diff options
Diffstat (limited to 'arch')
| -rw-r--r-- | arch/x86/kernel/tsc.c | 95 |
1 files changed, 58 insertions, 37 deletions
diff --git a/arch/x86/kernel/tsc.c b/arch/x86/kernel/tsc.c index 52284d31fc9c..da033b5b3e19 100644 --- a/arch/x86/kernel/tsc.c +++ b/arch/x86/kernel/tsc.c @@ -159,9 +159,14 @@ static unsigned long calc_pmtimer_ref(u64 deltatsc, u64 pm1, u64 pm2) return (unsigned long) deltatsc; } -#define CAL_MS 50 +#define CAL_MS 10 #define CAL_LATCH (CLOCK_TICK_RATE / (1000 / CAL_MS)) -#define CAL_PIT_LOOPS 5000 +#define CAL_PIT_LOOPS 1000 + +#define CAL2_MS 50 +#define CAL2_LATCH (CLOCK_TICK_RATE / (1000 / CAL2_MS)) +#define CAL2_PIT_LOOPS 5000 + /* * Try to calibrate the TSC against the Programmable @@ -170,7 +175,7 @@ static unsigned long calc_pmtimer_ref(u64 deltatsc, u64 pm1, u64 pm2) * * Return ULONG_MAX on failure to calibrate. */ -static unsigned long pit_calibrate_tsc(void) +static unsigned long pit_calibrate_tsc(u32 latch, unsigned long ms, int loopmin) { u64 tsc, t1, t2, delta; unsigned long tscmin, tscmax; @@ -185,8 +190,8 @@ static unsigned long pit_calibrate_tsc(void) * (LSB then MSB) to begin countdown. */ outb(0xb0, 0x43); - outb(CAL_LATCH & 0xff, 0x42); - outb(CAL_LATCH >> 8, 0x42); + outb(latch & 0xff, 0x42); + outb(latch >> 8, 0x42); tsc = t1 = t2 = get_cycles(); @@ -207,18 +212,18 @@ static unsigned long pit_calibrate_tsc(void) /* * Sanity checks: * - * If we were not able to read the PIT more than PIT_MIN_LOOPS + * If we were not able to read the PIT more than loopmin * times, then we have been hit by a massive SMI * * If the maximum is 10 times larger than the minimum, * then we got hit by an SMI as well. */ - if (pitcnt < CAL_PIT_LOOPS || tscmax > 10 * tscmin) + if (pitcnt < loopmin || tscmax > 10 * tscmin) return ULONG_MAX; /* Calculate the PIT value */ delta = t2 - t1; - do_div(delta, CAL_MS); + do_div(delta, ms); return delta; } @@ -230,8 +235,8 @@ unsigned long native_calibrate_tsc(void) { u64 tsc1, tsc2, delta, ref1, ref2; unsigned long tsc_pit_min = ULONG_MAX, tsc_ref_min = ULONG_MAX; - unsigned long flags; - int hpet = is_hpet_enabled(), i; + unsigned long flags, latch, ms; + int hpet = is_hpet_enabled(), i, loopmin; /* * Run 5 calibration loops to get the lowest frequency value @@ -257,7 +262,13 @@ unsigned long native_calibrate_tsc(void) * calibration delay loop as we have to wait for a certain * amount of time anyway. */ - for (i = 0; i < 5; i++) { + + /* Preset PIT loop values */ + latch = CAL_LATCH; + ms = CAL_MS; + loopmin = CAL_PIT_LOOPS; + + for (i = 0; i < 3; i++) { unsigned long tsc_pit_khz; /* @@ -268,7 +279,7 @@ unsigned long native_calibrate_tsc(void) */ local_irq_save(flags); tsc1 = tsc_read_refs(&ref1, hpet); - tsc_pit_khz = pit_calibrate_tsc(); + tsc_pit_khz = pit_calibrate_tsc(latch, ms, loopmin); tsc2 = tsc_read_refs(&ref2, hpet); local_irq_restore(flags); @@ -290,6 +301,35 @@ unsigned long native_calibrate_tsc(void) tsc2 = calc_pmtimer_ref(tsc2, ref1, ref2); tsc_ref_min = min(tsc_ref_min, (unsigned long) tsc2); + + /* Check the reference deviation */ + delta = ((u64) tsc_pit_min) * 100; + do_div(delta, tsc_ref_min); + + /* + * If both calibration results are inside a 10% window + * then we can be sure, that the calibration + * succeeded. We break out of the loop right away. We + * use the reference value, as it is more precise. + */ + if (delta >= 90 && delta <= 110) { + printk(KERN_INFO + "TSC: PIT calibration matches %s. %d loops\n", + hpet ? "HPET" : "PMTIMER", i + 1); + return tsc_ref_min; + } + + /* + * Check whether PIT failed more than once. This + * happens in virtualized environments. We need to + * give the virtual PC a slightly longer timeframe for + * the HPET/PMTIMER to make the result precise. + */ + if (i == 1 && tsc_pit_min == ULONG_MAX) { + latch = CAL2_LATCH; + ms = CAL2_MS; + loopmin = CAL2_PIT_LOOPS; + } } /* @@ -309,7 +349,7 @@ unsigned long native_calibrate_tsc(void) /* The alternative source failed as well, disable TSC */ if (tsc_ref_min == ULONG_MAX) { printk(KERN_WARNING "TSC: HPET/PMTIMER calibration " - "failed due to SMI disturbance.\n"); + "failed.\n"); return 0; } @@ -328,37 +368,18 @@ unsigned long native_calibrate_tsc(void) /* The alternative source failed, use the PIT calibration value */ if (tsc_ref_min == ULONG_MAX) { - printk(KERN_WARNING "TSC: HPET/PMTIMER calibration failed due " - "to SMI disturbance. Using PIT calibration\n"); + printk(KERN_WARNING "TSC: HPET/PMTIMER calibration failed. " + "Using PIT calibration\n"); return tsc_pit_min; } - /* Check the reference deviation */ - delta = ((u64) tsc_pit_min) * 100; - do_div(delta, tsc_ref_min); - - /* - * If both calibration results are inside a 5% window, the we - * use the lower frequency of those as it is probably the - * closest estimate. - */ - if (delta >= 95 && delta <= 105) { - printk(KERN_INFO "TSC: PIT calibration confirmed by %s.\n", - hpet ? "HPET" : "PMTIMER"); - printk(KERN_INFO "TSC: using %s calibration value\n", - tsc_pit_min <= tsc_ref_min ? "PIT" : - hpet ? "HPET" : "PMTIMER"); - return tsc_pit_min <= tsc_ref_min ? tsc_pit_min : tsc_ref_min; - } - - printk(KERN_WARNING "TSC: PIT calibration deviates from %s: %lu %lu.\n", - hpet ? "HPET" : "PMTIMER", tsc_pit_min, tsc_ref_min); - /* * The calibration values differ too much. In doubt, we use * the PIT value as we know that there are PMTIMERs around - * running at double speed. + * running at double speed. At least we let the user know: */ + printk(KERN_WARNING "TSC: PIT calibration deviates from %s: %lu %lu.\n", + hpet ? "HPET" : "PMTIMER", tsc_pit_min, tsc_ref_min); printk(KERN_INFO "TSC: Using PIT calibration value\n"); return tsc_pit_min; } |