1 files changed, 0 insertions, 83 deletions
diff --git a/Documentation/scsi/dpti.txt b/Documentation/scsi/dpti.txt
deleted file mode 100644
index f36dc0e7c8da..000000000000
--- a/Documentation/scsi/dpti.txt
+++ /dev/null
@@ -1,83 +0,0 @@
- /* TERMS AND CONDITIONS OF USE
- * 
- * Redistribution and use in source form, with or without modification, are
- * permitted provided that redistributions of source code must retain the
- * above copyright notice, this list of conditions and the following disclaimer.
- * 
- * This software is provided `as is' by Adaptec and
- * any express or implied warranties, including, but not limited to, the
- * implied warranties of merchantability and fitness for a particular purpose,
- * are disclaimed. In no event shall Adaptec be
- * liable for any direct, indirect, incidental, special, exemplary or
- * consequential damages (including, but not limited to, procurement of
- * substitute goods or services; loss of use, data, or profits; or business
- * interruptions) however caused and on any theory of liability, whether in
- * contract, strict liability, or tort (including negligence or otherwise)
- * arising in any way out of the use of this driver software, even if advised
- * of the possibility of such damage.
- * 
- ****************************************************************
- * This driver supports the Adaptec I2O RAID and DPT SmartRAID V I2O boards.
- *
- * CREDITS:
- * The original linux driver was ported to Linux by Karen White while at 
- * Dell Computer.  It was ported from Bob Pasteur's (of DPT) original 
- * non-Linux driver.  Mark Salyzyn and Bob Pasteur consulted on the original
- * driver. 
- * 
- * 2.0 version of the driver by Deanna Bonds and Mark Salyzyn.
- *
- * HISTORY:
- * The driver was originally ported to linux version 2.0.34 
- *
- * V2.0 Rewrite of driver.  Re-architectured based on i2o subsystem.
- *   This was the first full GPL version since the last version used
- *   i2osig headers which were not GPL.  Developer Testing version.
- * V2.1 Internal testing
- * V2.2 First released version
- *
- * V2.3 
- *   Changes:
- *      Added Raptor Support
- *      Fixed bug causing system to hang under extreme load with 
- *         management utilities running (removed GFP_DMA from kmalloc flags)
- *
- *
- * V2.4 First version ready to be submitted to be embedded in the kernel
- *   Changes: 
- *      Implemented suggestions from Alan Cox
- *      Added calculation of resid for sg layer
- *      Better error handling
- *         Added checking underflow conditions 
- *         Added DATAPROTECT checking
- *         Changed error return codes
- *         Fixed pointer bug in bus reset routine
- *      Enabled hba reset from ioctls (allows a FW flash to reboot and use the new
- *         FW without having to reboot)
- *      Changed proc output
- *
- * TODO:
- *      Add 64 bit Scatter Gather when compiled on 64 bit architectures
- *      Add sparse lun scanning 
- *      Add code that checks if a device that had been taken offline is
- *         now online (at the FW level) when test unit ready or inquiry 
- *         command from scsi-core
- *      Add proc read interface
- *         busrescan command
- *         rescan command
- *      Add code to rescan routine that notifies scsi-core about new devices
- *      Add support for C-PCI (hotplug stuff)
- *      Add ioctl passthru error recovery
- *
- * NOTES:
- * The DPT card optimizes the order of processing commands.  Consequently,
- * a command may take up to 6 minutes to complete after it has been sent
- * to the board.  
- *
- * The files dpti_ioctl.h dptsig.h osd_defs.h osd_util.h sys_info.h are part of the
- * interface files for Adaptec's management routines.  These define the structures used
- * in the ioctls.  They are written to be portable.  They are hard to read, but I need
- * to use them 'as is' or I can miss changes in the interface.
- *
- */
-