diff options
| -rw-r--r-- | Documentation/devicetree/bindings/net/ethernet-phy.yaml | 178 | ||||
| -rw-r--r-- | Documentation/devicetree/bindings/net/phy.txt | 80 |
2 files changed, 179 insertions, 79 deletions
diff --git a/Documentation/devicetree/bindings/net/ethernet-phy.yaml b/Documentation/devicetree/bindings/net/ethernet-phy.yaml new file mode 100644 index 000000000000..b8d87135e11f --- /dev/null +++ b/Documentation/devicetree/bindings/net/ethernet-phy.yaml @@ -0,0 +1,178 @@ +# SPDX-License-Identifier: GPL-2.0 +%YAML 1.2 +--- +$id: http://devicetree.org/schemas/net/ethernet-phy.yaml# +$schema: http://devicetree.org/meta-schemas/core.yaml# + +title: Ethernet PHY Generic Binding + +maintainers: + - Andrew Lunn <andrew@lunn.ch> + - Florian Fainelli <f.fainelli@gmail.com> + - Heiner Kallweit <hkallweit1@gmail.com> + +# The dt-schema tools will generate a select statement first by using +# the compatible, and second by using the node name if any. In our +# case, the node name is the one we want to match on, while the +# compatible is optional. +select: + properties: + $nodename: + pattern: "^ethernet-phy(@[a-f0-9]+)?$" + + required: + - $nodename + +properties: + $nodename: + pattern: "^ethernet-phy(@[a-f0-9]+)?$" + + compatible: + oneOf: + - const: ethernet-phy-ieee802.3-c22 + description: PHYs that implement IEEE802.3 clause 22 + - const: ethernet-phy-ieee802.3-c45 + description: PHYs that implement IEEE802.3 clause 45 + - pattern: "^ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$" + description: + If the PHY reports an incorrect ID (or none at all) then the + compatible list may contain an entry with the correct PHY ID + in the above form. + The first group of digits is the 16 bit Phy Identifier 1 + register, this is the chip vendor OUI bits 3:18. The + second group of digits is the Phy Identifier 2 register, + this is the chip vendor OUI bits 19:24, followed by 10 + bits of a vendor specific ID. + - items: + - pattern: "^ethernet-phy-id[a-f0-9]{4}\\.[a-f0-9]{4}$" + - const: ethernet-phy-ieee802.3-c45 + + reg: + minimum: 0 + maximum: 31 + description: + The ID number for the PHY. + + interrupts: + maxItems: 1 + + max-speed: + enum: + - 10 + - 100 + - 1000 + - 2500 + - 5000 + - 10000 + - 20000 + - 25000 + - 40000 + - 50000 + - 56000 + - 100000 + - 200000 + description: + Maximum PHY supported speed in Mbits / seconds. + + broken-turn-around: + $ref: /schemas/types.yaml#definitions/flag + description: + If set, indicates the PHY device does not correctly release + the turn around line low at the end of a MDIO transaction. + + enet-phy-lane-swap: + $ref: /schemas/types.yaml#definitions/flag + description: + If set, indicates the PHY will swap the TX/RX lanes to + compensate for the board being designed with the lanes + swapped. + + eee-broken-100tx: + $ref: /schemas/types.yaml#definitions/flag + description: + Mark the corresponding energy efficient ethernet mode as + broken and request the ethernet to stop advertising it. + + eee-broken-1000t: + $ref: /schemas/types.yaml#definitions/flag + description: + Mark the corresponding energy efficient ethernet mode as + broken and request the ethernet to stop advertising it. + + eee-broken-10gt: + $ref: /schemas/types.yaml#definitions/flag + description: + Mark the corresponding energy efficient ethernet mode as + broken and request the ethernet to stop advertising it. + + eee-broken-1000kx: + $ref: /schemas/types.yaml#definitions/flag + description: + Mark the corresponding energy efficient ethernet mode as + broken and request the ethernet to stop advertising it. + + eee-broken-10gkx4: + $ref: /schemas/types.yaml#definitions/flag + description: + Mark the corresponding energy efficient ethernet mode as + broken and request the ethernet to stop advertising it. + + eee-broken-10gkr: + $ref: /schemas/types.yaml#definitions/flag + description: + Mark the corresponding energy efficient ethernet mode as + broken and request the ethernet to stop advertising it. + + phy-is-integrated: + $ref: /schemas/types.yaml#definitions/flag + description: + If set, indicates that the PHY is integrated into the same + physical package as the Ethernet MAC. If needed, muxers + should be configured to ensure the integrated PHY is + used. The absence of this property indicates the muxers + should be configured so that the external PHY is used. + + resets: + maxItems: 1 + + reset-names: + const: phy + + reset-gpios: + maxItems: 1 + description: + The GPIO phandle and specifier for the PHY reset signal. + + reset-assert-us: + description: + Delay after the reset was asserted in microseconds. If this + property is missing the delay will be skipped. + + reset-deassert-us: + description: + Delay after the reset was deasserted in microseconds. If + this property is missing the delay will be skipped. + +required: + - reg + - interrupts + +examples: + - | + ethernet { + #address-cells = <1>; + #size-cells = <0>; + + ethernet-phy@0 { + compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c45"; + interrupt-parent = <&PIC>; + interrupts = <35 1>; + reg = <0>; + + resets = <&rst 8>; + reset-names = "phy"; + reset-gpios = <&gpio1 4 1>; + reset-assert-us = <1000>; + reset-deassert-us = <2000>; + }; + }; diff --git a/Documentation/devicetree/bindings/net/phy.txt b/Documentation/devicetree/bindings/net/phy.txt index 9b9e5b1765dd..2399ee60caed 100644 --- a/Documentation/devicetree/bindings/net/phy.txt +++ b/Documentation/devicetree/bindings/net/phy.txt @@ -1,79 +1 @@ -PHY nodes - -Required properties: - - - interrupts : interrupt specifier for the sole interrupt. - - reg : The ID number for the phy, usually a small integer - -Optional Properties: - -- compatible: Compatible list, may contain - "ethernet-phy-ieee802.3-c22" or "ethernet-phy-ieee802.3-c45" for - PHYs that implement IEEE802.3 clause 22 or IEEE802.3 clause 45 - specifications. If neither of these are specified, the default is to - assume clause 22. - - If the PHY reports an incorrect ID (or none at all) then the - "compatible" list may contain an entry with the correct PHY ID in the - form: "ethernet-phy-idAAAA.BBBB" where - AAAA - The value of the 16 bit Phy Identifier 1 register as - 4 hex digits. This is the chip vendor OUI bits 3:18 - BBBB - The value of the 16 bit Phy Identifier 2 register as - 4 hex digits. This is the chip vendor OUI bits 19:24, - followed by 10 bits of a vendor specific ID. - - The compatible list should not contain other values than those - listed here. - -- max-speed: Maximum PHY supported speed (10, 100, 1000...) - -- broken-turn-around: If set, indicates the PHY device does not correctly - release the turn around line low at the end of a MDIO transaction. - -- enet-phy-lane-swap: If set, indicates the PHY will swap the TX/RX lanes to - compensate for the board being designed with the lanes swapped. - -- enet-phy-lane-no-swap: If set, indicates that PHY will disable swap of the - TX/RX lanes. This property allows the PHY to work correcly after e.g. wrong - bootstrap configuration caused by issues in PCB layout design. - -- eee-broken-100tx: -- eee-broken-1000t: -- eee-broken-10gt: -- eee-broken-1000kx: -- eee-broken-10gkx4: -- eee-broken-10gkr: - Mark the corresponding energy efficient ethernet mode as broken and - request the ethernet to stop advertising it. - -- phy-is-integrated: If set, indicates that the PHY is integrated into the same - physical package as the Ethernet MAC. If needed, muxers should be configured - to ensure the integrated PHY is used. The absence of this property indicates - the muxers should be configured so that the external PHY is used. - -- resets: The reset-controller phandle and specifier for the PHY reset signal. - -- reset-names: Must be "phy" for the PHY reset signal. - -- reset-gpios: The GPIO phandle and specifier for the PHY reset signal. - -- reset-assert-us: Delay after the reset was asserted in microseconds. - If this property is missing the delay will be skipped. - -- reset-deassert-us: Delay after the reset was deasserted in microseconds. - If this property is missing the delay will be skipped. - -Example: - -ethernet-phy@0 { - compatible = "ethernet-phy-id0141.0e90", "ethernet-phy-ieee802.3-c22"; - interrupt-parent = <&PIC>; - interrupts = <35 IRQ_TYPE_EDGE_RISING>; - reg = <0>; - - resets = <&rst 8>; - reset-names = "phy"; - reset-gpios = <&gpio1 4 GPIO_ACTIVE_LOW>; - reset-assert-us = <1000>; - reset-deassert-us = <2000>; -}; +This file has moved to ethernet-phy.yaml. |