diff options
Diffstat (limited to 'Documentation')
| -rw-r--r-- | Documentation/isdn/HiSax.cert | 96 | ||||
| -rw-r--r-- | Documentation/isdn/README.HiSax | 659 |
2 files changed, 0 insertions, 755 deletions
diff --git a/Documentation/isdn/HiSax.cert b/Documentation/isdn/HiSax.cert deleted file mode 100644 index f2a6fcb8efee..000000000000 --- a/Documentation/isdn/HiSax.cert +++ /dev/null @@ -1,96 +0,0 @@ ------BEGIN PGP SIGNED MESSAGE----- - -First: - - HiSax is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - -However, if you wish to modify the HiSax sources, please note the following: - -HiSax has passed the ITU approval test suite with ELSA Quickstep ISDN cards -and Eicon Technology Diva 2.01 PCI card. -The certification is only valid for the combination of the tested software -version and the tested hardware. Any changes to the HiSax source code may -therefore affect the certification. - -Additional ITU approval tests have been carried out for all generic cards -using Colognechip single chip solutions HFC-S PCI A for PCI cards as well -as HFC-S USB based USB ISDN ta adapters. -These tests included all layers 1-3 and as well all functional tests for -the layer 1. Because all hardware based on these chips are complete ISDN -solutions in one chip all cards and USB-TAs using these chips are to be -regarded as approved for those tests. Some additional electrical tests -of the layer 1 which are independent of the driver and related to a -special hardware used will be regarded as approved if at least one -solution has been tested including those electrical tests. So if cards -or tas have been completely approved for any other os, the approval -for those electrical tests is valid for linux, too. -Please send any questions regarding this drivers or approval abouts to -werner@isdn-development.de -Additional information and the type approval documents will be found -shortly on the Colognechip website www.colognechip.com - -If you change the main files of the HiSax ISDN stack, the certification will -become invalid. Because in most countries it is illegal to connect -unapproved ISDN equipment to the public network, I have to guarantee that -changes in HiSax do not affect the certification. - -In order to make a valid certification apparent to the user, I have built in -some validation checks that are made during the make process. The HiSax main -files are protected by md5 checksums and the md5sum file is pgp signed by -myself: - -KeyID 1024/FF992F6D 1997/01/16 Karsten Keil <kkeil@suse.de> -Key fingerprint = 92 6B F7 58 EE 86 28 C8 C4 1A E6 DC 39 89 F2 AA - -Only if the checksums are OK, and the signature of the file -"drivers/isdn/hisax/md5sums.asc" match, is the certification valid; a -message confirming this is then displayed during the hisax init process. - -The affected files are: - -drivers/isdn/hisax/isac.c -drivers/isdn/hisax/isdnl1.c -drivers/isdn/hisax/isdnl2.c -drivers/isdn/hisax/isdnl3.c -drivers/isdn/hisax/tei.c -drivers/isdn/hisax/callc.c -drivers/isdn/hisax/l3dss1.c -drivers/isdn/hisax/l3_1tr6.c -drivers/isdn/hisax/cert.c -drivers/isdn/hisax/elsa.c -drivers/isdn/hisax/diva.c -drivers/isdn/hisax/hfc_pci.c - -Please send any changes, bugfixes and patches to me rather than implementing -them directly into the HiSax sources. - -This does not reduce your rights granted by the GNU General Public License. -If you wish to change the sources, go ahead; but note that then the -certification is invalid even if you use one of the approved cards. - -Here are the certification registration numbers for ELSA Quickstep cards: -German D133361J CETECOM ICT Services GmbH 0682 -European D133362J CETECOM ICT Services GmbH 0682 - - -Karsten Keil -keil@isdn4linux.de - ------BEGIN PGP SIGNATURE----- -Version: 2.6.3i -Charset: noconv - -iQCVAwUBOFAwqTpxHvX/mS9tAQFI2QP9GLDK2iy/KBhwReE3F7LeO+tVhffTVZ3a -20q5/z/WcIg/pnH0uTkl2UgDXBFXYl45zJyDGNpAposIFmT+Edd14o7Vj1w/BBdn -Y+5rBmJf+gyBu61da5d6bv0lpymwRa/um+ri+ilYnZ/XPfg5JKhdjGSBCJuJAElM -d2jFbTrsMYw= -=LNf9 ------END PGP SIGNATURE----- diff --git a/Documentation/isdn/README.HiSax b/Documentation/isdn/README.HiSax deleted file mode 100644 index b1a573cf4472..000000000000 --- a/Documentation/isdn/README.HiSax +++ /dev/null @@ -1,659 +0,0 @@ -HiSax is a Linux hardware-level driver for passive ISDN cards with Siemens -chipset (ISAC_S 2085/2086/2186, HSCX SAB 82525). It is based on the Teles -driver from Jan den Ouden. -It is meant to be used with isdn4linux, an ISDN link-level module for Linux -written by Fritz Elfert. - - This program is free software; you can redistribute it and/or modify - it under the terms of the GNU General Public License as published by - the Free Software Foundation; either version 2 of the License, or - (at your option) any later version. - - This program is distributed in the hope that it will be useful, - but WITHOUT ANY WARRANTY; without even the implied warranty of - MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the - GNU General Public License for more details. - - You should have received a copy of the GNU General Public License - along with this program; if not, write to the Free Software - Foundation, Inc., 675 Mass Ave, Cambridge, MA 02139, USA. - - -Supported cards ---------------- - -Teles 8.0/16.0/16.3 and compatible ones -Teles 16.3c -Teles S0/PCMCIA -Teles PCI -Teles S0Box -Creatix S0Box -Creatix PnP S0 -Compaq ISDN S0 ISA card -AVM A1 (Fritz, Teledat 150) -AVM Fritz PCMCIA -AVM Fritz PnP -AVM Fritz PCI -ELSA Microlink PCC-16, PCF, PCF-Pro, PCC-8 -ELSA Quickstep 1000 -ELSA Quickstep 1000PCI -ELSA Quickstep 3000 (same settings as QS1000) -ELSA Quickstep 3000PCI -ELSA PCMCIA -ITK ix1-micro Rev.2 -Eicon Diva 2.0 ISA and PCI (S0 and U interface, no PRO version) -Eicon Diva 2.01 ISA and PCI -Eicon Diva 2.02 PCI -Eicon Diva Piccola -ASUSCOM NETWORK INC. ISDNLink 128K PC adapter (order code I-IN100-ST-D) -Dynalink IS64PH (OEM version of ASUSCOM NETWORK INC. ISDNLink 128K adapter) -PCBIT-DP (OEM version of ASUSCOM NETWORK INC. ISDNLink) -HFC-2BS0 based cards (TeleInt SA1) -Sedlbauer Speed Card (Speed Win, Teledat 100, PCI, Fax+) -Sedlbauer Speed Star/Speed Star2 (PCMCIA) -Sedlbauer ISDN-Controller PC/104 -USR Sportster internal TA (compatible Stollmann tina-pp V3) -USR internal TA PCI -ith Kommunikationstechnik GmbH MIC 16 ISA card -Traverse Technologie NETjet PCI S0 card and NETspider U card -Ovislink ISDN sc100-p card (NETjet driver) -Dr. Neuhaus Niccy PnP/PCI -Siemens I-Surf 1.0 -Siemens I-Surf 2.0 (with IPAC, try type 12 asuscom) -ACER P10 -HST Saphir -Berkom Telekom A4T -Scitel Quadro -Gazel ISDN cards -HFC-PCI based cards -Winbond W6692 based cards -HFC-S+, HFC-SP/PCMCIA cards -formula-n enternow -Gerdes Power ISDN - -Note: PCF, PCF-Pro: up to now, only the ISDN part is supported - PCC-8: not tested yet - Eicon.Diehl Diva U interface not tested - -If you know other passive cards with the Siemens chipset, please let me know. -You can combine any card, if there is no conflict between the resources -(io, mem, irq). - - -Configuring the driver ----------------------- - -The HiSax driver can either be built directly into the kernel or as a module. -It can be configured using the command line feature while loading the kernel -with LILO or LOADLIN or, if built as a module, using insmod/modprobe with -parameters. -There is also some config needed before you compile the kernel and/or -modules. It is included in the normal "make [menu]config" target at the -kernel. Don't forget it, especially to select the right D-channel protocol. - -Please note: In older versions of the HiSax driver, all PnP cards -needed to be configured with isapnp and worked only with the HiSax -driver used as a module. - -In the current version, HiSax will automatically use the in-kernel -ISAPnP support, provided you selected it during kernel configuration -(CONFIG_ISAPNP), if you don't give the io=, irq= command line parameters. - -The affected card types are: 4,7,12,14,19,27-30 - -a) when built as a module -------------------------- - -insmod/modprobe hisax.o \ - io=iobase irq=IRQ mem=membase type=card_type \ - protocol=D_channel_protocol id=idstring - -or, if several cards are installed: - -insmod/modprobe hisax.o \ - io=iobase1,iobase2,... irq=IRQ1,IRQ2,... mem=membase1,membase2,... \ - type=card_type1,card_type2,... \ - protocol=D_channel_protocol1,D_channel_protocol2,... \ - id=idstring1%idstring2 ... - -where "iobaseN" represents the I/O base address of the Nth card, "membaseN" -the memory base address of the Nth card, etc. - -The reason for the delimiter "%" being used in the idstrings is that "," -won't work with the current modules package. - -The parameters may be specified in any order. For example, the "io" -parameter may precede the "irq" parameter, or vice versa. If several -cards are installed, the ordering within the comma separated parameter -lists must of course be consistent. - -Only parameters applicable to the card type need to be specified. For -example, the Teles 16.3 card is not memory-mapped, so the "mem" -parameter may be omitted for this card. Sometimes it may be necessary -to specify a dummy parameter, however. This is the case when there is -a card of a different type later in the list that needs a parameter -which the preceding card does not. For instance, if a Teles 16.0 card -is listed after a Teles 16.3 card, a dummy memory base parameter of 0 -must be specified for the 16.3. Instead of a dummy value, the parameter -can also be skipped by simply omitting the value. For example: -mem=,0xd0000. See example 6 below. - -The parameter for the D-Channel protocol may be omitted if you selected the -correct one during kernel config. Valid values are "1" for German 1TR6, -"2" for EDSS1 (Euro ISDN), "3" for leased lines (no D-Channel) and "4" -for US NI1. -With US NI1 you have to include your SPID into the MSN setting in the form -<MSN>:<SPID> for example (your phonenumber is 1234 your SPID 5678): -AT&E1234:5678 on ttyI interfaces -isdnctrl eaz ippp0 1234:5678 on network devices - -The Creatix/Teles PnP cards use io1= and io2= instead of io= for specifying -the I/O addresses of the ISAC and HSCX chips, respectively. - -Card types: - - Type Required parameters (in addition to type and protocol) - - 1 Teles 16.0 irq, mem, io - 2 Teles 8.0 irq, mem - 3 Teles 16.3 (non PnP) irq, io - 4 Creatix/Teles PnP irq, io0 (ISAC), io1 (HSCX) - 5 AVM A1 (Fritz) irq, io - 6 ELSA PCC/PCF cards io or nothing for autodetect (the iobase is - required only if you have more than one ELSA - card in your PC) - 7 ELSA Quickstep 1000 irq, io (from isapnp setup) - 8 Teles 16.3 PCMCIA irq, io - 9 ITK ix1-micro Rev.2 irq, io - 10 ELSA PCMCIA irq, io (set with card manager) - 11 Eicon.Diehl Diva ISA PnP irq, io - 11 Eicon.Diehl Diva PCI no parameter - 12 ASUS COM ISDNLink irq, io (from isapnp setup) - 13 HFC-2BS0 based cards irq, io - 14 Teles 16.3c PnP irq, io - 15 Sedlbauer Speed Card irq, io - 15 Sedlbauer PC/104 irq, io - 15 Sedlbauer Speed PCI no parameter - 16 USR Sportster internal irq, io - 17 MIC card irq, io - 18 ELSA Quickstep 1000PCI no parameter - 19 Compaq ISDN S0 ISA card irq, io0, io1, io (from isapnp setup io=IO2) - 20 NETjet PCI card no parameter - 21 Teles PCI no parameter - 22 Sedlbauer Speed Star (PCMCIA) irq, io (set with card manager) - 24 Dr. Neuhaus Niccy PnP irq, io0, io1 (from isapnp setup) - 24 Dr. Neuhaus Niccy PCI no parameter - 25 Teles S0Box irq, io (of the used lpt port) - 26 AVM A1 PCMCIA (Fritz!) irq, io (set with card manager) - 27 AVM PnP (Fritz!PnP) irq, io (from isapnp setup) - 27 AVM PCI (Fritz!PCI) no parameter - 28 Sedlbauer Speed Fax+ irq, io (from isapnp setup) - 29 Siemens I-Surf 1.0 irq, io, memory (from isapnp setup) - 30 ACER P10 irq, io (from isapnp setup) - 31 HST Saphir irq, io - 32 Telekom A4T none - 33 Scitel Quadro subcontroller (4*S0, subctrl 1...4) - 34 Gazel ISDN cards (ISA) irq,io - 34 Gazel ISDN cards (PCI) none - 35 HFC 2BDS0 PCI none - 36 W6692 based PCI cards none - 37 HFC 2BDS0 S+, SP irq,io - 38 NETspider U PCI card none - 39 HFC 2BDS0 SP/PCMCIA irq,io (set with cardmgr) - 40 hotplug interface - 41 Formula-n enter:now PCI none - -At the moment IRQ sharing is only possible with PCI cards. Please make sure -that your IRQ is free and enabled for ISA use. - - -Examples for module loading - -1. Teles 16.3, Euro ISDN, I/O base 280 hex, IRQ 10 - modprobe hisax type=3 protocol=2 io=0x280 irq=10 - -2. Teles 16.0, 1TR6 ISDN, I/O base d80 hex, IRQ 5, Memory d0000 hex - modprobe hisax protocol=1 type=1 io=0xd80 mem=0xd0000 irq=5 - -3. Fritzcard, Euro ISDN, I/O base 340 hex, IRQ 10 and ELSA PCF, Euro ISDN - modprobe hisax type=5,6 protocol=2,2 io=0x340 irq=10 id=Fritz%Elsa - -4. Any ELSA PCC/PCF card, Euro ISDN - modprobe hisax type=6 protocol=2 - -5. Teles 16.3 PnP, Euro ISDN, with isapnp configured - isapnp config: (INT 0 (IRQ 10 (MODE +E))) - (IO 0 (BASE 0x0580)) - (IO 1 (BASE 0x0180)) - modprobe hisax type=4 protocol=2 irq=10 io0=0x580 io1=0x180 - - In the current version of HiSax, you can instead simply use - - modprobe hisax type=4 protocol=2 - - if you configured your kernel for ISAPnP. Don't run isapnp in - this case! - -6. Teles 16.3, Euro ISDN, I/O base 280 hex, IRQ 12 and - Teles 16.0, 1TR6, IRQ 5, Memory d0000 hex - modprobe hisax type=3,1 protocol=2,1 io=0x280 mem=0,0xd0000 - - Please note the dummy 0 memory address for the Teles 16.3, used as a - placeholder as described above, in the last example. - -7. Teles PCMCIA, Euro ISDN, I/O base 180 hex, IRQ 15 (default values) - modprobe hisax type=8 protocol=2 io=0x180 irq=15 - - -b) using LILO/LOADLIN, with the driver compiled directly into the kernel ------------------------------------------------------------------------- - -hisax=typ1,dp1,pa_1,pb_1,pc_1[,typ2,dp2,pa_2 ... \ - typn,dpn,pa_n,pb_n,pc_n][,idstring1[,idstring2,...,idstringn]] - -where - typ1 = type of 1st card (default depends on kernel settings) - dp1 = D-Channel protocol of 1st card. 1=1TR6, 2=EDSS1, 3=leased - pa_1 = 1st parameter (depending on the type of the card) - pb_1 = 2nd parameter ( " " " " " " " ) - pc_1 = 3rd parameter ( " " " " " " " ) - - typ2,dp2,pa_2,pb_2,pc_2 = Parameters of the second card (defaults: none) - typn,dpn,pa_n,pb_n,pc_n = Parameters of the n'th card (up to 16 cards are - supported) - - idstring = Driver ID for accessing the particular card with utility - programs and for identification when using a line monitor - (default: "HiSax") - - Note: the ID string must start with an alphabetical character! - -Card types: - -type - 1 Teles 16.0 pa=irq pb=membase pc=iobase - 2 Teles 8.0 pa=irq pb=membase - 3 Teles 16.3 pa=irq pb=iobase - 4 Creatix/Teles PNP ONLY WORKS AS A MODULE ! - 5 AVM A1 (Fritz) pa=irq pb=iobase - 6 ELSA PCC/PCF cards pa=iobase or nothing for autodetect - 7 ELSA Quickstep 1000 ONLY WORKS AS A MODULE ! - 8 Teles S0 PCMCIA pa=irq pb=iobase - 9 ITK ix1-micro Rev.2 pa=irq pb=iobase - 10 ELSA PCMCIA pa=irq, pb=io (set with card manager) - 11 Eicon.Diehl Diva ISAPnP ONLY WORKS AS A MODULE ! - 11 Eicon.Diehl Diva PCI no parameter - 12 ASUS COM ISDNLink ONLY WORKS AS A MODULE ! - 13 HFC-2BS0 based cards pa=irq pb=io - 14 Teles 16.3c PnP ONLY WORKS AS A MODULE ! - 15 Sedlbauer Speed Card pa=irq pb=io (Speed Win only as module !) - 15 Sedlbauer PC/104 pa=irq pb=io - 15 Sedlbauer Speed PCI no parameter - 16 USR Sportster internal pa=irq pb=io - 17 MIC card pa=irq pb=io - 18 ELSA Quickstep 1000PCI no parameter - 19 Compaq ISDN S0 ISA card ONLY WORKS AS A MODULE ! - 20 NETjet PCI card no parameter - 21 Teles PCI no parameter - 22 Sedlbauer Speed Star (PCMCIA) pa=irq, pb=io (set with card manager) - 24 Dr. Neuhaus Niccy PnP ONLY WORKS AS A MODULE ! - 24 Dr. Neuhaus Niccy PCI no parameter - 25 Teles S0Box pa=irq, pb=io (of the used lpt port) - 26 AVM A1 PCMCIA (Fritz!) pa=irq, pb=io (set with card manager) - 27 AVM PnP (Fritz!PnP) ONLY WORKS AS A MODULE ! - 27 AVM PCI (Fritz!PCI) no parameter - 28 Sedlbauer Speed Fax+ ONLY WORKS AS A MODULE ! - 29 Siemens I-Surf 1.0 ONLY WORKS AS A MODULE ! - 30 ACER P10 ONLY WORKS AS A MODULE ! - 31 HST Saphir pa=irq, pb=io - 32 Telekom A4T no parameter - 33 Scitel Quadro subcontroller (4*S0, subctrl 1...4) - 34 Gazel ISDN cards (ISA) pa=irq, pb=io - 34 Gazel ISDN cards (PCI) no parameter - 35 HFC 2BDS0 PCI no parameter - 36 W6692 based PCI cards none - 37 HFC 2BDS0 S+,SP/PCMCIA ONLY WORKS AS A MODULE ! - 38 NETspider U PCI card none - 39 HFC 2BDS0 SP/PCMCIA ONLY WORKS AS A MODULE ! - 40 hotplug interface ONLY WORKS AS A MODULE ! - 41 Formula-n enter:now PCI none - -Running the driver ------------------- - -When you insmod isdn.o and hisax.o (or with the in-kernel version, during -boot time), a few lines should appear in your syslog. Look for something like: - -Apr 13 21:01:59 kke01 kernel: HiSax: Driver for Siemens chip set ISDN cards -Apr 13 21:01:59 kke01 kernel: HiSax: Version 2.9 -Apr 13 21:01:59 kke01 kernel: HiSax: Revisions 1.14/1.9/1.10/1.25/1.8 -Apr 13 21:01:59 kke01 kernel: HiSax: Total 1 card defined -Apr 13 21:01:59 kke01 kernel: HiSax: Card 1 Protocol EDSS1 Id=HiSax1 (0) -Apr 13 21:01:59 kke01 kernel: HiSax: Elsa driver Rev. 1.13 -... -Apr 13 21:01:59 kke01 kernel: Elsa: PCF-Pro found at 0x360 Rev.:C IRQ 10 -Apr 13 21:01:59 kke01 kernel: Elsa: timer OK; resetting card -Apr 13 21:01:59 kke01 kernel: Elsa: HSCX version A: V2.1 B: V2.1 -Apr 13 21:01:59 kke01 kernel: Elsa: ISAC 2086/2186 V1.1 -... -Apr 13 21:01:59 kke01 kernel: HiSax: DSS1 Rev. 1.14 -Apr 13 21:01:59 kke01 kernel: HiSax: 2 channels added - -This means that the card is ready for use. -Cabling problems or line-downs are not detected, and only some ELSA cards can -detect the S0 power. - -Remember that, according to the new strategy for accessing low-level drivers -from within isdn4linux, you should also define a driver ID while doing -insmod: Simply append hisax_id=<SomeString> to the insmod command line. This -string MUST NOT start with a digit or a small 'x'! - -At this point you can run a 'cat /dev/isdnctrl0' and view debugging messages. - -At the moment, debugging messages are enabled with the hisaxctrl tool: - - hisaxctrl <DriverId> DebugCmd <debugging_flags> - -<DriverId> default is HiSax, if you didn't specify one. - -DebugCmd is 1 for generic debugging - 11 for layer 1 development debugging - 13 for layer 3 development debugging - -where <debugging_flags> is the integer sum of the following debugging -options you wish enabled: - -With DebugCmd set to 1: - - 0x0001 Link-level <--> hardware-level communication - 0x0002 Top state machine - 0x0004 D-Channel Frames for isdnlog - 0x0008 D-Channel Q.921 - 0x0010 B-Channel X.75 - 0x0020 D-Channel l2 - 0x0040 B-Channel l2 - 0x0080 D-Channel link state debugging - 0x0100 B-Channel link state debugging - 0x0200 TEI debug - 0x0400 LOCK debug in callc.c - 0x0800 More paranoid debug in callc.c (not for normal use) - 0x1000 D-Channel l1 state debugging - 0x2000 B-Channel l1 state debugging - -With DebugCmd set to 11: - - 0x0001 Warnings (default: on) - 0x0002 IRQ status - 0x0004 ISAC - 0x0008 ISAC FIFO - 0x0010 HSCX - 0x0020 HSCX FIFO (attention: full B-Channel output!) - 0x0040 D-Channel LAPD frame types - 0x0080 IPAC debug - 0x0100 HFC receive debug - 0x0200 ISAC monitor debug - 0x0400 D-Channel frames for isdnlog (set with 1 0x4 too) - 0x0800 D-Channel message verbose - -With DebugCmd set to 13: - - 1 Warnings (default: on) - 2 l3 protocol descriptor errors - 4 l3 state machine - 8 charge info debugging (1TR6) - -For example, 'hisaxctrl HiSax 1 0x3ff' enables full generic debugging. - -Because of some obscure problems with some switch equipment, the delay -between the CONNECT message and sending the first data on the B-channel is now -configurable with - -hisaxctrl <DriverId> 2 <delay> -<delay> in ms Value between 50 and 800 ms is recommended. - -Downloading Firmware --------------------- -At the moment, the Sedlbauer speed fax+ is the only card, which -needs to download firmware. -The firmware is downloaded with the hisaxctrl tool: - - hisaxctrl <DriverId> 9 <firmware_filename> - -<DriverId> default is HiSax, if you didn't specify one, - -where <firmware_filename> is the filename of the firmware file. - -For example, 'hisaxctrl HiSax 9 ISAR.BIN' downloads the firmware for -ISAR based cards (like the Sedlbauer speed fax+). - -Warning -------- -HiSax is a work in progress and may crash your machine. -For certification look at HiSax.cert file. - -Limitations ------------ -At this time, HiSax only works on Euro ISDN lines and German 1TR6 lines. -For leased lines see appendix. - -Bugs ----- -If you find any, please let me know. - - -Thanks ------- -Special thanks to: - - Emil Stephan for the name HiSax which is a mix of HSCX and ISAC. - - Fritz Elfert, Jan den Ouden, Michael Hipp, Michael Wein, - Andreas Kool, Pekka Sarnila, Sim Yskes, Johan Myrre'en, - Klaus-Peter Nischke (ITK AG), Christof Petig, Werner Fehn (ELSA GmbH), - Volker Schmidt - Edgar Toernig and Marcus Niemann for the Sedlbauer driver - Stephan von Krawczynski - Juergen Quade for the Leased Line part - Klaus Lichtenwalder (Klaus.Lichtenwalder@WebForum.DE), for ELSA PCMCIA support - Enrik Berkhan (enrik@starfleet.inka.de) for S0BOX specific stuff - Ton van Rosmalen for Teles PCI - Petr Novak <petr.novak@i.cz> for Winbond W6692 support - Werner Cornelius <werner@isdn4linux.de> for HFC-PCI, HFC-S(+/P) and supplementary services support - and more people who are hunting bugs. (If I forgot somebody, please - send me a mail). - - Firma ELSA GmbH - Firma Eicon.Diehl GmbH - Firma Dynalink NL - Firma ASUSCOM NETWORK INC. Taiwan - Firma S.u.S.E - Firma ith Kommunikationstechnik GmbH - Firma Traverse Technologie Australia - Firma Medusa GmbH (www.medusa.de). - Firma Quant-X Austria for sponsoring a DEC Alpha board+CPU - Firma Cologne Chip Designs GmbH - - My girl friend and partner in life Ute for her patience with me. - - -Enjoy, - -Karsten Keil -keil@isdn4linux.de - - -Appendix: Teles PCMCIA driver ------------------------------ - -See - http://www.linux.no/teles_cs.txt -for instructions. - -Appendix: Linux and ISDN-leased lines -------------------------------------- - -Original from Juergen Quade, new version KKe. - -Attention NEW VERSION, the old leased line syntax won't work !!! - -You can use HiSax to connect your Linux-Box via an ISDN leased line -to e.g. the Internet: - -1. Build a kernel which includes the HiSax driver either as a module - or as part of the kernel. - cd /usr/src/linux - make menuconfig - <ISDN subsystem - ISDN support -- HiSax> - make clean; make zImage; make modules; make modules_install -2. Install the new kernel - cp /usr/src/linux/arch/x86/boot/zImage /etc/kernel/linux.isdn - vi /etc/lilo.conf - <add new kernel in the bootable image section> - lilo -3. in case the hisax driver is a "fixed" part of the kernel, configure - the driver with lilo: - vi /etc/lilo.conf - <add HiSax driver parameter in the global section (see below)> - lilo - Your lilo.conf _might_ look like the following: - - # LILO configuration-file - # global section - # teles 16.0 on IRQ=5, MEM=0xd8000, PORT=0xd80 - append="hisax=1,3,5,0xd8000,0xd80,HiSax" - # teles 16.3 (non pnp) on IRQ=15, PORT=0xd80 - # append="hisax=3,3,5,0xd8000,0xd80,HiSax" - boot=/dev/sda - compact # faster, but won't work on all systems. - linear - read-only - prompt - timeout=100 - vga = normal # force sane state - # Linux bootable partition config begins - image = /etc/kernel/linux.isdn - root = /dev/sda1 - label = linux.isdn - # - image = /etc/kernel/linux-2.0.30 - root = /dev/sda1 - label = linux.secure - - In the line starting with "append" you have to adapt the parameters - according to your card (see above in this file) - -3. boot the new linux.isdn kernel -4. start the ISDN subsystem: - a) load - if necessary - the modules (depends, whether you compiled - the ISDN driver as module or not) - According to the type of card you have to specify the necessary - driver parameter (irq, io, mem, type, protocol). - For the leased line the protocol is "3". See the table above for - the parameters, which you have to specify depending on your card. - b) configure i4l - /sbin/isdnctrl addif isdn0 - # EAZ 1 -- B1 channel 2 --B2 channel - /sbin/isdnctrl eaz isdn0 1 - /sbin/isdnctrl secure isdn0 on - /sbin/isdnctrl huptimeout isdn0 0 - /sbin/isdnctrl l2_prot isdn0 hdlc - # Attention you must not set an outgoing number !!! This won't work !!! - # The incoming number is LEASED0 for the first card, LEASED1 for the - # second and so on. - /sbin/isdnctrl addphone isdn0 in LEASED0 - # Here is no need to bind the channel. - c) in case the remote partner is a CISCO: - /sbin/isdnctrl encap isdn0 cisco-h - d) configure the interface - /sbin/ifconfig isdn0 ${LOCAL_IP} pointopoint ${REMOTE_IP} - e) set the routes - /sbin/route add -host ${REMOTE_IP} isdn0 - /sbin/route add default gw ${REMOTE_IP} - f) switch the card into leased mode for each used B-channel - /sbin/hisaxctrl HiSax 5 1 - -Remarks: -a) Use state of the art isdn4k-utils - -Here an example script: -#!/bin/sh -# Start/Stop ISDN leased line connection - -I4L_AS_MODULE=yes -I4L_REMOTE_IS_CISCO=no -I4L_MODULE_PARAMS="type=16 io=0x268 irq=7 " -I4L_DEBUG=no -I4L_LEASED_128K=yes -LOCAL_IP=192.168.1.1 -REMOTE_IP=192.168.2.1 - -case "$1" in - start) - echo "Starting ISDN ..." - if [ ${I4L_AS_MODULE} = "yes" ]; then - echo "loading modules..." - /sbin/modprobe hisax ${I4L_MODULE_PARAMS} - fi - # configure interface - /sbin/isdnctrl addif isdn0 - /sbin/isdnctrl secure isdn0 on - if [ ${I4L_DEBUG} = "yes" ]; then - /sbin/isdnctrl verbose 7 - /sbin/hisaxctrl HiSax 1 0xffff - /sbin/hisaxctrl HiSax 11 0xff - cat /dev/isdnctrl >/tmp/lea.log & - fi - if [ ${I4L_REMOTE_IS_CISCO} = "yes" ]; then - /sbin/isdnctrl encap isdn0 cisco-h - fi - /sbin/isdnctrl huptimeout isdn0 0 - # B-CHANNEL 1 - /sbin/isdnctrl eaz isdn0 1 - /sbin/isdnctrl l2_prot isdn0 hdlc - # 1. card - /sbin/isdnctrl addphone isdn0 in LEASED0 - if [ ${I4L_LEASED_128K} = "yes" ]; then - /sbin/isdnctrl addslave isdn0 isdn0s - /sbin/isdnctrl secure isdn0s on - /sbin/isdnctrl huptimeout isdn0s 0 - # B-CHANNEL 2 - /sbin/isdnctrl eaz isdn0s 2 - /sbin/isdnctrl l2_prot isdn0s hdlc - # 1. card - /sbin/isdnctrl addphone isdn0s in LEASED0 - if [ ${I4L_REMOTE_IS_CISCO} = "yes" ]; then - /sbin/isdnctrl encap isdn0s cisco-h - fi - fi - /sbin/isdnctrl dialmode isdn0 manual - # configure tcp/ip - /sbin/ifconfig isdn0 ${LOCAL_IP} pointopoint ${REMOTE_IP} - /sbin/route add -host ${REMOTE_IP} isdn0 - /sbin/route add default gw ${REMOTE_IP} - # switch to leased mode - # B-CHANNEL 1 - /sbin/hisaxctrl HiSax 5 1 - if [ ${I4L_LEASED_128K} = "yes" ]; then - # B-CHANNEL 2 - sleep 10; /* Wait for master */ - /sbin/hisaxctrl HiSax 5 2 - fi - ;; - stop) - /sbin/ifconfig isdn0 down - /sbin/isdnctrl delif isdn0 - if [ ${I4L_DEBUG} = "yes" ]; then - killall cat - fi - if [ ${I4L_AS_MODULE} = "yes" ]; then - /sbin/rmmod hisax - /sbin/rmmod isdn - /sbin/rmmod ppp - /sbin/rmmod slhc - fi - ;; - *) - echo "Usage: $0 {start|stop}" - exit 1 -esac -exit 0 |