summaryrefslogtreecommitdiff
path: root/arch/arm/mach-at91/board-sam9261ek.c
diff options
context:
space:
mode:
Diffstat (limited to 'arch/arm/mach-at91/board-sam9261ek.c')
-rw-r--r--arch/arm/mach-at91/board-sam9261ek.c80
1 files changed, 65 insertions, 15 deletions
diff --git a/arch/arm/mach-at91/board-sam9261ek.c b/arch/arm/mach-at91/board-sam9261ek.c
index 4977409d4fc6..d5266da55311 100644
--- a/arch/arm/mach-at91/board-sam9261ek.c
+++ b/arch/arm/mach-at91/board-sam9261ek.c
@@ -47,7 +47,9 @@
#include <mach/board.h>
#include <mach/gpio.h>
#include <mach/at91sam9_smc.h>
+#include <mach/at91_shdwc.h>
+#include "sam9_smc.h"
#include "generic.h"
@@ -76,7 +78,7 @@ static void __init ek_init_irq(void)
* DM9000 ethernet device
*/
#if defined(CONFIG_DM9000)
-static struct resource at91sam9261_dm9000_resource[] = {
+static struct resource dm9000_resource[] = {
[0] = {
.start = AT91_CHIPSELECT_2,
.end = AT91_CHIPSELECT_2 + 3,
@@ -98,27 +100,42 @@ static struct dm9000_plat_data dm9000_platdata = {
.flags = DM9000_PLATF_16BITONLY,
};
-static struct platform_device at91sam9261_dm9000_device = {
+static struct platform_device dm9000_device = {
.name = "dm9000",
.id = 0,
- .num_resources = ARRAY_SIZE(at91sam9261_dm9000_resource),
- .resource = at91sam9261_dm9000_resource,
+ .num_resources = ARRAY_SIZE(dm9000_resource),
+ .resource = dm9000_resource,
.dev = {
.platform_data = &dm9000_platdata,
}
};
+/*
+ * SMC timings for the DM9000.
+ * Note: These timings were calculated for MASTER_CLOCK = 100000000 according to the DM9000 timings.
+ */
+static struct sam9_smc_config __initdata dm9000_smc_config = {
+ .ncs_read_setup = 0,
+ .nrd_setup = 2,
+ .ncs_write_setup = 0,
+ .nwe_setup = 2,
+
+ .ncs_read_pulse = 8,
+ .nrd_pulse = 4,
+ .ncs_write_pulse = 8,
+ .nwe_pulse = 4,
+
+ .read_cycle = 16,
+ .write_cycle = 16,
+
+ .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16,
+ .tdf_cycles = 1,
+};
+
static void __init ek_add_device_dm9000(void)
{
- /*
- * Configure Chip-Select 2 on SMC for the DM9000.
- * Note: These timings were calculated for MASTER_CLOCK = 100000000
- * according to the DM9000 timings.
- */
- at91_sys_write(AT91_SMC_SETUP(2), AT91_SMC_NWESETUP_(2) | AT91_SMC_NCS_WRSETUP_(0) | AT91_SMC_NRDSETUP_(2) | AT91_SMC_NCS_RDSETUP_(0));
- at91_sys_write(AT91_SMC_PULSE(2), AT91_SMC_NWEPULSE_(4) | AT91_SMC_NCS_WRPULSE_(8) | AT91_SMC_NRDPULSE_(4) | AT91_SMC_NCS_RDPULSE_(8));
- at91_sys_write(AT91_SMC_CYCLE(2), AT91_SMC_NWECYCLE_(16) | AT91_SMC_NRDCYCLE_(16));
- at91_sys_write(AT91_SMC_MODE(2), AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE | AT91_SMC_BAT_WRITE | AT91_SMC_DBW_16 | AT91_SMC_TDF_(1));
+ /* Configure chip-select 2 (DM9000) */
+ sam9_smc_configure(2, &dm9000_smc_config);
/* Configure Reset signal as output */
at91_set_gpio_output(AT91_PIN_PC10, 0);
@@ -126,7 +143,7 @@ static void __init ek_add_device_dm9000(void)
/* Configure Interrupt pin as input, no pull-up */
at91_set_gpio_input(AT91_PIN_PC11, 0);
- platform_device_register(&at91sam9261_dm9000_device);
+ platform_device_register(&dm9000_device);
}
#else
static void __init ek_add_device_dm9000(void) {}
@@ -197,6 +214,39 @@ static struct atmel_nand_data __initdata ek_nand_data = {
#endif
};
+static struct sam9_smc_config __initdata ek_nand_smc_config = {
+ .ncs_read_setup = 0,
+ .nrd_setup = 1,
+ .ncs_write_setup = 0,
+ .nwe_setup = 1,
+
+ .ncs_read_pulse = 3,
+ .nrd_pulse = 3,
+ .ncs_write_pulse = 3,
+ .nwe_pulse = 3,
+
+ .read_cycle = 5,
+ .write_cycle = 5,
+
+ .mode = AT91_SMC_READMODE | AT91_SMC_WRITEMODE | AT91_SMC_EXNWMODE_DISABLE,
+ .tdf_cycles = 2,
+};
+
+static void __init ek_add_device_nand(void)
+{
+ /* setup bus-width (8 or 16) */
+ if (ek_nand_data.bus_width_16)
+ ek_nand_smc_config.mode |= AT91_SMC_DBW_16;
+ else
+ ek_nand_smc_config.mode |= AT91_SMC_DBW_8;
+
+ /* configure chip-select 3 (NAND) */
+ sam9_smc_configure(3, &ek_nand_smc_config);
+
+ at91_add_device_nand(&ek_nand_data);
+}
+
+
/*
* ADS7846 Touchscreen
*/
@@ -525,7 +575,7 @@ static void __init ek_board_init(void)
/* I2C */
at91_add_device_i2c(NULL, 0);
/* NAND */
- at91_add_device_nand(&ek_nand_data);
+ ek_add_device_nand();
/* DM9000 ethernet */
ek_add_device_dm9000();