = ssp_parse_dt(&spi->dev); + if (!data) { + dev_err(&spi->dev, "Failed to find platform data\n"); + return -ENODEV; + } + + ret = mfd_add_devices(&spi->dev, -1, sensorhub_sensor_devs, + ARRAY_SIZE(sensorhub_sensor_devs), NULL, 0, NULL); + if (ret < 0) { + dev_err(&spi->dev, "mfd add devices fail\n"); + return ret; + } + + spi->mode = SPI_MODE_1; + ret = spi_setup(spi); + if (ret < 0) { + dev_err(&spi->dev, "Failed to setup spi\n"); + return ret; + } + + data->fw_dl_state = SSP_FW_DL_STATE_NONE; + data->spi = spi; + spi_set_drvdata(spi, data); + + mutex_init(&data->comm_lock); + + for (i = 0; i < SSP_SENSOR_MAX; ++i) { + data->delay_buf[i] = SSP_DEFAULT_POLLING_DELAY; + data->batch_latency_buf[i] = 0; + data->batch_opt_buf[i] = 0; + data->check_status[i] = SSP_INITIALIZATION_STATE; + } + + data->delay_buf[SSP_BIO_HRM_LIB] = 100; + + data->time_syncing = true; + + mutex_init(&data->pending_lock); + INIT_LIST_HEAD(&data->pending_list); + + atomic_set(&data->enable_refcount, 0); + + INIT_WORK(&data->work_wdt, ssp_wdt_work_func); + INIT_DELAYED_WORK(&data->work_refresh, ssp_refresh_task); + + setup_timer(&data->wdt_timer, ssp_wdt_timer_func, (unsigned long)data); + + ret = request_threaded_irq(data->spi->irq, NULL, + ssp_irq_thread_fn, + IRQF_TRIGGER_FALLING | IRQF_ONESHOT, + "SSP_Int", data); + if (ret < 0) { + dev_err(&spi->dev, "Irq request fail\n"); + goto err_setup_irq; + } + + /* Let's start with enabled one so irq balance could be ok */ + data->shut_down = false; + + /* just to avoid unbalanced irq set wake up */ + enable_irq_wake(data->spi->irq); + + data->fw_dl_state = ssp_check_fwbl(data); + if (data->fw_dl_state == SSP_FW_DL_STATE_NONE) { + ret = ssp_initialize_mcu(data); + if (ret < 0) { + dev_err(&spi->dev, "Initialize_mcu failed\n"); + goto err_read_reg; + } + } else { + dev_err(&spi->dev, "Firmware version not supported\n"); + ret = -EPERM; + goto err_read_reg; + } + + return 0; + +err_read_reg: + free_irq(data->spi->irq, data); +err_setup_irq: + mutex_destroy(&data->pending_lock); + mutex_destroy(&data->comm_lock); + + dev_err(&spi->dev, "Probe failed!\n"); + + return ret; +} + +static int ssp_remove(struct spi_device *spi) +{ + struct ssp_data *data = spi_get_drvdata(spi); + + if (ssp_command(data, SSP_MSG2SSP_AP_STATUS_SHUTDOWN, 0) < 0) + dev_err(&data->spi->dev, + "SSP_MSG2SSP_AP_STATUS_SHUTDOWN failed\n"); + + ssp_enable_mcu(data, false); + ssp_disable_wdt_timer(data); + + ssp_clean_pending_list(data); + + free_irq(data->spi->irq, data); + + del_timer_sync(&data->wdt_timer); + cancel_work_sync(&data->work_wdt); + + mutex_destroy(&data->comm_lock); + mutex_destroy(&data->pending_lock); + + mfd_remove_devices(&spi->dev); + + return 0; +} + +static int ssp_suspend(struct device *dev) +{ + int ret; + struct ssp_data *data = spi_get_drvdata(to_spi_device(dev)); + + data->last_resume_state = SSP_MSG2SSP_AP_STATUS_SUSPEND; + + if (atomic_read(&data->enable_refcount) > 0) + ssp_disable_wdt_timer(data); + + ret = ssp_command(data, SSP_MSG2SSP_AP_STATUS_SUSPEND, 0); + if (ret < 0) { + dev_err(&data->spi->dev, + "%s SSP_MSG2SSP_AP_STATUS_SUSPEND failed\n", __func__); + + ssp_enable_wdt_timer(data); + return ret; + } + + data->time_syncing = false; + disable_irq(data->spi->irq); + + return 0; +} + +static int ssp_resume(struct device *dev) +{ + int ret; + struct ssp_data *data = spi_get_drvdata(to_spi_device(dev)); + + enable_irq(data->spi->irq); + + if (atomic_read(&data->enable_refcount) > 0) + ssp_enable_wdt_timer(data); + + ret = ssp_command(data, SSP_MSG2SSP_AP_STATUS_RESUME, 0); + if (ret < 0) { + dev_err(&data->spi->dev, + "%s SSP_MSG2SSP_AP_STATUS_RESUME failed\n", __func__); + ssp_disable_wdt_timer(data); + return ret; + } + + /* timesyncing is set by MCU */ + data->last_resume_state = SSP_MSG2SSP_AP_STATUS_RESUME; + + return 0; +} + +static const struct dev_pm_ops ssp_pm_ops = { + SET_SYSTEM_SLEEP_PM_OPS(ssp_suspend, ssp_resume) +}; + +static struct spi_driver ssp_driver = { + .probe = ssp_probe, + .remove = ssp_remove, + .driver = { + .pm = &ssp_pm_ops, + .bus = &spi_bus_type, + .owner = THIS_MODULE, + .of_match_table = of_match_ptr(ssp_of_match), + .name = "sensorhub" + }, +}; + +module_spi_driver(ssp_driver); + +MODULE_DESCRIPTION("ssp sensorhub driver"); +MODULE_AUTHOR("Samsung Electronics"); +MODULE_LICENSE("GPL"); diff --git a/drivers/iio/common/ssp_sensors/ssp_spi.c b/drivers/iio/common/ssp_sensors/ssp_spi.c new file mode 100644 index 000000000000..704284a475ae --- /dev/null +++ b/drivers/iio/common/ssp_sensors/ssp_spi.c @@ -0,0 +1,608 @@ +/* + * Copyright (C) 2014, Samsung Electronics Co. Ltd. All Rights Reserved. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License as published by + * the Free Software Foundation; either version 2 of the License, or + * (at your option) any later version. + * + * This program is distributed in the hope that it will be useful, + * but WITHOUT ANY WARRANTY; without even the implied warranty of + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the + * GNU General Public License for more details. + * + */ + +#include "ssp.h" + +#define SSP_DEV (&data->spi->dev) +#define SSP_GET_MESSAGE_TYPE(data) (data & (3 << SSP_RW)) + +/* + * SSP -> AP Instruction + * They tell what packet type can be expected. In the future there will + * be less of them. BYPASS means common sensor packets with accel, gyro, + * hrm etc. data. LIBRARY and META are mock-up's for now. + */ +#define SSP_MSG2AP_INST_BYPASS_DATA 0x37 +#define SSP_MSG2AP_INST_LIBRARY_DATA 0x01 +#define SSP_MSG2AP_INST_DEBUG_DATA 0x03 +#define SSP_MSG2AP_INST_BIG_DATA 0x04 +#define SSP_MSG2AP_INST_META_DATA 0x05 +#define SSP_MSG2AP_INST_TIME_SYNC 0x06 +#define SSP_MSG2AP_INST_RESET 0x07 + +#define SSP_UNIMPLEMENTED -1 + +struct ssp_msg_header { + u8 cmd; + __le16 length; + __le16 options; + __le32 data; +} __attribute__((__packed__)); + +struct ssp_msg { + u16 length; + u16 options; + struct list_head list; + struct completion *done; + struct ssp_msg_header *h; + char *buffer; +}; + +static const int ssp_offset_map[SSP_SENSOR_MAX] = { + [SSP_ACCELEROMETER_SENSOR] = SSP_ACCELEROMETER_SIZE + + SSP_TIME_SIZE, + [SSP_GYROSCOPE_SENSOR] = SSP_GYROSCOPE_SIZE + + SSP_TIME_SIZE, + [SSP_GEOMAGNETIC_UNCALIB_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_GEOMAGNETIC_RAW] = SSP_UNIMPLEMENTED, + [SSP_GEOMAGNETIC_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_PRESSURE_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_GESTURE_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_PROXIMITY_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_TEMPERATURE_HUMIDITY_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_LIGHT_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_PROXIMITY_RAW] = SSP_UNIMPLEMENTED, + [SSP_ORIENTATION_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_STEP_DETECTOR] = SSP_UNIMPLEMENTED, + [SSP_SIG_MOTION_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_GYRO_UNCALIB_SENSOR] = SSP_UNIMPLEMENTED, + [SSP_GAME_ROTATION_VECTOR] = SSP_UNIMPLEMENTED, + [SSP_ROTATION_VECTOR] = SSP_UNIMPLEMENTED, + [SSP_STEP_COUNTER] = SSP_UNIMPLEMENTED, + [SSP_BIO_HRM_RAW] = SSP_BIO_HRM_RAW_SIZE + + SSP_TIME_SIZE, + [SSP_BIO_HRM_RAW_FAC] = SSP_BIO_HRM_RAW_FAC_SIZE + + SSP_TIME_SIZE, + [SSP_BIO_HRM_LIB] = SSP_BIO_HRM_LIB_SIZE + + SSP_TIME_SIZE, +}; + +#define SSP_HEADER_SIZE (sizeof(struct ssp_msg_header)) +#define SSP_HEADER_SIZE_ALIGNED (ALIGN(SSP_HEADER_SIZE, 4)) + +static struct ssp_msg *ssp_create_msg(u8 cmd, u16 len, u16 opt, u32 data) +{ + struct ssp_msg_header h; + struct ssp_msg *msg; + + msg = kzalloc(sizeof(*msg), GFP_KERNEL); + if (!msg) + return NULL; + + h.cmd = cmd; + h.length = cpu_to_le16(len); + h.options = cpu_to_le16(opt); + h.data = cpu_to_le32(data); + + msg->buffer = kzalloc(SSP_HEADER_SIZE_ALIGNED + len, + GFP_KERNEL | GFP_DMA); + if (!msg->buffer) { + kfree(msg); + return NULL; + } + + msg->length = len; + msg->options = opt; + + memcpy(msg->buffer, &h, SSP_HEADER_SIZE); + + return msg; +} + +/* + * It is a bit heavy to do it this way but often the function is used to compose + * the message from smaller chunks which are placed on the stack. Often the + * chunks are small so memcpy should be optimalized. + */ +static inline void ssp_fill_buffer(struct ssp_msg *m, unsigned int offset, + const void *src, unsigned int len) +{ + memcpy(&m->buffer[SSP_HEADER_SIZE_ALIGNED + offset], src, len); +} + +static inline void ssp_get_buffer(struct ssp_msg *m, unsigned int offset, + void *dest, unsigned int len) +{ + memcpy(dest, &m->buffer[SSP_HEADER_SIZE_ALIGNED + offset], len); +} + +#define SSP_GET_BUFFER_AT_INDEX(m, index) \ + (m->buffer[SSP_HEADER_SIZE_ALIGNED + index]) +#define SSP_SET_BUFFER_AT_INDEX(m, index, val) \ + (m->buffer[SSP_HEADER_SIZE_ALIGNED + index] = val) + +static void ssp_clean_msg(struct ssp_msg *m) +{ + kfree(m->buffer); + kfree(m); +} + +static int ssp_print_mcu_debug(char *data_frame, int *data_index, + int received_len) +{ + int length = data_frame[(*data_index)++]; + + if (length > received_len - *data_index || length <= 0) { + ssp_dbg("[SSP]: MSG From MCU-invalid debug length(%d/%d)\n", + length, received_len); + return length ? length : -EPROTO; + } + + ssp_dbg("[SSP]: MSG From MCU - %s\n", &data_frame[*data_index]); + + *data_index += length; + + return 0; +} + +/* + * It was designed that way - additional lines to some kind of handshake, + * please do not ask why - only the firmware guy can know it. + */ +static int ssp_check_lines(struct ssp_data *data, bool state) +{ + int delay_cnt = 0; + + gpio_set_value_cansleep(data->ap_mcu_gpio, state); + + while (gpio_get_value_cansleep(data->mcu_ap_gpio) != state) { + usleep_range(3000, 3500); + + if (data->shut_down || delay_cnt++ > 500) { + dev_err(SSP_DEV, "%s:timeout, hw ack wait fail %d\n", + __func__, state); + + if (!state) + gpio_set_value_cansleep(data->ap_mcu_gpio, 1); + + return -ETIMEDOUT; + } + } + + return 0; +} + +static int ssp_do_transfer(struct ssp_data *data, struct ssp_msg *msg, + struct completion *done, int timeout) +{ + int status; + /* + * check if this is a short one way message or the whole transfer has + * second part after an interrupt + */ + const bool use_no_irq = msg->length == 0; + + if (data->shut_down) + return -EPERM; + + msg->done = done; + + mutex_lock(&data->comm_lock); + + status = ssp_check_lines(data, false); + if (status < 0) + goto _error_locked; + + status = spi_write(data->spi, msg->buffer, SSP_HEADER_SIZE); + if (status < 0) { + gpio_set_value_cansleep(data->ap_mcu_gpio, 1); + dev_err(SSP_DEV, "%s spi_write fail\n", __func__); + goto _error_locked; + } + + if (!use_no_irq) { + mutex_lock(&data->pending_lock); + list_add_tail(&msg->list, &data->pending_list); + mutex_unlock(&data->pending_lock); + } + + status = ssp_check_lines(data, true); + if (status < 0) { + if (!use_no_irq) { + mutex_lock(&data->pending_lock); + list_del(&msg->list); + mutex_unlock(&data->pending_lock); + } + goto _error_locked; + } + + mutex_unlock(&data->comm_lock); + + if (!use_no_irq && done) + if (wait_for_completion_timeout(done, + msecs_to_jiffies(timeout)) == + 0) { + mutex_lock(&data->pending_lock); + list_del(&msg->list); + mutex_unlock(&data->pending_lock); + + data->timeout_cnt++; + return -ETIMEDOUT; + } + + return 0; + +_error_locked: + mutex_unlock(&data->comm_lock); + data->timeout_cnt++; + return status; +} + +static inline int ssp_spi_sync_command(struct ssp_data *data, + struct ssp_msg *msg) +{ + return ssp_do_transfer(data, msg, NULL, 0); +} + +static int ssp_spi_sync(struct ssp_data *data, struct ssp_msg *msg, + int timeout) +{ + DECLARE_COMPLETION_ONSTACK(done); + + if (WARN_ON(!msg->length)) + return -EPERM; + + return ssp_do_transfer(data, msg, &done, timeout); +} + +static int ssp_handle_big_data(struct ssp_data *data, char *dataframe, int *idx) +{ + /* mock-up, it will be changed with adding another sensor types */ + *idx += 8; + return 0; +} + +static int ssp_parse_dataframe(struct ssp_data *data, char *dataframe, int len) +{ + int idx, sd; + struct timespec ts; + struct ssp_sensor_data *spd; + struct iio_dev **indio_devs = data->sensor_devs; + + getnstimeofday(&ts); + + for (idx = 0; idx < len;) { + switch (dataframe[idx++]) { + case SSP_MSG2AP_INST_BYPASS_DATA: + sd = dataframe[idx++]; + if (sd < 0 || sd >= SSP_SENSOR_MAX) { + dev_err(SSP_DEV, + "Mcu data frame1 error %d\n", sd); + return -EPROTO; + } + + if (indio_devs[sd]) { + spd = iio_priv(indio_devs[sd]); + if (spd->process_data) + spd->process_data(indio_devs[sd], + &dataframe[idx], + data->timestamp); + } else { + dev_err(SSP_DEV, "no client for frame\n"); + } + + idx += ssp_offset_map[sd]; + break; + case SSP_MSG2AP_INST_DEBUG_DATA: + sd = ssp_print_mcu_debug(dataframe, &idx, len); + if (sd) { + dev_err(SSP_DEV, + "Mcu data frame3 error %d\n", sd); + return sd; + } + break; + case SSP_MSG2AP_INST_LIBRARY_DATA: + idx += len; + break; + case SSP_MSG2AP_INST_BIG_DATA: + ssp_handle_big_data(data, dataframe, &idx); + break; + case SSP_MSG2AP_INST_TIME_SYNC: + data->time_syncing = true; + break; + case SSP_MSG2AP_INST_RESET: + ssp_queue_ssp_refresh_task(data, 0); + break; + } + } + + if (data->time_syncing) + data->timestamp = ts.tv_sec * 1000000000ULL + ts.tv_nsec; + + return 0; +} + +/* threaded irq */ +int ssp_irq_msg(struct ssp_data *data) +{ + bool found = false; + char *buffer; + u8 msg_type; + int ret; + u16 length, msg_options; + struct ssp_msg *msg, *n; + + ret = spi_read(data->spi, data->header_buffer, SSP_HEADER_BUFFER_SIZE); + if (ret < 0) { + dev_err(SSP_DEV, "header read fail\n"); + return ret; + } + + length = le16_to_cpu(data->header_buffer[1]); + msg_options = le16_to_cpu(data->header_buffer[0]); + + if (length == 0) { + dev_err(SSP_DEV, "length received from mcu is 0\n"); + return -EINVAL; + } + + msg_type = SSP_GET_MESSAGE_TYPE(msg_options); + + switch (msg_type) { + case SSP_AP2HUB_READ: + case SSP_AP2HUB_WRITE: + /* + * this is a small list, a few elements - the packets can be + * received with no order + */ + mutex_lock(&data->pending_lock); + list_for_each_entry_safe(msg, n, &data->pending_list, list) { + if (msg->options == msg_options) { + list_del(&msg->list); + found = true; + break; + } + } + + if (!found) { + /* + * here can be implemented dead messages handling + * but the slave should not send such ones - it is to + * check but let's handle this + */ + buffer = kmalloc(length, GFP_KERNEL | GFP_DMA); + if (!buffer) { + ret = -ENOMEM; + goto _unlock; + } + + /* got dead packet so it is always an error */ + ret = spi_read(data->spi, buffer, length); + if (ret >= 0) + ret = -EPROTO; + + kfree(buffer); + + dev_err(SSP_DEV, "No match error %x\n", + msg_options); + + goto _unlock; + } + + if (msg_type == SSP_AP2HUB_READ) + ret = spi_read(data->spi, + &msg->buffer[SSP_HEADER_SIZE_ALIGNED], + msg->length); + + if (msg_type == SSP_AP2HUB_WRITE) { + ret = spi_write(data->spi, + &msg->buffer[SSP_HEADER_SIZE_ALIGNED], + msg->length); + if (msg_options & SSP_AP2HUB_RETURN) { + msg->options = + SSP_AP2HUB_READ | SSP_AP2HUB_RETURN; + msg->length = 1; + + list_add_tail(&msg->list, &data->pending_list); + goto _unlock; + } + } + + if (msg->done) + if (!completion_done(msg->done)) + complete(msg->done); +_unlock: + mutex_unlock(&data->pending_lock); + break; + case SSP_HUB2AP_WRITE: + buffer = kzalloc(length, GFP_KERNEL | GFP_DMA); + if (!buffer) + return -ENOMEM; + + ret = spi_read(data->spi, buffer, length); + if (ret < 0) { + dev_err(SSP_DEV, "spi read fail\n"); + kfree(buffer); + break; + } + + ret = ssp_parse_dataframe(data, buffer, length); + + kfree(buffer); + break; + + default: + dev_err(SSP_DEV, "unknown msg type\n"); + return -EPROTO; + } + + return ret; +} + +void ssp_clean_pending_list(struct ssp_data *data) +{ + struct ssp_msg *msg, *n; + + mutex_lock(&data->pending_lock); + list_for_each_entry_safe(msg, n, &data->pending_list, list) { + list_del(&msg->list); + + if (msg->done) + if (!completion_done(msg->done)) + complete(msg->done); + } + mutex_unlock(&data->pending_lock); +} + +int ssp_command(struct ssp_data *data, char command, int arg) +{ + int ret; + struct ssp_msg *msg; + + msg = ssp_create_msg(command, 0, SSP_AP2HUB_WRITE, arg); + if (!msg) + return -ENOMEM; + + ssp_dbg("%s - command 0x%x %d\n", __func__, command, arg); + + ret = ssp_spi_sync_command(data, msg); + ssp_clean_msg(msg); + + return ret; +} + +int ssp_send_instruction(struct ssp_data *data, u8 inst, u8 sensor_type, + u8 *send_buf, u8 length) +{ + int ret; + struct ssp_msg *msg; + + if (data->fw_dl_state == SSP_FW_DL_STATE_DOWNLOADING) { + dev_err(SSP_DEV, "%s - Skip Inst! DL state = %d\n", + __func__, data->fw_dl_state); + return -EBUSY; + } else if (!(data->available_sensors & BIT(sensor_type)) && + (inst <= SSP_MSG2SSP_INST_CHANGE_DELAY)) { + dev_err(SSP_DEV, "%s - Bypass Inst Skip! - %u\n", + __func__, sensor_type); + return -EIO; /* just fail */ + } + + msg = ssp_create_msg(inst, length + 2, SSP_AP2HUB_WRITE, 0); + if (!msg) + return -ENOMEM; + + ssp_fill_buffer(msg, 0, &sensor_type, 1); + ssp_fill_buffer(msg, 1, send_buf, length); + + ssp_dbg("%s - Inst = 0x%x, Sensor Type = 0x%x, data = %u\n", + __func__, inst, sensor_type, send_buf[1]); + + ret = ssp_spi_sync(data, msg, 1000); + ssp_clean_msg(msg); + + return ret; +} + +int ssp_get_chipid(struct ssp_data *data) +{ + int ret; + char buffer; + struct ssp_msg *msg; + + msg = ssp_create_msg(SSP_MSG2SSP_AP_WHOAMI, 1, SSP_AP2HUB_READ, 0); + if (!msg) + return -ENOMEM; + + ret = ssp_spi_sync(data, msg, 1000); + + buffer = SSP_GET_BUFFER_AT_INDEX(msg, 0); + + ssp_clean_msg(msg); + + return ret < 0 ? ret : buffer; +} + +int ssp_set_magnetic_matrix(struct ssp_data *data) +{ + int ret; + struct ssp_msg *msg; + + msg = ssp_create_msg(SSP_MSG2SSP_AP_SET_MAGNETIC_STATIC_MATRIX, + data->sensorhub_info->mag_length, SSP_AP2HUB_WRITE, + 0); + if (!msg) + return -ENOMEM; + + ssp_fill_buffer(msg, 0, data->sensorhub_info->mag_table, + data->sensorhub_info->mag_length); + + ret = ssp_spi_sync(data, msg, 1000); + ssp_clean_msg(msg); + + return ret; +} + +unsigned int ssp_get_sensor_scanning_info(struct ssp_data *data) +{ + int ret; + __le32 result; + u32 cpu_result = 0; + + struct ssp_msg *msg = ssp_create_msg(SSP_MSG2SSP_AP_SENSOR_SCANNING, 4, + SSP_AP2HUB_READ, 0); + if (!msg) + return 0; + + ret = ssp_spi_sync(data, msg, 1000); + if (ret < 0) { + dev_err(SSP_DEV, "%s - spi read fail %d\n", __func__, ret); + goto _exit; + } + + ssp_get_buffer(msg, 0, &result, 4); + cpu_result = le32_to_cpu(result); + + dev_info(SSP_DEV, "%s state: 0x%08x\n", __func__, cpu_result); + +_exit: + ssp_clean_msg(msg); + return cpu_result; +} + +unsigned int ssp_get_firmware_rev(struct ssp_data *data) +{ + int ret; + __le32 result; + + struct ssp_msg *msg = ssp_create_msg(SSP_MSG2SSP_AP_FIRMWARE_REV, 4, + SSP_AP2HUB_READ, 0); + if (!msg) + return SSP_INVALID_REVISION; + + ret = ssp_spi_sync(data, msg, 1000); + if (ret < 0) { + dev_err(SSP_DEV, "%s - transfer fail %d\n", __func__, ret); + ret = SSP_INVALID_REVISION; + goto _exit; + } + + ssp_get_buffer(msg, 0, &result, 4); + ret = le32_to_cpu(result); + +_exit: + ssp_clean_msg(msg); + return ret; +} |