diff options
Diffstat (limited to 'arch/x86')
| -rw-r--r-- | arch/x86/Kconfig | 62 | ||||
| -rw-r--r-- | arch/x86/Makefile | 4 | ||||
| -rw-r--r-- | arch/x86/kernel/Makefile | 1 | ||||
| -rw-r--r-- | arch/x86/kernel/apic_32.c | 2 | ||||
| -rw-r--r-- | arch/x86/kernel/e820.c | 11 | ||||
| -rw-r--r-- | arch/x86/kernel/mpparse.c | 20 | ||||
| -rw-r--r-- | arch/x86/kernel/setup.c | 1 | ||||
| -rw-r--r-- | arch/x86/kernel/visws_quirks.c | 709 | ||||
| -rw-r--r-- | arch/x86/lguest/Kconfig | 2 | ||||
| -rw-r--r-- | arch/x86/mach-default/setup.c | 32 | ||||
| -rw-r--r-- | arch/x86/mach-visws/Makefile | 8 | ||||
| -rw-r--r-- | arch/x86/mach-visws/mpparse.c | 85 | ||||
| -rw-r--r-- | arch/x86/mach-visws/reboot.c | 55 | ||||
| -rw-r--r-- | arch/x86/mach-visws/setup.c | 183 | ||||
| -rw-r--r-- | arch/x86/mach-visws/traps.c | 69 | ||||
| -rw-r--r-- | arch/x86/mach-visws/visws_apic.c | 296 | ||||
| -rw-r--r-- | arch/x86/pci/Makefile | 4 | ||||
| -rw-r--r-- | arch/x86/pci/legacy.c | 5 | ||||
| -rw-r--r-- | arch/x86/pci/numa.c | 10 | ||||
| -rw-r--r-- | arch/x86/pci/pci.h | 1 | ||||
| -rw-r--r-- | arch/x86/pci/visws.c | 19 |
21 files changed, 826 insertions, 753 deletions
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig index 3b1b1da78dae..2cfccc987a26 100644 --- a/arch/x86/Kconfig +++ b/arch/x86/Kconfig @@ -181,12 +181,12 @@ config X86_64_SMP config X86_HT bool depends on SMP - depends on (X86_32 && !(X86_VISWS || X86_VOYAGER)) || X86_64 + depends on (X86_32 && !X86_VOYAGER) || X86_64 default y config X86_BIOS_REBOOT bool - depends on !X86_VISWS && !X86_VOYAGER + depends on !X86_VOYAGER default y config X86_TRAMPOLINE @@ -232,13 +232,13 @@ config SMP config X86_FIND_SMP_CONFIG def_bool y - depends on X86_MPPARSE || X86_VOYAGER || X86_VISWS + depends on X86_MPPARSE || X86_VOYAGER if ACPI config X86_MPPARSE def_bool y bool "Enable MPS table" - depends on X86_LOCAL_APIC && !X86_VISWS + depends on X86_LOCAL_APIC help For old smp systems that do not have proper acpi support. Newer systems (esp with 64bit cpus) with acpi support, MADT and DSDT will override it @@ -247,7 +247,7 @@ endif if !ACPI config X86_MPPARSE def_bool y - depends on X86_LOCAL_APIC && !X86_VISWS + depends on X86_LOCAL_APIC endif choice @@ -281,18 +281,6 @@ config X86_VOYAGER If you do not specifically know you have a Voyager based machine, say N here, otherwise the kernel you build will not be bootable. -config X86_VISWS - bool "SGI 320/540 (Visual Workstation)" - depends on X86_32 && PCI - help - The SGI Visual Workstation series is an IA32-based workstation - based on SGI systems chips with some legacy PC hardware attached. - - Say Y here to create a kernel to run on the SGI 320 or 540. - - A kernel compiled for the Visual Workstation will not run on PCs - and vice versa. See <file:Documentation/sgi-visws.txt> for details. - config X86_GENERICARCH bool "Generic architecture" depends on X86_32 @@ -363,6 +351,18 @@ config X86_VSMP endchoice +config X86_VISWS + bool "SGI 320/540 (Visual Workstation)" + depends on X86_32 && PCI && !X86_VOYAGER && X86_MPPARSE && PCI_GODIRECT + help + The SGI Visual Workstation series is an IA32-based workstation + based on SGI systems chips with some legacy PC hardware attached. + + Say Y here to create a kernel to run on the SGI 320 or 540. + + A kernel compiled for the Visual Workstation will run on general + PCs as well. See <file:Documentation/sgi-visws.txt> for details. + config SCHED_NO_NO_OMIT_FRAME_POINTER def_bool y prompt "Single-depth WCHAN output" @@ -391,7 +391,7 @@ config VMI bool "VMI Guest support" select PARAVIRT depends on X86_32 - depends on !(X86_VISWS || X86_VOYAGER) + depends on !X86_VOYAGER help VMI provides a paravirtualized interface to the VMware ESX server (it could be used by other hypervisors in theory too, but is not @@ -402,7 +402,7 @@ config KVM_CLOCK bool "KVM paravirtualized clock" select PARAVIRT select PARAVIRT_CLOCK - depends on !(X86_VISWS || X86_VOYAGER) + depends on !X86_VOYAGER help Turning on this option will allow you to run a paravirtualized clock when running over the KVM hypervisor. Instead of relying on a PIT @@ -413,7 +413,7 @@ config KVM_CLOCK config KVM_GUEST bool "KVM Guest support" select PARAVIRT - depends on !(X86_VISWS || X86_VOYAGER) + depends on !X86_VOYAGER help This option enables various optimizations for running under the KVM hypervisor. @@ -422,7 +422,7 @@ source "arch/x86/lguest/Kconfig" config PARAVIRT bool "Enable paravirtualization code" - depends on !(X86_VISWS || X86_VOYAGER) + depends on !X86_VOYAGER help This changes the kernel so it can modify itself when it is run under a hypervisor, potentially improving performance significantly @@ -628,7 +628,7 @@ source "kernel/Kconfig.preempt" config X86_UP_APIC bool "Local APIC support on uniprocessors" - depends on X86_32 && !SMP && !(X86_VISWS || X86_VOYAGER || X86_GENERICARCH) + depends on X86_32 && !SMP && !(X86_VOYAGER || X86_GENERICARCH) help A local APIC (Advanced Programmable Interrupt Controller) is an integrated interrupt controller in the CPU. If you have a single-CPU @@ -653,11 +653,11 @@ config X86_UP_IOAPIC config X86_LOCAL_APIC def_bool y - depends on X86_64 || (X86_32 && (X86_UP_APIC || ((X86_VISWS || SMP) && !X86_VOYAGER) || X86_GENERICARCH)) + depends on X86_64 || (X86_32 && (X86_UP_APIC || (SMP && !X86_VOYAGER) || X86_GENERICARCH)) config X86_IO_APIC def_bool y - depends on X86_64 || (X86_32 && (X86_UP_IOAPIC || (SMP && !(X86_VISWS || X86_VOYAGER)) || X86_GENERICARCH)) + depends on X86_64 || (X86_32 && (X86_UP_IOAPIC || (SMP && !X86_VOYAGER) || X86_GENERICARCH)) config X86_VISWS_APIC def_bool y @@ -711,7 +711,7 @@ config X86_MCE_NONFATAL config X86_MCE_P4THERMAL bool "check for P4 thermal throttling interrupt." - depends on X86_32 && X86_MCE && (X86_UP_APIC || SMP) && !X86_VISWS + depends on X86_32 && X86_MCE && (X86_UP_APIC || SMP) help Enabling this feature will cause a message to be printed when the P4 enters thermal throttling. @@ -1414,7 +1414,7 @@ config X86_APM_BOOT menuconfig APM tristate "APM (Advanced Power Management) BIOS support" - depends on X86_32 && PM_SLEEP && !X86_VISWS + depends on X86_32 && PM_SLEEP ---help--- APM is a BIOS specification for saving power using several different techniques. This is mostly useful for battery powered laptops with @@ -1561,7 +1561,7 @@ config PCI choice prompt "PCI access mode" - depends on X86_32 && PCI && !X86_VISWS + depends on X86_32 && PCI default PCI_GOANY ---help--- On PCI systems, the BIOS can be used to detect the PCI devices and @@ -1598,12 +1598,12 @@ endchoice config PCI_BIOS def_bool y - depends on X86_32 && !X86_VISWS && PCI && (PCI_GOBIOS || PCI_GOANY) + depends on X86_32 && PCI && (PCI_GOBIOS || PCI_GOANY) # x86-64 doesn't support PCI BIOS access from long mode so always go direct. config PCI_DIRECT def_bool y - depends on PCI && (X86_64 || (PCI_GODIRECT || PCI_GOANY || PCI_GOOLPC) || X86_VISWS) + depends on PCI && (X86_64 || (PCI_GODIRECT || PCI_GOANY || PCI_GOOLPC)) config PCI_MMCONFIG def_bool y @@ -1663,7 +1663,7 @@ if X86_32 config ISA bool "ISA support" - depends on !(X86_VOYAGER || X86_VISWS) + depends on !X86_VOYAGER help Find out whether you have ISA slots on your motherboard. ISA is the name of a bus system, i.e. the way the CPU talks to the other stuff @@ -1690,7 +1690,7 @@ config EISA source "drivers/eisa/Kconfig" config MCA - bool "MCA support" if !(X86_VISWS || X86_VOYAGER) + bool "MCA support" if !X86_VOYAGER default y if X86_VOYAGER help MicroChannel Architecture is found in some IBM PS/2 machines and diff --git a/arch/x86/Makefile b/arch/x86/Makefile index b03d24b44bf9..919ce21ea654 100644 --- a/arch/x86/Makefile +++ b/arch/x86/Makefile @@ -113,10 +113,6 @@ mcore-y := arch/x86/mach-default/ mflags-$(CONFIG_X86_VOYAGER) := -Iinclude/asm-x86/mach-voyager mcore-$(CONFIG_X86_VOYAGER) := arch/x86/mach-voyager/ -# VISWS subarch support -mflags-$(CONFIG_X86_VISWS) := -Iinclude/asm-x86/mach-visws -mcore-$(CONFIG_X86_VISWS) := arch/x86/mach-visws/ - # generic subarchitecture mflags-$(CONFIG_X86_GENERICARCH):= -Iinclude/asm-x86/mach-generic fcore-$(CONFIG_X86_GENERICARCH) += arch/x86/mach-generic/ diff --git a/arch/x86/kernel/Makefile b/arch/x86/kernel/Makefile index 4033d8dc745b..55ff016e9f69 100644 --- a/arch/x86/kernel/Makefile +++ b/arch/x86/kernel/Makefile @@ -19,6 +19,7 @@ obj-y := process_$(BITS).o signal_$(BITS).o entry_$(BITS).o obj-y += traps_$(BITS).o irq_$(BITS).o obj-y += time_$(BITS).o ioport.o ldt.o obj-y += setup.o i8259.o irqinit_$(BITS).o setup_percpu.o +obj-$(CONFIG_X86_VISWS) += visws_quirks.o obj-$(CONFIG_X86_32) += probe_roms_32.o obj-$(CONFIG_X86_32) += sys_i386_32.o i386_ksyms_32.o obj-$(CONFIG_X86_64) += sys_x86_64.o x8664_ksyms_64.o diff --git a/arch/x86/kernel/apic_32.c b/arch/x86/kernel/apic_32.c index 3e947208b9d9..3e58b676d23b 100644 --- a/arch/x86/kernel/apic_32.c +++ b/arch/x86/kernel/apic_32.c @@ -974,7 +974,7 @@ void __cpuinit setup_local_APIC(void) * Double-check whether this APIC is really registered. */ if (!apic_id_registered()) - BUG(); + WARN_ON_ONCE(1); /* * Intel recommends to set DFR, LDR and TPR before enabling diff --git a/arch/x86/kernel/e820.c b/arch/x86/kernel/e820.c index 9f5002e0b35c..a5383ae2cbe3 100644 --- a/arch/x86/kernel/e820.c +++ b/arch/x86/kernel/e820.c @@ -1313,6 +1313,11 @@ void __init e820_reserve_resources(void) } } +/* + * Non-standard memory setup can be specified via this quirk: + */ +char * (*arch_memory_setup_quirk)(void); + char *__init default_machine_specific_memory_setup(void) { char *who = "BIOS-e820"; @@ -1353,6 +1358,12 @@ char *__init default_machine_specific_memory_setup(void) char *__init __attribute__((weak)) machine_specific_memory_setup(void) { + if (arch_memory_setup_quirk) { + char *who = arch_memory_setup_quirk(); + + if (who) + return who; + } return default_machine_specific_memory_setup(); } diff --git a/arch/x86/kernel/mpparse.c b/arch/x86/kernel/mpparse.c index 8b6b1e05c306..3b25e49380c6 100644 --- a/arch/x86/kernel/mpparse.c +++ b/arch/x86/kernel/mpparse.c @@ -726,12 +726,22 @@ static inline void __init construct_default_ISA_mptable(int mpc_default_type) static struct intel_mp_floating *mpf_found; /* + * Machine specific quirk for finding the SMP config before other setup + * activities destroy the table: + */ +int (*mach_get_smp_config_quirk)(unsigned int early); + +/* * Scan the memory blocks for an SMP configuration block. */ -static void __init __get_smp_config(unsigned early) +static void __init __get_smp_config(unsigned int early) { struct intel_mp_floating *mpf = mpf_found; + if (mach_get_smp_config_quirk) { + if (mach_get_smp_config_quirk(early)) + return; + } if (acpi_lapic && early) return; /* @@ -889,10 +899,16 @@ static int __init smp_scan_config(unsigned long base, unsigned long length, return 0; } -static void __init __find_smp_config(unsigned reserve) +int (*mach_find_smp_config_quirk)(unsigned int reserve); + +static void __init __find_smp_config(unsigned int reserve) { unsigned int address; + if (mach_find_smp_config_quirk) { + if (mach_find_smp_config_quirk(reserve)) + return; + } /* * FIXME: Linux assumes you have 640K of base ram.. * this continues the error... diff --git a/arch/x86/kernel/setup.c b/arch/x86/kernel/setup.c index 86fc2d624270..987b6fde3a99 100644 --- a/arch/x86/kernel/setup.c +++ b/arch/x86/kernel/setup.c @@ -596,6 +596,7 @@ void __init setup_arch(char **cmdline_p) { #ifdef CONFIG_X86_32 memcpy(&boot_cpu_data, &new_cpu_data, sizeof(new_cpu_data)); + visws_early_detect(); pre_setup_arch_hook(); early_cpu_init(); #else diff --git a/arch/x86/kernel/visws_quirks.c b/arch/x86/kernel/visws_quirks.c new file mode 100644 index 000000000000..e94bdb6add1d --- /dev/null +++ b/arch/x86/kernel/visws_quirks.c @@ -0,0 +1,709 @@ +/* + * SGI Visual Workstation support and quirks, unmaintained. + * + * Split out from setup.c by davej@suse.de + * + * Copyright (C) 1999 Bent Hagemark, Ingo Molnar + * + * SGI Visual Workstation interrupt controller + * + * The Cobalt system ASIC in the Visual Workstation contains a "Cobalt" APIC + * which serves as the main interrupt controller in the system. Non-legacy + * hardware in the system uses this controller directly. Legacy devices + * are connected to the PIIX4 which in turn has its 8259(s) connected to + * a of the Cobalt APIC entry. + * + * 09/02/2000 - Updated for 2.4 by jbarnes@sgi.com + * + * 25/11/2002 - Updated for 2.5 by Andrey Panin <pazke@orbita1.ru> + */ +#include <linux/interrupt.h> +#include <linux/module.h> +#include <linux/init.h> +#include <linux/smp.h> + +#include <asm/visws/cobalt.h> +#include <asm/visws/piix4.h> +#include <asm/arch_hooks.h> +#include <asm/fixmap.h> +#include <asm/reboot.h> +#include <asm/setup.h> +#include <asm/e820.h> +#include <asm/smp.h> +#include <asm/io.h> + +#include <mach_ipi.h> + +#include "mach_apic.h" + +#include <linux/init.h> +#include <linux/smp.h> + +#include <linux/kernel_stat.h> +#include <linux/interrupt.h> +#include <linux/init.h> + +#include <asm/io.h> +#include <asm/apic.h> +#include <asm/i8259.h> +#include <asm/irq_vectors.h> +#include <asm/visws/cobalt.h> +#include <asm/visws/lithium.h> +#include <asm/visws/piix4.h> + +#include <linux/sched.h> +#include <linux/kernel.h> +#include <linux/init.h> +#include <linux/pci.h> +#include <linux/pci_ids.h> + +extern int no_broadcast; + +#include <asm/io.h> +#include <asm/apic.h> +#include <asm/arch_hooks.h> +#include <asm/visws/cobalt.h> +#include <asm/visws/lithium.h> + +char visws_board_type = -1; +char visws_board_rev = -1; + +int is_visws_box(void) +{ + return visws_board_type >= 0; +} + +static int __init visws_time_init_quirk(void) +{ + printk(KERN_INFO "Starting Cobalt Timer system clock\n"); + + /* Set the countdown value */ + co_cpu_write(CO_CPU_TIMEVAL, CO_TIME_HZ/HZ); + + /* Start the timer */ + co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) | CO_CTRL_TIMERUN); + + /* Enable (unmask) the timer interrupt */ + co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) & ~CO_CTRL_TIMEMASK); + + /* + * Zero return means the generic timer setup code will set up + * the standard vector: + */ + return 0; +} + +static int __init visws_pre_intr_init_quirk(void) +{ + init_VISWS_APIC_irqs(); + + /* + * We dont want ISA irqs to be set up by the generic code: + */ + return 1; +} + +/* Quirk for machine specific memory setup. */ + +#define MB (1024 * 1024) + +unsigned long sgivwfb_mem_phys; +unsigned long sgivwfb_mem_size; +EXPORT_SYMBOL(sgivwfb_mem_phys); +EXPORT_SYMBOL(sgivwfb_mem_size); + +long long mem_size __initdata = 0; + +static char * __init visws_memory_setup_quirk(void) +{ + long long gfx_mem_size = 8 * MB; + + mem_size = boot_params.alt_mem_k; + + if (!mem_size) { + printk(KERN_WARNING "Bootloader didn't set memory size, upgrade it !\n"); + mem_size = 128 * MB; + } + + /* + * this hardcodes the graphics memory to 8 MB + * it really should be sized dynamically (or at least + * set as a boot param) + */ + if (!sgivwfb_mem_size) { + printk(KERN_WARNING "Defaulting to 8 MB framebuffer size\n"); + sgivwfb_mem_size = 8 * MB; + } + + /* + * Trim to nearest MB + */ + sgivwfb_mem_size &= ~((1 << 20) - 1); + sgivwfb_mem_phys = mem_size - gfx_mem_size; + + e820_add_region(0, LOWMEMSIZE(), E820_RAM); + e820_add_region(HIGH_MEMORY, mem_size - sgivwfb_mem_size - HIGH_MEMORY, E820_RAM); + e820_add_region(sgivwfb_mem_phys, sgivwfb_mem_size, E820_RESERVED); + + return "PROM"; +} + +static void visws_machine_emergency_restart(void) +{ + /* + * Visual Workstations restart after this + * register is poked on the PIIX4 + */ + outb(PIIX4_RESET_VAL, PIIX4_RESET_PORT); +} + +static void visws_machine_power_off(void) +{ + unsigned short pm_status; +/* extern unsigned int pci_bus0; */ + + while ((pm_status = inw(PMSTS_PORT)) & 0x100) + outw(pm_status, PMSTS_PORT); + + outw(PM_SUSPEND_ENABLE, PMCNTRL_PORT); + + mdelay(10); + +#define PCI_CONF1_ADDRESS(bus, devfn, reg) \ + (0x80000000 | (bus << 16) | (devfn << 8) | (reg & ~3)) + +/* outl(PCI_CONF1_ADDRESS(pci_bus0, SPECIAL_DEV, SPECIAL_REG), 0xCF8); */ + outl(PIIX_SPECIAL_STOP, 0xCFC); +} + +static int __init visws_get_smp_config_quirk(unsigned int early) +{ + /* + * Prevent MP-table parsing by the generic code: + */ + return 1; +} + +extern unsigned int __cpuinitdata maxcpus; + +/* + * The Visual Workstation is Intel MP compliant in the hardware + * sense, but it doesn't have a BIOS(-configuration table). + * No problem for Linux. + */ + +static void __init MP_processor_info (struct mpc_config_processor *m) +{ + int ver, logical_apicid; + physid_mask_t apic_cpus; + + if (!(m->mpc_cpuflag & CPU_ENABLED)) + return; + + logical_apicid = m->mpc_apicid; + printk(KERN_INFO "%sCPU #%d %u:%u APIC version %d\n", + m->mpc_cpuflag & CPU_BOOTPROCESSOR ? "Bootup " : "", + m->mpc_apicid, + (m->mpc_cpufeature & CPU_FAMILY_MASK) >> 8, + (m->mpc_cpufeature & CPU_MODEL_MASK) >> 4, + m->mpc_apicver); + + if (m->mpc_cpuflag & CPU_BOOTPROCESSOR) + boot_cpu_physical_apicid = m->mpc_apicid; + + ver = m->mpc_apicver; + if ((ver >= 0x14 && m->mpc_apicid >= 0xff) || m->mpc_apicid >= 0xf) { + printk(KERN_ERR "Processor #%d INVALID. (Max ID: %d).\n", + m->mpc_apicid, MAX_APICS); + return; + } + + apic_cpus = apicid_to_cpu_present(m->mpc_apicid); + physids_or(phys_cpu_present_map, phys_cpu_present_map, apic_cpus); + /* + * Validate version + */ + if (ver == 0x0) { + printk(KERN_ERR "BIOS bug, APIC version is 0 for CPU#%d! " + "fixing up to 0x10. (tell your hw vendor)\n", + m->mpc_apicid); + ver = 0x10; + } + apic_version[m->mpc_apicid] = ver; +} + +int __init visws_find_smp_config_quirk(unsigned int reserve) +{ + struct mpc_config_processor *mp = phys_to_virt(CO_CPU_TAB_PHYS); + unsigned short ncpus = readw(phys_to_virt(CO_CPU_NUM_PHYS)); + + if (ncpus > CO_CPU_MAX) { + printk(KERN_WARNING "find_visws_smp: got cpu count of %d at %p\n", + ncpus, mp); + + ncpus = CO_CPU_MAX; + } + + if (ncpus > maxcpus) + ncpus = maxcpus; + +#ifdef CONFIG_X86_LOCAL_APIC + smp_found_config = 1; +#endif + while (ncpus--) + MP_processor_info(mp++); + + mp_lapic_addr = APIC_DEFAULT_PHYS_BASE; + + return 1; +} + +extern int visws_trap_init_quirk(void); + +void __init visws_early_detect(void) +{ + int raw; + + visws_board_type = (char)(inb_p(PIIX_GPI_BD_REG) & PIIX_GPI_BD_REG) + >> PIIX_GPI_BD_SHIFT; + + if (visws_board_type < 0) + return; + + /* + * Install special quirks for timer, interrupt and memory setup: + */ + arch_time_init_quirk = visws_time_init_quirk; + arch_pre_intr_init_quirk = visws_pre_intr_init_quirk; + arch_memory_setup_quirk = visws_memory_setup_quirk; + + /* + * Fall back to generic behavior for traps: + */ + arch_intr_init_quirk = NULL; + arch_trap_init_quirk = visws_trap_init_quirk; + + /* + * Install reboot quirks: + */ + pm_power_off = visws_machine_power_off; + machine_ops.emergency_restart = visws_machine_emergency_restart; + + /* + * Do not use broadcast IPIs: + */ + no_broadcast = 0; + + /* + * Override generic MP-table parsing: + */ + mach_get_smp_config_quirk = visws_get_smp_config_quirk; + mach_find_smp_config_quirk = visws_find_smp_config_quirk; + +#ifdef CONFIG_X86_IO_APIC + /* + * Turn off IO-APIC detection and initialization: + */ + skip_ioapic_setup = 1; +#endif + + /* + * Get Board rev. + * First, we have to initialize the 307 part to allow us access + * to the GPIO registers. Let's map them at 0x0fc0 which is right + * after the PIIX4 PM section. + */ + outb_p(SIO_DEV_SEL, SIO_INDEX); + outb_p(SIO_GP_DEV, SIO_DATA); /* Talk to GPIO regs. */ + + outb_p(SIO_DEV_MSB, SIO_INDEX); + outb_p(SIO_GP_MSB, SIO_DATA); /* MSB of GPIO base address */ + + outb_p(SIO_DEV_LSB, SIO_INDEX); + outb_p(SIO_GP_LSB, SIO_DATA); /* LSB of GPIO base address */ + + outb_p(SIO_DEV_ENB, SIO_INDEX); + outb_p(1, SIO_DATA); /* Enable GPIO registers. */ + + /* + * Now, we have to map the power management section to write + * a bit which enables access to the GPIO registers. + * What lunatic came up with this shit? + */ + outb_p(SIO_DEV_SEL, SIO_INDEX); + outb_p(SIO_PM_DEV, SIO_DATA); /* Talk to GPIO regs. */ + + outb_p(SIO_DEV_MSB, SIO_INDEX); + outb_p(SIO_PM_MSB, SIO_DATA); /* MSB of PM base address */ + + outb_p(SIO_DEV_LSB, SIO_INDEX); + outb_p(SIO_PM_LSB, SIO_DATA); /* LSB of PM base address */ + + outb_p(SIO_DEV_ENB, SIO_INDEX); + outb_p(1, SIO_DATA); /* Enable PM registers. */ + + /* + * Now, write the PM register which enables the GPIO registers. + */ + outb_p(SIO_PM_FER2, SIO_PM_INDEX); + outb_p(SIO_PM_GP_EN, SIO_PM_DATA); + + /* + * Now, initialize the GPIO registers. + * We want them all to be inputs which is the + * power on default, so let's leave them alone. + * So, let's just read the board rev! + */ + raw = inb_p(SIO_GP_DATA1); + raw &= 0x7f; /* 7 bits of valid board revision ID. */ + + if (visws_board_type == VISWS_320) { + if (raw < 0x6) { + visws_board_rev = 4; + } else if (raw < 0xc) { + visws_board_rev = 5; + } else { + visws_board_rev = 6; + } + } else if (visws_board_type == VISWS_540) { + visws_board_rev = 2; + } else { + visws_board_rev = raw; + } + + printk(KERN_INFO "Silicon Graphics Visual Workstation %s (rev %d) detected\n", + (visws_board_type == VISWS_320 ? "320" : + (visws_board_type == VISWS_540 ? "540" : + "unknown")), visws_board_rev); +} + +#define A01234 (LI_INTA_0 | LI_INTA_1 | LI_INTA_2 | LI_INTA_3 | LI_INTA_4) +#define BCD (LI_INTB | LI_INTC | LI_INTD) +#define ALLDEVS (A01234 | BCD) + +static __init void lithium_init(void) +{ + set_fixmap(FIX_LI_PCIA, LI_PCI_A_PHYS); + set_fixmap(FIX_LI_PCIB, LI_PCI_B_PHYS); + + if ((li_pcia_read16(PCI_VENDOR_ID) != PCI_VENDOR_ID_SGI) || + (li_pcia_read16(PCI_DEVICE_ID) != PCI_DEVICE_ID_SGI_LITHIUM)) { + printk(KERN_EMERG "Lithium hostbridge %c not found\n", 'A'); +/* panic("This machine is not SGI Visual Workstation 320/540"); */ + } + + if ((li_pcib_read16(PCI_VENDOR_ID) != PCI_VENDOR_ID_SGI) || + (li_pcib_read16(PCI_DEVICE_ID) != PCI_DEVICE_ID_SGI_LITHIUM)) { + printk(KERN_EMERG "Lithium hostbridge %c not found\n", 'B'); +/* panic("This machine is not SGI Visual Workstation 320/540"); */ + } + + li_pcia_write16(LI_PCI_INTEN, ALLDEVS); + li_pcib_write16(LI_PCI_INTEN, ALLDEVS); +} + +static __init void cobalt_init(void) +{ + /* + * On normal SMP PC this is used only with SMP, but we have to + * use it and set it up here to start the Cobalt clock + */ + set_fixmap(FIX_APIC_BASE, APIC_DEFAULT_PHYS_BASE); + setup_local_APIC(); + printk(KERN_INFO "Local APIC Version %#x, ID %#x\n", + (unsigned int)apic_read(APIC_LVR), + (unsigned int)apic_read(APIC_ID)); + + set_fixmap(FIX_CO_CPU, CO_CPU_PHYS); + set_fixmap(FIX_CO_APIC, CO_APIC_PHYS); + printk(KERN_INFO "Cobalt Revision %#lx, APIC ID %#lx\n", + co_cpu_read(CO_CPU_REV), co_apic_read(CO_APIC_ID)); + + /* Enable Cobalt APIC being careful to NOT change the ID! */ + co_apic_write(CO_APIC_ID, co_apic_read(CO_APIC_ID) | CO_APIC_ENABLE); + + printk(KERN_INFO "Cobalt APIC enabled: ID reg %#lx\n", + co_apic_read(CO_APIC_ID)); +} + +int __init visws_trap_init_quirk(void) +{ + lithium_init(); + cobalt_init(); + + return 1; +} + +/* + * IRQ controller / APIC support: + */ + +static DEFINE_SPINLOCK(cobalt_lock); + +/* + * Set the given Cobalt APIC Redirection Table entry to point + * to the given IDT vector/index. + */ +static inline void co_apic_set(int entry, int irq) +{ + co_apic_write(CO_APIC_LO(entry), CO_APIC_LEVEL | (irq + FIRST_EXTERNAL_VECTOR)); + co_apic_write(CO_APIC_HI(entry), 0); +} + +/* + * Cobalt (IO)-APIC functions to handle PCI devices. + */ +static inline int co_apic_ide0_hack(void) +{ + extern char visws_board_type; + extern char visws_board_rev; + + if (visws_board_type == VISWS_320 && visws_board_rev == 5) + return 5; + return CO_APIC_IDE0; +} + +static int is_co_apic(unsigned int irq) +{ + if (IS_CO_APIC(irq)) + return CO_APIC(irq); + + switch (irq) { + case 0: return CO_APIC_CPU; + case CO_IRQ_IDE0: return co_apic_ide0_hack(); + case CO_IRQ_IDE1: return CO_APIC_IDE1; + default: return -1; + } +} + + +/* + * This is the SGI Cobalt (IO-)APIC: + */ + +static void enable_cobalt_irq(unsigned int irq) +{ + co_apic_set(is_co_apic(irq), irq); +} + +static void disable_cobalt_irq(unsigned int irq) +{ + int entry = is_co_apic(irq); + + co_apic_write(CO_APIC_LO(entry), CO_APIC_MASK); + co_apic_read(CO_APIC_LO(entry)); +} + +/* + * "irq" really just serves to identify the device. Here is where we + * map this to the Cobalt APIC entry where it's physically wired. + * This is called via request_irq -> setup_irq -> irq_desc->startup() + */ +static unsigned int startup_cobalt_irq(unsigned int irq) +{ + unsigned long flags; + + spin_lock_irqsave(&cobalt_lock, flags); + if ((irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS | IRQ_WAITING))) + irq_desc[irq].status &= ~(IRQ_DISABLED | IRQ_INPROGRESS | IRQ_WAITING); + enable_cobalt_irq(irq); + spin_unlock_irqrestore(&cobalt_lock, flags); + return 0; +} + +static void ack_cobalt_irq(unsigned int irq) +{ + unsigned long flags; + + spin_lock_irqsave(&cobalt_lock, flags); + disable_cobalt_irq(irq); + apic_write(APIC_EOI, APIC_EIO_ACK); + spin_unlock_irqrestore(&cobalt_lock, flags); +} + +static void end_cobalt_irq(unsigned int irq) +{ + unsigned long flags; + + spin_lock_irqsave(&cobalt_lock, flags); + if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS))) + enable_cobalt_irq(irq); + spin_unlock_irqrestore(&cobalt_lock, flags); +} + +static struct irq_chip cobalt_irq_type = { + .typename = "Cobalt-APIC", + .startup = startup_cobalt_irq, + .shutdown = disable_cobalt_irq, + .enable = enable_cobalt_irq, + .disable = disable_cobalt_irq, + .ack = ack_cobalt_irq, + .end = end_cobalt_irq, +}; + + +/* + * This is the PIIX4-based 8259 that is wired up indirectly to Cobalt + * -- not the manner expected by the code in i8259.c. + * + * there is a 'master' physical interrupt source that gets sent to + * the CPU. But in the chipset there are various 'virtual' interrupts + * waiting to be handled. We represent this to Linux through a 'master' + * interrupt controller type, and through a special virtual interrupt- + * controller. Device drivers only see the virtual interrupt sources. + */ +static unsigned int startup_piix4_master_irq(unsigned int irq) +{ + init_8259A(0); + + return startup_cobalt_irq(irq); +} + +static void end_piix4_master_irq(unsigned int irq) +{ + unsigned long flags; + + spin_lock_irqsave(&cobalt_lock, flags); + enable_cobalt_irq(irq); + spin_unlock_irqrestore(&cobalt_lock, flags); +} + +static struct irq_chip piix4_master_irq_type = { + .typename = "PIIX4-master", + .startup = startup_piix4_master_irq, + .ack = ack_cobalt_irq, + .end = end_piix4_master_irq, +}; + + +static struct irq_chip piix4_virtual_irq_type = { + .typename = "PIIX4-virtual", + .shutdown = disable_8259A_irq, + .enable = enable_8259A_irq, + .disable = disable_8259A_irq, +}; + + +/* + * PIIX4-8259 master/virtual functions to handle interrupt requests + * from legacy devices: floppy, parallel, serial, rtc. + * + * None of these get Cobalt APIC entries, neither do they have IDT + * entries. These interrupts are purely virtual and distributed from + * the 'master' interrupt source: CO_IRQ_8259. + * + * When the 8259 interrupts its handler figures out which of these + * devices is interrupting and dispatches to its handler. + * + * CAREFUL: devices see the 'virtual' interrupt only. Thus disable/ + * enable_irq gets the right irq. This 'master' irq is never directly + * manipulated by any driver. + */ +static irqreturn_t piix4_master_intr(int irq, void *dev_id) +{ + int realirq; + irq_desc_t *desc; + unsigned long flags; + + spin_lock_irqsave(&i8259A_lock, flags); + + /* Find out what's interrupting in the PIIX4 master 8259 */ + outb(0x0c, 0x20); /* OCW3 Poll command */ + realirq = inb(0x20); + + /* + * Bit 7 == 0 means invalid/spurious + */ + if (unlikely(!(realirq & 0x80))) + goto out_unlock; + + realirq &= 7; + + if (unlikely(realirq == 2)) { + outb(0x0c, 0xa0); + realirq = inb(0xa0); + + if (unlikely(!(realirq & 0x80))) + goto out_unlock; + + realirq = (realirq & 7) + 8; + } + + /* mask and ack interrupt */ + cached_irq_mask |= 1 << realirq; + if (unlikely(realirq > 7)) { + inb(0xa1); + outb(cached_slave_mask, 0xa1); + outb(0x60 + (realirq & 7), 0xa0); + outb(0x60 + 2, 0x20); + } else { + inb(0x21); + outb(cached_master_mask, 0x21); + outb(0x60 + realirq, 0x20); + } + + spin_unlock_irqrestore(&i8259A_lock, flags); + + desc = irq_desc + realirq; + + /* + * handle this 'virtual interrupt' as a Cobalt one now. + */ + kstat_cpu(smp_processor_id()).irqs[realirq]++; + + if (likely(desc->action != NULL)) + handle_IRQ_event(realirq, desc->action); + + if (!(desc->status & IRQ_DISABLED)) + enable_8259A_irq(realirq); + + return IRQ_HANDLED; + +out_unlock: + spin_unlock_irqrestore(&i8259A_lock, flags); + return IRQ_NONE; +} + +static struct irqaction master_action = { + .handler = piix4_master_intr, + .name = "PIIX4-8259", +}; + +static struct irqaction cascade_action = { + .handler = no_action, + .name = "cascade", +}; + + +void init_VISWS_APIC_irqs(void) +{ + int i; + + for (i = 0; i < CO_IRQ_APIC0 + CO_APIC_LAST + 1; i++) { + irq_desc[i].status = IRQ_DISABLED; + irq_desc[i].action = 0; + irq_desc[i].depth = 1; + + if (i == 0) { + irq_desc[i].chip = &cobalt_irq_type; + } + else if (i == CO_IRQ_IDE0) { + irq_desc[i].chip = &cobalt_irq_type; + } + else if (i == CO_IRQ_IDE1) { + irq_desc[i].chip = &cobalt_irq_type; + } + else if (i == CO_IRQ_8259) { + irq_desc[i].chip = &piix4_master_irq_type; + } + else if (i < CO_IRQ_APIC0) { + irq_desc[i].chip = &piix4_virtual_irq_type; + } + else if (IS_CO_APIC(i)) { + irq_desc[i].chip = &cobalt_irq_type; + } + } + + setup_irq(CO_IRQ_8259, &master_action); + setup_irq(2, &cascade_action); +} diff --git a/arch/x86/lguest/Kconfig b/arch/x86/lguest/Kconfig index 964dfa36d367..c70e12b1a637 100644 --- a/arch/x86/lguest/Kconfig +++ b/arch/x86/lguest/Kconfig @@ -3,7 +3,7 @@ config LGUEST_GUEST select PARAVIRT depends on X86_32 depends on !X86_PAE - depends on !(X86_VISWS || X86_VOYAGER) + depends on !X86_VOYAGER select VIRTIO select VIRTIO_RING select VIRTIO_CONSOLE diff --git a/arch/x86/mach-default/setup.c b/arch/x86/mach-default/setup.c index 2f5e277686b8..48278fa7d3de 100644 --- a/arch/x86/mach-default/setup.c +++ b/arch/x86/mach-default/setup.c @@ -10,6 +10,14 @@ #include <asm/e820.h> #include <asm/setup.h> +/* + * Any quirks to be performed to initialize timers/irqs/etc? + */ +int (*arch_time_init_quirk)(void); +int (*arch_pre_intr_init_quirk)(void); +int (*arch_intr_init_quirk)(void); +int (*arch_trap_init_quirk)(void); + #ifdef CONFIG_HOTPLUG_CPU #define DEFAULT_SEND_IPI (1) #else @@ -29,6 +37,10 @@ int no_broadcast=DEFAULT_SEND_IPI; **/ void __init pre_intr_init_hook(void) { + if (arch_pre_intr_init_quirk) { + if (arch_pre_intr_init_quirk()) + return; + } init_ISA_irqs(); } @@ -52,6 +64,10 @@ static struct irqaction irq2 = { **/ void __init intr_init_hook(void) { + if (arch_intr_init_quirk) { + if (arch_intr_init_quirk()) + return; + } #ifdef CONFIG_X86_LOCAL_APIC apic_intr_init(); #endif @@ -65,7 +81,7 @@ void __init intr_init_hook(void) * * Description: * generally used to activate any machine specific identification - * routines that may be needed before setup_arch() runs. On VISWS + * routines that may be needed before setup_arch() runs. On Voyager * this is used to get the board revision and type. **/ void __init pre_setup_arch_hook(void) @@ -81,6 +97,10 @@ void __init pre_setup_arch_hook(void) **/ void __init trap_init_hook(void) { + if (arch_trap_init_quirk) { + if (arch_trap_init_quirk()) + return; + } } static struct irqaction irq0 = { @@ -99,6 +119,16 @@ static struct irqaction irq0 = { **/ void __init time_init_hook(void) { + if (arch_time_init_quirk) { + /* + * A nonzero return code does not mean failure, it means + * that the architecture quirk does not want any + * generic (timer) setup to be performed after this: + */ + if (arch_time_init_quirk()) + return; + } + irq0.mask = cpumask_of_cpu(0); setup_irq(0, &irq0); } diff --git a/arch/x86/mach-visws/Makefile b/arch/x86/mach-visws/Makefile deleted file mode 100644 index 835fd96ad768..000000000000 --- a/arch/x86/mach-visws/Makefile +++ /dev/null @@ -1,8 +0,0 @@ -# -# Makefile for the linux kernel. -# - -obj-y := setup.o traps.o reboot.o - -obj-$(CONFIG_X86_VISWS_APIC) += visws_apic.o -obj-$(CONFIG_X86_LOCAL_APIC) += mpparse.o diff --git a/arch/x86/mach-visws/mpparse.c b/arch/x86/mach-visws/mpparse.c deleted file mode 100644 index a2fb78c0d154..000000000000 --- a/arch/x86/mach-visws/mpparse.c +++ /dev/null @@ -1,85 +0,0 @@ - -#include <linux/init.h> -#include <linux/smp.h> - -#include <asm/smp.h> -#include <asm/io.h> - -#include "cobalt.h" -#include "mach_apic.h" - -extern unsigned int __cpuinitdata maxcpus; - -/* - * The Visual Workstation is Intel MP compliant in the hardware - * sense, but it doesn't have a BIOS(-configuration table). - * No problem for Linux. - */ - -static void __init MP_processor_info (struct mpc_config_processor *m) -{ - int ver, logical_apicid; - physid_mask_t apic_cpus; - - if (!(m->mpc_cpuflag & CPU_ENABLED)) - return; - - logical_apicid = m->mpc_apicid; - printk(KERN_INFO "%sCPU #%d %u:%u APIC version %d\n", - m->mpc_cpuflag & CPU_BOOTPROCESSOR ? "Bootup " : "", - m->mpc_apicid, - (m->mpc_cpufeature & CPU_FAMILY_MASK) >> 8, - (m->mpc_cpufeature & CPU_MODEL_MASK) >> 4, - m->mpc_apicver); - - if (m->mpc_cpuflag & CPU_BOOTPROCESSOR) - boot_cpu_physical_apicid = m->mpc_apicid; - - ver = m->mpc_apicver; - if ((ver >= 0x14 && m->mpc_apicid >= 0xff) || m->mpc_apicid >= 0xf) { - printk(KERN_ERR "Processor #%d INVALID. (Max ID: %d).\n", - m->mpc_apicid, MAX_APICS); - return; - } - - apic_cpus = apicid_to_cpu_present(m->mpc_apicid); - physids_or(phys_cpu_present_map, phys_cpu_present_map, apic_cpus); - /* - * Validate version - */ - if (ver == 0x0) { - printk(KERN_ERR "BIOS bug, APIC version is 0 for CPU#%d! " - "fixing up to 0x10. (tell your hw vendor)\n", - m->mpc_apicid); - ver = 0x10; - } - apic_version[m->mpc_apicid] = ver; -} - -void __init find_smp_config(void) -{ - struct mpc_config_processor *mp = phys_to_virt(CO_CPU_TAB_PHYS); - unsigned short ncpus = readw(phys_to_virt(CO_CPU_NUM_PHYS)); - - if (ncpus > CO_CPU_MAX) { - printk(KERN_WARNING "find_visws_smp: got cpu count of %d at %p\n", - ncpus, mp); - - ncpus = CO_CPU_MAX; - } - - if (ncpus > maxcpus) - ncpus = maxcpus; - -#ifdef CONFIG_X86_LOCAL_APIC - smp_found_config = 1; -#endif - while (ncpus--) - MP_processor_info(mp++); - - mp_lapic_addr = APIC_DEFAULT_PHYS_BASE; -} - -void __init get_smp_config (void) -{ -} diff --git a/arch/x86/mach-visws/reboot.c b/arch/x86/mach-visws/reboot.c deleted file mode 100644 index 99332abfad42..000000000000 --- a/arch/x86/mach-visws/reboot.c +++ /dev/null @@ -1,55 +0,0 @@ -#include <linux/module.h> -#include <linux/smp.h> -#include <linux/delay.h> - -#include <asm/io.h> -#include "piix4.h" - -void (*pm_power_off)(void); -EXPORT_SYMBOL(pm_power_off); - -void machine_shutdown(void) -{ -#ifdef CONFIG_SMP - smp_send_stop(); -#endif -} - -void machine_emergency_restart(void) -{ - /* - * Visual Workstations restart after this - * register is poked on the PIIX4 - */ - outb(PIIX4_RESET_VAL, PIIX4_RESET_PORT); -} - -void machine_restart(char * __unused) -{ - machine_shutdown(); - machine_emergency_restart(); -} - -void machine_power_off(void) -{ - unsigned short pm_status; - extern unsigned int pci_bus0; - - while ((pm_status = inw(PMSTS_PORT)) & 0x100) - outw(pm_status, PMSTS_PORT); - - outw(PM_SUSPEND_ENABLE, PMCNTRL_PORT); - - mdelay(10); - -#define PCI_CONF1_ADDRESS(bus, devfn, reg) \ - (0x80000000 | (bus << 16) | (devfn << 8) | (reg & ~3)) - - outl(PCI_CONF1_ADDRESS(pci_bus0, SPECIAL_DEV, SPECIAL_REG), 0xCF8); - outl(PIIX_SPECIAL_STOP, 0xCFC); -} - -void machine_halt(void) -{ -} - diff --git a/arch/x86/mach-visws/setup.c b/arch/x86/mach-visws/setup.c deleted file mode 100644 index d67868ec9b7f..000000000000 --- a/arch/x86/mach-visws/setup.c +++ /dev/null @@ -1,183 +0,0 @@ -/* - * Unmaintained SGI Visual Workstation support. - * Split out from setup.c by davej@suse.de - */ - -#include <linux/smp.h> -#include <linux/init.h> -#include <linux/interrupt.h> -#include <linux/module.h> - -#include <asm/fixmap.h> -#include <asm/arch_hooks.h> -#include <asm/io.h> -#include <asm/e820.h> -#include <asm/setup.h> -#include "cobalt.h" -#include "piix4.h" - -int no_broadcast; - -char visws_board_type = -1; -char visws_board_rev = -1; - -void __init visws_get_board_type_and_rev(void) -{ - int raw; - - visws_board_type = (char)(inb_p(PIIX_GPI_BD_REG) & PIIX_GPI_BD_REG) - >> PIIX_GPI_BD_SHIFT; - /* - * Get Board rev. - * First, we have to initialize the 307 part to allow us access - * to the GPIO registers. Let's map them at 0x0fc0 which is right - * after the PIIX4 PM section. - */ - outb_p(SIO_DEV_SEL, SIO_INDEX); - outb_p(SIO_GP_DEV, SIO_DATA); /* Talk to GPIO regs. */ - - outb_p(SIO_DEV_MSB, SIO_INDEX); - outb_p(SIO_GP_MSB, SIO_DATA); /* MSB of GPIO base address */ - - outb_p(SIO_DEV_LSB, SIO_INDEX); - outb_p(SIO_GP_LSB, SIO_DATA); /* LSB of GPIO base address */ - - outb_p(SIO_DEV_ENB, SIO_INDEX); - outb_p(1, SIO_DATA); /* Enable GPIO registers. */ - - /* - * Now, we have to map the power management section to write - * a bit which enables access to the GPIO registers. - * What lunatic came up with this shit? - */ - outb_p(SIO_DEV_SEL, SIO_INDEX); - outb_p(SIO_PM_DEV, SIO_DATA); /* Talk to GPIO regs. */ - - outb_p(SIO_DEV_MSB, SIO_INDEX); - outb_p(SIO_PM_MSB, SIO_DATA); /* MSB of PM base address */ - - outb_p(SIO_DEV_LSB, SIO_INDEX); - outb_p(SIO_PM_LSB, SIO_DATA); /* LSB of PM base address */ - - outb_p(SIO_DEV_ENB, SIO_INDEX); - outb_p(1, SIO_DATA); /* Enable PM registers. */ - - /* - * Now, write the PM register which enables the GPIO registers. - */ - outb_p(SIO_PM_FER2, SIO_PM_INDEX); - outb_p(SIO_PM_GP_EN, SIO_PM_DATA); - - /* - * Now, initialize the GPIO registers. - * We want them all to be inputs which is the - * power on default, so let's leave them alone. - * So, let's just read the board rev! - */ - raw = inb_p(SIO_GP_DATA1); - raw &= 0x7f; /* 7 bits of valid board revision ID. */ - - if (visws_board_type == VISWS_320) { - if (raw < 0x6) { - visws_board_rev = 4; - } else if (raw < 0xc) { - visws_board_rev = 5; - } else { - visws_board_rev = 6; - } - } else if (visws_board_type == VISWS_540) { - visws_board_rev = 2; - } else { - visws_board_rev = raw; - } - - printk(KERN_INFO "Silicon Graphics Visual Workstation %s (rev %d) detected\n", - (visws_board_type == VISWS_320 ? "320" : - (visws_board_type == VISWS_540 ? "540" : - "unknown")), visws_board_rev); -} - -void __init pre_intr_init_hook(void) -{ - init_VISWS_APIC_irqs(); -} - -void __init intr_init_hook(void) -{ -#ifdef CONFIG_X86_LOCAL_APIC - apic_intr_init(); -#endif -} - -void __init pre_setup_arch_hook() -{ - visws_get_board_type_and_rev(); -} - -static struct irqaction irq0 = { - .handler = timer_interrupt, - .flags = IRQF_DISABLED | IRQF_IRQPOLL, - .name = "timer", -}; - -void __init time_init_hook(void) -{ - printk(KERN_INFO "Starting Cobalt Timer system clock\n"); - - /* Set the countdown value */ - co_cpu_write(CO_CPU_TIMEVAL, CO_TIME_HZ/HZ); - - /* Start the timer */ - co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) | CO_CTRL_TIMERUN); - - /* Enable (unmask) the timer interrupt */ - co_cpu_write(CO_CPU_CTRL, co_cpu_read(CO_CPU_CTRL) & ~CO_CTRL_TIMEMASK); - - /* Wire cpu IDT entry to s/w handler (and Cobalt APIC to IDT) */ - setup_irq(0, &irq0); -} - -/* Hook for machine specific memory setup. */ - -#define MB (1024 * 1024) - -unsigned long sgivwfb_mem_phys; -unsigned long sgivwfb_mem_size; -EXPORT_SYMBOL(sgivwfb_mem_phys); -EXPORT_SYMBOL(sgivwfb_mem_size); - -long long mem_size __initdata = 0; - -char * __init machine_specific_memory_setup(void) -{ - long long gfx_mem_size = 8 * MB; - - mem_size = boot_params.alt_mem_k; - - if (!mem_size) { - printk(KERN_WARNING "Bootloader didn't set memory size, upgrade it !\n"); - mem_size = 128 * MB; - } - - /* - * this hardcodes the graphics memory to 8 MB - * it really should be sized dynamically (or at least - * set as a boot param) - */ - if (!sgivwfb_mem_size) { - printk(KERN_WARNING "Defaulting to 8 MB framebuffer size\n"); - sgivwfb_mem_size = 8 * MB; - } - - /* - * Trim to nearest MB - */ - sgivwfb_mem_size &= ~((1 << 20) - 1); - sgivwfb_mem_phys = mem_size - gfx_mem_size; - - e820_add_region(0, LOWMEMSIZE(), E820_RAM); - e820_add_region(HIGH_MEMORY, mem_size - sgivwfb_mem_size - HIGH_MEMORY, E820_RAM); - e820_add_region(sgivwfb_mem_phys, sgivwfb_mem_size, E820_RESERVED); - - return "PROM"; -} diff --git a/arch/x86/mach-visws/traps.c b/arch/x86/mach-visws/traps.c deleted file mode 100644 index bfac6ba10f8a..000000000000 --- a/arch/x86/mach-visws/traps.c +++ /dev/null @@ -1,69 +0,0 @@ -/* VISWS traps */ - -#include <linux/sched.h> -#include <linux/kernel.h> -#include <linux/init.h> -#include <linux/pci.h> -#include <linux/pci_ids.h> - -#include <asm/io.h> -#include <asm/arch_hooks.h> -#include <asm/apic.h> -#include "cobalt.h" -#include "lithium.h" - - -#define A01234 (LI_INTA_0 | LI_INTA_1 | LI_INTA_2 | LI_INTA_3 | LI_INTA_4) -#define BCD (LI_INTB | LI_INTC | LI_INTD) -#define ALLDEVS (A01234 | BCD) - -static __init void lithium_init(void) -{ - set_fixmap(FIX_LI_PCIA, LI_PCI_A_PHYS); - set_fixmap(FIX_LI_PCIB, LI_PCI_B_PHYS); - - if ((li_pcia_read16(PCI_VENDOR_ID) != PCI_VENDOR_ID_SGI) || - (li_pcia_read16(PCI_DEVICE_ID) != PCI_DEVICE_ID_SGI_LITHIUM)) { - printk(KERN_EMERG "Lithium hostbridge %c not found\n", 'A'); - panic("This machine is not SGI Visual Workstation 320/540"); - } - - if ((li_pcib_read16(PCI_VENDOR_ID) != PCI_VENDOR_ID_SGI) || - (li_pcib_read16(PCI_DEVICE_ID) != PCI_DEVICE_ID_SGI_LITHIUM)) { - printk(KERN_EMERG "Lithium hostbridge %c not found\n", 'B'); - panic("This machine is not SGI Visual Workstation 320/540"); - } - - li_pcia_write16(LI_PCI_INTEN, ALLDEVS); - li_pcib_write16(LI_PCI_INTEN, ALLDEVS); -} - -static __init void cobalt_init(void) -{ - /* - * On normal SMP PC this is used only with SMP, but we have to - * use it and set it up here to start the Cobalt clock - */ - set_fixmap(FIX_APIC_BASE, APIC_DEFAULT_PHYS_BASE); - setup_local_APIC(); - printk(KERN_INFO "Local APIC Version %#x, ID %#x\n", - (unsigned int)apic_read(APIC_LVR), - (unsigned int)apic_read(APIC_ID)); - - set_fixmap(FIX_CO_CPU, CO_CPU_PHYS); - set_fixmap(FIX_CO_APIC, CO_APIC_PHYS); - printk(KERN_INFO "Cobalt Revision %#lx, APIC ID %#lx\n", - co_cpu_read(CO_CPU_REV), co_apic_read(CO_APIC_ID)); - - /* Enable Cobalt APIC being careful to NOT change the ID! */ - co_apic_write(CO_APIC_ID, co_apic_read(CO_APIC_ID) | CO_APIC_ENABLE); - - printk(KERN_INFO "Cobalt APIC enabled: ID reg %#lx\n", - co_apic_read(CO_APIC_ID)); -} - -void __init trap_init_hook(void) -{ - lithium_init(); - cobalt_init(); -} diff --git a/arch/x86/mach-visws/visws_apic.c b/arch/x86/mach-visws/visws_apic.c deleted file mode 100644 index d8b2cfd85d92..000000000000 --- a/arch/x86/mach-visws/visws_apic.c +++ /dev/null @@ -1,296 +0,0 @@ -/* - * Copyright (C) 1999 Bent Hagemark, Ingo Molnar - * - * SGI Visual Workstation interrupt controller - * - * The Cobalt system ASIC in the Visual Workstation contains a "Cobalt" APIC - * which serves as the main interrupt controller in the system. Non-legacy - * hardware in the system uses this controller directly. Legacy devices - * are connected to the PIIX4 which in turn has its 8259(s) connected to - * a of the Cobalt APIC entry. - * - * 09/02/2000 - Updated for 2.4 by jbarnes@sgi.com - * - * 25/11/2002 - Updated for 2.5 by Andrey Panin <pazke@orbita1.ru> - */ - -#include <linux/kernel_stat.h> -#include <linux/interrupt.h> -#include <linux/init.h> - -#include <asm/io.h> -#include <asm/apic.h> -#include <asm/i8259.h> -#include <asm/irq_vectors.h> - -#include "cobalt.h" - -static DEFINE_SPINLOCK(cobalt_lock); - -/* - * Set the given Cobalt APIC Redirection Table entry to point - * to the given IDT vector/index. - */ -static inline void co_apic_set(int entry, int irq) -{ - co_apic_write(CO_APIC_LO(entry), CO_APIC_LEVEL | (irq + FIRST_EXTERNAL_VECTOR)); - co_apic_write(CO_APIC_HI(entry), 0); -} - -/* - * Cobalt (IO)-APIC functions to handle PCI devices. - */ -static inline int co_apic_ide0_hack(void) -{ - extern char visws_board_type; - extern char visws_board_rev; - - if (visws_board_type == VISWS_320 && visws_board_rev == 5) - return 5; - return CO_APIC_IDE0; -} - -static int is_co_apic(unsigned int irq) -{ - if (IS_CO_APIC(irq)) - return CO_APIC(irq); - - switch (irq) { - case 0: return CO_APIC_CPU; - case CO_IRQ_IDE0: return co_apic_ide0_hack(); - case CO_IRQ_IDE1: return CO_APIC_IDE1; - default: return -1; - } -} - - -/* - * This is the SGI Cobalt (IO-)APIC: - */ - -static void enable_cobalt_irq(unsigned int irq) -{ - co_apic_set(is_co_apic(irq), irq); -} - -static void disable_cobalt_irq(unsigned int irq) -{ - int entry = is_co_apic(irq); - - co_apic_write(CO_APIC_LO(entry), CO_APIC_MASK); - co_apic_read(CO_APIC_LO(entry)); -} - -/* - * "irq" really just serves to identify the device. Here is where we - * map this to the Cobalt APIC entry where it's physically wired. - * This is called via request_irq -> setup_irq -> irq_desc->startup() - */ -static unsigned int startup_cobalt_irq(unsigned int irq) -{ - unsigned long flags; - - spin_lock_irqsave(&cobalt_lock, flags); - if ((irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS | IRQ_WAITING))) - irq_desc[irq].status &= ~(IRQ_DISABLED | IRQ_INPROGRESS | IRQ_WAITING); - enable_cobalt_irq(irq); - spin_unlock_irqrestore(&cobalt_lock, flags); - return 0; -} - -static void ack_cobalt_irq(unsigned int irq) -{ - unsigned long flags; - - spin_lock_irqsave(&cobalt_lock, flags); - disable_cobalt_irq(irq); - apic_write(APIC_EOI, APIC_EIO_ACK); - spin_unlock_irqrestore(&cobalt_lock, flags); -} - -static void end_cobalt_irq(unsigned int irq) -{ - unsigned long flags; - - spin_lock_irqsave(&cobalt_lock, flags); - if (!(irq_desc[irq].status & (IRQ_DISABLED | IRQ_INPROGRESS))) - enable_cobalt_irq(irq); - spin_unlock_irqrestore(&cobalt_lock, flags); -} - -static struct irq_chip cobalt_irq_type = { - .typename = "Cobalt-APIC", - .startup = startup_cobalt_irq, - .shutdown = disable_cobalt_irq, - .enable = enable_cobalt_irq, - .disable = disable_cobalt_irq, - .ack = ack_cobalt_irq, - .end = end_cobalt_irq, -}; - - -/* - * This is the PIIX4-based 8259 that is wired up indirectly to Cobalt - * -- not the manner expected by the code in i8259.c. - * - * there is a 'master' physical interrupt source that gets sent to - * the CPU. But in the chipset there are various 'virtual' interrupts - * waiting to be handled. We represent this to Linux through a 'master' - * interrupt controller type, and through a special virtual interrupt- - * controller. Device drivers only see the virtual interrupt sources. - */ -static unsigned int startup_piix4_master_irq(unsigned int irq) -{ - init_8259A(0); - - return startup_cobalt_irq(irq); -} - -static void end_piix4_master_irq(unsigned int irq) -{ - unsigned long flags; - - spin_lock_irqsave(&cobalt_lock, flags); - enable_cobalt_irq(irq); - spin_unlock_irqrestore(&cobalt_lock, flags); -} - -static struct irq_chip piix4_master_irq_type = { - .typename = "PIIX4-master", - .startup = startup_piix4_master_irq, - .ack = ack_cobalt_irq, - .end = end_piix4_master_irq, -}; - - -static struct irq_chip piix4_virtual_irq_type = { - .typename = "PIIX4-virtual", - .shutdown = disable_8259A_irq, - .enable = enable_8259A_irq, - .disable = disable_8259A_irq, -}; - - -/* - * PIIX4-8259 master/virtual functions to handle interrupt requests - * from legacy devices: floppy, parallel, serial, rtc. - * - * None of these get Cobalt APIC entries, neither do they have IDT - * entries. These interrupts are purely virtual and distributed from - * the 'master' interrupt source: CO_IRQ_8259. - * - * When the 8259 interrupts its handler figures out which of these - * devices is interrupting and dispatches to its handler. - * - * CAREFUL: devices see the 'virtual' interrupt only. Thus disable/ - * enable_irq gets the right irq. This 'master' irq is never directly - * manipulated by any driver. - */ -static irqreturn_t piix4_master_intr(int irq, void *dev_id) -{ - int realirq; - irq_desc_t *desc; - unsigned long flags; - - spin_lock_irqsave(&i8259A_lock, flags); - - /* Find out what's interrupting in the PIIX4 master 8259 */ - outb(0x0c, 0x20); /* OCW3 Poll command */ - realirq = inb(0x20); - - /* - * Bit 7 == 0 means invalid/spurious - */ - if (unlikely(!(realirq & 0x80))) - goto out_unlock; - - realirq &= 7; - - if (unlikely(realirq == 2)) { - outb(0x0c, 0xa0); - realirq = inb(0xa0); - - if (unlikely(!(realirq & 0x80))) - goto out_unlock; - - realirq = (realirq & 7) + 8; - } - - /* mask and ack interrupt */ - cached_irq_mask |= 1 << realirq; - if (unlikely(realirq > 7)) { - inb(0xa1); - outb(cached_slave_mask, 0xa1); - outb(0x60 + (realirq & 7), 0xa0); - outb(0x60 + 2, 0x20); - } else { - inb(0x21); - outb(cached_master_mask, 0x21); - outb(0x60 + realirq, 0x20); - } - - spin_unlock_irqrestore(&i8259A_lock, flags); - - desc = irq_desc + realirq; - - /* - * handle this 'virtual interrupt' as a Cobalt one now. - */ - kstat_cpu(smp_processor_id()).irqs[realirq]++; - - if (likely(desc->action != NULL)) - handle_IRQ_event(realirq, desc->action); - - if (!(desc->status & IRQ_DISABLED)) - enable_8259A_irq(realirq); - - return IRQ_HANDLED; - -out_unlock: - spin_unlock_irqrestore(&i8259A_lock, flags); - return IRQ_NONE; -} - -static struct irqaction master_action = { - .handler = piix4_master_intr, - .name = "PIIX4-8259", -}; - -static struct irqaction cascade_action = { - .handler = no_action, - .name = "cascade", -}; - - -void init_VISWS_APIC_irqs(void) -{ - int i; - - for (i = 0; i < CO_IRQ_APIC0 + CO_APIC_LAST + 1; i++) { - irq_desc[i].status = IRQ_DISABLED; - irq_desc[i].action = 0; - irq_desc[i].depth = 1; - - if (i == 0) { - irq_desc[i].chip = &cobalt_irq_type; - } - else if (i == CO_IRQ_IDE0) { - irq_desc[i].chip = &cobalt_irq_type; - } - else if (i == CO_IRQ_IDE1) { - irq_desc[i].chip = &cobalt_irq_type; - } - else if (i == CO_IRQ_8259) { - irq_desc[i].chip = &piix4_master_irq_type; - } - else if (i < CO_IRQ_APIC0) { - irq_desc[i].chip = &piix4_virtual_irq_type; - } - else if (IS_CO_APIC(i)) { - irq_desc[i].chip = &cobalt_irq_type; - } - } - - setup_irq(CO_IRQ_8259, &master_action); - setup_irq(2, &cascade_action); -} diff --git a/arch/x86/pci/Makefile b/arch/x86/pci/Makefile index 99d9f095e4d4..e515e8db842a 100644 --- a/arch/x86/pci/Makefile +++ b/arch/x86/pci/Makefile @@ -9,9 +9,7 @@ pci-y := fixup.o pci-$(CONFIG_ACPI) += acpi.o pci-y += legacy.o irq.o -# Careful: VISWS overrule the pci-y above. The colons are -# therefor correct. This needs a proper fix by distangling the code. -pci-$(CONFIG_X86_VISWS) := visws.o fixup.o +pci-$(CONFIG_X86_VISWS) += visws.o pci-$(CONFIG_X86_NUMAQ) += numa.o diff --git a/arch/x86/pci/legacy.c b/arch/x86/pci/legacy.c index 3c1d795cbbe9..132876cc6fca 100644 --- a/arch/x86/pci/legacy.c +++ b/arch/x86/pci/legacy.c @@ -62,6 +62,11 @@ int __init pci_subsys_init(void) #endif pci_legacy_init(); pcibios_irq_init(); +#ifdef CONFIG_X86_NUMAQ + pci_numa_init(); +#endif pcibios_init(); + + return 0; } subsys_initcall(pci_subsys_init); diff --git a/arch/x86/pci/numa.c b/arch/x86/pci/numa.c index e1620dc8649a..8b5ca1966731 100644 --- a/arch/x86/pci/numa.c +++ b/arch/x86/pci/numa.c @@ -151,7 +151,7 @@ static void __devinit pci_fixup_i450nx(struct pci_dev *d) } DECLARE_PCI_FIXUP_HEADER(PCI_VENDOR_ID_INTEL, PCI_DEVICE_ID_INTEL_82451NX, pci_fixup_i450nx); -static int __init pci_numa_init(void) +int __init pci_numa_init(void) { int quad; @@ -176,11 +176,3 @@ static int __init pci_numa_init(void) } return 0; } - -static __init int pci_subsys_init(void) -{ - pci_numa_init(); - pcibios_irq_init(); - pcibios_init(); -} -subsys_initcall(pci_subsys_init); diff --git a/arch/x86/pci/pci.h b/arch/x86/pci/pci.h index 58241748470f..b2270a55b0cf 100644 --- a/arch/x86/pci/pci.h +++ b/arch/x86/pci/pci.h @@ -107,6 +107,7 @@ extern void __init dmi_check_skip_isa_align(void); /* some common used subsys_initcalls */ extern int __init pci_acpi_init(void); extern int __init pcibios_irq_init(void); +extern int __init pci_numa_init(void); extern int __init pcibios_init(void); /* pci-mmconfig.c */ diff --git a/arch/x86/pci/visws.c b/arch/x86/pci/visws.c index 16e52063ecb3..1a7bed492bb1 100644 --- a/arch/x86/pci/visws.c +++ b/arch/x86/pci/visws.c @@ -8,18 +8,19 @@ #include <linux/pci.h> #include <linux/init.h> -#include "cobalt.h" -#include "lithium.h" +#include <asm/setup.h> +#include <asm/visws/cobalt.h> +#include <asm/visws/lithium.h> #include "pci.h" static int pci_visws_enable_irq(struct pci_dev *dev) { return 0; } static void pci_visws_disable_irq(struct pci_dev *dev) { } -int (*pcibios_enable_irq)(struct pci_dev *dev) = &pci_visws_enable_irq; -void (*pcibios_disable_irq)(struct pci_dev *dev) = &pci_visws_disable_irq; +/* int (*pcibios_enable_irq)(struct pci_dev *dev) = &pci_visws_enable_irq; */ +/* void (*pcibios_disable_irq)(struct pci_dev *dev) = &pci_visws_disable_irq; */ -void __init pcibios_penalize_isa_irq(int irq, int active) {} +/* void __init pcibios_penalize_isa_irq(int irq, int active) {} */ unsigned int pci_bus0, pci_bus1; @@ -107,7 +108,15 @@ static int __init pci_visws_init(void) static __init int pci_subsys_init(void) { + if (!is_visws_box()) + return -1; + + pcibios_enable_irq = &pci_visws_enable_irq; + pcibios_disable_irq = &pci_visws_disable_irq; + pci_visws_init(); pcibios_init(); + + return 0; } subsys_initcall(pci_subsys_init); |