1 files changed, 75 insertions, 0 deletions
diff --git a/drivers/gpu/drm/i915/intel_pm.c b/drivers/gpu/drm/i915/intel_pm.c
index cbd0f3269b2d..90e42e094b13 100644
--- a/drivers/gpu/drm/i915/intel_pm.c
+++ b/drivers/gpu/drm/i915/intel_pm.c
@@ -7890,6 +7890,81 @@ int sandybridge_pcode_write(struct drm_i915_private *dev_priv,
 	return 0;
 }
 
+static bool skl_pcode_try_request(struct drm_i915_private *dev_priv, u32 mbox,
+				  u32 request, u32 reply_mask, u32 reply,
+				  u32 *status)
+{
+	u32 val = request;
+
+	*status = sandybridge_pcode_read(dev_priv, mbox, &val);
+
+	return *status || ((val & reply_mask) == reply);
+}
+
+/**
+ * skl_pcode_request - send PCODE request until acknowledgment
+ * @dev_priv: device private
+ * @mbox: PCODE mailbox ID the request is targeted for
+ * @request: request ID
+ * @reply_mask: mask used to check for request acknowledgment
+ * @reply: value used to check for request acknowledgment
+ * @timeout_base_ms: timeout for polling with preemption enabled
+ *
+ * Keep resending the @request to @mbox until PCODE acknowledges it, PCODE
+ * reports an error or an overall timeout of @timeout_base_ms+10 ms expires.
+ * The request is acknowledged once the PCODE reply dword equals @reply after
+ * applying @reply_mask. Polling is first attempted with preemption enabled
+ * for @timeout_base_ms and if this times out for another 10 ms with
+ * preemption disabled.
+ *
+ * Returns 0 on success, %-ETIMEDOUT in case of a timeout, <0 in case of some
+ * other error as reported by PCODE.
+ */
+int skl_pcode_request(struct drm_i915_private *dev_priv, u32 mbox, u32 request,
+		      u32 reply_mask, u32 reply, int timeout_base_ms)
+{
+	u32 status;
+	int ret;
+
+	WARN_ON(!mutex_is_locked(&dev_priv->rps.hw_lock));
+
+#define COND skl_pcode_try_request(dev_priv, mbox, request, reply_mask, reply, \
+				   &status)
+
+	/*
+	 * Prime the PCODE by doing a request first. Normally it guarantees
+	 * that a subsequent request, at most @timeout_base_ms later, succeeds.
+	 * _wait_for() doesn't guarantee when its passed condition is evaluated
+	 * first, so send the first request explicitly.
+	 */
+	if (COND) {
+		ret = 0;
+		goto out;
+	}
+	ret = _wait_for(COND, timeout_base_ms * 1000, 10);
+	if (!ret)
+		goto out;
+
+	/*
+	 * The above can time out if the number of requests was low (2 in the
+	 * worst case) _and_ PCODE was busy for some reason even after a
+	 * (queued) request and @timeout_base_ms delay. As a workaround retry
+	 * the poll with preemption disabled to maximize the number of
+	 * requests. Increase the timeout from @timeout_base_ms to 10ms to
+	 * account for interrupts that could reduce the number of these
+	 * requests.
+	 */
+	DRM_DEBUG_KMS("PCODE timeout, retrying with preemption disabled\n");
+	WARN_ON_ONCE(timeout_base_ms > 3);
+	preempt_disable();
+	ret = wait_for_atomic(COND, 10);
+	preempt_enable();
+
+out:
+	return ret ? ret : status;
+#undef COND
+}
+
 static int byt_gpu_freq(struct drm_i915_private *dev_priv, int val)
 {
 	/*