diff options
| -rw-r--r-- | Documentation/devicetree/bindings/gpio/gpio-tz1090.txt | 88 | ||||
| -rw-r--r-- | drivers/gpio/Kconfig | 7 | ||||
| -rw-r--r-- | drivers/gpio/Makefile | 1 | ||||
| -rw-r--r-- | drivers/gpio/gpio-tz1090.c | 633 |
4 files changed, 729 insertions, 0 deletions
diff --git a/Documentation/devicetree/bindings/gpio/gpio-tz1090.txt b/Documentation/devicetree/bindings/gpio/gpio-tz1090.txt new file mode 100644 index 000000000000..174cdf309170 --- /dev/null +++ b/Documentation/devicetree/bindings/gpio/gpio-tz1090.txt @@ -0,0 +1,88 @@ +ImgTec TZ1090 GPIO Controller + +Required properties: +- compatible: Compatible property value should be "img,tz1090-gpio". + +- reg: Physical base address of the controller and length of memory mapped + region. + +- #address-cells: Should be 1 (for bank subnodes) + +- #size-cells: Should be 0 (for bank subnodes) + +- Each bank of GPIOs should have a subnode to represent it. + + Bank subnode required properties: + - reg: Index of bank in the range 0 to 2. + + - gpio-controller: Specifies that the node is a gpio controller. + + - #gpio-cells: Should be 2. The syntax of the gpio specifier used by client + nodes should have the following values. + <[phandle of the gpio controller node] + [gpio number within the gpio bank] + [gpio flags]> + + Values for gpio specifier: + - GPIO number: a value in the range 0 to 29. + - GPIO flags: bit field of flags, as defined in <dt-bindings/gpio/gpio.h>. + Only the following flags are supported: + GPIO_ACTIVE_HIGH + GPIO_ACTIVE_LOW + + Bank subnode optional properties: + - gpio-ranges: Mapping to pin controller pins (as described in + Documentation/devicetree/bindings/gpio/gpio.txt) + + - interrupts: Interrupt for the entire bank + + - interrupt-controller: Specifies that the node is an interrupt controller + + - #interrupt-cells: Should be 2. The syntax of the interrupt specifier used by + client nodes should have the following values. + <[phandle of the interurupt controller] + [gpio number within the gpio bank] + [irq flags]> + + Values for irq specifier: + - GPIO number: a value in the range 0 to 29 + - IRQ flags: value to describe edge and level triggering, as defined in + <dt-bindings/interrupt-controller/irq.h>. Only the following flags are + supported: + IRQ_TYPE_EDGE_RISING + IRQ_TYPE_EDGE_FALLING + IRQ_TYPE_EDGE_BOTH + IRQ_TYPE_LEVEL_HIGH + IRQ_TYPE_LEVEL_LOW + + + +Example: + + gpios: gpio-controller@02005800 { + #address-cells = <1>; + #size-cells = <0>; + compatible = "img,tz1090-gpio"; + reg = <0x02005800 0x90>; + + /* bank 0 with an interrupt */ + gpios0: bank@0 { + #gpio-cells = <2>; + #interrupt-cells = <2>; + reg = <0>; + interrupts = <13 IRQ_TYPE_LEVEL_HIGH>; + gpio-controller; + gpio-ranges = <&pinctrl 0 0 30>; + interrupt-controller; + }; + + /* bank 2 without interrupt */ + gpios2: bank@2 { + #gpio-cells = <2>; + reg = <2>; + gpio-controller; + gpio-ranges = <&pinctrl 0 60 30>; + }; + }; + + diff --git a/drivers/gpio/Kconfig b/drivers/gpio/Kconfig index b2450ba14138..e9761641f149 100644 --- a/drivers/gpio/Kconfig +++ b/drivers/gpio/Kconfig @@ -242,6 +242,13 @@ config GPIO_TS5500 blocks of the TS-5500: DIO1, DIO2 and the LCD port, and the TS-5600 LCD port. +config GPIO_TZ1090 + bool "Toumaz Xenif TZ1090 GPIO support" + depends on SOC_TZ1090 + default y + help + Say yes here to support Toumaz Xenif TZ1090 GPIOs. + config GPIO_XILINX bool "Xilinx GPIO support" depends on PPC_OF || MICROBLAZE || ARCH_ZYNQ diff --git a/drivers/gpio/Makefile b/drivers/gpio/Makefile index ef3e983a2f1e..2baf456392f9 100644 --- a/drivers/gpio/Makefile +++ b/drivers/gpio/Makefile @@ -79,6 +79,7 @@ obj-$(CONFIG_GPIO_TPS65912) += gpio-tps65912.o obj-$(CONFIG_GPIO_TS5500) += gpio-ts5500.o obj-$(CONFIG_GPIO_TWL4030) += gpio-twl4030.o obj-$(CONFIG_GPIO_TWL6040) += gpio-twl6040.o +obj-$(CONFIG_GPIO_TZ1090) += gpio-tz1090.o obj-$(CONFIG_GPIO_UCB1400) += gpio-ucb1400.o obj-$(CONFIG_GPIO_VIPERBOARD) += gpio-viperboard.o obj-$(CONFIG_GPIO_VR41XX) += gpio-vr41xx.o diff --git a/drivers/gpio/gpio-tz1090.c b/drivers/gpio/gpio-tz1090.c new file mode 100644 index 000000000000..b725a6bef3e1 --- /dev/null +++ b/drivers/gpio/gpio-tz1090.c @@ -0,0 +1,633 @@ +/* + * Toumaz Xenif TZ1090 GPIO handling. + * + * Copyright (C) 2008-2013 Imagination Technologies Ltd. + * + * Based on ARM PXA code and others. + * + * This program is free software; you can redistribute it and/or modify + * it under the terms of the GNU General Public License version 2 as + * published by the Free Software Foundation. + */ + +#include <linux/bitops.h> +#include <linux/export.h> +#include <linux/gpio.h> +#include <linux/interrupt.h> +#include <linux/io.h> +#include <linux/irq.h> +#include <linux/irqdomain.h> +#include <linux/kernel.h> +#include <linux/of_irq.h> +#include <linux/pinctrl/consumer.h> +#include <linux/platform_device.h> +#include <linux/slab.h> +#include <linux/syscore_ops.h> +#include <asm/global_lock.h> + +/* Register offsets from bank base address */ +#define REG_GPIO_DIR 0x00 +#define REG_GPIO_IRQ_PLRT 0x20 +#define REG_GPIO_IRQ_TYPE 0x30 +#define REG_GPIO_IRQ_EN 0x40 +#define REG_GPIO_IRQ_STS 0x50 +#define REG_GPIO_BIT_EN 0x60 +#define REG_GPIO_DIN 0x70 +#define REG_GPIO_DOUT 0x80 + +/* REG_GPIO_IRQ_PLRT */ +#define REG_GPIO_IRQ_PLRT_LOW 0 +#define REG_GPIO_IRQ_PLRT_HIGH 1 + +/* REG_GPIO_IRQ_TYPE */ +#define REG_GPIO_IRQ_TYPE_LEVEL 0 +#define REG_GPIO_IRQ_TYPE_EDGE 1 + +/** + * struct tz1090_gpio_bank - GPIO bank private data + * @chip: Generic GPIO chip for GPIO bank + * @domain: IRQ domain for GPIO bank (may be NULL) + * @reg: Base of registers, offset for this GPIO bank + * @irq: IRQ number for GPIO bank + * @label: Debug GPIO bank label, used for storage of chip->label + * + * This is the main private data for a GPIO bank. It encapsulates a gpio_chip, + * and the callbacks for the gpio_chip can access the private data with the + * to_bank() macro below. + */ +struct tz1090_gpio_bank { + struct gpio_chip chip; + struct irq_domain *domain; + void __iomem *reg; + int irq; + char label[16]; +}; +#define to_bank(c) container_of(c, struct tz1090_gpio_bank, chip) + +/** + * struct tz1090_gpio - Overall GPIO device private data + * @dev: Device (from platform device) + * @reg: Base of GPIO registers + * + * Represents the overall GPIO device. This structure is actually only + * temporary, and used during init. + */ +struct tz1090_gpio { + struct device *dev; + void __iomem *reg; +}; + +/** + * struct tz1090_gpio_bank_info - Temporary registration info for GPIO bank + * @priv: Overall GPIO device private data + * @node: Device tree node specific to this GPIO bank + * @index: Index of bank in range 0-2 + */ +struct tz1090_gpio_bank_info { + struct tz1090_gpio *priv; + struct device_node *node; + unsigned int index; +}; + +/* Convenience register accessors */ +static inline void tz1090_gpio_write(struct tz1090_gpio_bank *bank, + unsigned int reg_offs, u32 data) +{ + iowrite32(data, bank->reg + reg_offs); +} + +static inline u32 tz1090_gpio_read(struct tz1090_gpio_bank *bank, + unsigned int reg_offs) +{ + return ioread32(bank->reg + reg_offs); +} + +/* caller must hold LOCK2 */ +static inline void _tz1090_gpio_clear_bit(struct tz1090_gpio_bank *bank, + unsigned int reg_offs, + unsigned int offset) +{ + u32 value; + + value = tz1090_gpio_read(bank, reg_offs); + value &= ~BIT(offset); + tz1090_gpio_write(bank, reg_offs, value); +} + +static void tz1090_gpio_clear_bit(struct tz1090_gpio_bank *bank, + unsigned int reg_offs, + unsigned int offset) +{ + int lstat; + + __global_lock2(lstat); + _tz1090_gpio_clear_bit(bank, reg_offs, offset); + __global_unlock2(lstat); +} + +/* caller must hold LOCK2 */ +static inline void _tz1090_gpio_set_bit(struct tz1090_gpio_bank *bank, + unsigned int reg_offs, + unsigned int offset) +{ + u32 value; + + value = tz1090_gpio_read(bank, reg_offs); + value |= BIT(offset); + tz1090_gpio_write(bank, reg_offs, value); +} + +static void tz1090_gpio_set_bit(struct tz1090_gpio_bank *bank, + unsigned int reg_offs, + unsigned int offset) +{ + int lstat; + + __global_lock2(lstat); + _tz1090_gpio_set_bit(bank, reg_offs, offset); + __global_unlock2(lstat); +} + +/* caller must hold LOCK2 */ +static inline void _tz1090_gpio_mod_bit(struct tz1090_gpio_bank *bank, + unsigned int reg_offs, + unsigned int offset, + bool val) +{ + u32 value; + + value = tz1090_gpio_read(bank, reg_offs); + value &= ~BIT(offset); + if (val) + value |= BIT(offset); + tz1090_gpio_write(bank, reg_offs, value); +} + +static void tz1090_gpio_mod_bit(struct tz1090_gpio_bank *bank, + unsigned int reg_offs, + unsigned int offset, + bool val) +{ + int lstat; + + __global_lock2(lstat); + _tz1090_gpio_mod_bit(bank, reg_offs, offset, val); + __global_unlock2(lstat); +} + +static inline int tz1090_gpio_read_bit(struct tz1090_gpio_bank *bank, + unsigned int reg_offs, + unsigned int offset) +{ + return tz1090_gpio_read(bank, reg_offs) & BIT(offset); +} + +/* GPIO chip callbacks */ + +static int tz1090_gpio_direction_input(struct gpio_chip *chip, + unsigned int offset) +{ + struct tz1090_gpio_bank *bank = to_bank(chip); + tz1090_gpio_set_bit(bank, REG_GPIO_DIR, offset); + + return 0; +} + +static int tz1090_gpio_direction_output(struct gpio_chip *chip, + unsigned int offset, int output_value) +{ + struct tz1090_gpio_bank *bank = to_bank(chip); + int lstat; + + __global_lock2(lstat); + _tz1090_gpio_mod_bit(bank, REG_GPIO_DOUT, offset, output_value); + _tz1090_gpio_clear_bit(bank, REG_GPIO_DIR, offset); + __global_unlock2(lstat); + + return 0; +} + +/* + * Return GPIO level + */ +static int tz1090_gpio_get(struct gpio_chip *chip, unsigned int offset) +{ + struct tz1090_gpio_bank *bank = to_bank(chip); + + return tz1090_gpio_read_bit(bank, REG_GPIO_DIN, offset); +} + +/* + * Set output GPIO level + */ +static void tz1090_gpio_set(struct gpio_chip *chip, unsigned int offset, + int output_value) +{ + struct tz1090_gpio_bank *bank = to_bank(chip); + + tz1090_gpio_mod_bit(bank, REG_GPIO_DOUT, offset, output_value); +} + +static int tz1090_gpio_request(struct gpio_chip *chip, unsigned int offset) +{ + struct tz1090_gpio_bank *bank = to_bank(chip); + int ret; + + ret = pinctrl_request_gpio(chip->base + offset); + if (ret) + return ret; + + tz1090_gpio_set_bit(bank, REG_GPIO_DIR, offset); + tz1090_gpio_set_bit(bank, REG_GPIO_BIT_EN, offset); + + return 0; +} + +static void tz1090_gpio_free(struct gpio_chip *chip, unsigned int offset) +{ + struct tz1090_gpio_bank *bank = to_bank(chip); + + pinctrl_free_gpio(chip->base + offset); + + tz1090_gpio_clear_bit(bank, REG_GPIO_BIT_EN, offset); +} + +static int tz1090_gpio_to_irq(struct gpio_chip *chip, unsigned int offset) +{ + struct tz1090_gpio_bank *bank = to_bank(chip); + + if (!bank->domain) + return -EINVAL; + + return irq_create_mapping(bank->domain, offset); +} + +/* IRQ chip handlers */ + +/* Get TZ1090 GPIO chip from irq data provided to generic IRQ callbacks */ +static inline struct tz1090_gpio_bank *irqd_to_gpio_bank(struct irq_data *data) +{ + return (struct tz1090_gpio_bank *)data->domain->host_data; +} + +static void tz1090_gpio_irq_clear(struct tz1090_gpio_bank *bank, + unsigned int offset) +{ + tz1090_gpio_clear_bit(bank, REG_GPIO_IRQ_STS, offset); +} + +static void tz1090_gpio_irq_enable(struct tz1090_gpio_bank *bank, + unsigned int offset, bool enable) +{ + tz1090_gpio_mod_bit(bank, REG_GPIO_IRQ_EN, offset, enable); +} + +static void tz1090_gpio_irq_polarity(struct tz1090_gpio_bank *bank, + unsigned int offset, unsigned int polarity) +{ + tz1090_gpio_mod_bit(bank, REG_GPIO_IRQ_PLRT, offset, polarity); +} + +static int tz1090_gpio_valid_handler(struct irq_desc *desc) +{ + return desc->handle_irq == handle_level_irq || + desc->handle_irq == handle_edge_irq; +} + +static void tz1090_gpio_irq_type(struct tz1090_gpio_bank *bank, + unsigned int offset, unsigned int type) +{ + tz1090_gpio_mod_bit(bank, REG_GPIO_IRQ_TYPE, offset, type); +} + +/* set polarity to trigger on next edge, whether rising or falling */ +static void tz1090_gpio_irq_next_edge(struct tz1090_gpio_bank *bank, + unsigned int offset) +{ + unsigned int value_p, value_i; + int lstat; + + /* + * Set the GPIO's interrupt polarity to the opposite of the current + * input value so that the next edge triggers an interrupt. + */ + __global_lock2(lstat); + value_i = ~tz1090_gpio_read(bank, REG_GPIO_DIN); + value_p = tz1090_gpio_read(bank, REG_GPIO_IRQ_PLRT); + value_p &= ~BIT(offset); + value_p |= value_i & BIT(offset); + tz1090_gpio_write(bank, REG_GPIO_IRQ_PLRT, value_p); + __global_unlock2(lstat); +} + +static void gpio_ack_irq(struct irq_data *data) +{ + struct tz1090_gpio_bank *bank = irqd_to_gpio_bank(data); + + tz1090_gpio_irq_clear(bank, data->hwirq); +} + +static void gpio_mask_irq(struct irq_data *data) +{ + struct tz1090_gpio_bank *bank = irqd_to_gpio_bank(data); + + tz1090_gpio_irq_enable(bank, data->hwirq, false); +} + +static void gpio_unmask_irq(struct irq_data *data) +{ + struct tz1090_gpio_bank *bank = irqd_to_gpio_bank(data); + + tz1090_gpio_irq_enable(bank, data->hwirq, true); +} + +static unsigned int gpio_startup_irq(struct irq_data *data) +{ + struct tz1090_gpio_bank *bank = irqd_to_gpio_bank(data); + irq_hw_number_t hw = data->hwirq; + struct irq_desc *desc = irq_to_desc(data->irq); + + /* + * This warning indicates that the type of the irq hasn't been set + * before enabling the irq. This would normally be done by passing some + * trigger flags to request_irq(). + */ + WARN(!tz1090_gpio_valid_handler(desc), + "irq type not set before enabling gpio irq %d", data->irq); + + tz1090_gpio_irq_clear(bank, hw); + tz1090_gpio_irq_enable(bank, hw, true); + return 0; +} + +static int gpio_set_irq_type(struct irq_data *data, unsigned int flow_type) +{ + struct tz1090_gpio_bank *bank = irqd_to_gpio_bank(data); + unsigned int type; + unsigned int polarity; + + switch (flow_type) { + case IRQ_TYPE_EDGE_BOTH: + type = REG_GPIO_IRQ_TYPE_EDGE; + polarity = REG_GPIO_IRQ_PLRT_LOW; + break; + case IRQ_TYPE_EDGE_RISING: + type = REG_GPIO_IRQ_TYPE_EDGE; + polarity = REG_GPIO_IRQ_PLRT_HIGH; + break; + case IRQ_TYPE_EDGE_FALLING: + type = REG_GPIO_IRQ_TYPE_EDGE; + polarity = REG_GPIO_IRQ_PLRT_LOW; + break; + case IRQ_TYPE_LEVEL_HIGH: + type = REG_GPIO_IRQ_TYPE_LEVEL; + polarity = REG_GPIO_IRQ_PLRT_HIGH; + break; + case IRQ_TYPE_LEVEL_LOW: + type = REG_GPIO_IRQ_TYPE_LEVEL; + polarity = REG_GPIO_IRQ_PLRT_LOW; + break; + default: + return -EINVAL; + } + + tz1090_gpio_irq_type(bank, data->hwirq, type); + if (type == REG_GPIO_IRQ_TYPE_LEVEL) + __irq_set_handler_locked(data->irq, handle_level_irq); + else + __irq_set_handler_locked(data->irq, handle_edge_irq); + + if (flow_type == IRQ_TYPE_EDGE_BOTH) + tz1090_gpio_irq_next_edge(bank, data->hwirq); + else + tz1090_gpio_irq_polarity(bank, data->hwirq, polarity); + + return 0; +} + +#ifdef CONFIG_SUSPEND +static int gpio_set_irq_wake(struct irq_data *data, unsigned int on) +{ + struct tz1090_gpio_bank *bank = irqd_to_gpio_bank(data); + +#ifdef CONFIG_PM_DEBUG + pr_info("irq_wake irq%d state:%d\n", data->irq, on); +#endif + + /* wake on gpio block interrupt */ + return irq_set_irq_wake(bank->irq, on); +} +#else +#define gpio_set_irq_wake NULL +#endif + +/* gpio virtual interrupt functions */ +static struct irq_chip gpio_irq_chip = { + .irq_startup = gpio_startup_irq, + .irq_ack = gpio_ack_irq, + .irq_mask = gpio_mask_irq, + .irq_unmask = gpio_unmask_irq, + .irq_set_type = gpio_set_irq_type, + .irq_set_wake = gpio_set_irq_wake, + .flags = IRQCHIP_MASK_ON_SUSPEND, +}; + +static void tz1090_gpio_irq_handler(unsigned int irq, struct irq_desc *desc) +{ + irq_hw_number_t hw; + unsigned int irq_stat, irq_no; + struct tz1090_gpio_bank *bank; + struct irq_desc *child_desc; + + bank = (struct tz1090_gpio_bank *)irq_desc_get_handler_data(desc); + irq_stat = tz1090_gpio_read(bank, REG_GPIO_DIR) & + tz1090_gpio_read(bank, REG_GPIO_IRQ_STS) & + tz1090_gpio_read(bank, REG_GPIO_IRQ_EN) & + 0x3FFFFFFF; /* 30 bits only */ + + for (hw = 0; irq_stat; irq_stat >>= 1, ++hw) { + if (!(irq_stat & 1)) + continue; + + irq_no = irq_linear_revmap(bank->domain, hw); + child_desc = irq_to_desc(irq_no); + + /* Toggle edge for pin with both edges triggering enabled */ + if (irqd_get_trigger_type(&child_desc->irq_data) + == IRQ_TYPE_EDGE_BOTH) + tz1090_gpio_irq_next_edge(bank, hw); + + BUG_ON(!tz1090_gpio_valid_handler(child_desc)); + generic_handle_irq_desc(irq_no, child_desc); + } +} + +static int tz1090_gpio_irq_map(struct irq_domain *d, unsigned int irq, + irq_hw_number_t hw) +{ + irq_set_chip(irq, &gpio_irq_chip); + return 0; +} + +static const struct irq_domain_ops tz1090_gpio_irq_domain_ops = { + .map = tz1090_gpio_irq_map, + .xlate = irq_domain_xlate_twocell, +}; + +static int tz1090_gpio_bank_probe(struct tz1090_gpio_bank_info *info) +{ + struct device_node *np = info->node; + struct device *dev = info->priv->dev; + struct tz1090_gpio_bank *bank; + + bank = devm_kzalloc(dev, sizeof(*bank), GFP_KERNEL); + if (!bank) { + dev_err(dev, "unable to allocate driver data\n"); + return -ENOMEM; + } + + /* Offset the main registers to the first register in this bank */ + bank->reg = info->priv->reg + info->index * 4; + + /* Set up GPIO chip */ + snprintf(bank->label, sizeof(bank->label), "tz1090-gpio-%u", + info->index); + bank->chip.label = bank->label; + bank->chip.dev = dev; + bank->chip.direction_input = tz1090_gpio_direction_input; + bank->chip.direction_output = tz1090_gpio_direction_output; + bank->chip.get = tz1090_gpio_get; + bank->chip.set = tz1090_gpio_set; + bank->chip.free = tz1090_gpio_free; + bank->chip.request = tz1090_gpio_request; + bank->chip.to_irq = tz1090_gpio_to_irq; + bank->chip.of_node = np; + + /* GPIO numbering from 0 */ + bank->chip.base = info->index * 30; + bank->chip.ngpio = 30; + + /* Add the GPIO bank */ + gpiochip_add(&bank->chip); + + /* Get the GPIO bank IRQ if provided */ + bank->irq = irq_of_parse_and_map(np, 0); + + /* The interrupt is optional (it may be used by another core on chip) */ + if (bank->irq < 0) { + dev_info(dev, "IRQ not provided for bank %u, IRQs disabled\n", + info->index); + return 0; + } + + dev_info(dev, "Setting up IRQs for GPIO bank %u\n", + info->index); + + /* + * Initialise all interrupts to disabled so we don't get + * spurious ones on a dirty boot and hit the BUG_ON in the + * handler. + */ + tz1090_gpio_write(bank, REG_GPIO_IRQ_EN, 0); + + /* Add a virtual IRQ for each GPIO */ + bank->domain = irq_domain_add_linear(np, + bank->chip.ngpio, + &tz1090_gpio_irq_domain_ops, + bank); + + /* Setup chained handler for this GPIO bank */ + irq_set_handler_data(bank->irq, bank); + irq_set_chained_handler(bank->irq, tz1090_gpio_irq_handler); + + return 0; +} + +static void tz1090_gpio_register_banks(struct tz1090_gpio *priv) +{ + struct device_node *np = priv->dev->of_node; + struct device_node *node; + + for_each_available_child_of_node(np, node) { + struct tz1090_gpio_bank_info info; + u32 addr; + int ret; + + ret = of_property_read_u32(node, "reg", &addr); + if (ret) { + dev_err(priv->dev, "invalid reg on %s\n", + node->full_name); + continue; + } + if (addr >= 3) { + dev_err(priv->dev, "index %u in %s out of range\n", + addr, node->full_name); + continue; + } + + info.index = addr; + info.node = of_node_get(node); + info.priv = priv; + + ret = tz1090_gpio_bank_probe(&info); + if (ret) { + dev_err(priv->dev, "failure registering %s\n", + node->full_name); + of_node_put(node); + continue; + } + } +} + +static int tz1090_gpio_probe(struct platform_device *pdev) +{ + struct device_node *np = pdev->dev.of_node; + struct resource *res_regs; + struct tz1090_gpio priv; + + if (!np) { + dev_err(&pdev->dev, "must be instantiated via devicetree\n"); + return -ENOENT; + } + + res_regs = platform_get_resource(pdev, IORESOURCE_MEM, 0); + if (!res_regs) { + dev_err(&pdev->dev, "cannot find registers resource\n"); + return -ENOENT; + } + + priv.dev = &pdev->dev; + + /* Ioremap the registers */ + priv.reg = devm_ioremap(&pdev->dev, res_regs->start, + res_regs->end - res_regs->start); + if (!priv.reg) { + dev_err(&pdev->dev, "unable to ioremap registers\n"); + return -ENOMEM; + } + + /* Look for banks */ + tz1090_gpio_register_banks(&priv); + + return 0; +} + +static struct of_device_id tz1090_gpio_of_match[] = { + { .compatible = "img,tz1090-gpio" }, + { }, +}; + +static struct platform_driver tz1090_gpio_driver = { + .driver = { + .name = "tz1090-gpio", + .owner = THIS_MODULE, + .of_match_table = tz1090_gpio_of_match, + }, + .probe = tz1090_gpio_probe, +}; + +static int __init tz1090_gpio_init(void) +{ + return platform_driver_register(&tz1090_gpio_driver); +} +subsys_initcall(tz1090_gpio_init); |