diff options
Diffstat (limited to 'Documentation/devicetree/bindings/mmc/arm,pl18x.yaml')
| -rw-r--r-- | Documentation/devicetree/bindings/mmc/arm,pl18x.yaml | 203 |
1 files changed, 203 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml b/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml new file mode 100644 index 000000000000..eddc1f6bdbe5 --- /dev/null +++ b/Documentation/devicetree/bindings/mmc/arm,pl18x.yaml @@ -0,0 +1,203 @@ +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause) +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/mmc/arm,pl18x.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: ARM PrimeCell MultiMedia Card Interface (MMCI) PL180 and PL181 + +maintainers: + - Linus Walleij <linus.walleij@linaro.org> + - Ulf Hansson <ulf.hansson@linaro.org> + +description: + The ARM PrimeCells MMCI PL180 and PL181 provides an interface for + reading and writing to MultiMedia and SD cards alike. Over the years + vendors have use the VHDL code from ARM to create derivative MMC/SD/SDIO + host controllers with very similar characteristics. + +allOf: + - $ref: /schemas/arm/primecell.yaml# + - $ref: mmc-controller.yaml# + +# We need a select here so we don't match all nodes with 'arm,primecell' +select: + properties: + compatible: + contains: + enum: + - arm,pl180 + - arm,pl181 + - arm,pl18x + required: + - compatible + +properties: + compatible: + oneOf: + - description: The first version of the block, simply called + PL180 and found in the ARM Integrator IM/PD1 logic module. + items: + - const: arm,pl180 + - const: arm,primecell + - description: The improved version of the block, found in the + ARM Versatile and later reference designs. Further revisions + exist but get detected at runtime by reading some magic numbers + in the PrimeCell ID registers. + items: + - const: arm,pl181 + - const: arm,primecell + - description: Wildcard entry that will let the operating system + inspect the PrimeCell ID registers to determine which hardware + variant of PL180 or PL181 this is. + items: + - const: arm,pl18x + - const: arm,primecell + + clocks: + description: One or two clocks, the "apb_pclk" and the "MCLK" + which is the core block clock. The names are not compulsory. + minItems: 1 + maxItems: 2 + + power-domains: true + + resets: + maxItems: 1 + + reg: + description: the MMIO memory window must be exactly 4KB (0x1000) and the + layout should provide the PrimeCell ID registers so that the device can + be discovered. On ST Micro variants, a second register window may be + defined if a delay block is present and used for tuning. + + interrupts: + description: The first interrupt is the command interrupt and corresponds + to the event at the end of a command. The second interrupt is the + PIO (polled I/O) interrupt and occurs when the FIFO needs to be + emptied as part of a bulk read from the card. Some variants have these + two interrupts wired into the same line (logic OR) and in that case + only one interrupt may be provided. + minItems: 1 + maxItems: 2 + + st,sig-dir-dat0: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, bus signal direction pins used for + DAT[0]. + + st,sig-dir-dat2: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, bus signal direction pins used for + DAT[2]. + + st,sig-dir-dat31: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, bus signal direction pins used for + DAT[3] and DAT[1]. + + st,sig-dir-dat74: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, bus signal direction pins used for + DAT[7] and DAT[4]. + + st,sig-dir-cmd: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, CMD signal direction used for + pin CMD. + + st,sig-pin-fbclk: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, feedback clock FBCLK signal pin + in use. + + st,sig-dir: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, signal direction polarity used for + pins CMD, DAT[0], DAT[1], DAT[2] and DAT[3]. + + st,neg-edge: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, data and command phase relation, + generated on the sd clock falling edge. + + st,use-ckin: + $ref: /schemas/types.yaml#/definitions/flag + description: ST Micro-specific property, use CKIN pin from an external + driver to sample the receive data (for example with a voltage switch + transceiver). + +unevaluatedProperties: false + +required: + - compatible + - reg + - interrupts + +examples: + - | + #include <dt-bindings/interrupt-controller/irq.h> + #include <dt-bindings/gpio/gpio.h> + + mmc@5000 { + compatible = "arm,pl180", "arm,primecell"; + reg = <0x5000 0x1000>; + interrupts-extended = <&vic 22 &sic 1>; + clocks = <&xtal24mhz>, <&pclk>; + clock-names = "mclk", "apb_pclk"; + }; + + mmc@80126000 { + compatible = "arm,pl18x", "arm,primecell"; + reg = <0x80126000 0x1000>; + interrupts = <0 60 IRQ_TYPE_LEVEL_HIGH>; + dmas = <&dma 29 0 0x2>, <&dma 29 0 0x0>; + dma-names = "rx", "tx"; + clocks = <&prcc_kclk 1 5>, <&prcc_pclk 1 5>; + clock-names = "sdi", "apb_pclk"; + max-frequency = <100000000>; + bus-width = <4>; + cap-sd-highspeed; + cap-mmc-highspeed; + cd-gpios = <&gpio2 31 0x4>; + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-dir-cmd; + st,sig-pin-fbclk; + vmmc-supply = <&ab8500_ldo_aux3_reg>; + vqmmc-supply = <&vmmci>; + }; + + mmc@101f6000 { + compatible = "arm,pl18x", "arm,primecell"; + reg = <0x101f6000 0x1000>; + clocks = <&sdiclk>, <&pclksdi>; + clock-names = "mclk", "apb_pclk"; + interrupt-parent = <&vica>; + interrupts = <22>; + max-frequency = <400000>; + bus-width = <4>; + cap-mmc-highspeed; + cap-sd-highspeed; + full-pwr-cycle; + st,sig-dir-dat0; + st,sig-dir-dat2; + st,sig-dir-dat31; + st,sig-dir-cmd; + st,sig-pin-fbclk; + vmmc-supply = <&vmmc_regulator>; + }; + + mmc@52007000 { + compatible = "arm,pl18x", "arm,primecell"; + arm,primecell-periphid = <0x10153180>; + reg = <0x52007000 0x1000>; + interrupts = <49>; + interrupt-names = "cmd_irq"; + clocks = <&rcc 0>; + clock-names = "apb_pclk"; + resets = <&rcc 1>; + cap-sd-highspeed; + cap-mmc-highspeed; + max-frequency = <120000000>; + }; |