diff options
| -rw-r--r-- | arch/mips/Kconfig | 2 | ||||
| -rw-r--r-- | arch/mips/netlogic/xlr/platform.c | 89 |
2 files changed, 91 insertions, 0 deletions
diff --git a/arch/mips/Kconfig b/arch/mips/Kconfig index b3e10fdd3898..96bad981cd42 100644 --- a/arch/mips/Kconfig +++ b/arch/mips/Kconfig @@ -787,6 +787,8 @@ config NLM_XLR_BOARD select ZONE_DMA if 64BIT select SYNC_R4K select SYS_HAS_EARLY_PRINTK + select USB_ARCH_HAS_OHCI if USB_SUPPORT + select USB_ARCH_HAS_EHCI if USB_SUPPORT help Support for systems based on Netlogic XLR and XLS processors. Say Y here if you have a XLR or XLS based board. diff --git a/arch/mips/netlogic/xlr/platform.c b/arch/mips/netlogic/xlr/platform.c index eab64b45dffd..cb0ab63089db 100644 --- a/arch/mips/netlogic/xlr/platform.c +++ b/arch/mips/netlogic/xlr/platform.c @@ -97,3 +97,92 @@ static int __init nlm_uart_init(void) } arch_initcall(nlm_uart_init); + +#ifdef CONFIG_USB +/* Platform USB devices, only on XLS chips */ +static u64 xls_usb_dmamask = ~(u32)0; +#define USB_PLATFORM_DEV(n, i, irq) \ + { \ + .name = n, \ + .id = i, \ + .num_resources = 2, \ + .dev = { \ + .dma_mask = &xls_usb_dmamask, \ + .coherent_dma_mask = 0xffffffff, \ + }, \ + .resource = (struct resource[]) { \ + { \ + .flags = IORESOURCE_MEM, \ + }, \ + { \ + .start = irq, \ + .end = irq, \ + .flags = IORESOURCE_IRQ, \ + }, \ + }, \ + } + +static struct platform_device xls_usb_ehci_device = + USB_PLATFORM_DEV("ehci-xls", 0, PIC_USB_IRQ); +static struct platform_device xls_usb_ohci_device_0 = + USB_PLATFORM_DEV("ohci-xls-0", 1, PIC_USB_IRQ); +static struct platform_device xls_usb_ohci_device_1 = + USB_PLATFORM_DEV("ohci-xls-1", 2, PIC_USB_IRQ); + +static struct platform_device *xls_platform_devices[] = { + &xls_usb_ehci_device, + &xls_usb_ohci_device_0, + &xls_usb_ohci_device_1, +}; + +int xls_platform_usb_init(void) +{ + uint64_t usb_mmio, gpio_mmio; + unsigned long memres; + uint32_t val; + + if (!nlm_chip_is_xls()) + return 0; + + gpio_mmio = nlm_mmio_base(NETLOGIC_IO_GPIO_OFFSET); + usb_mmio = nlm_mmio_base(NETLOGIC_IO_USB_1_OFFSET); + + /* Clear Rogue Phy INTs */ + nlm_write_reg(usb_mmio, 49, 0x10000000); + /* Enable all interrupts */ + nlm_write_reg(usb_mmio, 50, 0x1f000000); + + /* Enable ports */ + nlm_write_reg(usb_mmio, 1, 0x07000500); + + val = nlm_read_reg(gpio_mmio, 21); + if (((val >> 22) & 0x01) == 0) { + pr_info("Detected USB Device mode - Not supported!\n"); + nlm_write_reg(usb_mmio, 0, 0x01000000); + return 0; + } + + pr_info("Detected USB Host mode - Adding XLS USB devices.\n"); + /* Clear reset, host mode */ + nlm_write_reg(usb_mmio, 0, 0x02000000); + + /* Memory resource for various XLS usb ports */ + usb_mmio = nlm_mmio_base(NETLOGIC_IO_USB_0_OFFSET); + memres = CPHYSADDR((unsigned long)usb_mmio); + xls_usb_ehci_device.resource[0].start = memres; + xls_usb_ehci_device.resource[0].end = memres + 0x400 - 1; + + memres += 0x400; + xls_usb_ohci_device_0.resource[0].start = memres; + xls_usb_ohci_device_0.resource[0].end = memres + 0x400 - 1; + + memres += 0x400; + xls_usb_ohci_device_1.resource[0].start = memres; + xls_usb_ohci_device_1.resource[0].end = memres + 0x400 - 1; + + return platform_add_devices(xls_platform_devices, + ARRAY_SIZE(xls_platform_devices)); +} + +arch_initcall(xls_platform_usb_init); +#endif |