diff options
Diffstat (limited to 'arch/arm')
39 files changed, 730 insertions, 118 deletions
diff --git a/arch/arm/boot/dts/at91sam9g20.dtsi b/arch/arm/boot/dts/at91sam9g20.dtsi index a100db03ec90..f091d679bd4c 100644 --- a/arch/arm/boot/dts/at91sam9g20.dtsi +++ b/arch/arm/boot/dts/at91sam9g20.dtsi @@ -59,6 +59,26 @@ reg = <0xfffff000 0x200>; }; + ramc0: ramc@ffffea00 { + compatible = "atmel,at91sam9260-sdramc"; + reg = <0xffffea00 0x200>; + }; + + pmc: pmc@fffffc00 { + compatible = "atmel,at91rm9200-pmc"; + reg = <0xfffffc00 0x100>; + }; + + rstc@fffffd00 { + compatible = "atmel,at91sam9260-rstc"; + reg = <0xfffffd00 0x10>; + }; + + shdwc@fffffd10 { + compatible = "atmel,at91sam9260-shdwc"; + reg = <0xfffffd10 0x10>; + }; + pit: timer@fffffd30 { compatible = "atmel,at91sam9260-pit"; reg = <0xfffffd30 0xf>; @@ -172,5 +192,41 @@ status = "disabled"; }; }; + + nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000 + 0xffffe800 0x200 + >; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + gpios = <&pioC 13 0 + &pioC 14 0 + 0 + >; + status = "disabled"; + }; + + usb0: ohci@00500000 { + compatible = "atmel,at91rm9200-ohci", "usb-ohci"; + reg = <0x00500000 0x100000>; + interrupts = <20 4>; + status = "disabled"; + }; + }; + + i2c@0 { + compatible = "i2c-gpio"; + gpios = <&pioA 23 0 /* sda */ + &pioA 24 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/at91sam9g25ek.dts b/arch/arm/boot/dts/at91sam9g25ek.dts index e64eb932083b..ac0dc0031dda 100644 --- a/arch/arm/boot/dts/at91sam9g25ek.dts +++ b/arch/arm/boot/dts/at91sam9g25ek.dts @@ -15,7 +15,7 @@ compatible = "atmel,at91sam9g25ek", "atmel,at91sam9x5ek", "atmel,at91sam9x5", "atmel,at91sam9"; chosen { - bootargs = "128M console=ttyS0,115200 mtdparts=atmel_nand:8M(bootstrap/uboot/kernel)ro,-(rootfs) root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs"; + bootargs = "128M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=ubifs ubi.mtd=1 root=ubi0:rootfs"; }; ahb { @@ -33,5 +33,17 @@ status = "okay"; }; }; + + usb0: ohci@00600000 { + status = "okay"; + num-ports = <2>; + atmel,vbus-gpio = <&pioD 19 0 + &pioD 20 0 + >; + }; + + usb1: ehci@00700000 { + status = "okay"; + }; }; }; diff --git a/arch/arm/boot/dts/at91sam9g45.dtsi b/arch/arm/boot/dts/at91sam9g45.dtsi index f779667159b1..3d0c32fb218f 100644 --- a/arch/arm/boot/dts/at91sam9g45.dtsi +++ b/arch/arm/boot/dts/at91sam9g45.dtsi @@ -60,6 +60,22 @@ reg = <0xfffff000 0x200>; }; + ramc0: ramc@ffffe400 { + compatible = "atmel,at91sam9g45-ddramc"; + reg = <0xffffe400 0x200 + 0xffffe600 0x200>; + }; + + pmc: pmc@fffffc00 { + compatible = "atmel,at91rm9200-pmc"; + reg = <0xfffffc00 0x100>; + }; + + rstc@fffffd00 { + compatible = "atmel,at91sam9g45-rstc"; + reg = <0xfffffd00 0x10>; + }; + pit: timer@fffffd30 { compatible = "atmel,at91sam9260-pit"; reg = <0xfffffd30 0xf>; @@ -67,6 +83,11 @@ }; + shdwc@fffffd10 { + compatible = "atmel,at91sam9rl-shdwc"; + reg = <0xfffffd10 0x10>; + }; + tcb0: timer@fff7c000 { compatible = "atmel,at91rm9200-tcb"; reg = <0xfff7c000 0x100>; @@ -180,5 +201,48 @@ status = "disabled"; }; }; + + nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000 + 0xffffe200 0x200 + >; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + gpios = <&pioC 8 0 + &pioC 14 0 + 0 + >; + status = "disabled"; + }; + + usb0: ohci@00700000 { + compatible = "atmel,at91rm9200-ohci", "usb-ohci"; + reg = <0x00700000 0x100000>; + interrupts = <22 4>; + status = "disabled"; + }; + + usb1: ehci@00800000 { + compatible = "atmel,at91sam9g45-ehci", "usb-ehci"; + reg = <0x00800000 0x100000>; + interrupts = <22 4>; + status = "disabled"; + }; + }; + + i2c@0 { + compatible = "i2c-gpio"; + gpios = <&pioA 20 0 /* sda */ + &pioA 21 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <5>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/at91sam9m10g45ek.dts b/arch/arm/boot/dts/at91sam9m10g45ek.dts index 15e25f903cad..c4c8ae4123d5 100644 --- a/arch/arm/boot/dts/at91sam9m10g45ek.dts +++ b/arch/arm/boot/dts/at91sam9m10g45ek.dts @@ -14,13 +14,24 @@ compatible = "atmel,at91sam9m10g45ek", "atmel,at91sam9g45", "atmel,at91sam9"; chosen { - bootargs = "mem=64M console=ttyS0,115200 mtdparts=atmel_nand:4M(bootstrap/uboot/kernel)ro,60M(rootfs),-(data) root=/dev/mtdblock1 rw rootfstype=jffs2"; + bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock1 rw rootfstype=jffs2"; }; memory@70000000 { reg = <0x70000000 0x4000000>; }; + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + }; + ahb { apb { dbgu: serial@ffffee00 { @@ -36,6 +47,39 @@ status = "okay"; }; }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + boot@0 { + label = "bootstrap/uboot/kernel"; + reg = <0x0 0x400000>; + }; + + rootfs@400000 { + label = "rootfs"; + reg = <0x400000 0x3C00000>; + }; + + data@4000000 { + label = "data"; + reg = <0x4000000 0xC000000>; + }; + }; + + usb0: ohci@00700000 { + status = "okay"; + num-ports = <2>; + atmel,vbus-gpio = <&pioD 1 0 + &pioD 3 0>; + }; + + usb1: ehci@00800000 { + status = "okay"; + }; }; leds { diff --git a/arch/arm/boot/dts/at91sam9x5.dtsi b/arch/arm/boot/dts/at91sam9x5.dtsi index a02e636d8a57..c111001f254e 100644 --- a/arch/arm/boot/dts/at91sam9x5.dtsi +++ b/arch/arm/boot/dts/at91sam9x5.dtsi @@ -58,6 +58,26 @@ reg = <0xfffff000 0x200>; }; + ramc0: ramc@ffffe800 { + compatible = "atmel,at91sam9g45-ddramc"; + reg = <0xffffe800 0x200>; + }; + + pmc: pmc@fffffc00 { + compatible = "atmel,at91rm9200-pmc"; + reg = <0xfffffc00 0x100>; + }; + + rstc@fffffe00 { + compatible = "atmel,at91sam9g45-rstc"; + reg = <0xfffffe00 0x10>; + }; + + shdwc@fffffe10 { + compatible = "atmel,at91sam9x5-shdwc"; + reg = <0xfffffe10 0x10>; + }; + pit: timer@fffffe30 { compatible = "atmel,at91sam9260-pit"; reg = <0xfffffe30 0xf>; @@ -172,5 +192,73 @@ status = "disabled"; }; }; + + nand0: nand@40000000 { + compatible = "atmel,at91rm9200-nand"; + #address-cells = <1>; + #size-cells = <1>; + reg = <0x40000000 0x10000000 + >; + atmel,nand-addr-offset = <21>; + atmel,nand-cmd-offset = <22>; + gpios = <&pioC 8 0 + &pioC 14 0 + 0 + >; + status = "disabled"; + }; + + usb0: ohci@00600000 { + compatible = "atmel,at91rm9200-ohci", "usb-ohci"; + reg = <0x00600000 0x100000>; + interrupts = <22 4>; + status = "disabled"; + }; + + usb1: ehci@00700000 { + compatible = "atmel,at91sam9g45-ehci", "usb-ehci"; + reg = <0x00700000 0x100000>; + interrupts = <22 4>; + status = "disabled"; + }; + }; + + i2c@0 { + compatible = "i2c-gpio"; + gpios = <&pioA 30 0 /* sda */ + &pioA 31 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c@1 { + compatible = "i2c-gpio"; + gpios = <&pioC 0 0 /* sda */ + &pioC 1 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c@2 { + compatible = "i2c-gpio"; + gpios = <&pioB 4 0 /* sda */ + &pioB 5 0 /* scl */ + >; + i2c-gpio,sda-open-drain; + i2c-gpio,scl-open-drain; + i2c-gpio,delay-us = <2>; /* ~100 kHz */ + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; }; }; diff --git a/arch/arm/boot/dts/at91sam9x5cm.dtsi b/arch/arm/boot/dts/at91sam9x5cm.dtsi index 64ae3e890259..67936f83c694 100644 --- a/arch/arm/boot/dts/at91sam9x5cm.dtsi +++ b/arch/arm/boot/dts/at91sam9x5cm.dtsi @@ -12,6 +12,51 @@ reg = <0x20000000 0x8000000>; }; + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + }; + + ahb { + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x40000>; + }; + + uboot@40000 { + label = "u-boot"; + reg = <0x40000 0x80000>; + }; + + ubootenv@c0000 { + label = "U-Boot Env"; + reg = <0xc0000 0x140000>; + }; + + kernel@200000 { + label = "kernel"; + reg = <0x200000 0x600000>; + }; + + rootfs@800000 { + label = "rootfs"; + reg = <0x800000 0x1f800000>; + }; + }; + }; + leds { compatible = "gpio-leds"; diff --git a/arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi b/arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi new file mode 100644 index 000000000000..ad3eca17c436 --- /dev/null +++ b/arch/arm/boot/dts/usb_a9g20-dab-mmx.dtsi @@ -0,0 +1,96 @@ +/* + * calao-dab-mmx.dtsi - Device Tree Include file for Calao DAB-MMX Daughter Board + * + * Copyright (C) 2011 Jean-Christophe PLAGNIOL-VILLARD <plagnioj@jcrosoft.com> + * + * Licensed under GPLv2. + */ + +/ { + ahb { + apb { + usart1: serial@fffb4000 { + status = "okay"; + }; + + usart3: serial@fffd0000 { + status = "okay"; + }; + }; + }; + + i2c-gpio@0 { + status = "okay"; + }; + + leds { + compatible = "gpio-leds"; + + user_led1 { + label = "user_led1"; + gpios = <&pioB 20 1>; + }; + +/* +* led already used by mother board but active as high +* user_led2 { +* label = "user_led2"; +* gpios = <&pioB 21 1>; +* }; +*/ + user_led3 { + label = "user_led3"; + gpios = <&pioB 22 1>; + }; + + user_led4 { + label = "user_led4"; + gpios = <&pioB 23 1>; + }; + + red { + label = "red"; + gpios = <&pioB 24 1>; + }; + + orange { + label = "orange"; + gpios = <&pioB 30 1>; + }; + + green { + label = "green"; + gpios = <&pioB 31 1>; + }; + }; + + gpio_keys { + compatible = "gpio-keys"; + #address-cells = <1>; + #size-cells = <0>; + + user_pb1 { + label = "user_pb1"; + gpios = <&pioB 25 1>; + linux,code = <0x100>; + }; + + user_pb2 { + label = "user_pb2"; + gpios = <&pioB 13 1>; + linux,code = <0x101>; + }; + + user_pb3 { + label = "user_pb3"; + gpios = <&pioA 26 1>; + linux,code = <0x102>; + }; + + user_pb4 { + label = "user_pb4"; + gpios = <&pioC 9 1>; + linux,code = <0x103>; + }; + }; +}; diff --git a/arch/arm/boot/dts/usb_a9g20.dts b/arch/arm/boot/dts/usb_a9g20.dts index d74545a2a77c..748d4c2f889f 100644 --- a/arch/arm/boot/dts/usb_a9g20.dts +++ b/arch/arm/boot/dts/usb_a9g20.dts @@ -13,13 +13,24 @@ compatible = "calao,usb-a9g20", "atmel,at91sam9g20", "atmel,at91sam9"; chosen { - bootargs = "mem=64M console=ttyS0,115200 mtdparts=atmel_nand:128k(at91bootstrap),256k(barebox)ro,128k(bareboxenv),128k(bareboxenv2),4M(kernel),120M(rootfs),-(data) root=/dev/mtdblock5 rw rootfstype=ubifs"; + bootargs = "mem=64M console=ttyS0,115200 root=/dev/mtdblock5 rw rootfstype=ubifs"; }; memory@20000000 { reg = <0x20000000 0x4000000>; }; + clocks { + #address-cells = <1>; + #size-cells = <1>; + ranges; + + main_clock: clock@0 { + compatible = "atmel,osc", "fixed-clock"; + clock-frequency = <12000000>; + }; + }; + ahb { apb { dbgu: serial@fffff200 { @@ -31,6 +42,53 @@ status = "okay"; }; }; + + nand0: nand@40000000 { + nand-bus-width = <8>; + nand-ecc-mode = "soft"; + nand-on-flash-bbt; + status = "okay"; + + at91bootstrap@0 { + label = "at91bootstrap"; + reg = <0x0 0x20000>; + }; + + barebox@20000 { + label = "barebox"; + reg = <0x20000 0x40000>; + }; + + bareboxenv@60000 { + label = "bareboxenv"; + reg = <0x60000 0x20000>; + }; + + bareboxenv2@80000 { + label = "bareboxenv2"; + reg = <0x80000 0x20000>; + }; + + kernel@a0000 { + label = "kernel"; + reg = <0xa0000 0x400000>; + }; + + rootfs@4a0000 { + label = "rootfs"; + reg = <0x4a0000 0x7800000>; + }; + + data@7ca0000 { + label = "data"; + reg = <0x7ca0000 0x8360000>; + }; + }; + + usb0: ohci@00500000 { + num-ports = <2>; + status = "okay"; + }; }; leds { @@ -55,4 +113,13 @@ gpio-key,wakeup; }; }; + + i2c@0 { + status = "okay"; + + rv3029c2@56 { + compatible = "rv3029c2"; + reg = <0x56>; + }; + }; }; diff --git a/arch/arm/configs/at91sam9g20_defconfig b/arch/arm/configs/at91sam9g20_defconfig index 9123568d9a8d..994d331b2319 100644 --- a/arch/arm/configs/at91sam9g20_defconfig +++ b/arch/arm/configs/at91sam9g20_defconfig @@ -74,6 +74,8 @@ CONFIG_LEGACY_PTY_COUNT=16 CONFIG_SERIAL_ATMEL=y CONFIG_SERIAL_ATMEL_CONSOLE=y CONFIG_HW_RANDOM=y +CONFIG_I2C=y +CONFIG_I2C_GPIO=y CONFIG_SPI=y CONFIG_SPI_ATMEL=y CONFIG_SPI_SPIDEV=y @@ -105,6 +107,7 @@ CONFIG_LEDS_TRIGGERS=y CONFIG_LEDS_TRIGGER_TIMER=y CONFIG_LEDS_TRIGGER_HEARTBEAT=y CONFIG_RTC_CLASS=y +CONFIG_RTC_DRV_RV3029C2=y CONFIG_RTC_DRV_AT91SAM9=y CONFIG_EXT2_FS=y CONFIG_MSDOS_FS=y diff --git a/arch/arm/mach-at91/Kconfig b/arch/arm/mach-at91/Kconfig index e55cdcbd81fb..45db05d8d94c 100644 --- a/arch/arm/mach-at91/Kconfig +++ b/arch/arm/mach-at91/Kconfig @@ -20,9 +20,11 @@ config HAVE_AT91_USART5 config AT91_SAM9_ALT_RESET bool + default !ARCH_AT91X40 config AT91_SAM9G45_RESET bool + default !ARCH_AT91X40 menu "Atmel AT91 System-on-Chip" @@ -45,7 +47,6 @@ config ARCH_AT91SAM9260 select HAVE_AT91_USART4 select HAVE_AT91_USART5 select HAVE_NET_MACB - select AT91_SAM9_ALT_RESET config ARCH_AT91SAM9261 bool "AT91SAM9261" @@ -53,7 +54,6 @@ config ARCH_AT91SAM9261 select GENERIC_CLOCKEVENTS select HAVE_FB_ATMEL select HAVE_AT91_DBGU0 - select AT91_SAM9_ALT_RESET config ARCH_AT91SAM9G10 bool "AT91SAM9G10" @@ -61,7 +61,6 @@ config ARCH_AT91SAM9G10 select GENERIC_CLOCKEVENTS select HAVE_AT91_DBGU0 select HAVE_FB_ATMEL - select AT91_SAM9_ALT_RESET config ARCH_AT91SAM9263 bool "AT91SAM9263" @@ -70,7 +69,6 @@ config ARCH_AT91SAM9263 select HAVE_FB_ATMEL select HAVE_NET_MACB select HAVE_AT91_DBGU1 - select AT91_SAM9_ALT_RESET config ARCH_AT91SAM9RL bool "AT91SAM9RL" @@ -79,7 +77,6 @@ config ARCH_AT91SAM9RL select HAVE_AT91_USART3 select HAVE_FB_ATMEL select HAVE_AT91_DBGU0 - select AT91_SAM9_ALT_RESET config ARCH_AT91SAM9G20 bool "AT91SAM9G20" @@ -90,7 +87,6 @@ config ARCH_AT91SAM9G20 select HAVE_AT91_USART4 select HAVE_AT91_USART5 select HAVE_NET_MACB - select AT91_SAM9_ALT_RESET config ARCH_AT91SAM9G45 bool "AT91SAM9G45" @@ -100,7 +96,6 @@ config ARCH_AT91SAM9G45 select HAVE_FB_ATMEL select HAVE_NET_MACB select HAVE_AT91_DBGU1 - select AT91_SAM9G45_RESET config ARCH_AT91SAM9X5 bool "AT91SAM9x5 family" @@ -109,7 +104,6 @@ config ARCH_AT91SAM9X5 select HAVE_FB_ATMEL select HAVE_NET_MACB select HAVE_AT91_DBGU0 - select AT91_SAM9G45_RESET config ARCH_AT91X40 bool "AT91x40" diff --git a/arch/arm/mach-at91/at91sam9260.c b/arch/arm/mach-at91/at91sam9260.c index 14b5a9c9a514..d1e5750a6a04 100644 --- a/arch/arm/mach-at91/at91sam9260.c +++ b/arch/arm/mach-at91/at91sam9260.c @@ -216,6 +216,7 @@ static struct clk_lookup periph_clocks_lookups[] = { CLKDEV_CON_DEV_ID("t0_clk", "fffdc000.timer", &tc3_clk), CLKDEV_CON_DEV_ID("t1_clk", "fffdc000.timer", &tc4_clk), CLKDEV_CON_DEV_ID("t2_clk", "fffdc000.timer", &tc5_clk), + CLKDEV_CON_DEV_ID("hclk", "500000.ohci", &ohci_clk), /* fake hclk clock */ CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &ohci_clk), CLKDEV_CON_ID("pioA", &pioA_clk), diff --git a/arch/arm/mach-at91/at91sam9g45.c b/arch/arm/mach-at91/at91sam9g45.c index 0014573dfe17..df3bceacc86c 100644 --- a/arch/arm/mach-at91/at91sam9g45.c +++ b/arch/arm/mach-at91/at91sam9g45.c @@ -232,6 +232,8 @@ static struct clk_lookup periph_clocks_lookups[] = { /* more tc lookup table for DT entries */ CLKDEV_CON_DEV_ID("t0_clk", "fff7c000.timer", &tcb0_clk), CLKDEV_CON_DEV_ID("t0_clk", "fffd4000.timer", &tcb0_clk), + CLKDEV_CON_DEV_ID("hclk", "700000.ohci", &uhphs_clk), + CLKDEV_CON_DEV_ID("ehci_clk", "800000.ehci", &uhphs_clk), /* fake hclk clock */ CLKDEV_CON_DEV_ID("hclk", "at91_ohci", &uhphs_clk), CLKDEV_CON_ID("pioA", &pioA_clk), diff --git a/arch/arm/mach-at91/at91sam9x5.c b/arch/arm/mach-at91/at91sam9x5.c index a34d96afa746..b6831eeb7b76 100644 --- a/arch/arm/mach-at91/at91sam9x5.c +++ b/arch/arm/mach-at91/at91sam9x5.c @@ -131,7 +131,7 @@ static struct clk dma1_clk = { .type = CLK_TYPE_PERIPHERAL, }; static struct clk uhphs_clk = { - .name = "uhphs_clk", + .name = "uhphs", .pmc_mask = 1 << AT91SAM9X5_ID_UHPHS, .type = CLK_TYPE_PERIPHERAL, }; @@ -230,6 +230,9 @@ static struct clk_lookup periph_clocks_lookups[] = { /* additional fake clock for macb_hclk */ CLKDEV_CON_DEV_ID("hclk", "f802c000.ethernet", &macb0_clk), CLKDEV_CON_DEV_ID("hclk", "f8030000.ethernet", &macb1_clk), + CLKDEV_CON_DEV_ID("hclk", "600000.ohci", &uhphs_clk), + CLKDEV_CON_DEV_ID("ohci_clk", "600000.ohci", &uhphs_clk), + CLKDEV_CON_DEV_ID("ehci_clk", "700000.ehci", &uhphs_clk), }; /* @@ -299,14 +302,8 @@ static void __init at91sam9x5_map_io(void) at91_init_sram(0, AT91SAM9X5_SRAM_BASE, AT91SAM9X5_SRAM_SIZE); } -static void __init at91sam9x5_ioremap_registers(void) -{ - at91_ioremap_ramc(0, AT91SAM9X5_BASE_DDRSDRC0, 512); -} - void __init at91sam9x5_initialize(void) { - arm_pm_restart = at91sam9g45_restart; at91_extern_irq = (1 << AT91SAM9X5_ID_IRQ0); /* Register GPIO subsystem (using DT) */ @@ -314,11 +311,6 @@ void __init at91sam9x5_initialize(void) } /* -------------------------------------------------------------------- - * AT91SAM9x5 devices (temporary before modification of code) - * -------------------------------------------------------------------- */ -void __init at91_add_device_nand(struct atmel_nand_data *data) {} - -/* -------------------------------------------------------------------- * Interrupt initialization * -------------------------------------------------------------------- */ /* @@ -362,7 +354,6 @@ static unsigned int at91sam9x5_default_irq_priority[NR_AIC_IRQS] __initdata = { struct at91_init_soc __initdata at91sam9x5_soc = { .map_io = at91sam9x5_map_io, .default_irq_priority = at91sam9x5_default_irq_priority, - .ioremap_registers = at91sam9x5_ioremap_registers, .register_clocks = at91sam9x5_register_clocks, .init = at91sam9x5_initialize, }; diff --git a/arch/arm/mach-at91/board-afeb-9260v1.c b/arch/arm/mach-at91/board-afeb-9260v1.c index 3bb40694b02d..161efbaa1029 100644 --- a/arch/arm/mach-at91/board-afeb-9260v1.c +++ b/arch/arm/mach-at91/board-afeb-9260v1.c @@ -138,6 +138,7 @@ static struct atmel_nand_data __initdata afeb9260_nand_data = { .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, .bus_width_16 = 0, + .ecc_mode = NAND_ECC_SOFT, .parts = afeb9260_nand_partition, .num_parts = ARRAY_SIZE(afeb9260_nand_partition), .det_pin = -EINVAL, diff --git a/arch/arm/mach-at91/board-cam60.c b/arch/arm/mach-at91/board-cam60.c index 8510e9e54988..c6d44ee0c77e 100644 --- a/arch/arm/mach-at91/board-cam60.c +++ b/arch/arm/mach-at91/board-cam60.c @@ -140,6 +140,7 @@ static struct atmel_nand_data __initdata cam60_nand_data = { .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PA9, .enable_pin = AT91_PIN_PA7, + .ecc_mode = NAND_ECC_SOFT, .parts = cam60_nand_partition, .num_parts = ARRAY_SIZE(cam60_nand_partition), }; diff --git a/arch/arm/mach-at91/board-cpu9krea.c b/arch/arm/mach-at91/board-cpu9krea.c index 989e1c5a9ca0..5f3680e7c883 100644 --- a/arch/arm/mach-at91/board-cpu9krea.c +++ b/arch/arm/mach-at91/board-cpu9krea.c @@ -117,6 +117,7 @@ static struct atmel_nand_data __initdata cpu9krea_nand_data = { .enable_pin = AT91_PIN_PC14, .bus_width_16 = 0, .det_pin = -EINVAL, + .ecc_mode = NAND_ECC_SOFT, }; #ifdef CONFIG_MACH_CPU9260 diff --git a/arch/arm/mach-at91/board-dt.c b/arch/arm/mach-at91/board-dt.c index 583b72472ad9..c18d4d307801 100644 --- a/arch/arm/mach-at91/board-dt.c +++ b/arch/arm/mach-at91/board-dt.c @@ -19,10 +19,7 @@ #include <linux/of_irq.h> #include <linux/of_platform.h> -#include <mach/hardware.h> #include <mach/board.h> -#include <mach/system_rev.h> -#include <mach/at91sam9_smc.h> #include <asm/setup.h> #include <asm/irq.h> @@ -30,58 +27,9 @@ #include <asm/mach/map.h> #include <asm/mach/irq.h> -#include "sam9_smc.h" #include "generic.h" -static void __init ek_init_early(void) -{ - /* Initialize processor: 12.000 MHz crystal */ - at91_initialize(12000000); -} - -/* det_pin is not connected */ -static struct atmel_nand_data __initdata ek_nand_data = { - .ale = 21, - .cle = 22, - .det_pin = -EINVAL, - .rdy_pin = AT91_PIN_PC8, - .enable_pin = AT91_PIN_PC14, -}; - -static struct sam9_smc_config __initdata ek_nand_smc_config = { - .ncs_read_setup = 0, - .nrd_setup = 2, - .ncs_write_setup = 0, - .nwe_setup = 2, - - .ncs_read_pulse = 4, - .nrd_pulse = 4, - .ncs_write_pulse = 4, - .nwe_pulse = 4, - - .read_cycle = 7, - .write_cycle = 7, - - .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE, - .tdf_cycles = 3, -}; - -static void __init ek_add_device_nand(void) -{ - ek_nand_data.bus_width_16 = board_have_nand_16bit(); - /* setup bus-width (8 or 16) */ - if (ek_nand_data.bus_width_16) - ek_nand_smc_config.mode |= AT91_SMC_DBW_16; - else - ek_nand_smc_config.mode |= AT91_SMC_DBW_8; - - /* configure chip-select 3 (NAND) */ - sam9_smc_configure(0, 3, &ek_nand_smc_config); - - at91_add_device_nand(&ek_nand_data); -} - static const struct of_device_id irq_of_match[] __initconst = { { .compatible = "atmel,at91rm9200-aic", .data = at91_aic_of_init }, @@ -98,9 +46,6 @@ static void __init at91_dt_init_irq(void) static void __init at91_dt_device_init(void) { of_platform_populate(NULL, of_default_bus_match_table, NULL, NULL); - - /* NAND */ - ek_add_device_nand(); } static const char *at91_dt_board_compat[] __initdata = { @@ -114,7 +59,7 @@ DT_MACHINE_START(at91sam_dt, "Atmel AT91SAM (Device Tree)") /* Maintainer: Atmel */ .timer = &at91sam926x_timer, .map_io = at91_map_io, - .init_early = ek_init_early, + .init_early = at91_dt_initialize, .init_irq = at91_dt_init_irq, .init_machine = at91_dt_device_init, .dt_compat = at91_dt_board_compat, diff --git a/arch/arm/mach-at91/board-kb9202.c b/arch/arm/mach-at91/board-kb9202.c index bb9914582013..59b92aab9bcf 100644 --- a/arch/arm/mach-at91/board-kb9202.c +++ b/arch/arm/mach-at91/board-kb9202.c @@ -108,6 +108,7 @@ static struct atmel_nand_data __initdata kb9202_nand_data = { .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC29, .enable_pin = AT91_PIN_PC28, + .ecc_mode = NAND_ECC_SOFT, .parts = kb9202_nand_partition, .num_parts = ARRAY_SIZE(kb9202_nand_partition), }; diff --git a/arch/arm/mach-at91/board-neocore926.c b/arch/arm/mach-at91/board-neocore926.c index 3f8617c0e04e..57d5f6a4726a 100644 --- a/arch/arm/mach-at91/board-neocore926.c +++ b/arch/arm/mach-at91/board-neocore926.c @@ -190,6 +190,7 @@ static struct atmel_nand_data __initdata neocore926_nand_data = { .rdy_pin = AT91_PIN_PB19, .rdy_pin_active_low = 1, .enable_pin = AT91_PIN_PD15, + .ecc_mode = NAND_ECC_SOFT, .parts = neocore926_nand_partition, .num_parts = ARRAY_SIZE(neocore926_nand_partition), .det_pin = -EINVAL, diff --git a/arch/arm/mach-at91/board-qil-a9260.c b/arch/arm/mach-at91/board-qil-a9260.c index e029d220cb84..b6ed5ed7081a 100644 --- a/arch/arm/mach-at91/board-qil-a9260.c +++ b/arch/arm/mach-at91/board-qil-a9260.c @@ -138,6 +138,8 @@ static struct atmel_nand_data __initdata ek_nand_data = { .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, .parts = ek_nand_partition, .num_parts = ARRAY_SIZE(ek_nand_partition), }; diff --git a/arch/arm/mach-at91/board-rm9200dk.c b/arch/arm/mach-at91/board-rm9200dk.c index 9083df04e7ed..01332aa538b2 100644 --- a/arch/arm/mach-at91/board-rm9200dk.c +++ b/arch/arm/mach-at91/board-rm9200dk.c @@ -150,6 +150,8 @@ static struct atmel_nand_data __initdata dk_nand_data = { .det_pin = AT91_PIN_PB1, .rdy_pin = AT91_PIN_PC2, .enable_pin = -EINVAL, + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, .parts = dk_nand_partition, .num_parts = ARRAY_SIZE(dk_nand_partition), }; diff --git a/arch/arm/mach-at91/board-sam9-l9260.c b/arch/arm/mach-at91/board-sam9-l9260.c index 84bce587735f..e8b116b6cba6 100644 --- a/arch/arm/mach-at91/board-sam9-l9260.c +++ b/arch/arm/mach-at91/board-sam9-l9260.c @@ -139,6 +139,7 @@ static struct atmel_nand_data __initdata ek_nand_data = { .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, + .ecc_mode = NAND_ECC_SOFT, .parts = ek_nand_partition, .num_parts = ARRAY_SIZE(ek_nand_partition), }; diff --git a/arch/arm/mach-at91/board-sam9260ek.c b/arch/arm/mach-at91/board-sam9260ek.c index be8233bcabdc..d5aec55b0eb4 100644 --- a/arch/arm/mach-at91/board-sam9260ek.c +++ b/arch/arm/mach-at91/board-sam9260ek.c @@ -181,6 +181,8 @@ static struct atmel_nand_data __initdata ek_nand_data = { .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, .parts = ek_nand_partition, .num_parts = ARRAY_SIZE(ek_nand_partition), }; diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c index 40895072a1a7..c3f994462864 100644 --- a/arch/arm/mach-at91/board-sam9261ek.c +++ b/arch/arm/mach-at91/board-sam9261ek.c @@ -187,6 +187,8 @@ static struct atmel_nand_data __initdata ek_nand_data = { .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC15, .enable_pin = AT91_PIN_PC14, + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, .parts = ek_nand_partition, .num_parts = ARRAY_SIZE(ek_nand_partition), }; diff --git a/arch/arm/mach-at91/board-sam9263ek.c b/arch/arm/mach-at91/board-sam9263ek.c index 29f66052fe63..66f0ddf4b2ae 100644 --- a/arch/arm/mach-at91/board-sam9263ek.c +++ b/arch/arm/mach-at91/board-sam9263ek.c @@ -187,6 +187,8 @@ static struct atmel_nand_data __initdata ek_nand_data = { .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PA22, .enable_pin = AT91_PIN_PD15, + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, .parts = ek_nand_partition, .num_parts = ARRAY_SIZE(ek_nand_partition), }; diff --git a/arch/arm/mach-at91/board-sam9g20ek.c b/arch/arm/mach-at91/board-sam9g20ek.c index 843d6286c6f4..8923ec9f5831 100644 --- a/arch/arm/mach-at91/board-sam9g20ek.c +++ b/arch/arm/mach-at91/board-sam9g20ek.c @@ -166,6 +166,8 @@ static struct atmel_nand_data __initdata ek_nand_data = { .rdy_pin = AT91_PIN_PC13, .enable_pin = AT91_PIN_PC14, .det_pin = -EINVAL, + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, .parts = ek_nand_partition, .num_parts = ARRAY_SIZE(ek_nand_partition), }; diff --git a/arch/arm/mach-at91/board-sam9m10g45ek.c b/arch/arm/mach-at91/board-sam9m10g45ek.c index 57497e2b8878..e1bea73e6b30 100644 --- a/arch/arm/mach-at91/board-sam9m10g45ek.c +++ b/arch/arm/mach-at91/board-sam9m10g45ek.c @@ -148,6 +148,8 @@ static struct atmel_nand_data __initdata ek_nand_data = { .rdy_pin = AT91_PIN_PC8, .enable_pin = AT91_PIN_PC14, .det_pin = -EINVAL, + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, .parts = ek_nand_partition, .num_parts = ARRAY_SIZE(ek_nand_partition), }; diff --git a/arch/arm/mach-at91/board-sam9rlek.c b/arch/arm/mach-at91/board-sam9rlek.c index c1366d0032bf..b109ce2ba864 100644 --- a/arch/arm/mach-at91/board-sam9rlek.c +++ b/arch/arm/mach-at91/board-sam9rlek.c @@ -94,6 +94,8 @@ static struct atmel_nand_data __initdata ek_nand_data = { .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PD17, .enable_pin = AT91_PIN_PB6, + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, .parts = ek_nand_partition, .num_parts = ARRAY_SIZE(ek_nand_partition), }; diff --git a/arch/arm/mach-at91/board-snapper9260.c b/arch/arm/mach-at91/board-snapper9260.c index 3c2e3fcc310c..ebc9d01ce742 100644 --- a/arch/arm/mach-at91/board-snapper9260.c +++ b/arch/arm/mach-at91/board-snapper9260.c @@ -110,6 +110,7 @@ static struct atmel_nand_data __initdata snapper9260_nand_data = { .bus_width_16 = 0, .enable_pin = -EINVAL, .det_pin = -EINVAL, + .ecc_mode = NAND_ECC_SOFT, }; static struct sam9_smc_config __initdata snapper9260_nand_smc_config = { diff --git a/arch/arm/mach-at91/board-stamp9g20.c b/arch/arm/mach-at91/board-stamp9g20.c index 72eb3b4d9ab6..7640049410a0 100644 --- a/arch/arm/mach-at91/board-stamp9g20.c +++ b/arch/arm/mach-at91/board-stamp9g20.c @@ -86,6 +86,7 @@ static struct atmel_nand_data __initdata nand_data = { .enable_pin = AT91_PIN_PC14, .bus_width_16 = 0, .det_pin = -EINVAL, + .ecc_mode = NAND_ECC_SOFT, }; static struct sam9_smc_config __initdata nand_smc_config = { diff --git a/arch/arm/mach-at91/board-usb-a926x.c b/arch/arm/mach-at91/board-usb-a926x.c index 26c36fc2d1e5..b7483a3d0980 100644 --- a/arch/arm/mach-at91/board-usb-a926x.c +++ b/arch/arm/mach-at91/board-usb-a926x.c @@ -198,6 +198,8 @@ static struct atmel_nand_data __initdata ek_nand_data = { .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PA22, .enable_pin = AT91_PIN_PD15, + .ecc_mode = NAND_ECC_SOFT, + .on_flash_bbt = 1, .parts = ek_nand_partition, .num_parts = ARRAY_SIZE(ek_nand_partition), }; diff --git a/arch/arm/mach-at91/board-yl-9200.c b/arch/arm/mach-at91/board-yl-9200.c index 52f460768f71..38dd279d30b2 100644 --- a/arch/arm/mach-at91/board-yl-9200.c +++ b/arch/arm/mach-at91/board-yl-9200.c @@ -182,6 +182,7 @@ static struct atmel_nand_data __initdata yl9200_nand_data = { .det_pin = -EINVAL, .rdy_pin = AT91_PIN_PC14, /* R/!B (Sheet10) */ .enable_pin = AT91_PIN_PC15, /* !CE (Sheet10) */ + .ecc_mode = NAND_ECC_SOFT, .parts = yl9200_nand_partition, .num_parts = ARRAY_SIZE(yl9200_nand_partition), }; diff --git a/arch/arm/mach-at91/clock.c b/arch/arm/mach-at91/clock.c index be51ca7f694d..a0f4d7424cdc 100644 --- a/arch/arm/mach-at91/clock.c +++ b/arch/arm/mach-at91/clock.c @@ -23,6 +23,7 @@ #include <linux/delay.h> #include <linux/clk.h> #include <linux/io.h> +#include <linux/of_address.h> #include <mach/hardware.h> #include <mach/at91_pmc.h> @@ -671,16 +672,12 @@ static void __init at91_upll_usbfs_clock_init(unsigned long main_clock) uhpck.rate_hz /= 1 + ((at91_pmc_read(AT91_PMC_USB) & AT91_PMC_OHCIUSBDIV) >> 8); } -int __init at91_clock_init(unsigned long main_clock) +static int __init at91_pmc_init(unsigned long main_clock) { unsigned tmp, freq, mckr; int i; int pll_overclock = false; - at91_pmc_base = ioremap(AT91_PMC, 256); - if (!at91_pmc_base) - panic("Impossible to ioremap AT91_PMC 0x%x\n", AT91_PMC); - /* * When the bootloader initialized the main oscillator correctly, * there's no problem using the cycle counter. But if it didn't, @@ -802,6 +799,55 @@ int __init at91_clock_init(unsigned long main_clock) return 0; } +#if defined(CONFIG_OF) +static struct of_device_id pmc_ids[] = { + { .compatible = "atmel,at91rm9200-pmc" }, + { /*sentinel*/ } +}; + +static struct of_device_id osc_ids[] = { + { .compatible = "atmel,osc" }, + { /*sentinel*/ } +}; + +int __init at91_dt_clock_init(void) +{ + struct device_node *np; + u32 main_clock = 0; + + np = of_find_matching_node(NULL, pmc_ids); + if (!np) + panic("unable to find compatible pmc node in dtb\n"); + + at91_pmc_base = of_iomap(np, 0); + if (!at91_pmc_base) + panic("unable to map pmc cpu registers\n"); + + of_node_put(np); + + /* retrieve the freqency of fixed clocks from device tree */ + np = of_find_matching_node(NULL, osc_ids); + if (np) { + u32 rate; + if (!of_property_read_u32(np, "clock-frequency", &rate)) + main_clock = rate; + } + + of_node_put(np); + + return at91_pmc_init(main_clock); +} +#endif + +int __init at91_clock_init(unsigned long main_clock) +{ + at91_pmc_base = ioremap(AT91_PMC, 256); + if (!at91_pmc_base) + panic("Impossible to ioremap AT91_PMC 0x%x\n", AT91_PMC); + + return at91_pmc_init(main_clock); +} + /* * Several unused clocks may be active. Turn them off. */ diff --git a/arch/arm/mach-at91/generic.h b/arch/arm/mach-at91/generic.h index 459f01a4a546..dd9b346c451d 100644 --- a/arch/arm/mach-at91/generic.h +++ b/arch/arm/mach-at91/generic.h @@ -20,6 +20,7 @@ extern void __init at91_init_sram(int bank, unsigned long base, extern void __init at91rm9200_set_type(int type); extern void __init at91_initialize(unsigned long main_clock); extern void __init at91x40_initialize(unsigned long main_clock); +extern void __init at91_dt_initialize(void); /* Interrupts */ extern void __init at91_init_irq_default(void); @@ -52,6 +53,7 @@ extern void __init at91sam9rl_set_console_clock(int id); extern void __init at91sam9g45_set_console_clock(int id); #ifdef CONFIG_AT91_PMC_UNIT extern int __init at91_clock_init(unsigned long main_clock); +extern int __init at91_dt_clock_init(void); #else static int inline at91_clock_init(unsigned long main_clock) { return 0; } #endif diff --git a/arch/arm/mach-at91/include/mach/at91_shdwc.h b/arch/arm/mach-at91/include/mach/at91_shdwc.h index 1d4fe822c77a..60478ea8bd46 100644 --- a/arch/arm/mach-at91/include/mach/at91_shdwc.h +++ b/arch/arm/mach-at91/include/mach/at91_shdwc.h @@ -36,9 +36,11 @@ extern void __iomem *at91_shdwc_base; #define AT91_SHDW_WKMODE0_HIGH 1 #define AT91_SHDW_WKMODE0_LOW 2 #define AT91_SHDW_WKMODE0_ANYLEVEL 3 -#define AT91_SHDW_CPTWK0 (0xf << 4) /* Counter On Wake Up 0 */ +#define AT91_SHDW_CPTWK0_MAX 0xf /* Maximum Counter On Wake Up 0 */ +#define AT91_SHDW_CPTWK0 (AT91_SHDW_CPTWK0_MAX << 4) /* Counter On Wake Up 0 */ #define AT91_SHDW_CPTWK0_(x) ((x) << 4) #define AT91_SHDW_RTTWKEN (1 << 16) /* Real Time Timer Wake-up Enable */ +#define AT91_SHDW_RTCWKEN (1 << 17) /* Real Time Clock Wake-up Enable */ #define AT91_SHDW_SR 0x08 /* Shut Down Status Register */ #define AT91_SHDW_WAKEUP0 (1 << 0) /* Wake-up 0 Status */ diff --git a/arch/arm/mach-at91/include/mach/at91sam9x5.h b/arch/arm/mach-at91/include/mach/at91sam9x5.h index a297a77d88e2..88e43d534cdf 100644 --- a/arch/arm/mach-at91/include/mach/at91sam9x5.h +++ b/arch/arm/mach-at91/include/mach/at91sam9x5.h @@ -55,11 +55,6 @@ #define AT91SAM9X5_BASE_USART2 0xf8024000 /* - * System Peripherals - */ -#define AT91SAM9X5_BASE_DDRSDRC0 0xffffe800 - -/* * Base addresses for early serial code (uncompress.h) */ #define AT91_DBGU AT91_BASE_DBGU0 diff --git a/arch/arm/mach-at91/include/mach/board.h b/arch/arm/mach-at91/include/mach/board.h index dc8d6d4f17cf..544a5d5ce416 100644 --- a/arch/arm/mach-at91/include/mach/board.h +++ b/arch/arm/mach-at91/include/mach/board.h @@ -41,6 +41,7 @@ #include <sound/atmel-ac97c.h> #include <linux/serial.h> #include <linux/platform_data/macb.h> +#include <linux/platform_data/atmel.h> /* USB Device */ struct at91_udc_data { @@ -98,20 +99,6 @@ extern void __init at91_add_device_usbh(struct at91_usbh_data *data); extern void __init at91_add_device_usbh_ohci(struct at91_usbh_data *data); extern void __init at91_add_device_usbh_ehci(struct at91_usbh_data *data); - /* NAND / SmartMedia */ -struct atmel_nand_data { - int enable_pin; /* chip enable */ - int det_pin; /* card detect */ - int rdy_pin; /* ready/busy */ - u8 rdy_pin_active_low; /* rdy_pin value is inverted */ - u8 ale; /* address line number connected to ALE */ - u8 cle; /* address line number connected to CLE */ - u8 bus_width_16; /* buswidth is 16 bit */ - u8 correction_cap; /* PMECC correction capability */ - u16 sector_size; /* Sector size for PMECC */ - struct mtd_partition *parts; - unsigned int num_parts; -}; extern void __init at91_add_device_nand(struct atmel_nand_data *data); /* I2C*/ diff --git a/arch/arm/mach-at91/pm.c b/arch/arm/mach-at91/pm.c index 6c9d5e69ac28..f630250c6b87 100644 --- a/arch/arm/mach-at91/pm.c +++ b/arch/arm/mach-at91/pm.c @@ -197,19 +197,6 @@ extern void at91_slow_clock(void __iomem *pmc, void __iomem *ramc0, extern u32 at91_slow_clock_sz; #endif -void __iomem *at91_ramc_base[2]; - -void __init at91_ioremap_ramc(int id, u32 addr, u32 size) -{ - if (id < 0 || id > 1) { - pr_emerg("Wrong RAM controller id (%d), cannot continue\n", id); - BUG(); - } - at91_ramc_base[id] = ioremap(addr, size); - if (!at91_ramc_base[id]) - panic("Impossible to ioremap ramc.%d 0x%x\n", id, addr); -} - static int at91_pm_enter(suspend_state_t state) { at91_gpio_suspend(); diff --git a/arch/arm/mach-at91/setup.c b/arch/arm/mach-at91/setup.c index 372396c2ecb6..1083739e3065 100644 --- a/arch/arm/mach-at91/setup.c +++ b/arch/arm/mach-at91/setup.c @@ -9,6 +9,7 @@ #include <linux/io.h> #include <linux/mm.h> #include <linux/pm.h> +#include <linux/of_address.h> #include <asm/mach/map.h> @@ -51,6 +52,19 @@ void __init at91_init_interrupts(unsigned int *priority) at91_gpio_irq_setup(); } +void __iomem *at91_ramc_base[2]; + +void __init at91_ioremap_ramc(int id, u32 addr, u32 size) +{ + if (id < 0 || id > 1) { + pr_emerg("Wrong RAM controller id (%d), cannot continue\n", id); + BUG(); + } + at91_ramc_base[id] = ioremap(addr, size); + if (!at91_ramc_base[id]) + panic("Impossible to ioremap ramc.%d 0x%x\n", id, addr); +} + static struct map_desc sram_desc[2] __initdata; void __init at91_init_sram(int bank, unsigned long base, unsigned int length) @@ -285,6 +299,150 @@ void __init at91_ioremap_matrix(u32 base_addr) panic("Impossible to ioremap at91_matrix_base\n"); } +#if defined(CONFIG_OF) +static struct of_device_id rstc_ids[] = { + { .compatible = "atmel,at91sam9260-rstc", .data = at91sam9_alt_restart }, + { .compatible = "atmel,at91sam9g45-rstc", .data = at91sam9g45_restart }, + { /*sentinel*/ } +}; + +static void at91_dt_rstc(void) +{ + struct device_node *np; + const struct of_device_id *of_id; + + np = of_find_matching_node(NULL, rstc_ids); + if (!np) + panic("unable to find compatible rstc node in dtb\n"); + + at91_rstc_base = of_iomap(np, 0); + if (!at91_rstc_base) + panic("unable to map rstc cpu registers\n"); + + of_id = of_match_node(rstc_ids, np); + if (!of_id) + panic("AT91: rtsc no restart function availlable\n"); + + arm_pm_restart = of_id->data; + + of_node_put(np); +} + +static struct of_device_id ramc_ids[] = { + { .compatible = "atmel,at91sam9260-sdramc" }, + { .compatible = "atmel,at91sam9g45-ddramc" }, + { /*sentinel*/ } +}; + +static void at91_dt_ramc(void) +{ + struct device_node *np; + + np = of_find_matching_node(NULL, ramc_ids); + if (!np) + panic("unable to find compatible ram conroller node in dtb\n"); + + at91_ramc_base[0] = of_iomap(np, 0); + if (!at91_ramc_base[0]) + panic("unable to map ramc[0] cpu registers\n"); + /* the controller may have 2 banks */ + at91_ramc_base[1] = of_iomap(np, 1); + + of_node_put(np); +} + +static struct of_device_id shdwc_ids[] = { + { .compatible = "atmel,at91sam9260-shdwc", }, + { .compatible = "atmel,at91sam9rl-shdwc", }, + { .compatible = "atmel,at91sam9x5-shdwc", }, + { /*sentinel*/ } +}; + +static const char *shdwc_wakeup_modes[] = { + [AT91_SHDW_WKMODE0_NONE] = "none", + [AT91_SHDW_WKMODE0_HIGH] = "high", + [AT91_SHDW_WKMODE0_LOW] = "low", + [AT91_SHDW_WKMODE0_ANYLEVEL] = "any", +}; + +const int at91_dtget_shdwc_wakeup_mode(struct device_node *np) +{ + const char *pm; + int err, i; + + err = of_property_read_string(np, "atmel,wakeup-mode", &pm); + if (err < 0) + return AT91_SHDW_WKMODE0_ANYLEVEL; + + for (i = 0; i < ARRAY_SIZE(shdwc_wakeup_modes); i++) + if (!strcasecmp(pm, shdwc_wakeup_modes[i])) + return i; + + return -ENODEV; +} + +static void at91_dt_shdwc(void) +{ + struct device_node *np; + int wakeup_mode; + u32 reg; + u32 mode = 0; + + np = of_find_matching_node(NULL, shdwc_ids); + if (!np) { + pr_debug("AT91: unable to find compatible shutdown (shdwc) conroller node in dtb\n"); + return; + } + + at91_shdwc_base = of_iomap(np, 0); + if (!at91_shdwc_base) + panic("AT91: unable to map shdwc cpu registers\n"); + + wakeup_mode = at91_dtget_shdwc_wakeup_mode(np); + if (wakeup_mode < 0) { + pr_warn("AT91: shdwc unknown wakeup mode\n"); + goto end; + } + + if (!of_property_read_u32(np, "atmel,wakeup-counter", ®)) { + if (reg > AT91_SHDW_CPTWK0_MAX) { + pr_warn("AT91: shdwc wakeup conter 0x%x > 0x%x reduce it to 0x%x\n", + reg, AT91_SHDW_CPTWK0_MAX, AT91_SHDW_CPTWK0_MAX); + reg = AT91_SHDW_CPTWK0_MAX; + } + mode |= AT91_SHDW_CPTWK0_(reg); + } + + if (of_property_read_bool(np, "atmel,wakeup-rtc-timer")) + mode |= AT91_SHDW_RTCWKEN; + + if (of_property_read_bool(np, "atmel,wakeup-rtt-timer")) + mode |= AT91_SHDW_RTTWKEN; + + at91_shdwc_write(AT91_SHDW_MR, wakeup_mode | mode); + +end: + pm_power_off = at91sam9_poweroff; + + of_node_put(np); +} + +void __init at91_dt_initialize(void) +{ + at91_dt_rstc(); + at91_dt_ramc(); + at91_dt_shdwc(); + + /* Init clock subsystem */ + at91_dt_clock_init(); + + /* Register the processor-specific clocks */ + at91_boot_soc.register_clocks(); + + at91_boot_soc.init(); +} +#endif + void __init at91_initialize(unsigned long main_clock) { at91_boot_soc.ioremap_registers(); |