diff options
Diffstat (limited to 'arch/avr32/boards/atngw100/setup.c')
| -rw-r--r-- | arch/avr32/boards/atngw100/setup.c | 124 |
1 files changed, 124 insertions, 0 deletions
diff --git a/arch/avr32/boards/atngw100/setup.c b/arch/avr32/boards/atngw100/setup.c new file mode 100644 index 000000000000..9bc37d4f6687 --- /dev/null +++ b/arch/avr32/boards/atngw100/setup.c @@ -0,0 +1,124 @@ +/* + * Board-specific setup code for the ATNGW100 Network Gateway + * + * Copyright (C) 2005-2006 Atmel Corporation + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ +#include <linux/clk.h> +#include <linux/etherdevice.h> +#include <linux/init.h> +#include <linux/linkage.h> +#include <linux/platform_device.h> +#include <linux/types.h> +#include <linux/spi/spi.h> + +#include <asm/io.h> +#include <asm/setup.h> + +#include <asm/arch/at32ap7000.h> +#include <asm/arch/board.h> +#include <asm/arch/init.h> + +/* Initialized by bootloader-specific startup code. */ +struct tag *bootloader_tags __initdata; + +struct eth_addr { + u8 addr[6]; +}; +static struct eth_addr __initdata hw_addr[2]; +static struct eth_platform_data __initdata eth_data[2]; + +static struct spi_board_info spi0_board_info[] __initdata = { + { + .modalias = "mtd_dataflash", + .max_speed_hz = 10000000, + .chip_select = 0, + }, +}; + +/* + * The next two functions should go away as the boot loader is + * supposed to initialize the macb address registers with a valid + * ethernet address. But we need to keep it around for a while until + * we can be reasonably sure the boot loader does this. + * + * The phy_id is ignored as the driver will probe for it. + */ +static int __init parse_tag_ethernet(struct tag *tag) +{ + int i; + + i = tag->u.ethernet.mac_index; + if (i < ARRAY_SIZE(hw_addr)) + memcpy(hw_addr[i].addr, tag->u.ethernet.hw_address, + sizeof(hw_addr[i].addr)); + + return 0; +} +__tagtable(ATAG_ETHERNET, parse_tag_ethernet); + +static void __init set_hw_addr(struct platform_device *pdev) +{ + struct resource *res = platform_get_resource(pdev, IORESOURCE_MEM, 0); + const u8 *addr; + void __iomem *regs; + struct clk *pclk; + + if (!res) + return; + if (pdev->id >= ARRAY_SIZE(hw_addr)) + return; + + addr = hw_addr[pdev->id].addr; + if (!is_valid_ether_addr(addr)) + return; + + /* + * Since this is board-specific code, we'll cheat and use the + * physical address directly as we happen to know that it's + * the same as the virtual address. + */ + regs = (void __iomem __force *)res->start; + pclk = clk_get(&pdev->dev, "pclk"); + if (!pclk) + return; + + clk_enable(pclk); + __raw_writel((addr[3] << 24) | (addr[2] << 16) + | (addr[1] << 8) | addr[0], regs + 0x98); + __raw_writel((addr[5] << 8) | addr[4], regs + 0x9c); + clk_disable(pclk); + clk_put(pclk); +} + +struct platform_device *at32_usart_map[1]; +unsigned int at32_nr_usarts = 1; + +void __init setup_board(void) +{ + at32_map_usart(1, 0); /* USART 1: /dev/ttyS0, DB9 */ + at32_setup_serial_console(0); +} + +static int __init atngw100_init(void) +{ + /* + * ATNGW100 uses 16-bit SDRAM interface, so we don't need to + * reserve any pins for it. + */ + + at32_add_system_devices(); + + at32_add_device_usart(0); + + set_hw_addr(at32_add_device_eth(0, ð_data[0])); + set_hw_addr(at32_add_device_eth(1, ð_data[1])); + + at32_add_device_spi(0, spi0_board_info, ARRAY_SIZE(spi0_board_info)); + + return 0; +} +postcore_initcall(atngw100_init); |