diff options
| -rw-r--r-- | drivers/input/touchscreen/ads7846.c | 12 | ||||
| -rw-r--r-- | drivers/mtd/devices/m25p80.c | 50 | ||||
| -rw-r--r-- | drivers/mtd/devices/mtd_dataflash.c | 28 | ||||
| -rw-r--r-- | drivers/spi/spi.c | 18 | ||||
| -rw-r--r-- | drivers/spi/spi_bitbang.c | 86 | ||||
| -rw-r--r-- | include/linux/spi/spi.h | 92 | ||||
| -rw-r--r-- | include/linux/spi/spi_bitbang.h | 7 |
7 files changed, 180 insertions, 113 deletions
diff --git a/drivers/input/touchscreen/ads7846.c b/drivers/input/touchscreen/ads7846.c index c741776ef3bf..dd8c6a9ffc76 100644 --- a/drivers/input/touchscreen/ads7846.c +++ b/drivers/input/touchscreen/ads7846.c @@ -155,10 +155,13 @@ static int ads7846_read12_ser(struct device *dev, unsigned command) struct ser_req *req = kzalloc(sizeof *req, SLAB_KERNEL); int status; int sample; + int i; if (!req) return -ENOMEM; + INIT_LIST_HEAD(&req->msg.transfers); + /* activate reference, so it has time to settle; */ req->xfer[0].tx_buf = &ref_on; req->xfer[0].len = 1; @@ -192,8 +195,8 @@ static int ads7846_read12_ser(struct device *dev, unsigned command) /* group all the transfers together, so we can't interfere with * reading touchscreen state; disable penirq while sampling */ - req->msg.transfers = req->xfer; - req->msg.n_transfer = 6; + for (i = 0; i < 6; i++) + spi_message_add_tail(&req->xfer[i], &req->msg); disable_irq(spi->irq); status = spi_sync(spi, &req->msg); @@ -398,6 +401,7 @@ static int __devinit ads7846_probe(struct spi_device *spi) struct ads7846 *ts; struct ads7846_platform_data *pdata = spi->dev.platform_data; struct spi_transfer *x; + int i; if (!spi->irq) { dev_dbg(&spi->dev, "no IRQ?\n"); @@ -500,8 +504,8 @@ static int __devinit ads7846_probe(struct spi_device *spi) CS_CHANGE(x[-1]); - ts->msg.transfers = ts->xfer; - ts->msg.n_transfer = x - ts->xfer; + for (i = 0; i < x - ts->xfer; i++) + spi_message_add_tail(&ts->xfer[i], &ts->msg); ts->msg.complete = ads7846_rx; ts->msg.context = ts; diff --git a/drivers/mtd/devices/m25p80.c b/drivers/mtd/devices/m25p80.c index 71a072103a7f..45108ed85588 100644 --- a/drivers/mtd/devices/m25p80.c +++ b/drivers/mtd/devices/m25p80.c @@ -245,6 +245,21 @@ static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, if (from + len > flash->mtd.size) return -EINVAL; + spi_message_init(&m); + memset(t, 0, (sizeof t)); + + t[0].tx_buf = flash->command; + t[0].len = sizeof(flash->command); + spi_message_add_tail(&t[0], &m); + + t[1].rx_buf = buf; + t[1].len = len; + spi_message_add_tail(&t[1], &m); + + /* Byte count starts at zero. */ + if (retlen) + *retlen = 0; + down(&flash->lock); /* Wait till previous write/erase is done. */ @@ -254,8 +269,6 @@ static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, return 1; } - memset(t, 0, (sizeof t)); - /* NOTE: OPCODE_FAST_READ (if available) is faster... */ /* Set up the write data buffer. */ @@ -264,19 +277,6 @@ static int m25p80_read(struct mtd_info *mtd, loff_t from, size_t len, flash->command[2] = from >> 8; flash->command[3] = from; - /* Byte count starts at zero. */ - if (retlen) - *retlen = 0; - - t[0].tx_buf = flash->command; - t[0].len = sizeof(flash->command); - - t[1].rx_buf = buf; - t[1].len = len; - - m.transfers = t; - m.n_transfer = 2; - spi_sync(flash->spi, &m); *retlen = m.actual_length - sizeof(flash->command); @@ -313,6 +313,16 @@ static int m25p80_write(struct mtd_info *mtd, loff_t to, size_t len, if (to + len > flash->mtd.size) return -EINVAL; + spi_message_init(&m); + memset(t, 0, (sizeof t)); + + t[0].tx_buf = flash->command; + t[0].len = sizeof(flash->command); + spi_message_add_tail(&t[0], &m); + + t[1].tx_buf = buf; + spi_message_add_tail(&t[1], &m); + down(&flash->lock); /* Wait until finished previous write command. */ @@ -321,26 +331,17 @@ static int m25p80_write(struct mtd_info *mtd, loff_t to, size_t len, write_enable(flash); - memset(t, 0, (sizeof t)); - /* Set up the opcode in the write buffer. */ flash->command[0] = OPCODE_PP; flash->command[1] = to >> 16; flash->command[2] = to >> 8; flash->command[3] = to; - t[0].tx_buf = flash->command; - t[0].len = sizeof(flash->command); - - m.transfers = t; - m.n_transfer = 2; - /* what page do we start with? */ page_offset = to % FLASH_PAGESIZE; /* do all the bytes fit onto one page? */ if (page_offset + len <= FLASH_PAGESIZE) { - t[1].tx_buf = buf; t[1].len = len; spi_sync(flash->spi, &m); @@ -352,7 +353,6 @@ static int m25p80_write(struct mtd_info *mtd, loff_t to, size_t len, /* the size of data remaining on the first page */ page_size = FLASH_PAGESIZE - page_offset; - t[1].tx_buf = buf; t[1].len = page_size; spi_sync(flash->spi, &m); diff --git a/drivers/mtd/devices/mtd_dataflash.c b/drivers/mtd/devices/mtd_dataflash.c index a39b3b6b266c..99d3a0320fc9 100644 --- a/drivers/mtd/devices/mtd_dataflash.c +++ b/drivers/mtd/devices/mtd_dataflash.c @@ -147,7 +147,7 @@ static int dataflash_erase(struct mtd_info *mtd, struct erase_info *instr) { struct dataflash *priv = (struct dataflash *)mtd->priv; struct spi_device *spi = priv->spi; - struct spi_transfer x[1] = { { .tx_dma = 0, }, }; + struct spi_transfer x = { .tx_dma = 0, }; struct spi_message msg; unsigned blocksize = priv->page_size << 3; u8 *command; @@ -162,10 +162,11 @@ static int dataflash_erase(struct mtd_info *mtd, struct erase_info *instr) || (instr->addr % priv->page_size) != 0) return -EINVAL; - x[0].tx_buf = command = priv->command; - x[0].len = 4; - msg.transfers = x; - msg.n_transfer = 1; + spi_message_init(&msg); + + x.tx_buf = command = priv->command; + x.len = 4; + spi_message_add_tail(&x, &msg); down(&priv->lock); while (instr->len > 0) { @@ -256,12 +257,15 @@ static int dataflash_read(struct mtd_info *mtd, loff_t from, size_t len, DEBUG(MTD_DEBUG_LEVEL3, "READ: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]); + spi_message_init(&msg); + x[0].tx_buf = command; x[0].len = 8; + spi_message_add_tail(&x[0], &msg); + x[1].rx_buf = buf; x[1].len = len; - msg.transfers = x; - msg.n_transfer = 2; + spi_message_add_tail(&x[1], &msg); down(&priv->lock); @@ -320,9 +324,11 @@ static int dataflash_write(struct mtd_info *mtd, loff_t to, size_t len, if ((to + len) > mtd->size) return -EINVAL; + spi_message_init(&msg); + x[0].tx_buf = command = priv->command; x[0].len = 4; - msg.transfers = x; + spi_message_add_tail(&x[0], &msg); pageaddr = ((unsigned)to / priv->page_size); offset = ((unsigned)to % priv->page_size); @@ -364,7 +370,6 @@ static int dataflash_write(struct mtd_info *mtd, loff_t to, size_t len, DEBUG(MTD_DEBUG_LEVEL3, "TRANSFER: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]); - msg.n_transfer = 1; status = spi_sync(spi, &msg); if (status < 0) DEBUG(MTD_DEBUG_LEVEL1, "%s: xfer %u -> %d \n", @@ -385,14 +390,16 @@ static int dataflash_write(struct mtd_info *mtd, loff_t to, size_t len, x[1].tx_buf = writebuf; x[1].len = writelen; - msg.n_transfer = 2; + spi_message_add_tail(x + 1, &msg); status = spi_sync(spi, &msg); + spi_transfer_del(x + 1); if (status < 0) DEBUG(MTD_DEBUG_LEVEL1, "%s: pgm %u/%u -> %d \n", spi->dev.bus_id, addr, writelen, status); (void) dataflash_waitready(priv->spi); + #ifdef CONFIG_DATAFLASH_WRITE_VERIFY /* (3) Compare to Buffer1 */ @@ -405,7 +412,6 @@ static int dataflash_write(struct mtd_info *mtd, loff_t to, size_t len, DEBUG(MTD_DEBUG_LEVEL3, "COMPARE: (%x) %x %x %x\n", command[0], command[1], command[2], command[3]); - msg.n_transfer = 1; status = spi_sync(spi, &msg); if (status < 0) DEBUG(MTD_DEBUG_LEVEL1, "%s: compare %u -> %d \n", diff --git a/drivers/spi/spi.c b/drivers/spi/spi.c index 3ecedccdb96c..cdb242de901d 100644 --- a/drivers/spi/spi.c +++ b/drivers/spi/spi.c @@ -557,6 +557,17 @@ int spi_write_then_read(struct spi_device *spi, if ((n_tx + n_rx) > SPI_BUFSIZ) return -EINVAL; + spi_message_init(&message); + memset(x, 0, sizeof x); + if (n_tx) { + x[0].len = n_tx; + spi_message_add_tail(&x[0], &message); + } + if (n_rx) { + x[1].len = n_rx; + spi_message_add_tail(&x[1], &message); + } + /* ... unless someone else is using the pre-allocated buffer */ if (down_trylock(&lock)) { local_buf = kmalloc(SPI_BUFSIZ, GFP_KERNEL); @@ -565,18 +576,11 @@ int spi_write_then_read(struct spi_device *spi, } else local_buf = buf; - memset(x, 0, sizeof x); - memcpy(local_buf, txbuf, n_tx); x[0].tx_buf = local_buf; - x[0].len = n_tx; - x[1].rx_buf = local_buf + n_tx; - x[1].len = n_rx; /* do the i/o */ - message.transfers = x; - message.n_transfer = ARRAY_SIZE(x); status = spi_sync(spi, &message); if (status == 0) { memcpy(rxbuf, x[1].rx_buf, n_rx); diff --git a/drivers/spi/spi_bitbang.c b/drivers/spi/spi_bitbang.c index 44aff198eb96..f037e5593269 100644 --- a/drivers/spi/spi_bitbang.c +++ b/drivers/spi/spi_bitbang.c @@ -146,6 +146,9 @@ int spi_bitbang_setup(struct spi_device *spi) struct spi_bitbang_cs *cs = spi->controller_state; struct spi_bitbang *bitbang; + if (!spi->max_speed_hz) + return -EINVAL; + if (!cs) { cs = kzalloc(sizeof *cs, SLAB_KERNEL); if (!cs) @@ -172,13 +175,8 @@ int spi_bitbang_setup(struct spi_device *spi) if (!cs->txrx_word) return -EINVAL; - if (!spi->max_speed_hz) - spi->max_speed_hz = 500 * 1000; - - /* nsecs = max(50, (clock period)/2), be optimistic */ + /* nsecs = (clock period)/2 */ cs->nsecs = (1000000000/2) / (spi->max_speed_hz); - if (cs->nsecs < 50) - cs->nsecs = 50; if (cs->nsecs > MAX_UDELAY_MS * 1000) return -EINVAL; @@ -194,7 +192,7 @@ int spi_bitbang_setup(struct spi_device *spi) /* deselect chip (low or high) */ spin_lock(&bitbang->lock); if (!bitbang->busy) { - bitbang->chipselect(spi, 0); + bitbang->chipselect(spi, BITBANG_CS_INACTIVE); ndelay(cs->nsecs); } spin_unlock(&bitbang->lock); @@ -244,9 +242,9 @@ static void bitbang_work(void *_bitbang) struct spi_message *m; struct spi_device *spi; unsigned nsecs; - struct spi_transfer *t; + struct spi_transfer *t = NULL; unsigned tmp; - unsigned chipselect; + unsigned cs_change; int status; m = container_of(bitbang->queue.next, struct spi_message, @@ -254,37 +252,49 @@ static void bitbang_work(void *_bitbang) list_del_init(&m->queue); spin_unlock_irqrestore(&bitbang->lock, flags); -// FIXME this is made-up -nsecs = 100; + /* FIXME this is made-up ... the correct value is known to + * word-at-a-time bitbang code, and presumably chipselect() + * should enforce these requirements too? + */ + nsecs = 100; spi = m->spi; - t = m->transfers; tmp = 0; - chipselect = 0; + cs_change = 1; status = 0; - for (;;t++) { + list_for_each_entry (t, &m->transfers, transfer_list) { if (bitbang->shutdown) { status = -ESHUTDOWN; break; } - /* set up default clock polarity, and activate chip */ - if (!chipselect) { - bitbang->chipselect(spi, 1); + /* set up default clock polarity, and activate chip; + * this implicitly updates clock and spi modes as + * previously recorded for this device via setup(). + * (and also deselects any other chip that might be + * selected ...) + */ + if (cs_change) { + bitbang->chipselect(spi, BITBANG_CS_ACTIVE); ndelay(nsecs); } + cs_change = t->cs_change; if (!t->tx_buf && !t->rx_buf && t->len) { status = -EINVAL; break; } - /* transfer data */ + /* transfer data. the lower level code handles any + * new dma mappings it needs. our caller always gave + * us dma-safe buffers. + */ if (t->len) { - /* FIXME if bitbang->use_dma, dma_map_single() - * before the transfer, and dma_unmap_single() - * afterwards, for either or both buffers... + /* REVISIT dma API still needs a designated + * DMA_ADDR_INVALID; ~0 might be better. */ + if (!m->is_dma_mapped) + t->rx_dma = t->tx_dma = 0; status = bitbang->txrx_bufs(spi, t); } if (status != t->len) { @@ -299,29 +309,31 @@ nsecs = 100; if (t->delay_usecs) udelay(t->delay_usecs); - tmp++; - if (tmp >= m->n_transfer) - break; - - chipselect = !t->cs_change; - if (chipselect); + if (!cs_change) continue; + if (t->transfer_list.next == &m->transfers) + break; - bitbang->chipselect(spi, 0); - - /* REVISIT do we want the udelay here instead? */ - msleep(1); + /* sometimes a short mid-message deselect of the chip + * may be needed to terminate a mode or command + */ + ndelay(nsecs); + bitbang->chipselect(spi, BITBANG_CS_INACTIVE); + ndelay(nsecs); } - tmp = m->n_transfer - 1; - tmp = m->transfers[tmp].cs_change; - m->status = status; m->complete(m->context); - ndelay(2 * nsecs); - bitbang->chipselect(spi, status == 0 && tmp); - ndelay(nsecs); + /* normally deactivate chipselect ... unless no error and + * cs_change has hinted that the next message will probably + * be for this chip too. + */ + if (!(status == 0 && cs_change)) { + ndelay(nsecs); + bitbang->chipselect(spi, BITBANG_CS_INACTIVE); + ndelay(nsecs); + } spin_lock_irqsave(&bitbang->lock, flags); } diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index 6a41e2650b2e..939afd3a2e72 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -263,15 +263,16 @@ extern struct spi_master *spi_busnum_to_master(u16 busnum); /** * struct spi_transfer - a read/write buffer pair - * @tx_buf: data to be written (dma-safe address), or NULL - * @rx_buf: data to be read (dma-safe address), or NULL - * @tx_dma: DMA address of buffer, if spi_message.is_dma_mapped - * @rx_dma: DMA address of buffer, if spi_message.is_dma_mapped + * @tx_buf: data to be written (dma-safe memory), or NULL + * @rx_buf: data to be read (dma-safe memory), or NULL + * @tx_dma: DMA address of tx_buf, if spi_message.is_dma_mapped + * @rx_dma: DMA address of rx_buf, if spi_message.is_dma_mapped * @len: size of rx and tx buffers (in bytes) * @cs_change: affects chipselect after this transfer completes * @delay_usecs: microseconds to delay after this transfer before * (optionally) changing the chipselect status, then starting * the next transfer or completing this spi_message. + * @transfer_list: transfers are sequenced through spi_message.transfers * * SPI transfers always write the same number of bytes as they read. * Protocol drivers should always provide rx_buf and/or tx_buf. @@ -279,11 +280,16 @@ extern struct spi_master *spi_busnum_to_master(u16 busnum); * the data being transferred; that may reduce overhead, when the * underlying driver uses dma. * - * All SPI transfers start with the relevant chipselect active. Drivers - * can change behavior of the chipselect after the transfer finishes - * (including any mandatory delay). The normal behavior is to leave it - * selected, except for the last transfer in a message. Setting cs_change - * allows two additional behavior options: + * If the transmit buffer is null, undefined data will be shifted out + * while filling rx_buf. If the receive buffer is null, the data + * shifted in will be discarded. Only "len" bytes shift out (or in). + * It's an error to try to shift out a partial word. (For example, by + * shifting out three bytes with word size of sixteen or twenty bits; + * the former uses two bytes per word, the latter uses four bytes.) + * + * All SPI transfers start with the relevant chipselect active. Normally + * it stays selected until after the last transfer in a message. Drivers + * can affect the chipselect signal using cs_change: * * (i) If the transfer isn't the last one in the message, this flag is * used to make the chipselect briefly go inactive in the middle of the @@ -299,7 +305,8 @@ extern struct spi_master *spi_busnum_to_master(u16 busnum); * The code that submits an spi_message (and its spi_transfers) * to the lower layers is responsible for managing its memory. * Zero-initialize every field you don't set up explicitly, to - * insulate against future API updates. + * insulate against future API updates. After you submit a message + * and its transfers, ignore them until its completion callback. */ struct spi_transfer { /* it's ok if tx_buf == rx_buf (right?) @@ -316,12 +323,13 @@ struct spi_transfer { unsigned cs_change:1; u16 delay_usecs; + + struct list_head transfer_list; }; /** * struct spi_message - one multi-segment SPI transaction - * @transfers: the segements of the transaction - * @n_transfer: how many segments + * @transfers: list of transfer segments in this transaction * @spi: SPI device to which the transaction is queued * @is_dma_mapped: if true, the caller provided both dma and cpu virtual * addresses for each transfer buffer @@ -333,14 +341,22 @@ struct spi_transfer { * @queue: for use by whichever driver currently owns the message * @state: for use by whichever driver currently owns the message * + * An spi_message is used to execute an atomic sequence of data transfers, + * each represented by a struct spi_transfer. The sequence is "atomic" + * in the sense that no other spi_message may use that SPI bus until that + * sequence completes. On some systems, many such sequences can execute as + * as single programmed DMA transfer. On all systems, these messages are + * queued, and might complete after transactions to other devices. Messages + * sent to a given spi_device are alway executed in FIFO order. + * * The code that submits an spi_message (and its spi_transfers) * to the lower layers is responsible for managing its memory. * Zero-initialize every field you don't set up explicitly, to - * insulate against future API updates. + * insulate against future API updates. After you submit a message + * and its transfers, ignore them until its completion callback. */ struct spi_message { - struct spi_transfer *transfers; - unsigned n_transfer; + struct list_head transfers; struct spi_device *spi; @@ -371,6 +387,24 @@ struct spi_message { void *state; }; +static inline void spi_message_init(struct spi_message *m) +{ + memset(m, 0, sizeof *m); + INIT_LIST_HEAD(&m->transfers); +} + +static inline void +spi_message_add_tail(struct spi_transfer *t, struct spi_message *m) +{ + list_add_tail(&t->transfer_list, &m->transfers); +} + +static inline void +spi_transfer_del(struct spi_transfer *t) +{ + list_del(&t->transfer_list); +} + /* It's fine to embed message and transaction structures in other data * structures so long as you don't free them while they're in use. */ @@ -383,8 +417,12 @@ static inline struct spi_message *spi_message_alloc(unsigned ntrans, gfp_t flags + ntrans * sizeof(struct spi_transfer), flags); if (m) { - m->transfers = (void *)(m + 1); - m->n_transfer = ntrans; + int i; + struct spi_transfer *t = (struct spi_transfer *)(m + 1); + + INIT_LIST_HEAD(&m->transfers); + for (i = 0; i < ntrans; i++, t++) + spi_message_add_tail(t, m); } return m; } @@ -402,6 +440,8 @@ static inline void spi_message_free(struct spi_message *m) * device doesn't work with the mode 0 default. They may likewise need * to update clock rates or word sizes from initial values. This function * changes those settings, and must be called from a context that can sleep. + * The changes take effect the next time the device is selected and data + * is transferred to or from it. */ static inline int spi_setup(struct spi_device *spi) @@ -468,15 +508,12 @@ spi_write(struct spi_device *spi, const u8 *buf, size_t len) { struct spi_transfer t = { .tx_buf = buf, - .rx_buf = NULL, .len = len, - .cs_change = 0, - }; - struct spi_message m = { - .transfers = &t, - .n_transfer = 1, }; + struct spi_message m; + spi_message_init(&m); + spi_message_add_tail(&t, &m); return spi_sync(spi, &m); } @@ -493,16 +530,13 @@ static inline int spi_read(struct spi_device *spi, u8 *buf, size_t len) { struct spi_transfer t = { - .tx_buf = NULL, .rx_buf = buf, .len = len, - .cs_change = 0, - }; - struct spi_message m = { - .transfers = &t, - .n_transfer = 1, }; + struct spi_message m; + spi_message_init(&m); + spi_message_add_tail(&t, &m); return spi_sync(spi, &m); } diff --git a/include/linux/spi/spi_bitbang.h b/include/linux/spi/spi_bitbang.h index 8dfe61a445f4..c961fe9bf3eb 100644 --- a/include/linux/spi/spi_bitbang.h +++ b/include/linux/spi/spi_bitbang.h @@ -31,8 +31,15 @@ struct spi_bitbang { struct spi_master *master; void (*chipselect)(struct spi_device *spi, int is_on); +#define BITBANG_CS_ACTIVE 1 /* normally nCS, active low */ +#define BITBANG_CS_INACTIVE 0 + /* txrx_bufs() may handle dma mapping for transfers that don't + * already have one (transfer.{tx,rx}_dma is zero), or use PIO + */ int (*txrx_bufs)(struct spi_device *spi, struct spi_transfer *t); + + /* txrx_word[SPI_MODE_*]() just looks like a shift register */ u32 (*txrx_word[4])(struct spi_device *spi, unsigned nsecs, u32 word, u8 bits); |