1 files changed, 255 insertions, 0 deletions
diff --git a/drivers/iio/adc/ep93xx_adc.c b/drivers/iio/adc/ep93xx_adc.c
new file mode 100644
index 000000000000..a179ac476c6d
--- /dev/null
+++ b/drivers/iio/adc/ep93xx_adc.c
@@ -0,0 +1,255 @@
+/*
+ * Driver for ADC module on the Cirrus Logic EP93xx series of SoCs
+ *
+ * Copyright (C) 2015 Alexander Sverdlin
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of the GNU General Public License version 2 as
+ * published by the Free Software Foundation.
+ *
+ * The driver uses polling to get the conversion status. According to EP93xx
+ * datasheets, reading ADCResult register starts the conversion, but user is also
+ * responsible for ensuring that delay between adjacent conversion triggers is
+ * long enough so that maximum allowed conversion rate is not exceeded. This
+ * basically renders IRQ mode unusable.
+ */
+
+#include <linux/clk.h>
+#include <linux/delay.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/iio/iio.h>
+#include <linux/io.h>
+#include <linux/irqflags.h>
+#include <linux/module.h>
+#include <linux/mutex.h>
+#include <linux/platform_device.h>
+
+/*
+ * This code could benefit from real HR Timers, but jiffy granularity would
+ * lower ADC conversion rate down to CONFIG_HZ, so we fallback to busy wait
+ * in such case.
+ *
+ * HR Timers-based version loads CPU only up to 10% during back to back ADC
+ * conversion, while busy wait-based version consumes whole CPU power.
+ */
+#ifdef CONFIG_HIGH_RES_TIMERS
+#define ep93xx_adc_delay(usmin, usmax) usleep_range(usmin, usmax)
+#else
+#define ep93xx_adc_delay(usmin, usmax) udelay(usmin)
+#endif
+
+#define EP93XX_ADC_RESULT	0x08
+#define   EP93XX_ADC_SDR	BIT(31)
+#define EP93XX_ADC_SWITCH	0x18
+#define EP93XX_ADC_SW_LOCK	0x20
+
+struct ep93xx_adc_priv {
+	struct clk *clk;
+	void __iomem *base;
+	int lastch;
+	struct mutex lock;
+};
+
+#define EP93XX_ADC_CH(index, dname, swcfg) {			\
+	.type = IIO_VOLTAGE,					\
+	.indexed = 1,						\
+	.channel = index,					\
+	.address = swcfg,					\
+	.datasheet_name = dname,				\
+	.info_mask_separate = BIT(IIO_CHAN_INFO_RAW),		\
+	.info_mask_shared_by_all = BIT(IIO_CHAN_INFO_SCALE) |	\
+				   BIT(IIO_CHAN_INFO_OFFSET),	\
+}
+
+/*
+ * Numbering scheme for channels 0..4 is defined in EP9301 and EP9302 datasheets.
+ * EP9307, EP9312 and EP9312 have 3 channels more (total 8), but the numbering is
+ * not defined. So the last three are numbered randomly, let's say.
+ */
+static const struct iio_chan_spec ep93xx_adc_channels[8] = {
+	EP93XX_ADC_CH(0, "YM",	0x608),
+	EP93XX_ADC_CH(1, "SXP",	0x680),
+	EP93XX_ADC_CH(2, "SXM",	0x640),
+	EP93XX_ADC_CH(3, "SYP",	0x620),
+	EP93XX_ADC_CH(4, "SYM",	0x610),
+	EP93XX_ADC_CH(5, "XP",	0x601),
+	EP93XX_ADC_CH(6, "XM",	0x602),
+	EP93XX_ADC_CH(7, "YP",	0x604),
+};
+
+static int ep93xx_read_raw(struct iio_dev *iiodev,
+			   struct iio_chan_spec const *channel, int *value,
+			   int *shift, long mask)
+{
+	struct ep93xx_adc_priv *priv = iio_priv(iiodev);
+	unsigned long timeout;
+	int ret;
+
+	switch (mask) {
+	case IIO_CHAN_INFO_RAW:
+		mutex_lock(&priv->lock);
+		if (priv->lastch != channel->channel) {
+			priv->lastch = channel->channel;
+			/*
+			 * Switch register is software-locked, unlocking must be
+			 * immediately followed by write
+			 */
+			local_irq_disable();
+			writel_relaxed(0xAA, priv->base + EP93XX_ADC_SW_LOCK);
+			writel_relaxed(channel->address,
+				       priv->base + EP93XX_ADC_SWITCH);
+			local_irq_enable();
+			/*
+			 * Settling delay depends on module clock and could be
+			 * 2ms or 500us
+			 */
+			ep93xx_adc_delay(2000, 2000);
+		}
+		/* Start the conversion, eventually discarding old result */
+		readl_relaxed(priv->base + EP93XX_ADC_RESULT);
+		/* Ensure maximum conversion rate is not exceeded */
+		ep93xx_adc_delay(DIV_ROUND_UP(1000000, 925),
+				 DIV_ROUND_UP(1000000, 925));
+		/* At this point conversion must be completed, but anyway... */
+		ret = IIO_VAL_INT;
+		timeout = jiffies + msecs_to_jiffies(1) + 1;
+		while (1) {
+			u32 t;
+
+			t = readl_relaxed(priv->base + EP93XX_ADC_RESULT);
+			if (t & EP93XX_ADC_SDR) {
+				*value = sign_extend32(t, 15);
+				break;
+			}
+
+			if (time_after(jiffies, timeout)) {
+				dev_err(&iiodev->dev, "Conversion timeout\n");
+				ret = -ETIMEDOUT;
+				break;
+			}
+
+			cpu_relax();
+		}
+		mutex_unlock(&priv->lock);
+		return ret;
+
+	case IIO_CHAN_INFO_OFFSET:
+		/* According to datasheet, range is -25000..25000 */
+		*value = 25000;
+		return IIO_VAL_INT;
+
+	case IIO_CHAN_INFO_SCALE:
+		/* Typical supply voltage is 3.3v */
+		*value = (1ULL << 32) * 3300 / 50000;
+		*shift = 32;
+		return IIO_VAL_FRACTIONAL_LOG2;
+	}
+
+	return -EINVAL;
+}
+
+static const struct iio_info ep93xx_adc_info = {
+	.driver_module = THIS_MODULE,
+	.read_raw = ep93xx_read_raw,
+};
+
+static int ep93xx_adc_probe(struct platform_device *pdev)
+{
+	int ret;
+	struct iio_dev *iiodev;
+	struct ep93xx_adc_priv *priv;
+	struct clk *pclk;
+	struct resource *res;
+
+	iiodev = devm_iio_device_alloc(&pdev->dev, sizeof(*priv));
+	if (!iiodev)
+		return -ENOMEM;
+	priv = iio_priv(iiodev);
+
+	res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
+	if (!res) {
+		dev_err(&pdev->dev, "Cannot obtain memory resource\n");
+		return -ENXIO;
+	}
+	priv->base = devm_ioremap_resource(&pdev->dev, res);
+	if (IS_ERR(priv->base)) {
+		dev_err(&pdev->dev, "Cannot map memory resource\n");
+		return PTR_ERR(priv->base);
+	}
+
+	iiodev->dev.parent = &pdev->dev;
+	iiodev->name = dev_name(&pdev->dev);
+	iiodev->modes = INDIO_DIRECT_MODE;
+	iiodev->info = &ep93xx_adc_info;
+	iiodev->num_channels = ARRAY_SIZE(ep93xx_adc_channels);
+	iiodev->channels = ep93xx_adc_channels;
+
+	priv->lastch = -1;
+	mutex_init(&priv->lock);
+
+	platform_set_drvdata(pdev, iiodev);
+
+	priv->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(priv->clk)) {
+		dev_err(&pdev->dev, "Cannot obtain clock\n");
+		return PTR_ERR(priv->clk);
+	}
+
+	pclk = clk_get_parent(priv->clk);
+	if (!pclk) {
+		dev_warn(&pdev->dev, "Cannot obtain parent clock\n");
+	} else {
+		/*
+		 * This is actually a place for improvement:
+		 * EP93xx ADC supports two clock divisors -- 4 and 16,
+		 * resulting in conversion rates 3750 and 925 samples per second
+		 * with 500us or 2ms settling time respectively.
+		 * One might find this interesting enough to be configurable.
+		 */
+		ret = clk_set_rate(priv->clk, clk_get_rate(pclk) / 16);
+		if (ret)
+			dev_warn(&pdev->dev, "Cannot set clock rate\n");
+		/*
+		 * We can tolerate rate setting failure because the module should
+		 * work in any case.
+		 */
+	}
+
+	ret = clk_enable(priv->clk);
+	if (ret) {
+		dev_err(&pdev->dev, "Cannot enable clock\n");
+		return ret;
+	}
+
+	ret = iio_device_register(iiodev);
+	if (ret)
+		clk_disable(priv->clk);
+
+	return ret;
+}
+
+static int ep93xx_adc_remove(struct platform_device *pdev)
+{
+	struct iio_dev *iiodev = platform_get_drvdata(pdev);
+	struct ep93xx_adc_priv *priv = iio_priv(iiodev);
+
+	iio_device_unregister(iiodev);
+	clk_disable(priv->clk);
+
+	return 0;
+}
+
+static struct platform_driver ep93xx_adc_driver = {
+	.driver = {
+		.name = "ep93xx-adc",
+	},
+	.probe = ep93xx_adc_probe,
+	.remove = ep93xx_adc_remove,
+};
+module_platform_driver(ep93xx_adc_driver);
+
+MODULE_AUTHOR("Alexander Sverdlin <alexander.sverdlin@gmail.com>");
+MODULE_DESCRIPTION("Cirrus Logic EP93XX ADC driver");
+MODULE_LICENSE("GPL");
+MODULE_ALIAS("platform:ep93xx-adc");