diff options
| -rw-r--r-- | Documentation/filesystems/ext4/ext4.rst | 821 |
1 files changed, 391 insertions, 430 deletions
diff --git a/Documentation/filesystems/ext4/ext4.rst b/Documentation/filesystems/ext4/ext4.rst index 9d4368d591fa..e2b6bb7c2730 100644 --- a/Documentation/filesystems/ext4/ext4.rst +++ b/Documentation/filesystems/ext4/ext4.rst @@ -101,269 +101,256 @@ Options When mounting an ext4 filesystem, the following option are accepted: (*) == default -======================= ======================================================= -Mount Option Description -======================= ======================================================= -ro Mount filesystem read only. Note that ext4 will - replay the journal (and thus write to the - partition) even when mounted "read only". The - mount options "ro,noload" can be used to prevent - writes to the filesystem. - -journal_checksum Enable checksumming of the journal transactions. - This will allow the recovery code in e2fsck and the - kernel to detect corruption in the kernel. It is a - compatible change and will be ignored by older kernels. - -journal_async_commit Commit block can be written to disk without waiting - for descriptor blocks. If enabled older kernels cannot - mount the device. This will enable 'journal_checksum' - internally. - -journal_path=path -journal_dev=devnum When the external journal device's major/minor numbers - have changed, these options allow the user to specify - the new journal location. The journal device is - identified through either its new major/minor numbers - encoded in devnum, or via a path to the device. - -norecovery Don't load the journal on mounting. Note that -noload if the filesystem was not unmounted cleanly, - skipping the journal replay will lead to the - filesystem containing inconsistencies that can - lead to any number of problems. - -data=journal All data are committed into the journal prior to being - written into the main file system. Enabling - this mode will disable delayed allocation and - O_DIRECT support. - -data=ordered (*) All data are forced directly out to the main file - system prior to its metadata being committed to the - journal. - -data=writeback Data ordering is not preserved, data may be written - into the main file system after its metadata has been - committed to the journal. - -commit=nrsec (*) Ext4 can be told to sync all its data and metadata - every 'nrsec' seconds. The default value is 5 seconds. - This means that if you lose your power, you will lose - as much as the latest 5 seconds of work (your - filesystem will not be damaged though, thanks to the - journaling). This default value (or any low value) - will hurt performance, but it's good for data-safety. - Setting it to 0 will have the same effect as leaving - it at the default (5 seconds). - Setting it to very large values will improve - performance. - -barrier=<0|1(*)> This enables/disables the use of write barriers in -barrier(*) the jbd code. barrier=0 disables, barrier=1 enables. -nobarrier This also requires an IO stack which can support - barriers, and if jbd gets an error on a barrier - write, it will disable again with a warning. - Write barriers enforce proper on-disk ordering - of journal commits, making volatile disk write caches - safe to use, at some performance penalty. If - your disks are battery-backed in one way or another, - disabling barriers may safely improve performance. - The mount options "barrier" and "nobarrier" can - also be used to enable or disable barriers, for - consistency with other ext4 mount options. - -inode_readahead_blks=n This tuning parameter controls the maximum - number of inode table blocks that ext4's inode - table readahead algorithm will pre-read into - the buffer cache. The default value is 32 blocks. - -nouser_xattr Disables Extended User Attributes. See the - attr(5) manual page for more information about - extended attributes. - -noacl This option disables POSIX Access Control List - support. If ACL support is enabled in the kernel - configuration (CONFIG_EXT4_FS_POSIX_ACL), ACL is - enabled by default on mount. See the acl(5) manual - page for more information about acl. - -bsddf (*) Make 'df' act like BSD. -minixdf Make 'df' act like Minix. - -debug Extra debugging information is sent to syslog. - -abort Simulate the effects of calling ext4_abort() for - debugging purposes. This is normally used while - remounting a filesystem which is already mounted. - -errors=remount-ro Remount the filesystem read-only on an error. -errors=continue Keep going on a filesystem error. -errors=panic Panic and halt the machine if an error occurs. - (These mount options override the errors behavior - specified in the superblock, which can be configured - using tune2fs) - -data_err=ignore(*) Just print an error message if an error occurs - in a file data buffer in ordered mode. -data_err=abort Abort the journal if an error occurs in a file - data buffer in ordered mode. - -grpid New objects have the group ID of their parent. -bsdgroups - -nogrpid (*) New objects have the group ID of their creator. -sysvgroups - -resgid=n The group ID which may use the reserved blocks. - -resuid=n The user ID which may use the reserved blocks. - -sb=n Use alternate superblock at this location. - -quota These options are ignored by the filesystem. They -noquota are used only by quota tools to recognize volumes -grpquota where quota should be turned on. See documentation -usrquota in the quota-tools package for more details - (http://sourceforge.net/projects/linuxquota). - -jqfmt=<quota type> These options tell filesystem details about quota -usrjquota=<file> so that quota information can be properly updated -grpjquota=<file> during journal replay. They replace the above - quota options. See documentation in the quota-tools - package for more details - (http://sourceforge.net/projects/linuxquota). - -stripe=n Number of filesystem blocks that mballoc will try - to use for allocation size and alignment. For RAID5/6 - systems this should be the number of data - disks * RAID chunk size in file system blocks. - -delalloc (*) Defer block allocation until just before ext4 - writes out the block(s) in question. This - allows ext4 to better allocation decisions - more efficiently. -nodelalloc Disable delayed allocation. Blocks are allocated - when the data is copied from userspace to the - page cache, either via the write(2) system call - or when an mmap'ed page which was previously - unallocated is written for the first time. - -max_batch_time=usec Maximum amount of time ext4 should wait for - additional filesystem operations to be batch - together with a synchronous write operation. - Since a synchronous write operation is going to - force a commit and then a wait for the I/O - complete, it doesn't cost much, and can be a - huge throughput win, we wait for a small amount - of time to see if any other transactions can - piggyback on the synchronous write. The - algorithm used is designed to automatically tune - for the speed of the disk, by measuring the - amount of time (on average) that it takes to - finish committing a transaction. Call this time - the "commit time". If the time that the - transaction has been running is less than the - commit time, ext4 will try sleeping for the - commit time to see if other operations will join - the transaction. The commit time is capped by - the max_batch_time, which defaults to 15000us - (15ms). This optimization can be turned off - entirely by setting max_batch_time to 0. - -min_batch_time=usec This parameter sets the commit time (as - described above) to be at least min_batch_time. - It defaults to zero microseconds. Increasing - this parameter may improve the throughput of - multi-threaded, synchronous workloads on very - fast disks, at the cost of increasing latency. - -journal_ioprio=prio The I/O priority (from 0 to 7, where 0 is the - highest priority) which should be used for I/O - operations submitted by kjournald2 during a - commit operation. This defaults to 3, which is - a slightly higher priority than the default I/O - priority. - -auto_da_alloc(*) Many broken applications don't use fsync() when -noauto_da_alloc replacing existing files via patterns such as - fd = open("foo.new")/write(fd,..)/close(fd)/ - rename("foo.new", "foo"), or worse yet, - fd = open("foo", O_TRUNC)/write(fd,..)/close(fd). - If auto_da_alloc is enabled, ext4 will detect - the replace-via-rename and replace-via-truncate - patterns and force that any delayed allocation - blocks are allocated such that at the next - journal commit, in the default data=ordered - mode, the data blocks of the new file are forced - to disk before the rename() operation is - committed. This provides roughly the same level - of guarantees as ext3, and avoids the - "zero-length" problem that can happen when a - system crashes before the delayed allocation - blocks are forced to disk. - -noinit_itable Do not initialize any uninitialized inode table - blocks in the background. This feature may be - used by installation CD's so that the install - process can complete as quickly as possible; the - inode table initialization process would then be - deferred until the next time the file system - is unmounted. - -init_itable=n The lazy itable init code will wait n times the - number of milliseconds it took to zero out the - previous block group's inode table. This - minimizes the impact on the system performance - while file system's inode table is being initialized. - -discard Controls whether ext4 should issue discard/TRIM -nodiscard(*) commands to the underlying block device when - blocks are freed. This is useful for SSD devices - and sparse/thinly-provisioned LUNs, but it is off - by default until sufficient testing has been done. - -nouid32 Disables 32-bit UIDs and GIDs. This is for - interoperability with older kernels which only - store and expect 16-bit values. - -block_validity(*) These options enable or disable the in-kernel -noblock_validity facility for tracking filesystem metadata blocks - within internal data structures. This allows multi- - block allocator and other routines to notice - bugs or corrupted allocation bitmaps which cause - blocks to be allocated which overlap with - filesystem metadata blocks. - -dioread_lock Controls whether or not ext4 should use the DIO read -dioread_nolock locking. If the dioread_nolock option is specified - ext4 will allocate uninitialized extent before buffer - write and convert the extent to initialized after IO - completes. This approach allows ext4 code to avoid - using inode mutex, which improves scalability on high - speed storages. However this does not work with - data journaling and dioread_nolock option will be - ignored with kernel warning. Note that dioread_nolock - code path is only used for extent-based files. - Because of the restrictions this options comprises - it is off by default (e.g. dioread_lock). - -max_dir_size_kb=n This limits the size of directories so that any - attempt to expand them beyond the specified - limit in kilobytes will cause an ENOSPC error. - This is useful in memory constrained - environments, where a very large directory can - cause severe performance problems or even - provoke the Out Of Memory killer. (For example, - if there is only 512mb memory available, a 176mb - directory may seriously cramp the system's style.) - -i_version Enable 64-bit inode version support. This option is - off by default. - -dax Use direct access (no page cache). See - Documentation/filesystems/dax.txt. Note that - this option is incompatible with data=journal. -======================= ======================================================= + ro + Mount filesystem read only. Note that ext4 will replay the journal (and + thus write to the partition) even when mounted "read only". The mount + options "ro,noload" can be used to prevent writes to the filesystem. + + journal_checksum + Enable checksumming of the journal transactions. This will allow the + recovery code in e2fsck and the kernel to detect corruption in the + kernel. It is a compatible change and will be ignored by older + kernels. + + journal_async_commit + Commit block can be written to disk without waiting for descriptor + blocks. If enabled older kernels cannot mount the device. This will + enable 'journal_checksum' internally. + + journal_path=path, journal_dev=devnum + When the external journal device's major/minor numbers have changed, + these options allow the user to specify the new journal location. The + journal device is identified through either its new major/minor numbers + encoded in devnum, or via a path to the device. + + norecovery, noload + Don't load the journal on mounting. Note that if the filesystem was + not unmounted cleanly, skipping the journal replay will lead to the + filesystem containing inconsistencies that can lead to any number of + problems. + + data=journal + All data are committed into the journal prior to being written into the + main file system. Enabling this mode will disable delayed allocation + and O_DIRECT support. + + data=ordered (*) + All data are forced directly out to the main file system prior to its + metadata being committed to the journal. + + data=writeback + Data ordering is not preserved, data may be written into the main file + system after its metadata has been committed to the journal. + + commit=nrsec (*) + Ext4 can be told to sync all its data and metadata every 'nrsec' + seconds. The default value is 5 seconds. This means that if you lose + your power, you will lose as much as the latest 5 seconds of work (your + filesystem will not be damaged though, thanks to the journaling). This + default value (or any low value) will hurt performance, but it's good + for data-safety. Setting it to 0 will have the same effect as leaving + it at the default (5 seconds). Setting it to very large values will + improve performance. + + barrier=<0|1(*)>, barrier(*), nobarrier + This enables/disables the use of write barriers in the jbd code. + barrier=0 disables, barrier=1 enables. This also requires an IO stack + which can support barriers, and if jbd gets an error on a barrier + write, it will disable again with a warning. Write barriers enforce + proper on-disk ordering of journal commits, making volatile disk write + caches safe to use, at some performance penalty. If your disks are + battery-backed in one way or another, disabling barriers may safely + improve performance. The mount options "barrier" and "nobarrier" can + also be used to enable or disable barriers, for consistency with other + ext4 mount options. + + inode_readahead_blks=n + This tuning parameter controls the maximum number of inode table blocks + that ext4's inode table readahead algorithm will pre-read into the + buffer cache. The default value is 32 blocks. + + nouser_xattr + Disables Extended User Attributes. See the attr(5) manual page for + more information about extended attributes. + + noacl + This option disables POSIX Access Control List support. If ACL support + is enabled in the kernel configuration (CONFIG_EXT4_FS_POSIX_ACL), ACL + is enabled by default on mount. See the acl(5) manual page for more + information about acl. + + bsddf (*) + Make 'df' act like BSD. + + minixdf + Make 'df' act like Minix. + + debug + Extra debugging information is sent to syslog. + + abort + Simulate the effects of calling ext4_abort() for debugging purposes. + This is normally used while remounting a filesystem which is already + mounted. + + errors=remount-ro + Remount the filesystem read-only on an error. + + errors=continue + Keep going on a filesystem error. + + errors=panic + Panic and halt the machine if an error occurs. (These mount options + override the errors behavior specified in the superblock, which can be + configured using tune2fs) + + data_err=ignore(*) + Just print an error message if an error occurs in a file data buffer in + ordered mode. + data_err=abort + Abort the journal if an error occurs in a file data buffer in ordered + mode. + + grpid | bsdgroups + New objects have the group ID of their parent. + + nogrpid (*) | sysvgroups + New objects have the group ID of their creator. + + resgid=n + The group ID which may use the reserved blocks. + + resuid=n + The user ID which may use the reserved blocks. + + sb= + Use alternate superblock at this location. + + quota, noquota, grpquota, usrquota + These options are ignored by the filesystem. They are used only by + quota tools to recognize volumes where quota should be turned on. See + documentation in the quota-tools package for more details + (http://sourceforge.net/projects/linuxquota). + + jqfmt=<quota type>, usrjquota=<file>, grpjquota=<file> + These options tell filesystem details about quota so that quota + information can be properly updated during journal replay. They replace + the above quota options. See documentation in the quota-tools package + for more details (http://sourceforge.net/projects/linuxquota). + + stripe=n + Number of filesystem blocks that mballoc will try to use for allocation + size and alignment. For RAID5/6 systems this should be the number of + data disks * RAID chunk size in file system blocks. + + delalloc (*) + Defer block allocation until just before ext4 writes out the block(s) + in question. This allows ext4 to better allocation decisions more + efficiently. + + nodelalloc + Disable delayed allocation. Blocks are allocated when the data is + copied from userspace to the page cache, either via the write(2) system + call or when an mmap'ed page which was previously unallocated is + written for the first time. + + max_batch_time=usec + Maximum amount of time ext4 should wait for additional filesystem + operations to be batch together with a synchronous write operation. + Since a synchronous write operation is going to force a commit and then + a wait for the I/O complete, it doesn't cost much, and can be a huge + throughput win, we wait for a small amount of time to see if any other + transactions can piggyback on the synchronous write. The algorithm + used is designed to automatically tune for the speed of the disk, by + measuring the amount of time (on average) that it takes to finish + committing a transaction. Call this time the "commit time". If the + time that the transaction has been running is less than the commit + time, ext4 will try sleeping for the commit time to see if other + operations will join the transaction. The commit time is capped by + the max_batch_time, which defaults to 15000us (15ms). This + optimization can be turned off entirely by setting max_batch_time to 0. + + min_batch_time=usec + This parameter sets the commit time (as described above) to be at least + min_batch_time. It defaults to zero microseconds. Increasing this + parameter may improve the throughput of multi-threaded, synchronous + workloads on very fast disks, at the cost of increasing latency. + + journal_ioprio=prio + The I/O priority (from 0 to 7, where 0 is the highest priority) which + should be used for I/O operations submitted by kjournald2 during a + commit operation. This defaults to 3, which is a slightly higher + priority than the default I/O priority. + + auto_da_alloc(*), noauto_da_alloc + Many broken applications don't use fsync() when replacing existing + files via patterns such as fd = open("foo.new")/write(fd,..)/close(fd)/ + rename("foo.new", "foo"), or worse yet, fd = open("foo", + O_TRUNC)/write(fd,..)/close(fd). If auto_da_alloc is enabled, ext4 + will detect the replace-via-rename and replace-via-truncate patterns + and force that any delayed allocation blocks are allocated such that at + the next journal commit, in the default data=ordered mode, the data + blocks of the new file are forced to disk before the rename() operation + is committed. This provides roughly the same level of guarantees as + ext3, and avoids the "zero-length" problem that can happen when a + system crashes before the delayed allocation blocks are forced to disk. + + noinit_itable + Do not initialize any uninitialized inode table blocks in the + background. This feature may be used by installation CD's so that the + install process can complete as quickly as possible; the inode table + initialization process would then be deferred until the next time the + file system is unmounted. + + init_itable=n + The lazy itable init code will wait n times the number of milliseconds + it took to zero out the previous block group's inode table. This + minimizes the impact on the system performance while file system's + inode table is being initialized. + + discard, nodiscard(*) + Controls whether ext4 should issue discard/TRIM commands to the + underlying block device when blocks are freed. This is useful for SSD + devices and sparse/thinly-provisioned LUNs, but it is off by default + until sufficient testing has been done. + + nouid32 + Disables 32-bit UIDs and GIDs. This is for interoperability with + older kernels which only store and expect 16-bit values. + + block_validity(*), noblock_validity + These options enable or disable the in-kernel facility for tracking + filesystem metadata blocks within internal data structures. This + allows multi- block allocator and other routines to notice bugs or + corrupted allocation bitmaps which cause blocks to be allocated which + overlap with filesystem metadata blocks. + + dioread_lock, dioread_nolock + Controls whether or not ext4 should use the DIO read locking. If the + dioread_nolock option is specified ext4 will allocate uninitialized + extent before buffer write and convert the extent to initialized after + IO completes. This approach allows ext4 code to avoid using inode + mutex, which improves scalability on high speed storages. However this + does not work with data journaling and dioread_nolock option will be + ignored with kernel warning. Note that dioread_nolock code path is only + used for extent-based files. Because of the restrictions this options + comprises it is off by default (e.g. dioread_lock). + + max_dir_size_kb=n + This limits the size of directories so that any attempt to expand them + beyond the specified limit in kilobytes will cause an ENOSPC error. + This is useful in memory constrained environments, where a very large + directory can cause severe performance problems or even provoke the Out + Of Memory killer. (For example, if there is only 512mb memory + available, a 176mb directory may seriously cramp the system's style.) + + i_version + Enable 64-bit inode version support. This option is off by default. + + dax + Use direct access (no page cache). See + Documentation/filesystems/dax.txt. Note that this option is + incompatible with data=journal. Data Mode ========= @@ -407,11 +394,8 @@ in table below. Files in /proc/fs/ext4/<devname> -================ ======= - File Content -================ ======= - mb_groups details of multiblock allocator buddy cache of free blocks -================ ======= + mb_groups + details of multiblock allocator buddy cache of free blocks /sys entries ============ @@ -426,74 +410,71 @@ Files in /sys/fs/ext4/<devname>: (see also Documentation/ABI/testing/sysfs-fs-ext4) -============================= ================================================= -File Content -============================= ================================================= - delayed_allocation_blocks This file is read-only and shows the number of - blocks that are dirty in the page cache, but - which do not have their location in the - filesystem allocated yet. - -inode_goal Tuning parameter which (if non-zero) controls - the goal inode used by the inode allocator in - preference to all other allocation heuristics. - This is intended for debugging use only, and - should be 0 on production systems. - -inode_readahead_blks Tuning parameter which controls the maximum - number of inode table blocks that ext4's inode - table readahead algorithm will pre-read into - the buffer cache - -lifetime_write_kbytes This file is read-only and shows the number of - kilobytes of data that have been written to this - filesystem since it was created. - - max_writeback_mb_bump The maximum number of megabytes the writeback - code will try to write out before move on to - another inode. - - mb_group_prealloc The multiblock allocator will round up allocation - requests to a multiple of this tuning parameter if - the stripe size is not set in the ext4 superblock - - mb_max_to_scan The maximum number of extents the multiblock - allocator will search to find the best extent - - mb_min_to_scan The minimum number of extents the multiblock - allocator will search to find the best extent - - mb_order2_req Tuning parameter which controls the minimum size - for requests (as a power of 2) where the buddy - cache is used - - mb_stats Controls whether the multiblock allocator should - collect statistics, which are shown during the - unmount. 1 means to collect statistics, 0 means - not to collect statistics - - mb_stream_req Files which have fewer blocks than this tunable - parameter will have their blocks allocated out - of a block group specific preallocation pool, so - that small files are packed closely together. - Each large file will have its blocks allocated - out of its own unique preallocation pool. - - session_write_kbytes This file is read-only and shows the number of - kilobytes of data that have been written to this - filesystem since it was mounted. - - reserved_clusters This is RW file and contains number of reserved - clusters in the file system which will be used - in the specific situations to avoid costly - zeroout, unexpected ENOSPC, or possible data - loss. The default is 2% or 4096 clusters, - whichever is smaller and this can be changed - however it can never exceed number of clusters - in the file system. If there is not enough space - for the reserved space when mounting the file - mount will _not_ fail. -============================= ================================================= + delayed_allocation_blocks + This file is read-only and shows the number of blocks that are dirty in + the page cache, but which do not have their location in the filesystem + allocated yet. + + inode_goal + Tuning parameter which (if non-zero) controls the goal inode used by + the inode allocator in preference to all other allocation heuristics. + This is intended for debugging use only, and should be 0 on production + systems. + + inode_readahead_blks + Tuning parameter which controls the maximum number of inode table + blocks that ext4's inode table readahead algorithm will pre-read into + the buffer cache. + + lifetime_write_kbytes + This file is read-only and shows the number of kilobytes of data that + have been written to this filesystem since it was created. + + max_writeback_mb_bump + The maximum number of megabytes the writeback code will try to write + out before move on to another inode. + + mb_group_prealloc + The multiblock allocator will round up allocation requests to a + multiple of this tuning parameter if the stripe size is not set in the + ext4 superblock + + mb_max_to_scan + The maximum number of extents the multiblock allocator will search to + find the best extent. + + mb_min_to_scan + The minimum number of extents the multiblock allocator will search to + find the best extent. + + mb_order2_req + Tuning parameter which controls the minimum size for requests (as a + power of 2) where the buddy cache is used. + + mb_stats + Controls whether the multiblock allocator should collect statistics, + which are shown during the unmount. 1 means to collect statistics, 0 + means not to collect statistics. + + mb_stream_req + Files which have fewer blocks than this tunable parameter will have + their blocks allocated out of a block group specific preallocation + pool, so that small files are packed closely together. Each large file + will have its blocks allocated out of its own unique preallocation + pool. + + session_write_kbytes + This file is read-only and shows the number of kilobytes of data that + have been written to this filesystem since it was mounted. + + reserved_clusters + This is RW file and contains number of reserved clusters in the file + system which will be used in the specific situations to avoid costly + zeroout, unexpected ENOSPC, or possible data loss. The default is 2% or + 4096 clusters, whichever is smaller and this can be changed however it + can never exceed number of clusters in the file system. If there is not + enough space for the reserved space when mounting the file mount will + _not_ fail. Ioctls ====== @@ -504,100 +485,80 @@ shown in the table below. Table of Ext4 specific ioctls -============================= ================================================= -Ioctl Description -============================= ================================================= - EXT4_IOC_GETFLAGS Get additional attributes associated with inode. - The ioctl argument is an integer bitfield, with - bit values described in ext4.h. This ioctl is an - alias for FS_IOC_GETFLAGS. - - EXT4_IOC_SETFLAGS Set additional attributes associated with inode. - The ioctl argument is an integer bitfield, with - bit values described in ext4.h. This ioctl is an - alias for FS_IOC_SETFLAGS. - - EXT4_IOC_GETVERSION - EXT4_IOC_GETVERSION_OLD - Get the inode i_generation number stored for - each inode. The i_generation number is normally - changed only when new inode is created and it is - particularly useful for network filesystems. The - '_OLD' version of this ioctl is an alias for - FS_IOC_GETVERSION. - - EXT4_IOC_SETVERSION - EXT4_IOC_SETVERSION_OLD - Set the inode i_generation number stored for - each inode. The '_OLD' version of this ioctl - is an alias for FS_IOC_SETVERSION. - - EXT4_IOC_GROUP_EXTEND This ioctl has the same purpose as the resize - mount option. It allows to resize filesystem - to the end of the last existing block group, - further resize has to be done with resize2fs, - either online, or offline. The argument points - to the unsigned logn number representing the - filesystem new block count. - - EXT4_IOC_MOVE_EXT Move the block extents from orig_fd (the one - this ioctl is pointing to) to the donor_fd (the - one specified in move_extent structure passed - as an argument to this ioctl). Then, exchange - inode metadata between orig_fd and donor_fd. - This is especially useful for online - defragmentation, because the allocator has the - opportunity to allocate moved blocks better, - ideally into one contiguous extent. - - EXT4_IOC_GROUP_ADD Add a new group descriptor to an existing or - new group descriptor block. The new group - descriptor is described by ext4_new_group_input - structure, which is passed as an argument to - this ioctl. This is especially useful in - conjunction with EXT4_IOC_GROUP_EXTEND, - which allows online resize of the filesystem - to the end of the last existing block group. - Those two ioctls combined is used in userspace - online resize tool (e.g. resize2fs). - - EXT4_IOC_MIGRATE This ioctl operates on the filesystem itself. - It converts (migrates) ext3 indirect block mapped - inode to ext4 extent mapped inode by walking - through indirect block mapping of the original - inode and converting contiguous block ranges - into ext4 extents of the temporary inode. Then, - inodes are swapped. This ioctl might help, when - migrating from ext3 to ext4 filesystem, however - suggestion is to create fresh ext4 filesystem - and copy data from the backup. Note, that - filesystem has to support extents for this ioctl - to work. - - EXT4_IOC_ALLOC_DA_BLKS Force all of the delay allocated blocks to be - allocated to preserve application-expected ext3 - behaviour. Note that this will also start - triggering a write of the data blocks, but this - behaviour may change in the future as it is - not necessary and has been done this way only - for sake of simplicity. - - EXT4_IOC_RESIZE_FS Resize the filesystem to a new size. The number - of blocks of resized filesystem is passed in via - 64 bit integer argument. The kernel allocates - bitmaps and inode table, the userspace tool thus - just passes the new number of blocks. - - EXT4_IOC_SWAP_BOOT Swap i_blocks and associated attributes - (like i_blocks, i_size, i_flags, ...) from - the specified inode with inode - EXT4_BOOT_LOADER_INO (#5). This is typically - used to store a boot loader in a secure part of - the filesystem, where it can't be changed by a - normal user by accident. - The data blocks of the previous boot loader - will be associated with the given inode. -============================= ================================================= + EXT4_IOC_GETFLAGS + Get additional attributes associated with inode. The ioctl argument is + an integer bitfield, with bit values described in ext4.h. This ioctl is + an alias for FS_IOC_GETFLAGS. + + EXT4_IOC_SETFLAGS + Set additional attributes associated with inode. The ioctl argument is + an integer bitfield, with bit values described in ext4.h. This ioctl is + an alias for FS_IOC_SETFLAGS. + + EXT4_IOC_GETVERSION, EXT4_IOC_GETVERSION_OLD + Get the inode i_generation number stored for each inode. The + i_generation number is normally changed only when new inode is created + and it is particularly useful for network filesystems. The '_OLD' + version of this ioctl is an alias for FS_IOC_GETVERSION. + + EXT4_IOC_SETVERSION, EXT4_IOC_SETVERSION_OLD + Set the inode i_generation number stored for each inode. The '_OLD' + version of this ioctl is an alias for FS_IOC_SETVERSION. + + EXT4_IOC_GROUP_EXTEND + This ioctl has the same purpose as the resize mount option. It allows + to resize filesystem to the end of the last existing block group, + further resize has to be done with resize2fs, either online, or + offline. The argument points to the unsigned logn number representing + the filesystem new block count. + + EXT4_IOC_MOVE_EXT + Move the block extents from orig_fd (the one this ioctl is pointing to) + to the donor_fd (the one specified in move_extent structure passed as + an argument to this ioctl). Then, exchange inode metadata between + orig_fd and donor_fd. This is especially useful for online + defragmentation, because the allocator has the opportunity to allocate + moved blocks better, ideally into one contiguous extent. + + EXT4_IOC_GROUP_ADD + Add a new group descriptor to an existing or new group descriptor + block. The new group descriptor is described by ext4_new_group_input + structure, which is passed as an argument to this ioctl. This is + especially useful in conjunction with EXT4_IOC_GROUP_EXTEND, which + allows online resize of the filesystem to the end of the last existing + block group. Those two ioctls combined is used in userspace online + resize tool (e.g. resize2fs). + + EXT4_IOC_MIGRATE + This ioctl operates on the filesystem itself. It converts (migrates) + ext3 indirect block mapped inode to ext4 extent mapped inode by walking + through indirect block mapping of the original inode and converting + contiguous block ranges into ext4 extents of the temporary inode. Then, + inodes are swapped. This ioctl might help, when migrating from ext3 to + ext4 filesystem, however suggestion is to create fresh ext4 filesystem + and copy data from the backup. Note, that filesystem has to support + extents for this ioctl to work. + + EXT4_IOC_ALLOC_DA_BLKS + Force all of the delay allocated blocks to be allocated to preserve + application-expected ext3 behaviour. Note that this will also start + triggering a write of the data blocks, but this behaviour may change in + the future as it is not necessary and has been done this way only for + sake of simplicity. + + EXT4_IOC_RESIZE_FS + Resize the filesystem to a new size. The number of blocks of resized + filesystem is passed in via 64 bit integer argument. The kernel + allocates bitmaps and inode table, the userspace tool thus just passes + the new number of blocks. + + EXT4_IOC_SWAP_BOOT + Swap i_blocks and associated attributes (like i_blocks, i_size, + i_flags, ...) from the specified inode with inode EXT4_BOOT_LOADER_INO + (#5). This is typically used to store a boot loader in a secure part of + the filesystem, where it can't be changed by a normal user by accident. + The data blocks of the previous boot loader will be associated with the + given inode. References ========== |