diff options
Diffstat (limited to 'arch/arm/mach-omap2')
| -rw-r--r-- | arch/arm/mach-omap2/board-3430sdp.c | 21 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-3630sdp.c | 21 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-am3517crane.c | 24 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-am3517evm.c | 17 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-cm-t35.c | 20 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-cm-t3517.c | 20 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-devkit8000.c | 8 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-igep0020.c | 32 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-omap3beagle.c | 32 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-omap3evm.c | 25 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-omap3pandora.c | 21 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-omap3stalker.c | 17 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-omap3touchbook.c | 17 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-omap4panda.c | 55 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-overo.c | 16 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/board-zoom.c | 16 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/usb-host.c | 160 | ||||
| -rw-r--r-- | arch/arm/mach-omap2/usb.h | 9 |
18 files changed, 371 insertions, 160 deletions
diff --git a/arch/arm/mach-omap2/board-3430sdp.c b/arch/arm/mach-omap2/board-3430sdp.c index ce812decfaca..7eb9651dd0f7 100644 --- a/arch/arm/mach-omap2/board-3430sdp.c +++ b/arch/arm/mach-omap2/board-3430sdp.c @@ -445,16 +445,23 @@ static void enable_board_wakeup_source(void) OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP); } +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = 57, + .vcc_gpio = -EINVAL, + }, + { + .port = 2, + .reset_gpio = 61, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = 57, - .reset_gpio_port[1] = 61, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -606,6 +613,8 @@ static void __init omap_3430sdp_init(void) board_flash_init(sdp_flash_partitions, chip_sel_3430, 0); sdp3430_display_init(); enable_board_wakeup_source(); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); } diff --git a/arch/arm/mach-omap2/board-3630sdp.c b/arch/arm/mach-omap2/board-3630sdp.c index 67447bd4564f..20d6d8189240 100644 --- a/arch/arm/mach-omap2/board-3630sdp.c +++ b/arch/arm/mach-omap2/board-3630sdp.c @@ -53,16 +53,23 @@ static void enable_board_wakeup_source(void) OMAP_WAKEUP_EN | OMAP_PIN_INPUT_PULLUP); } +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = 126, + .vcc_gpio = -EINVAL, + }, + { + .port = 2, + .reset_gpio = 61, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = 126, - .reset_gpio_port[1] = 61, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -199,6 +206,8 @@ static void __init omap_sdp_init(void) board_smc91x_init(); board_flash_init(sdp_flash_partitions, chip_sel_sdp, NAND_BUSWIDTH_16); enable_board_wakeup_source(); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); } diff --git a/arch/arm/mach-omap2/board-am3517crane.c b/arch/arm/mach-omap2/board-am3517crane.c index 7d3358b2e593..fc53911d0d13 100644 --- a/arch/arm/mach-omap2/board-am3517crane.c +++ b/arch/arm/mach-omap2/board-am3517crane.c @@ -47,15 +47,17 @@ static struct omap_board_mux board_mux[] __initdata = { }; #endif +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = GPIO_USB_NRESET, + .vcc_gpio = GPIO_USB_POWER, + .vcc_polarity = 1, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = GPIO_USB_NRESET, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL }; static struct mtd_partition crane_nand_partitions[] = { @@ -131,13 +133,7 @@ static void __init am3517_crane_init(void) return; } - ret = gpio_request_one(GPIO_USB_POWER, GPIOF_OUT_INIT_HIGH, - "usb_ehci_enable"); - if (ret < 0) { - pr_err("Can not request GPIO %d\n", GPIO_USB_POWER); - return; - } - + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); am35xx_emac_init(AM35XX_DEFAULT_MDIO_FREQUENCY, 1); } diff --git a/arch/arm/mach-omap2/board-am3517evm.c b/arch/arm/mach-omap2/board-am3517evm.c index 9fb85908a61e..191f9762ba63 100644 --- a/arch/arm/mach-omap2/board-am3517evm.c +++ b/arch/arm/mach-omap2/board-am3517evm.c @@ -274,6 +274,14 @@ static __init void am3517_evm_mcbsp1_init(void) omap_ctrl_writel(devconf0, OMAP2_CONTROL_DEVCONF0); } +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = 57, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, #if defined(CONFIG_PANEL_SHARP_LQ043T1DG01) || \ @@ -282,12 +290,6 @@ static struct usbhs_omap_platform_data usbhs_bdata __initdata = { #else .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, #endif - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = 57, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -349,7 +351,6 @@ static struct omap2_hsmmc_info mmc[] = { {} /* Terminator */ }; - static void __init am3517_evm_init(void) { omap3_mux_init(board_mux, OMAP_PACKAGE_CBB); @@ -361,6 +362,8 @@ static void __init am3517_evm_init(void) /* Configure GPIO for EHCI port */ omap_mux_init_gpio(57, OMAP_PIN_OUTPUT); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); am3517_evm_hecc_init(&am3517_evm_hecc_pdata); /* DSS */ diff --git a/arch/arm/mach-omap2/board-cm-t35.c b/arch/arm/mach-omap2/board-cm-t35.c index af2bb219e214..7fda3f5f8a7f 100644 --- a/arch/arm/mach-omap2/board-cm-t35.c +++ b/arch/arm/mach-omap2/board-cm-t35.c @@ -419,15 +419,22 @@ static struct omap2_hsmmc_info mmc[] = { {} /* Terminator */ }; +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = OMAP_MAX_GPIO_LINES + 6, + .vcc_gpio = -EINVAL, + }, + { + .port = 2, + .reset_gpio = OMAP_MAX_GPIO_LINES + 7, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = OMAP_MAX_GPIO_LINES + 6, - .reset_gpio_port[1] = OMAP_MAX_GPIO_LINES + 7, - .reset_gpio_port[2] = -EINVAL }; static void __init cm_t35_init_usbh(void) @@ -444,6 +451,7 @@ static void __init cm_t35_init_usbh(void) msleep(1); } + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); } diff --git a/arch/arm/mach-omap2/board-cm-t3517.c b/arch/arm/mach-omap2/board-cm-t3517.c index a66da808cc4a..6920f6cfc97c 100644 --- a/arch/arm/mach-omap2/board-cm-t3517.c +++ b/arch/arm/mach-omap2/board-cm-t3517.c @@ -188,15 +188,22 @@ static inline void cm_t3517_init_rtc(void) {} #define HSUSB2_RESET_GPIO (147) #define USB_HUB_RESET_GPIO (152) +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = HSUSB1_RESET_GPIO, + .vcc_gpio = -EINVAL, + }, + { + .port = 2, + .reset_gpio = HSUSB2_RESET_GPIO, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data cm_t3517_ehci_pdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = HSUSB1_RESET_GPIO, - .reset_gpio_port[1] = HSUSB2_RESET_GPIO, - .reset_gpio_port[2] = -EINVAL, }; static int __init cm_t3517_init_usbh(void) @@ -213,6 +220,7 @@ static int __init cm_t3517_init_usbh(void) msleep(1); } + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&cm_t3517_ehci_pdata); return 0; diff --git a/arch/arm/mach-omap2/board-devkit8000.c b/arch/arm/mach-omap2/board-devkit8000.c index 53056c3b0836..42fbf1ef12a9 100644 --- a/arch/arm/mach-omap2/board-devkit8000.c +++ b/arch/arm/mach-omap2/board-devkit8000.c @@ -437,15 +437,7 @@ static struct platform_device *devkit8000_devices[] __initdata = { }; static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX diff --git a/arch/arm/mach-omap2/board-igep0020.c b/arch/arm/mach-omap2/board-igep0020.c index bf92678a01d0..95ccec0eeab9 100644 --- a/arch/arm/mach-omap2/board-igep0020.c +++ b/arch/arm/mach-omap2/board-igep0020.c @@ -527,26 +527,28 @@ static void __init igep_i2c_init(void) omap3_pmic_init("twl4030", &igep_twldata); } +static struct usbhs_phy_data igep2_phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = IGEP2_GPIO_USBH_NRESET, + .vcc_gpio = -EINVAL, + }, +}; + +static struct usbhs_phy_data igep3_phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = IGEP3_GPIO_USBH_NRESET, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data igep2_usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = IGEP2_GPIO_USBH_NRESET, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL, }; static struct usbhs_omap_platform_data igep3_usbhs_bdata __initdata = { - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = IGEP3_GPIO_USBH_NRESET, - .reset_gpio_port[2] = -EINVAL, }; #ifdef CONFIG_OMAP_MUX @@ -642,8 +644,10 @@ static void __init igep_init(void) if (machine_is_igep0020()) { omap_display_init(&igep2_dss_data); igep2_init_smsc911x(); + usbhs_init_phys(igep2_phy_data, ARRAY_SIZE(igep2_phy_data)); usbhs_init(&igep2_usbhs_bdata); } else { + usbhs_init_phys(igep3_phy_data, ARRAY_SIZE(igep3_phy_data)); usbhs_init(&igep3_usbhs_bdata); } } diff --git a/arch/arm/mach-omap2/board-omap3beagle.c b/arch/arm/mach-omap2/board-omap3beagle.c index c3558f93d42c..5382215a49bc 100644 --- a/arch/arm/mach-omap2/board-omap3beagle.c +++ b/arch/arm/mach-omap2/board-omap3beagle.c @@ -33,6 +33,7 @@ #include <linux/mtd/nand.h> #include <linux/mmc/host.h> #include <linux/usb/phy.h> +#include <linux/usb/nop-usb-xceiv.h> #include <linux/regulator/machine.h> #include <linux/i2c/twl.h> @@ -277,6 +278,21 @@ static struct regulator_consumer_supply beagle_vsim_supply[] = { static struct gpio_led gpio_leds[]; +/* PHY's VCC regulator might be added later, so flag that we need it */ +static struct nop_usb_xceiv_platform_data hsusb2_phy_data = { + .needs_vcc = true, +}; + +static struct usbhs_phy_data phy_data[] = { + { + .port = 2, + .reset_gpio = 147, + .vcc_gpio = -1, /* updated in beagle_twl_gpio_setup */ + .vcc_polarity = 1, /* updated in beagle_twl_gpio_setup */ + .platform_data = &hsusb2_phy_data, + }, +}; + static int beagle_twl_gpio_setup(struct device *dev, unsigned gpio, unsigned ngpio) { @@ -318,9 +334,11 @@ static int beagle_twl_gpio_setup(struct device *dev, } dvi_panel.power_down_gpio = beagle_config.dvi_pd_gpio; - gpio_request_one(gpio + TWL4030_GPIO_MAX, beagle_config.usb_pwr_level, - "nEN_USB_PWR"); + /* TWL4030_GPIO_MAX i.e. LED_GPO controls HS USB Port 2 power */ + phy_data[0].vcc_gpio = gpio + TWL4030_GPIO_MAX; + phy_data[0].vcc_polarity = beagle_config.usb_pwr_level; + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); return 0; } @@ -453,15 +471,7 @@ static struct platform_device *omap3_beagle_devices[] __initdata = { }; static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = 147, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -543,7 +553,9 @@ static void __init omap3_beagle_init(void) usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(NULL); + usbhs_init(&usbhs_bdata); + board_nand_init(omap3beagle_nand_partitions, ARRAY_SIZE(omap3beagle_nand_partitions), NAND_CS, NAND_BUSWIDTH_16, NULL); diff --git a/arch/arm/mach-omap2/board-omap3evm.c b/arch/arm/mach-omap2/board-omap3evm.c index 48789e0bb915..2de92facc8a3 100644 --- a/arch/arm/mach-omap2/board-omap3evm.c +++ b/arch/arm/mach-omap2/board-omap3evm.c @@ -496,7 +496,7 @@ struct wl12xx_platform_data omap3evm_wlan_data __initdata = { static struct regulator_consumer_supply omap3evm_vaux2_supplies[] = { REGULATOR_SUPPLY("VDD_CSIPHY1", "omap3isp"), /* OMAP ISP */ REGULATOR_SUPPLY("VDD_CSIPHY2", "omap3isp"), /* OMAP ISP */ - REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"), + REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"), /* hsusb port 2 */ REGULATOR_SUPPLY("vaux2", NULL), }; @@ -539,17 +539,16 @@ static int __init omap3_evm_i2c_init(void) return 0; } -static struct usbhs_omap_platform_data usbhs_bdata __initdata = { +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = -1, /* set at runtime */ + .vcc_gpio = -EINVAL, + }, +}; - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, +static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - /* PHY reset GPIO will be runtime programmed based on EVM version */ - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -725,7 +724,7 @@ static void __init omap3_evm_init(void) /* setup EHCI phy reset config */ omap_mux_init_gpio(21, OMAP_PIN_INPUT_PULLUP); - usbhs_bdata.reset_gpio_port[1] = 21; + phy_data[0].reset_gpio = 21; /* EVM REV >= E can supply 500mA with EXTVBUS programming */ musb_board_data.power = 500; @@ -733,10 +732,12 @@ static void __init omap3_evm_init(void) } else { /* setup EHCI phy reset on MDC */ omap_mux_init_gpio(135, OMAP_PIN_OUTPUT); - usbhs_bdata.reset_gpio_port[1] = 135; + phy_data[0].reset_gpio = 135; } usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(&musb_board_data); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); board_nand_init(omap3evm_nand_partitions, ARRAY_SIZE(omap3evm_nand_partitions), NAND_CS, diff --git a/arch/arm/mach-omap2/board-omap3pandora.c b/arch/arm/mach-omap2/board-omap3pandora.c index 2bba362148a0..1004d2aaa68f 100644 --- a/arch/arm/mach-omap2/board-omap3pandora.c +++ b/arch/arm/mach-omap2/board-omap3pandora.c @@ -346,7 +346,7 @@ static struct regulator_consumer_supply pandora_vcc_lcd_supply[] = { }; static struct regulator_consumer_supply pandora_usb_phy_supply[] = { - REGULATOR_SUPPLY("hsusb1", "ehci-omap.0"), + REGULATOR_SUPPLY("vcc", "nop_usb_xceiv.2"), /* hsusb port 2 */ }; /* ads7846 on SPI and 2 nub controllers on I2C */ @@ -561,6 +561,14 @@ fail: printk(KERN_ERR "wl1251 board initialisation failed\n"); } +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = 16, + .vcc_gpio = -EINVAL, + }, +}; + static struct platform_device *omap3pandora_devices[] __initdata = { &pandora_leds_gpio, &pandora_keys_gpio, @@ -569,15 +577,7 @@ static struct platform_device *omap3pandora_devices[] __initdata = { }; static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = 16, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -601,7 +601,10 @@ static void __init omap3pandora_init(void) spi_register_board_info(omap3pandora_spi_board_info, ARRAY_SIZE(omap3pandora_spi_board_info)); omap_ads7846_init(1, OMAP3_PANDORA_TS_GPIO, 0, NULL); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); + usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(NULL); gpmc_nand_init(&pandora_nand_data, NULL); diff --git a/arch/arm/mach-omap2/board-omap3stalker.c b/arch/arm/mach-omap2/board-omap3stalker.c index 95c10b3aa678..bf0956489899 100644 --- a/arch/arm/mach-omap2/board-omap3stalker.c +++ b/arch/arm/mach-omap2/board-omap3stalker.c @@ -358,19 +358,20 @@ static int __init omap3_stalker_i2c_init(void) #define OMAP3_STALKER_TS_GPIO 175 +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = 21, + .vcc_gpio = -EINVAL, + }, +}; + static struct platform_device *omap3_stalker_devices[] __initdata = { &keys_gpio, }; static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = 21, - .reset_gpio_port[2] = -EINVAL, }; #ifdef CONFIG_OMAP_MUX @@ -407,6 +408,8 @@ static void __init omap3_stalker_init(void) omap_sdrc_init(mt46h32m32lf6_sdrc_params, NULL); usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(NULL); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); omap_ads7846_init(1, OMAP3_STALKER_TS_GPIO, 310, NULL); diff --git a/arch/arm/mach-omap2/board-omap3touchbook.c b/arch/arm/mach-omap2/board-omap3touchbook.c index bcd44fbcd877..7da48bc42bbf 100644 --- a/arch/arm/mach-omap2/board-omap3touchbook.c +++ b/arch/arm/mach-omap2/board-omap3touchbook.c @@ -305,21 +305,22 @@ static struct omap_board_mux board_mux[] __initdata = { }; #endif +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = 147, + .vcc_gpio = -EINVAL, + }, +}; + static struct platform_device *omap3_touchbook_devices[] __initdata = { &leds_gpio, &keys_gpio, }; static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = 147, - .reset_gpio_port[2] = -EINVAL }; static void omap3_touchbook_poweroff(void) @@ -368,6 +369,8 @@ static void __init omap3_touchbook_init(void) omap_ads7846_init(4, OMAP3_TS_GPIO, 310, &ads7846_pdata); usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(NULL); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); board_nand_init(omap3touchbook_nand_partitions, ARRAY_SIZE(omap3touchbook_nand_partitions), NAND_CS, diff --git a/arch/arm/mach-omap2/board-omap4panda.c b/arch/arm/mach-omap2/board-omap4panda.c index b02c2f00609b..a71ad345f20d 100644 --- a/arch/arm/mach-omap2/board-omap4panda.c +++ b/arch/arm/mach-omap2/board-omap4panda.c @@ -31,6 +31,7 @@ #include <linux/ti_wilink_st.h> #include <linux/usb/musb.h> #include <linux/usb/phy.h> +#include <linux/usb/nop-usb-xceiv.h> #include <linux/wl12xx.h> #include <linux/irqchip/arm-gic.h> #include <linux/platform_data/omap-abe-twl6040.h> @@ -132,6 +133,22 @@ static struct platform_device btwilink_device = { .id = -1, }; +/* PHY device on HS USB Port 1 i.e. nop_usb_xceiv.1 */ +static struct nop_usb_xceiv_platform_data hsusb1_phy_data = { + /* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */ + .clk_rate = 19200000, +}; + +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 1, + .reset_gpio = GPIO_HUB_NRESET, + .vcc_gpio = GPIO_HUB_POWER, + .vcc_polarity = 1, + .platform_data = &hsusb1_phy_data, + }, +}; + static struct platform_device *panda_devices[] __initdata = { &leds_gpio, &wl1271_device, @@ -142,49 +159,19 @@ static struct platform_device *panda_devices[] __initdata = { static struct usbhs_omap_platform_data usbhs_bdata __initdata = { .port_mode[0] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[1] = OMAP_USBHS_PORT_MODE_UNUSED, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - .phy_reset = false, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = -EINVAL, - .reset_gpio_port[2] = -EINVAL -}; - -static struct gpio panda_ehci_gpios[] __initdata = { - { GPIO_HUB_POWER, GPIOF_OUT_INIT_LOW, "hub_power" }, - { GPIO_HUB_NRESET, GPIOF_OUT_INIT_LOW, "hub_nreset" }, }; static void __init omap4_ehci_init(void) { int ret; - struct clk *phy_ref_clk; /* FREF_CLK3 provides the 19.2 MHz reference clock to the PHY */ - phy_ref_clk = clk_get(NULL, "auxclk3_ck"); - if (IS_ERR(phy_ref_clk)) { - pr_err("Cannot request auxclk3\n"); - return; - } - clk_set_rate(phy_ref_clk, 19200000); - clk_prepare_enable(phy_ref_clk); - - /* disable the power to the usb hub prior to init and reset phy+hub */ - ret = gpio_request_array(panda_ehci_gpios, - ARRAY_SIZE(panda_ehci_gpios)); - if (ret) { - pr_err("Unable to initialize EHCI power/reset\n"); - return; - } - - gpio_export(GPIO_HUB_POWER, 0); - gpio_export(GPIO_HUB_NRESET, 0); - gpio_set_value(GPIO_HUB_NRESET, 1); + ret = clk_add_alias("main_clk", "nop_usb_xceiv.1", "auxclk3_ck", NULL); + if (ret) + pr_err("Failed to add main_clk alias to auxclk3_ck\n"); + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); - - /* enable power to hub */ - gpio_set_value(GPIO_HUB_POWER, 1); } static struct omap_musb_board_data musb_board_data = { diff --git a/arch/arm/mach-omap2/board-overo.c b/arch/arm/mach-omap2/board-overo.c index 86bab51154ee..ab79a4422bcc 100644 --- a/arch/arm/mach-omap2/board-overo.c +++ b/arch/arm/mach-omap2/board-overo.c @@ -458,14 +458,16 @@ static int __init overo_spi_init(void) return 0; } +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = OVERO_GPIO_USBH_NRESET, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = OVERO_GPIO_USBH_NRESET, - .reset_gpio_port[2] = -EINVAL }; #ifdef CONFIG_OMAP_MUX @@ -502,6 +504,8 @@ static void __init overo_init(void) ARRAY_SIZE(overo_nand_partitions), NAND_CS, 0, NULL); usb_bind_phy("musb-hdrc.0.auto", 0, "twl4030_usb"); usb_musb_init(NULL); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); overo_spi_init(); overo_init_smsc911x(); diff --git a/arch/arm/mach-omap2/board-zoom.c b/arch/arm/mach-omap2/board-zoom.c index 5e4d4c9fe61a..1a3dd865d8eb 100644 --- a/arch/arm/mach-omap2/board-zoom.c +++ b/arch/arm/mach-omap2/board-zoom.c @@ -92,14 +92,16 @@ static struct mtd_partition zoom_nand_partitions[] = { }, }; +static struct usbhs_phy_data phy_data[] __initdata = { + { + .port = 2, + .reset_gpio = ZOOM3_EHCI_RESET_GPIO, + .vcc_gpio = -EINVAL, + }, +}; + static struct usbhs_omap_platform_data usbhs_bdata __initdata = { - .port_mode[0] = OMAP_USBHS_PORT_MODE_UNUSED, .port_mode[1] = OMAP_EHCI_PORT_MODE_PHY, - .port_mode[2] = OMAP_USBHS_PORT_MODE_UNUSED, - .phy_reset = true, - .reset_gpio_port[0] = -EINVAL, - .reset_gpio_port[1] = ZOOM3_EHCI_RESET_GPIO, - .reset_gpio_port[2] = -EINVAL, }; static void __init omap_zoom_init(void) @@ -109,6 +111,8 @@ static void __init omap_zoom_init(void) } else if (machine_is_omap_zoom3()) { omap3_mux_init(board_mux, OMAP_PACKAGE_CBP); omap_mux_init_gpio(ZOOM3_EHCI_RESET_GPIO, OMAP_PIN_OUTPUT); + + usbhs_init_phys(phy_data, ARRAY_SIZE(phy_data)); usbhs_init(&usbhs_bdata); } diff --git a/arch/arm/mach-omap2/usb-host.c b/arch/arm/mach-omap2/usb-host.c index 5706bdccf45e..aa27d7f5cbb7 100644 --- a/arch/arm/mach-omap2/usb-host.c +++ b/arch/arm/mach-omap2/usb-host.c @@ -22,8 +22,12 @@ #include <linux/platform_device.h> #include <linux/slab.h> #include <linux/dma-mapping.h> - -#include <asm/io.h> +#include <linux/regulator/machine.h> +#include <linux/regulator/fixed.h> +#include <linux/string.h> +#include <linux/io.h> +#include <linux/gpio.h> +#include <linux/usb/phy.h> #include "soc.h" #include "omap_device.h" @@ -526,3 +530,155 @@ void __init usbhs_init(struct usbhs_omap_platform_data *pdata) } #endif + +/* Template for PHY regulators */ +static struct fixed_voltage_config hsusb_reg_config = { + /* .supply_name filled later */ + .microvolts = 3300000, + .gpio = -1, /* updated later */ + .startup_delay = 70000, /* 70msec */ + .enable_high = 1, /* updated later */ + .enabled_at_boot = 0, /* keep in RESET */ + /* .init_data filled later */ +}; + +static const char *nop_name = "nop_usb_xceiv"; /* NOP PHY driver */ +static const char *reg_name = "reg-fixed-voltage"; /* Regulator driver */ + +/** + * usbhs_add_regulator - Add a gpio based fixed voltage regulator device + * @name: name for the regulator + * @dev_id: device id of the device this regulator supplies power to + * @dev_supply: supply name that the device expects + * @gpio: GPIO number + * @polarity: 1 - Active high, 0 - Active low + */ +static int usbhs_add_regulator(char *name, char *dev_id, char *dev_supply, + int gpio, int polarity) +{ + struct regulator_consumer_supply *supplies; + struct regulator_init_data *reg_data; + struct fixed_voltage_config *config; + struct platform_device *pdev; + int ret; + + supplies = kzalloc(sizeof(*supplies), GFP_KERNEL); + if (!supplies) + return -ENOMEM; + + supplies->supply = dev_supply; + supplies->dev_name = dev_id; + + reg_data = kzalloc(sizeof(*reg_data), GFP_KERNEL); + if (!reg_data) + return -ENOMEM; + + reg_data->constraints.valid_ops_mask = REGULATOR_CHANGE_STATUS; + reg_data->consumer_supplies = supplies; + reg_data->num_consumer_supplies = 1; + + config = kmemdup(&hsusb_reg_config, sizeof(hsusb_reg_config), + GFP_KERNEL); + if (!config) + return -ENOMEM; + + config->supply_name = name; + config->gpio = gpio; + config->enable_high = polarity; + config->init_data = reg_data; + + /* create a regulator device */ + pdev = kzalloc(sizeof(*pdev), GFP_KERNEL); + if (!pdev) + return -ENOMEM; + + pdev->id = PLATFORM_DEVID_AUTO; + pdev->name = reg_name; + pdev->dev.platform_data = config; + + ret = platform_device_register(pdev); + if (ret) + pr_err("%s: Failed registering regulator %s for %s\n", + __func__, name, dev_id); + + return ret; +} + +int usbhs_init_phys(struct usbhs_phy_data *phy, int num_phys) +{ + char *rail_name; + int i, len; + struct platform_device *pdev; + char *phy_id; + + /* the phy_id will be something like "nop_usb_xceiv.1" */ + len = strlen(nop_name) + 3; /* 3 -> ".1" and NULL terminator */ + + for (i = 0; i < num_phys; i++) { + + if (!phy->port) { + pr_err("%s: Invalid port 0. Must start from 1\n", + __func__); + continue; + } + + /* do we need a NOP PHY device ? */ + if (!gpio_is_valid(phy->reset_gpio) && + !gpio_is_valid(phy->vcc_gpio)) + continue; + + /* create a NOP PHY device */ + pdev = kzalloc(sizeof(*pdev), GFP_KERNEL); + if (!pdev) + return -ENOMEM; + + pdev->id = phy->port; + pdev->name = nop_name; + pdev->dev.platform_data = phy->platform_data; + + phy_id = kmalloc(len, GFP_KERNEL); + if (!phy_id) + return -ENOMEM; + + scnprintf(phy_id, len, "nop_usb_xceiv.%d\n", + pdev->id); + + if (platform_device_register(pdev)) { + pr_err("%s: Failed to register device %s\n", + __func__, phy_id); + continue; + } + + usb_bind_phy("ehci-omap.0", phy->port - 1, phy_id); + + /* Do we need RESET regulator ? */ + if (gpio_is_valid(phy->reset_gpio)) { + + rail_name = kmalloc(13, GFP_KERNEL); + if (!rail_name) + return -ENOMEM; + + scnprintf(rail_name, 13, "hsusb%d_reset", phy->port); + + usbhs_add_regulator(rail_name, phy_id, "reset", + phy->reset_gpio, 1); + } + + /* Do we need VCC regulator ? */ + if (gpio_is_valid(phy->vcc_gpio)) { + + rail_name = kmalloc(13, GFP_KERNEL); + if (!rail_name) + return -ENOMEM; + + scnprintf(rail_name, 13, "hsusb%d_vcc", phy->port); + + usbhs_add_regulator(rail_name, phy_id, "vcc", + phy->vcc_gpio, phy->vcc_polarity); + } + + phy++; + } + + return 0; +} diff --git a/arch/arm/mach-omap2/usb.h b/arch/arm/mach-omap2/usb.h index 3319f5cf47a3..e7261ebcf7b0 100644 --- a/arch/arm/mach-omap2/usb.h +++ b/arch/arm/mach-omap2/usb.h @@ -53,8 +53,17 @@ #define USBPHY_OTGSESSEND_EN (1 << 20) #define USBPHY_DATA_POLARITY (1 << 23) +struct usbhs_phy_data { + int port; /* 1 indexed port number */ + int reset_gpio; + int vcc_gpio; + bool vcc_polarity; /* 1 active high, 0 active low */ + void *platform_data; +}; + extern void usb_musb_init(struct omap_musb_board_data *board_data); extern void usbhs_init(struct usbhs_omap_platform_data *pdata); +extern int usbhs_init_phys(struct usbhs_phy_data *phy, int num_phys); extern void am35x_musb_reset(void); extern void am35x_musb_phy_power(u8 on); |