diff options
-rw-r--r-- | Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt | 18 | ||||
-rw-r--r-- | drivers/spi/spi-armada-3700.c | 8 | ||||
-rw-r--r-- | drivers/spi/spi-atmel.c | 2 | ||||
-rw-r--r-- | drivers/spi/spi-rspi.c | 4 | ||||
-rw-r--r-- | drivers/spi/spi-sun4i.c | 2 | ||||
-rw-r--r-- | drivers/spi/spi-xilinx.c | 11 | ||||
-rw-r--r-- | include/linux/spi/spi.h | 2 |
7 files changed, 36 insertions, 11 deletions
diff --git a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt index 5bf13960f7f4..e3c48b20b1a6 100644 --- a/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt +++ b/Documentation/devicetree/bindings/spi/fsl-imx-cspi.txt @@ -12,24 +12,30 @@ Required properties: - "fsl,imx53-ecspi" for SPI compatible with the one integrated on i.MX53 and later Soc - reg : Offset and length of the register set for the device - interrupts : Should contain CSPI/eCSPI interrupt -- cs-gpios : Specifies the gpio pins to be used for chipselects. - clocks : Clock specifiers for both ipg and per clocks. - clock-names : Clock names should include both "ipg" and "per" See the clock consumer binding, Documentation/devicetree/bindings/clock/clock-bindings.txt -- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, - Documentation/devicetree/bindings/dma/dma.txt -- dma-names: DMA request names should include "tx" and "rx" if present. -Obsolete properties: -- fsl,spi-num-chipselects : Contains the number of the chipselect +Recommended properties: +- cs-gpios : GPIOs to use as chip selects, see spi-bus.txt. While the native chip +select lines can be used, they appear to always generate a pulse between each +word of a transfer. Most use cases will require GPIO based chip selects to +generate a valid transaction. Optional properties: +- num-cs : Number of total chip selects, see spi-bus.txt. +- dmas: DMA specifiers for tx and rx dma. See the DMA client binding, +Documentation/devicetree/bindings/dma/dma.txt. +- dma-names: DMA request names, if present, should include "tx" and "rx". - fsl,spi-rdy-drctl: Integer, representing the value of DRCTL, the register controlling the SPI_READY handling. Note that to enable the DRCTL consideration, the SPI_READY mode-flag needs to be set too. Valid values are: 0 (disabled), 1 (edge-triggered burst) and 2 (level-triggered burst). +Obsolete properties: +- fsl,spi-num-chipselects : Contains the number of the chipselect + Example: ecspi@70010000 { diff --git a/drivers/spi/spi-armada-3700.c b/drivers/spi/spi-armada-3700.c index 77fe55ce790c..d65345312527 100644 --- a/drivers/spi/spi-armada-3700.c +++ b/drivers/spi/spi-armada-3700.c @@ -79,6 +79,7 @@ #define A3700_SPI_BYTE_LEN BIT(5) #define A3700_SPI_CLK_PRESCALE BIT(0) #define A3700_SPI_CLK_PRESCALE_MASK (0x1f) +#define A3700_SPI_CLK_EVEN_OFFS (0x10) #define A3700_SPI_WFIFO_THRS_BIT 28 #define A3700_SPI_RFIFO_THRS_BIT 24 @@ -220,6 +221,13 @@ static void a3700_spi_clock_set(struct a3700_spi *a3700_spi, prescale = DIV_ROUND_UP(clk_get_rate(a3700_spi->clk), speed_hz); + /* For prescaler values over 15, we can only set it by steps of 2. + * Starting from A3700_SPI_CLK_EVEN_OFFS, we set values from 0 up to + * 30. We only use this range from 16 to 30. + */ + if (prescale > 15) + prescale = A3700_SPI_CLK_EVEN_OFFS + DIV_ROUND_UP(prescale, 2); + val = spireg_read(a3700_spi, A3700_SPI_IF_CFG_REG); val = val & ~A3700_SPI_CLK_PRESCALE_MASK; diff --git a/drivers/spi/spi-atmel.c b/drivers/spi/spi-atmel.c index f95da364c283..669470971023 100644 --- a/drivers/spi/spi-atmel.c +++ b/drivers/spi/spi-atmel.c @@ -1661,12 +1661,12 @@ static int atmel_spi_remove(struct platform_device *pdev) pm_runtime_get_sync(&pdev->dev); /* reset the hardware and block queue progress */ - spin_lock_irq(&as->lock); if (as->use_dma) { atmel_spi_stop_dma(master); atmel_spi_release_dma(master); } + spin_lock_irq(&as->lock); spi_writel(as, CR, SPI_BIT(SWRST)); spi_writel(as, CR, SPI_BIT(SWRST)); /* AT91SAM9263 Rev B workaround */ spi_readl(as, SR); diff --git a/drivers/spi/spi-rspi.c b/drivers/spi/spi-rspi.c index 2ce875764ca6..0835a8d88fb8 100644 --- a/drivers/spi/spi-rspi.c +++ b/drivers/spi/spi-rspi.c @@ -377,8 +377,8 @@ static int qspi_set_config_register(struct rspi_data *rspi, int access_size) /* Sets SPCMD */ rspi_write16(rspi, rspi->spcmd, RSPI_SPCMD0); - /* Enables SPI function in master mode */ - rspi_write8(rspi, SPCR_SPE | SPCR_MSTR, RSPI_SPCR); + /* Sets RSPI mode */ + rspi_write8(rspi, SPCR_MSTR, RSPI_SPCR); return 0; } diff --git a/drivers/spi/spi-sun4i.c b/drivers/spi/spi-sun4i.c index c5cd635c28f3..41410031f8e9 100644 --- a/drivers/spi/spi-sun4i.c +++ b/drivers/spi/spi-sun4i.c @@ -525,7 +525,7 @@ err_free_master: static int sun4i_spi_remove(struct platform_device *pdev) { - pm_runtime_disable(&pdev->dev); + pm_runtime_force_suspend(&pdev->dev); return 0; } diff --git a/drivers/spi/spi-xilinx.c b/drivers/spi/spi-xilinx.c index bc7100b93dfc..e0b9fe1d0e37 100644 --- a/drivers/spi/spi-xilinx.c +++ b/drivers/spi/spi-xilinx.c @@ -271,6 +271,7 @@ static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t) while (remaining_words) { int n_words, tx_words, rx_words; u32 sr; + int stalled; n_words = min(remaining_words, xspi->buffer_size); @@ -299,7 +300,17 @@ static int xilinx_spi_txrx_bufs(struct spi_device *spi, struct spi_transfer *t) /* Read out all the data from the Rx FIFO */ rx_words = n_words; + stalled = 10; while (rx_words) { + if (rx_words == n_words && !(stalled--) && + !(sr & XSPI_SR_TX_EMPTY_MASK) && + (sr & XSPI_SR_RX_EMPTY_MASK)) { + dev_err(&spi->dev, + "Detected stall. Check C_SPI_MODE and C_SPI_MEMORY\n"); + xspi_init_hw(xspi); + return -EIO; + } + if ((sr & XSPI_SR_TX_EMPTY_MASK) && (rx_words > 1)) { xilinx_spi_rx(xspi); rx_words--; diff --git a/include/linux/spi/spi.h b/include/linux/spi/spi.h index 7b2170bfd6e7..bc6bb325d1bf 100644 --- a/include/linux/spi/spi.h +++ b/include/linux/spi/spi.h @@ -126,7 +126,7 @@ void spi_statistics_add_transfer_stats(struct spi_statistics *stats, * for that name. This appears in the sysfs "modalias" attribute * for driver coldplugging, and in uevents used for hotplugging * @cs_gpio: gpio number of the chipselect line (optional, -ENOENT when - * when not using a GPIO line) + * not using a GPIO line) * * @statistics: statistics for the spi_device * |